Installation Manual - Designer Appliances
Contents
1. 6 6 3 DISPOSAL Remove the drain connection plug before attaching the drain hose from the dishwasher Every disposal has a hook up for a dishwasher consult your disposer manual for correct connection Figure C o 6 7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation At the end of the cycle when the dishwasher door is opened it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top 6 6 2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop clean the area with a damp cloth as shown in Figure A Once the area dries apply the steam protection foil The steam protection foil will be applied at the location where the hot steam escapes when you first open the door as shown in Figure B CAUTION Steam protection foil must be applied where the steam escapes when door is first opened Failure to install the steam protection foil during installation can lead to damage to the cabinets and countertop 10 0 7 PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections os A caution Make sure all hoses are pulled through the side opening of the cabinet no hoses are kinked and all slack is taken out as shown in the above figure gt 7 1 DRAIN HOSE C2. teeth of the bracket C 3 Now attach the toe kick to the bracket with the two 3 4 6 x 1 4 4mm x 6mm screws and the caps provided as follows 15 GS If the enclosure height is below 331 46 840mm use only o labelled toe kick toe kick without slots Installation should be done following the steps illustrated in the Figures A B and C respectively 1 Bend tabs on toe kick 0 inwards A 2 Secure toe kick to brackets with screws t as shown in the supply bags B 3 Attach caps s as shown in the supply bags C If the enclosure height is above 331 46 840mm use o and p labelled toe kicks together Make sure the slotted toe kick p is on the outside so you can adjust height of the toe kick Installation should be done following the steps illustrated in the figures A B and C respectively 1 Align the toe kick o and p A 2 Secure toe kicks to brackets with screws t after adjusting the height of the slotted toe kick p B 3 Attach caps s as shown in the supply bags C 7 4 INSTALLING THE OUTER DOOR ER DWT 54100 FBI DWT 55100 FBI DWT 55200 gt SE FBIWS DWT 57500 FBI 5 Measure the height and width of the enclosure Figure A and the toe kick Determine how big the wooden door can be For example if the height is 337 8 860mm and if the toe kick is 319 46 100mm the door can not be taller than 291 116 A 7
3. a properly rated protected and sized power supply circuit to avoid electrical overload The dishwasher is designed for an electrical supply of 120 V volts 60 Hz hertz AC connected to a dishwasher dedicated properly grounded electrical circuit with a fuse or breakers rated for 15 amperes Electrical supply conductors shall be a minimum of 16 AWG copper wire rated at 75 C 167 F or higher These requirements must be met to prevent injury and machine damage Consult a qualified electrician if in doubt Do not use any extension cord or portable outlet device to connect the dishwasher to a power supply Ensure that any plastic wrappings bags small pieces etc are disposed of safely and kept out of the reach of children Danger of suffocation Remove the door to the washing compartment when removing an old dishwasher from service or discarding it Ensure that the appliance presents no danger to children while being stored for disposal Old appliances may contain materials that can be recycled Please contact your local recycling authority about the possibility of recycling these materials i Notice e The dishwasher drain hose must be installed with a drain loop at least 28 710mm off the cabinet floor otherwise the dishwasher may not drain properly e This dishwasher is intended for residential use only and should not be used in commercial establishments e New installation If the dish
4. 60mm 1 Prepare the wooden door with the mounting brackets Height Height of the wooden door 30 760mm Width 123 w to 23 2 592mm 595mm Thickness 74 19mm 16 0 2 To take the plastic bracket out remove the screws on it Screws will be used in 5th step again Figure B 3 Mark the wooden door as shown in the drawing Figure C Max 12 1 Ib Mid Point 5 5 kg 4 Place the plastic mounting brackets over the marked holes and the side tabs must be flush with the edge of the wooden door Figure D 5 Attach the two mounting brackets to the wooden door with 4 screws 1 g x 5 8 3 5mm x 14mm Figure A 6 Mount the wooden door onto the dishwasher with the plastic mounting brackets which you have attached Figure B 7 Open the door and remove the two caps and two screws inside the door at position 1 and 4 Figure C 18 8 Using the four screws 3 46 x 111 46 4mm x 43mm provided attach the wooden door to the dishwasher at position 1 and 4 Figure A 9 Check the position of the wooden door and make sure it is aligned properly Figure B 10 Tighten the screws in position 1 and 4 completely after the final alignment Figure C 11 Check whether the bottom of the door hits the toe kick of the kitchen cabinet A 11 1 If the door hits the toe
5. Dishwasher Installation Manual FOR MODELS DWT 23100 B DWT 25100 W DWT 54100 FBI DWT 55200 SSWS DWT 23100 SS DWT 25200 BWS DWT 54100 SS DWT 55200 WWS DWT 23100 W DWT 25200 SSWS DWT 54100 W DWT 55300 FBI DWT 24100 B DWT 25200 WWS DWT 54400 SS ULTRA DWT 55300 B DWT 24100 SS DWT 25300 B DWT 54400 W ULTRA DWT 55300 W DWT 24100 SSP DWT 25300 W DWT 55100 B DWT 55300 SS DWT 24100 W DWT 25300 SS DWT 55100 FBI DWT 55500 SS DWT 24400 SS ULTRA DWT 25500 B DWT 55100 SS DWT 57500 B DWT 24400 W ULTRA DWT 25500 W DWT 55100 W DWT 57500 FBI DWT 25100 B DWT 25500 SS DWT 55200 BWS DWT 57500 SS DWT 25100 SS DWT 54100 B DWT 55200 FBIWS DWT 57500 W BI DWT 57550 SS Installation Manual For Dishwasher Models DWT 23100 B DWT 23100 SS DWT 23100 W DWT 24100 B DWT 24100 SS DWT 24100 SSP DWT 24100 W DWT 54100 B DWT 54100 FBI DWT 54100 SS DWT 54100 W DWT 54400 SS ULTRA DWT 54400 W ULTRA DWT 55100 B DWT 55100 FBI DWT 24400 SS ULTRA DWT 24400 W ULTRA DWT 25100 B DWT 25100 SS DWT 25100 W DWT 25200 BWS DWT 25200 SSWS DWT 25200 WWS DWT 25300 B DWT 25300 W DWT 25300 SS DWT 25500 B DWT 25500 W DWT 25500 SS DWT 55100 SS DWT 55100 W DWT 55200 BWS DWT 55200 FBIWS DWT 55200 SSWS DWT 55200 WWS DWT 55300 FBI DWT 55300 B m en Be DWT 55300 W DWT 55300 SS DWT 55500 SS DWT 57500 B DWT 57500 FBI DWT 57500 SS DWT 57500 W DWT 57550 SS To prevent accidents which could cause serious injury or death as well as machi
6. ING The dishwasher is designed for an electrical supply of 120 V 60 Hz AC connected to a dishwasher dedicated properly grounded electrical circuit with a fuse or breaker rated for 15 amperes 6 2 PREPARATION FOR INSTALLING MOUNTING BRACKETS WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided Failure to do this may cause damage to property or bodily injury Place the two mounting brackets into the top corners of the dishwasher Fix the mounting brackets A to the top corners of the dishwasher with the screws supplied Bend sides of mounting brackets B in order to fix from sides if necessary 6 3 ADJUSTING HEIGHT If the height of the enclosure is 337 8 to A 357 8 861 mm 911mm adjust supports as shown in the figure ap 1 RE gE e Supplied 4 Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height Adjust the rear foot level with a screwdriver to balance and raise the dishwasher to the enclosure height Li Notice e Make sure the dishwasher is plumb and notice dishwasher can be placed with a small clearance under the counter top e Turning the screwdriver in the direction of the black arrows will bring the dishwasher back feet up e Turning the screwdriver in the direction of the white arrows will take the dishwasher rear feet dow
7. ONNECTION WATER SUPPLY 6 ELECTRICAL CONNECTIONS 7 1 1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing 1 Use the supplied rubber connection hose and drain hose clamps to connect the dishwasher drain hose to the plumbing drain connection 2 Use the spring clamp to secure the rubber connection hose to the dishwasher drain hose Use the screw clamp to secure the rubber connection hose to the plumbing drain connection Note that the marks on the rubber connection hose should be on the drain hose side 7 1 2 PREPERATION OF WATER SUPPLY Left side water supply connection Before pushing the dishwasher in to the cabinet you must place water supply hoses into the channel of the dishwasher Figure A Place the supplied clips into the channel Figure B so that you can move these clips along the channel Figure C and fix by pressing on Figure D so that you can keep the water supply hose in the channel 1210 After installing one clip for each side push the dishwasher into the cabinet Figure E Note that while pushing the dishwasher into the cabinet water supply hose must move in the channel to the front Figure F Fix the second clip Figure G 7 1 3 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways e With metal braided hose e With copper tubing CAUTION e Ho
8. kick cut the necessary section out of the toe kick B 11 2 Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture ADJUSTING DOOR TENSION WITH CUSTOM WOODEN DOOR DWT 54100 FBI DWT 55100 FBI DWT 55200 FBIWS DWT 57500 FBI Check the door tension of the dishwasher If the door closes too quickly or if the door falls open the spring tension needs to be adjusted The adjustment screws can be found on the front of the dishwasher after you et open the door see drawing Adjust the spring tension by turning the screw to the right for more weight and to the left for less weight Figure C 20 Gs Li Notice If you have a European kitchen or want to install a wooden toe kick to match your kitchen please refer to one of the two drawings given below Follow the same instructions on the brackets as for the removable toe kick Installation should be done following the steps illustrated in the figures A B C D respectively BN See also page 15 JEZ See also page 20 Li Notice The installer is responsible for the dishwasher installation Incorrect installation is not covered by the warranty 21 GD 8 INSTALLER CHECKLIST Your installer must have completed and checked the following e The dishwasher is square and level e The dishwasher is fastened securely to the cabinetry e The dishwasher door opens and closes freel
9. ks inside The information icon also will provide important references WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Indicates a potentially hazardous situation which if not avoided may result in injury It may also be used to alert against unsafe practices Notice Indicates a potentially hazardous situation which if not avoided may result in damage to the dishwasher the table ware the equipment or the environment 1 IMPORTANT SAFETY INSTRUCTIONS In addition to these instructions the dishwasher shall be installed e In accordance with all local codes or in absence of a local code e In the United States with the National Electric Code e In Canada with the Canadian Electric Code C22 1 latest edition Provincial and Municipal codes and or local codes i Notice Read these installation instructions completely before installing and follow them carefully Save these installation instructions and pass them on to any future user WARNING When installing the dishwasher follow basic precautions including the following e The dishwasher installation must be performed in accordance with this installation manual If you did not receive an installation manual order it by calling 1 800 459 9848 or you may also download it from our web site at www blombergappliances com e The dishwasher could only be converted from cord con
10. must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop 1 Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop make sure the unit is level 2 Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied 3 Attach the dishwasher underneath the countertop with the four screws supplied 1 8 x 1 8 3 5mm x 14mm Make sure you do not go through the top of the countertop or damage granite 7 3 ADJUSTING THE MOVABLE TOE KICK Now that you have successfully installed the dishwasher you need to attach the toe kick to the dishwasher The two piece toe kick can be adjusted to the height and depth needed for your kitchen Be sure to use the slotted toe kick in the front and the other behind it They slide into each other 1 Insert the movable toe kick brackets into the channel A 2 Make sure that the plastic tab to the left of the L opening on the dishwasher has not closed the channel you will push the bracket through Li Notice Be sure to notice there is a left and a right bracket Adjust the toe kick brackets forward or backwards so that they will align with the kitchen toe kick B Lock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into the
11. n 6 4 INSTALLING THE SIDE TRIM STRIPS 1 Remove the adhesive tape Figure A Place the trim strips on the front edge of the side walls Figure B Li Notice e Make sure you use the correct trim strip since there is a left and right side strip The flexible material should be facing forward Figure B T 6 5 PREPARING THE WATER CONNECTION A Install an easily accessible shut off valve not supplied in the water supply line All solder connections must be made before the water line is connected to the dishwasher s water inlet valve Water can also be supplied to the dishwasher by using a flexible braided hose line Check with your plumbing supply sources for the proper hose and 90 elbow and necessary fittings for the water supply line This material is not supplied and must be purchased separately WARNING Installation should be performed by a qualified installer Work by unqualified persons could be dangerous and may void the warranty If the dishwasher is installed in a location that experiences freezing temperatures e g in a vacation home cabin etc you must drain all the water from the dishwasher s interior Water system ruptures that occur as a result of freezing are not covered by warranty 6 5 1 INSTALLING THE 90 ELBOW FITTING B CAUTION Do not over tighten the 90 elbow Doing so may damage the water inlet valve and cause a water leak If the water supply line is to be co
12. ne damage read these instructions before installation and or use Contents 1 IMPORTANT SAFETY INSTRUCTIONS 1 1 INSPECT THE DISHWASHER 1 2 HOW TO CONTACT US 2 TOOLS WHICH MAY BE NEEDED 3 MATERIALS WHICH MAY BE NEEDED 4 MATERIALS SUPPLIED 4 1 PARTS SUPPLIED 4 2 MANUAL BAG 4 3 DISHWASHER PARTS BAG 1 4 4 DISHWASHER PARTS BAG 2 4 5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER 5 DISHWASHER SPECIFICATIONS 5 1 TECHNICAL FEATURES 6 ENCLOSURE PREPARATION 6 1 ELECTRICAL PREPARATION 6 2 PREPARATION FOR INSTALLING MOUNTING BRACKETS 6 3 ADJUSTING HEIGHT 6 4 INSTALLING THE SIDE TRIM STRIPS 6 5 PREPARING THE WATER CONNECTION A 6 6 DRAIN PREPARATION 6 7 STEAM PROTECTION FOIL M Oo Oo oO OO HRA KAA RP O O DPD ND oo 7 PLACEMENT OF DISHWASHER INTO THE OPENING 7 1 DRAIN HOSE CONNECTION WATER SUPPLY amp ELECTRICAL CONNECTIONS 7 2 READJUSTING FOOT LEVELS 7 3 ADJUSTING THE MOVABLE TOE KICK 7 4 INSTALLING THE OUTER DOOR _ _ ui ee ey o O1 O1 8 INSTALLER CHECKLIST N N 9 FINAL INSTRUCTIONS N N 10 SELF HELP HINTS N N INTRODUCTION Please read this installation manual and particularly the safety instructions completely and carefully They will save you time and effort and help to ensure optimum dishwasher performance Be sure to observe all listed warnings and cautions Look particularly for the icons with exclamation mar
13. nected to permanently connected by an authorized service representative If needed contact your dealer to schedule an authorized service agent for conversion with an appropriate conversion kit e Installation and repair should be performed by a qualified installer Work by unqualified persons could be dangerous and may void the warranty Li Notice The dishwasher should be installed by an insured licensed plumber contractor or trained installer Installation performed by persons other than this could result in improper installation and property damage e Do not operate the appliance if damaged malfunctioning partially disassembled or if it has missing or broken parts e Also follow the safety instructions of the user manual e To reduce the risk of electric shock fire or injury to persons the installer must ensure that the dishwasher is completely enclosed at the time of installation e Only connect the dishwasher to the power supply when all installation and plumbing work is complete 1 If the dishwasher is installed in a location that experiences freezing temperatures e g in a vacation home cabin etc you must drain all the water from the dishwasher s interior Water system ruptures that occur as a result of freezing are not covered by warranty Dishwasher must be secured to adjacent cabinetry using the brackets provided Failure to do this may cause damage to property or bodily injury Connect to
14. ng or metal braided dishwasher supply line 90 elbow with 3 8 N P T male threads on one leg and sized to fit your water supply line copper tubing compression fitting or braided hose on the other leg UL listed conduit connector or strain relief Teflon tape or other pipe thread compound to seal plumbing connections Shut off valve and fittings appropriate for hot water supply line copper tubing compression fitting or braided hose Silicone Ly Glue 3 so 4 MATERIALS SUPPLIED 4 1 PARTS SUPPLIED a x1 Parts for your dishwasher will come in several plastic bags Check your parts bags shown to make sure you have all the b x1 parts as listed to the left x1 4 2 MANUAL BAG The dishwasher comes with a manual bag containing x6 e User manual e Installation manual and x1 e Quick reference guide ae ass sq ES x1 4 3 DISHWASHER PARTS BAG 1 This dishwasher bag comes with the following parts lt gt x1 a Side Trim Strips Left b Side Trim Strips Right h ES x1 c Adjusting Wrench s z d Screws 1 8 x 5 8 3 5 mm x 14 mm x1 e Mounting Bracket Left f Mounting Bracket Right g Spring Clamp h Screw Clamp x1 j Rubber Connector X1 k Toe Kick Bracket Left I Toe Kick Bracket Right m mx m Edge Protector n Clips i _x2 o Toe Kick toe kick with
15. out slots Bs p Toe Kick r Screws 1 8 x 3 8 3 9 mm x 9 mm o ee x1 s Plastic Caps t Screws 3 16 x 1 4 4mm x 6mm p co x1 z Steam Protection Foil r kr x2 4 4 DISHWASHER PARTS BAG 2 In addition to the manual bag and the dishwasher parts bag 1 s _ x2 DWT 54 DWT 55 and DWT 57 dishwasher models which can accept a wooden kitchen door also come with a door panel t how x2 installation kit which contains v Screws 1 8 x 5 8 3 5mm x 14mm v p x2 y Screws 3 16 x 13 4 4mm x 43mm y aS a 4 5 PARTS ATTACHED TO THE REAR OF THE i DISHWASHER GE a Side Trim Strips Left ZE x b Side Trim Strips Right o Toe Kick toe kick without slots p Toe Kick 4 5 DISHWASHER SPECIFICATIONS gt 3614 864mm 920mm 34 33 Tlg 35 ur 861mm 911mm 5 1 TECHNICAL FEATURES Load capacity 14 place settings Permissible water pressure 4 35 145 psi 0 3 10 bars Electrical connection 120 V volts 12 A amps 60Hz hertz Total power 1400 W watts 1240 W watts Li Notice Because we continually strive to improve our products we may change our specifications and design without prior notice This device corresponds to the following directives UL 749 Household Dishwasher directive 5 6 ENCLOSURE PREPARATION 6 1 ELECTRICAL PREPARATION WARN
16. pper tubing make certain that the elbow has a compression fitting Apply Teflon tape or other pipe sealant when required Orient the water supply connection downwards as shown in the figure so the water line can be easily pulled underneath or on the side of the dishwasher IO 6 6 DRAIN PREPARATION The dishwasher drain hose may be connected to the drain plumbing in one of three ways Figure A B C Li Notice e Either one of the above methods must be used or the dishwasher will not operate properly e Ahose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher If your sink has one it is recommended that the hose be disconnected and the hole plugged e The total length of the drain hose is 763 4 1950mm If a hose extension is required a drainage hose of equal quality must be used e The maximum length must not exceed 157 4000mm Otherwise the cleaning process is negatively influenced 6 6 1 UNDER THE SINK DRAIN Install a Y branch tail pipe Figure A O Notice e You must add a loop at least 28 710mm above the floor of the cabinet and above the drain connection in the drain hose to prevent waste water from not draining properly and causing either poor washing results or a bad odor 6 6 2 INSTALLING AN AIR GAP If the local ordinance requires an air gap Figure B Li Notice e Check with local ordinance for type of air gap required
17. rge enough for the attachment plug to pass through The longest dimension of the opening shall not be more than 1 5 38 mm If the partition is metal it needs to be covered with an edge protector e Care must be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord 7 1 5 GROUNDING INSTRUCTIONS This appliance must be grounded In the event of a malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances This appliance must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the appliance WARNING e Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician 14 7 2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you
18. t water supply line Use minimum 3 8 O D copper tubing or metal braided dishwasher supply line e Temperatures required for soldering and sweating will damage the dishwasher s water inlet valve so if any such operation is needed keep the heat source min 7118 200mm away from the dishwasher s water inlet valve e There should not be any sharp bends in the water line that may restrict the water flow e Teflon tape or pipe tread compound must be used for sealing the connection Before connecting the copper water supply line to the dishwasher flush it with hot water to clear any foreign material Li Notice After connections are made turn on the water supply to check for leaks 7 1 4 ELECTRICAL CONNECTION ZA WARNING e Make sure the voltage and frequency listed on the data plate correspond with the household electrical supply This data must correspond to prevent injury and machine damage Consult a qualified electrician if in doubt e Only connect the dishwasher to the mains when all installation and plumbing work is complete e Do not use any extension cord or portable outlet device to connect the dishwasher to a power supply e The power supply receptacle for the appliance shall be installed in a cabinet or ona wall adjacent to the undercounter space in which the appliance is to be installed e The access hole of the supply cord to the installation compartment must be smooth and rounded and it must be la
19. the on position e Check to make sure that the Supply cord is plugged No Water is coming into the dishwasher e Check to make sure the hot water shut off is in the ON position Water does not drain e Make sure drain hose is not kinked or comes out of air gap next to the sink e Remove drain hose from disposal making sure plug is removed Li Notice e If your dishwasher is not operating properly after following these steps Contact your dealer to schedule an authorized service agent to inspect your new dishwasher for any function related failure e The manufacturer warranty does not cover installation conversion or customer education service visits You will find the model and serial number information on the label located on the right hand side of the inner door of your dishwasher as shown above 12A 60Hz Blomberg MODEL NUMBER NUM RO DE MOD LE FT 3000000000 120V 1 2A Stock Number x00000000 Serial Number xxxxxxxxxx Made in Turkey Li Notice Please make a copy of your invoice and keep it with this manual and register your dishwasher on line 22 Gs 17 9077 01 00 AC USA
20. washer is a new installation most of the work must be done before the dishwasher is moved into place e Replacement If the dishwasher is replacing another dishwasher check the existing dishwasher connections for compatibility with the new dishwasher and replace parts as necessary 1 1 INSPECT THE DISHWASHER After unpacking the dishwasher and prior to installation thoroughly inspect the dishwasher for possible freight or cosmetic damage Report any damage immediately Li Notice e Cosmetic defects must be reported within 10 days of installation e Do not discard any bags or items that come with the original package until after the entire installation has been completed 1 2 HOW TO CONTACT US You may either call our Toll Free Number at 1 800 459 9848 or contact us via the web site at www blombergappliances com or Contact the Blomberg Distributor for your State or Province as listed on the Distributor Contact List provided 2 2 TOOLS WHICH MAY BE NEEDED Pipe Wrench Wire Cutter Drill Hole Saw Hammer Wire Stripper IEEE 120 Tape Measure Torx Screwdriver Phillips Screwdriver Adjustable Wrench Scot Screwdriver Scissors Leve Brush Pencil 3 MATERIALS WHICH MAY BE NEEDED Additional materials may be required to comply with local codes Hot Water Supply Line Minimum 3 8 O D copper tubi
21. y The dishwasher door must close without hitting any cabinetry or counter top e The inlet water supply is turned on and checked for leaks e The drain hose has been connected and checked for leaks There must be no kinks or obstructions in the drain hose e The drain hose must be installed with a 28 710mm high drain loop for drain hook ups without any air removed e f the dishwasher drain is hooked up to a garbage disposal the drain hopper plug must be removed e The spray arms are free and rotate freely e The rinse cycle has been run e The water level will be below the filter screen after the end of the wash program It is normal to find some water in the drain filter area e Set the water softener to the correct water hardness for your area If the dishwasher drain is connected to a garbage disposal make sure that the drain hopper plug has been removed 9 FINAL INSTRUCTIONS 1 Press the On Off button to turn the dishwasher on 2 Power indicator light comes on 3 Use the Program Select button to choose a washing program 4 Start the program with the Start Pause Cancel button 5 Run the dishwasher through one complete cycle When the wash cycle is completed use the On Off button to turn the dishwasher off Li Notice If the dishwasher does not operate properly refer to the self help hints 10 SELF HELP HINTS The screen does not come on e Check to make sure the breaker to the dishwasher is in
Download Pdf Manuals
Related Search