User Manual of RF-668 PIR Sensor Dialer Alarm Setting
Contents
1. User Manual of RF 668 PIR Sensor Dialer Alarm 9 gt 10 ie 12 13 7 14 8 1 TX status LED 8 AC DC adaptor Input 2 Off Chime button 9 Mode Selection Switch 4 Away Panic 11 Phone Line socket 5 PIR Sensor 12 Tone Selection 6 Siren 13 Reset Button 7 Status LED s 14 Battery compartment system Set Up A Door Contact You could make the selection for the alarm trigger but door closing or opening Al Opening Trigger Connect the attached magnetic contact tothe main unit 10 And putthe magnetand sensor together A2 Closing Trigger Connect the attached magnetic contact tothe main unit 10 And keep the magnet contact separate A3 Open the 9 Volt battery compartment Insert the 9 Volt battery and connect tothe battery clip Hits if skipped the door contact selection procedure then insert the 9 Volt battery first then the system will set the door as closing B Entry the Phone Numbers B1 Slide the mode selection switch 9 to the Prog Position B2 Slide the Tone selection switch 12 to Tone position B3 Push the number buttons the keypad should be respond with a single short beep for every button B4 Pushthe STORE button onthe keypad B5 Keyin the phone numbers While keyin the phone numbers system will resoond witha short beep tone If your phone system need to dial a digit first for line release please also keyin this digit to your memory B6 Keyin the memory n2. and hold the Away Panic button for 3seconds Live Listening Once the alarm was triggered System will dial out the pre set numbers and provide 30 seconds live listening tothe outsider Outsider could hear listening what s happen inside the house office During this 30 seconds the outsider will hear asilgnt warnning beep tone every 5 seconds Important Hits You MUST advanced the owner of your calling list about the system operation Therefore they will know you need their help while they getsuch phone call
3. ld be stop within the entry delay by push the disarm button once 29 System will resoond with 2 beep sound 30 If no disarm signal then system will dial the pre set phone number M1 M2 M3 31 After the phone dialling system will release the telephone line and back to ARM mode Hits if you setthe mode switch to Alarm position then system will blast the siren sound for 60 seconds after the dialling Then stay atthe ARM mode again Away Mode 32 Push the Away button once to arm the system 33 System will start the exit delay and go to ARM mode after the exit delay 34 System will be triggered bythe PIR sensor or door contact 35 System will start the entry delay and entry alert beep while detected the movement or a opening door or window 36 Disarm the system by push the Disarm button within the entry delay 37 System will dial the pre set phone numbers M1 M2 M3 and release the line after dialling Disarm 38 You could disarm the system by push the disarm button at any time 39 You could stop the dialling atany time by push down the disarm button 40 You could stop the siren atany time by push down the disarm button Mute Alert system designed with manual mute alert function 40 Push and hold the Home Mufe alert button for 3seconds It will activate the dialer system automatically 4 System will dial the pre set phone number quietly Panic 42 You could blast the siren atany time by push
4. te Disarm Chime You could activate the visitor chime function while the system atthe disarm mode by push the Disarm Chime button Activate the Chime by door opening closing a Pushthe Disarm Chime button on your remote unit once system will resoond with one ding dong sound Now the chime ls activated it willsound the bell when the dooropen orclose Activate the Chime by PIR movement sensor b Push the Disarm Chime button twice system will resoond with two Ding Dong sound Now Ihe chime Is activated It will blast the bell when the sensor detected the movement inthe detection area Disable the chime Push the Disarm chime button once You willhear the system respond with the disarm beep Hits this function is special design for small shop office as anvisitor chime or simple entry alert Home Mode disable the PIR sensor Usethe system while you stay athome 21 Push the Home Mute Alert button once 22 System will resoond with 3beep sound and start the exit delay 15 seconds the status LED red will flashing 23 Along beep sound will activate after the exit delay 24 System will gointo the Arm mode automatically after the exit delay 25 system will disable the PIR sensor toallow free movement inside the house or you leave your pets at home 26 System will activate while the door contact was triggered 27 System will start the entry delay with an entry alert beep 40 seconds 28 System cou
5. umbers ie M1 System will respond with tones sound as confirm signal Store Phone number M1 M1 Repeat the procedure of B4 to Bd to input the 2nd and 3rd phone number B7 After input the telephone numbers Please switch the tone selection switch 12 to the correct position to matching your phone system Hits If your system didn t respond with the key in tones Please use a small pinto push the reset button 13 once to reset your system C CodeLearning C1 Slide the Mode Selection switch 9 to the Mute position C2 Push your remote button once the remote will senda radio signal to the main unit C3 Main unit willresoond with 4 beeps as learnt confirmation C4 Ifyou had 2nd remote then push the remote button of your 2nd remote once Hits System will leave the learn mode onceit receipt 2 codes Or after 10 seconds of the first code learning Installation Wall mount hanger Wall mount bracket slot Door Contact Line socket Battery compartment Connect the door contact switch to the door or window withthe provide double side sticker Connect the wires of the door contact to the main unit Connect the telephone line tothe main unit Hang it onthe wall by screw Or 5 Hang it on some where as you want butthe mounting bracket Hits The PIR sensor should be always watching onthe direction you want to be protect such as main entry a E Operation with remo
Download Pdf Manuals
Related Search