RT Controller
Contents
1. Let go of the roller The value of the end Move the roller to the right and find the level is shown position on the roller where it takes about 8 sec for the bucket to rotate comple o gt tely Keep the roller in this position and press 360 8s JS Let go of the Repeat step 3b but in roller the rollers opposite direction left If you move the rol ler to the right as much as possible but notice that the rotor bucket won t make a full circle O gt in 8 sec then keep _ holding the roller to the right and press gt Then let go of the roller and redo step 3b for the direction concerned a Ge The feeder s end levels tilt Repeat step 3b for the tilt but this Find the position on the roller where it takes time you move the roller control 4 sec for the tilt bucket to move from side ling the tilt to the right and then to side Hold the roller in this position and press 6 to the left Note Move the roller as little as possible to achieve the 4 sec tilt from one side to the other ROS Gu The feeder s end levels shifted in grip If you do not have a shifted in grip go on to step 4 The feeder s end level for the grip you set f button see the Connecting the SVAB Grip only if you have the grip connected via L8 to the RT Controller sheet a shifted in roller onlin FAS For a shifted in grip you repeat step 3b but instead of only moving the roller N2. Then press the _ let go of the _ and press the middle The preset is now com middle button rollers 2 button again plete Make sure nothing or noone is near P a the rotortilt 3 then start the machine Make sure the machines digging functions are If you need to redo the preset see enabled the red safety bar The rotor and the RT user manual v 2 1 and tilt should now move as you move the rollers forward page 78 ch 9 18 Reca ae or memorize which roller controls which libration The unction RT user manual comes with the RT Controller and should be placed in the machines cabin How you navigate in the RT Controller Main menu Settings that adapts the RT system to the machine are made in the main menu From the operating mode press and hold arrow down je tO access the main menu Return Endlevels Start levels Feeder setLings Information Output settings Recalibration Rampt ime Copy banks To browse in the menu you use the buttons EJ and J To make a selection press To return to the operating mode select Return Wherever you are in the menu you can press and hold O for about 3 seconds to return to the operating mode Select Bark A Tip If you by accident select the bank selection menu make sure Bank A is selected and press O to get back to the operating mode If you want to know more about how you easily config
3. m certain I set the start and end levels correctly The magnets on the valves can be more sensitive than usual lower the ripple amplitude from 45 to 20 See the RT user manual page 80 ch 9 19 Ripple I have read your instructions carefully set the start and end levels accordingly but the rotor tilt still doesn t move as fast as I want it to Your machine might have a slightly higher servo pressure than what s common and you the refore need a stronger feeder The usual feeder s are 20bar but there are also 32bar feeder s which often solves this problem Call SVAB for further information or ordering Tel 46 582 152 30 My rotor tilt starts with a powerful jerk Your external valves start levels are probably set too low Try increasing them some See step 4 Start levels for the external valves in this instruction The feeder s start level might also be set too high Try lowering it some See step 3a The feeder s start level in this instruction The rotor stops with a jerk when I let go of the roller Check the oil pressure to the rotor tilt this should never be above 230bar My machine sounds very strained when I use the rotor tilt grip slowly Increase the start level of the external valves for the concerned function See step 4 Start levels for the external valves in this instruction SVAB Hydraulik AB Tel 46 582 152 30 www svab se
4. level rotation tilt in this instruction and try to set the levels lower than you did the last time If the problems persists try increasing the end level of the external valves See the RT user manual page 55 ch 7 6 End levels I get full speed on the rotor tilt without having reached the end position of the rol ler The feeder s end level is set too high see step 3b 3d The feeder s end level rotation tilt grip in this instruction and try to set the levels lower than you did the last time Rotor tilt grip goes faster when several functions are run simultaneously The feeder s end level is set too low see step 3a The feeder s start level in this instruc tion and try to set the levels higher than you did the last time Rotor tilt grip goes slower when several functions are ran simultaneously The feeder s max level might be set too low See the RT user manual page 53 ch 7 4 Feeder s max level in the RT user manual and increase the max level slightly My rotor tilt grip runs too slow which is caused by the feeder s end level beeing set too low se step 3c e When I try to increase the end level above a certain value it doesn t work You can never set an end level higher than the max level Try increasing the feeder s max level some and THEN increase the feeder s end level See the RT user manual page 53 ch 7 4 Feeder s max level My rotor tilt grip is twitchy or vibrates at a certain position on the roller and I
5. Get started with the RT Controller A quick guide about how to get started with your RT system Get started with the RT Controller Version 1 3 090831 This instruction works best with the User Manual RT Controller v 2 1 and forward Art no 630009 This work is protected by the Copyright Act and may not be copied distributed or amended Failure to comply with this Act can result in prosecution and fines imprison ment or an obligation to pay compensation to the author owner SVAB Hydraulik AB Tel 46 582 152 30 www svab se 1 d Preset when your RT system is installed both hydraulically and electrical it s time to configure the RT Controller Usually the RT starts when the machines ignition is turned on On earlier models of the RT Controller there is no language selection at start up If you don t see any language selection at startup just skip this part First you select your Scroll through the different Select your language save language languages by pressing the and continue by pressing the arrow keyes Ey and DJ middle button fe Now move each roller to Continue until the Then move the rollers i their end position several black squares m slowly a few times HIMES eects Stops flashing in forward and back the display Ward over the centre max ox position YN LN SVAB Hydraulik AB Tel 46 582 152 30 www svab se 1 Preset cont
6. ess the settings Sharh leweds and Erwileweds The feeders start level is common for all functions rotor tilt grip etc and you oniy have to set it correctly once Ga The feeder s startlevel Select Feecler setLings then During the start and end level settings the rotor Start level in the main menu and tilt are movable in both directions but you Return can only set the level for the chosen direction Endlevels Endlevels Startlevels Start levels Feeder setLings Max levels Information Fixed levels Outrut settings Move the roller controlling the rotor Let go of the roller The value for to the right the startlevel is shown NI Startlev 200200 ASS Gogo Move the roller to the right and find the po Let go of the roller sition on the roller where the rotor bucket rotates with the lowest speed that you want it to have during labour Also make sure that your machine s engine is labouring and not beeing idle Keep the roller in this position and press y You are now done ane D with the feeders start level Dw cont on the next page C gt SVAB Hydraulik AB Tel 46 582 152 30 www svab se Gb The feeder s end level rotation Select Feeder setLLinds then Move the roller which controls the rotor Eridlevels in the main menu to the right nan Return Endlevels Endlevels Startlevels Startlevels N Feeder settings Maxlevels Information Fixed levels Quteut setLings
7. ote You can release the button once the you press and hold the grip s shift in grip is selected SVAB Hydraulik AB Tel 46 582 152 30 www svab se 4 Start levels for the external valves If needed select Feturri and go back to Move the roller which controls the rotor the main menu Select Start levels in to the right the main menu Return Endlevels Startlevels Feeder setLings Information Let go of the The value for the Move the roller to the right and find the po roller start level is shown sition on the roller where the rotor bucket just starts moving Hold the roller in this position and look at the value in the dis play From this value move the roller a bit more to the right until the value increases with 20 then press aay Let go of the roller Now repeat step 4 but in the Repeat step 4 for the tilt and rollers opposite direction its roller left You are now done with the start levels select Return to go back to the operating mode Slutnivaer Startnivaer Putsarinst llningar Information The most necessary settings for the RT Controller and your machine are now completed SVAB Hydraulik AB Tel 46 582 152 30 www svab se Frequently asked questions The machine sounds strained when I use the rotor tilt and the external valves self closes at fast speeds The feeder s end level might be set too high see step 3b 3c The feeder s end
8. ure your machine for several users see the RT user manual p 57 ch 8 N 2d Change position on the rotor tilt If you don t want to change the position or direction go to step 3 When you change position on the outputs Select GubFeul settLings then Siar the roller that controls the rotation will oULFULS in the main menu control the tilt and vice versa Return Return Endlevels Start levels Change direction Feeder setLings Function on off Information Dutput sett ings Recalibration Confirm and return to the menu by pressing 6 SVAB Hvdraulik AB Tel 46 582 152 30 www svab se Change direction of the rotor tilt If you don t want to change the position or direction go to step 3 If your rotor for example rotates clockwise Choose Quteut settings then Change when you move the roller to the left and directianin the main menu you want to change this do the following Return Returri aa a Endlevels Swar outputs Startlevels Change direction Feeder settings Function on off Information Dutput sett ings Recalibration Move the roller controlling the rotor or tilt Let go of the roller and confirm and return depending on what you want to change to the menu by pressing 5 3 Feeder settings To make your rotortilt go as smooth as possible you have to adjust the flow of the feeder so that it is in good relation to the rollers To make the adjustement of the flow you acc
Download Pdf Manuals
Related Search