User-Manual - Volutone.com
Contents
1. Max Input voltage V ON 2 9 6 3 measured between and OFF 0 13 terminals Output current mA ON 50 measured between and terminals OFF 0 1 Applied Voltage Rage 0 80V Table 1 NOTE Both the input and the output are electrically isolated from the rest of the camera s electrical circuitry via general purpose photo couplers The input is additionally protected with a serial 250 Ohm resistor and a debouncing circuit Duration of any input signal should be at least 5 ms to comply with the requirements of the debouncing circuit Orange OUT Yellow OUT White IN Black IN Table 2 12 Page Arecont Vision MegaDome Installation Manual Image 31 Image 31 1 Image 31 2 Connect Here Do NOT Connect Here 13 Page Arecont Vision MegaDome Installation Manual MegaDome Heater Accessory Inside the box 61 Screw the heater board to the standoffs as shown in Image 34 A Heater B Two 2 screws Not included but needed e 1 Phillips head screw driver Image 32 66 Run the heater cable out of the hole in the bottom of the camera and connect it to 10 50VDC power supply 10 Watts max Red is positive cable 67 Remove the heater kit from the box 68 With the heater element protruding out of the camera align the two 2 holes on the heater board with the two standoffs shown in Image 33 14 P2. from the the mounting surface box 33 For installation of the camera please reference Mounting the Camera 6 Page Arecont Vision MegaDome Installation Manual MegaDome Junction Box Adapter Installation Instructions Inside the box A Junction Box Adapter B Pack of four 4 machine screws C Pack of four 4 wood screws and four 4 dry wall anchors D Large round rubber gasket E One double sided hex key Not included but needed e 2 Phillips head screw driver e MegaDome Wall Mount MD WMT e 34 NPT Conduit if necessary Image 15 34 Remove Junction Box and hardware from the box 35 36 37 38 39 40 Image 16 Image 17 Remove the conduit plug by first removing the Socket set screw using one of provided Allen keys shown in Image 16 Attach Junction Box Adapter to the wall using drywall screws or any optional hardware suitable for the mounting surface Attach MegaDome Wall Mount to Junction Box Adapter as shown in Image 17 Connect 34 NPT Conduit to Junction Box Adapter Run Ethernet Cable and outside power cable if necessary through the Junction Box Adapter and Wall Mount For installation of the camera please reference Mounting the Camera 7 Page Arecont Vision MegaDome Installation Manual MegaDome Flush Mount Adapter Installation Instructions Inside the box 45 Screw the lever screws until the FMA is snuggly installed as sho
3. AW Arecont Vision the way in video MegaDome Installation Manual AW Arecont Vision megapixel technology beyond imagination Arecont Vision MegaDome Installation Manual MegaDome Installation Manual Inside the box Mounting the Camera A Arecont Vision MegaDome 1 Remove camera and hardware from the B Mounting template box C Magnetic core 2 Using the Mounting template prepare the D Pack of four 4 wood screws and four 4 mounting provisions for camera dry wall anchors installation NOTE the 19 5mm diameter E One double sided hex key hole on the Mounting template is where F Onesingle sided hex key the Ethernet cable will be exiting the G Security L key MegaDome align accordingly If using H Power cable the side conduit hole please see step 9 below Not included but needed 3 Using Security L key loosen the four 4 screws securing the dome cover Image 2 Remove vandal resistant dome cover NOTE Do not remove screws from the dome cover e 1 Phillips head screw driver e 2 Phillips head screw driver Image 2 Image 1 1 Page Arecont Vision MegaDome Installation Manual 4 Run Ethernet cable through the hole on the bottom of the camera Image 3 and plug it into the RJ45 port NOTE If the camera will be powered via PoE please skip to step 6 5 Ifthe camera is powered by an outside power supply run the supplied power cable through th
4. aDome Pole Mount Adapter Installation Instructions Inside the box 53 Run Ethernet Cable and outside power cable if necessary through the Compress Fittings A Pole Mount Adapter and MegaDome Wall Mount B 2x Compress Fittings C 2xSmall Steel Straps 54 Use the supplied two Steel Straps to attach the D 2xLarge Steel Straps Pole Mount Adapter to the pole and tighten E Pack of four 4 machine screws the compression screws as shown in Image 25 Not included but needed 55 Attach Dome to Wall Mount Adapter Please e 2 Phillips head screw driver reference Mounting the Camera if needed e MegaDome Wall Mount Adapter 56 Tighten the Compress Fittings to seal the wiring holes Image 24 Image 25 50 Remove Pole Mount Adapter Compress Wall Fittings Steel Straps and hardware from the Mount box Adapter 51 Install Compress Fittings to Pole Mount Adapter as shown in Image 25 52 Attach MegaDome Wall Mount Adapter to Pole Mount Adapter as shown in Image 26 Image 26 10 Page Arecont Vision MegaDome Installation Manual MegaDome Corner Mount Adapter Installation Instructions Inside the box A Corner Mount Adapter B 2x Compression Fittings C Pack of four 4 machine screws D 2x Packs of four 4 wood screws and four 4 dry wall anchors Not included but needed e 2 Phillips head screw driver e MegaDome Wall Mount Adapter Image 29 60 Run Ethernet Cable
5. age Arecont Vision MegaDome Installation Manual MegaDome Focus Tool Accessory Inside the box A Focus Tool NOTE Focus Tool is a small piece of bubble which has same material and property as bubble s including thickness curvature and other optical performance Image 36 Image 35 69 Attach Focus Tool on the top of lens shown in Image 36 70 Adjust the lens focus until getting clear image shown image 37 71 Fix the screws on the lens 72 Remove Focus Tool from lens 73 Put bubble and secure it on MegaDome NOTE Focusing Tool is used to compensate Image 37 the focus shift after putting bubble on camera 15 Page leading the way In Megapixel video Arecont Vision 425 E Colorado Street 7th Floor Glendale CA 91205 support arecontvision com www arecontvision com 1 818 937 0700 877 CAMERA 8 ni Arecont Vision megapixel technology beyond imagination R 01 10
6. and outside power cable if necessary through the Compress Fittings and MegaDome Wall Mount Image 27 61 Using the screws provided or other hardware 57 Remove Corner Mount Adapter Compress attach the Corner Mount Adapter to an Fitting and hardware from the box exterior 90 corner wall 58 Install Compress Fittings to Corner Mount 62 Attach Dome to Wall Mount Adapter Please Adapter as shown in Image 28 reference Mounting the Camera if needed 59 Attach Wall Mount Adapter to Corner Mount 63 Tighten the Compress Fittings to seal the Adapter as shown in Image 29 wiring holes 11 Arecont Vision MegaDome Installation Manual MegaDome I O Cable Connection Inside the box A IO Cable Not included but needed 64 65 e Flat head screw driver Image 30 To use the ports of the MegaDome locate the J7 connector NOTE There are two connectors that look identical be sure to use the one adjacent to the capacitor labeled 1000 jFK 8L9 shown in Image 31 1 and NOT the one adjacent to the hole in the back of the camera as shown in Image 31 2 Run the I O cable through the hole in the bottom of the camera and plug it into the J7 connector as shown in image 31 NOTE The connection is a little stiff so be sure to apply enough pressure to connect it using a flat head screw driver to push it in is recommended Electrical Characteristics Min
7. crew driver shown in image 11 23 Attach Dome to Pendant as shown in Image 12 using four machine screws provided 24 Install large round rubber gasket onto Pendant as shown in image 12 Be sure to align the holes appropriately 25 Run Ethernet Cable and outside power cable if necessary through the Pendant 26 Attach Pendant to the ceiling using the four wood screws provided or any optional hardware suitable for the mounting surface Image 10 27 Forinstallation of the camera please 20 Remove Pendant Mount and hardware from reference Mounting the Camera the box 5 Page Arecont Vision MegaDome Installation Manual MegaDome Wall Mount Installation Instructions Inside the box A Top shield and Wall mount B Mounting template C Pack of four 4 machine screws D Pack of four 4 wood screws and four 4 dry wall anchors E Large round rubber gasket Not included but needed e 2 Phillips head screw driver Image 14 29 Using the Mounting template prepare the mounting surface 30 Install large round rubber gasket onto Wall Mount as shown in image 14 Be sure to align the holes appropriately NOTE the four little rubber nipples protrude into the top shield 31 Run Ethernet Cable and outside power cable if necessary through the Wall Mount Image 13 32 Attach Wall Mount to the wall using drywall screws or any optional hardware suitable for 28 Remove Wall Mount and hardware
8. e hole and connect it to its respective connector inside the camera Image 3 NOTE Make sure that your installation of wires complies with Electrical Code of the local government where the camera is installed and no bare wires are exposed 6 Align the holes in the camera with the prepared holes on the mounting surface Attach the camera to the mounting surface with the wood screws or any optional hardware suitable for the mounting surface 7 Install the included magnetic core onto the Ethernet cable as shown in Image 4 NOTE Ensure both tabs are tightly secured Image 4 2 Page Arecont Vision MegaDome Installation Manual 8 Reference Image 5 for proper positioning of Adjusting the Tilt Pan Z axis yaw and Focus the magnetic core 10 To adjust the tilt use a 1 Phillips screwdriver 9 If you are using the side conduit opening to loosen the screw on the side of the plastic remove the conduit plug by first removing the lens bracket 1 4 turn Image 7 CAUTION Socket set screw using one of provided Allen Do not remove the screw keys Image 6 11 Adjust lens tilt as required and tighten the screw from step 10 12 To adjust the pan use a 2 Phillips screwdriver to loosen the screw as shown in Image 7 13 Adjust the pan as required and tighten the screw from step 2 14 To adjust the Z Axis or Yaw for vertical wall mounting loosen the set screw as shown in Image 7 NOTE There are two set sc
9. rews on opposite sides both need to be loosened 15 Adjust the Z Axis as required and tighten the set screw back down Image 6 Image 7 3 Page Arecont Vision MegaDome Installation Manual 16 To adjust back focus loosen the two 2 set screws with the appropriate Allen key as shown Image 8 only one of two screw holes shown Adjust the silver back focus ring as needed and tighten down the set screws 17 focus the lens loosen the three set screws as shown in Image 9 and adjust each as needed A adjusts the zoom B adjusts the iris adjustment is the band between A and C as outlined in red there is no set screw C adjusts the focus 18 Remove the protective film from the camera dome NOTE be cautious not to scratch the vandal dome cover 19 Secure the vandal dome cover to the camera 4 Page Arecont Vision MegaDome Installation Manual MegaDome Pendant Installation Instructions Inside the box Top shield Pendant Mount Mounting template Pack of four 4 machine screws Pack of four 4 small machine screws Pack of four 4 wood screws and four 4 dry wall anchors Large round rubber gasket Image 11 Image 12 Smaller square rubber gasket One double sided hex key mmoowupep 21 Using the Mounting template prepare the mounting provisions for camera installation Not included but needed 22 Place small gasket onto pendant dome as J 2 Phillips head s
10. wn in Image 19 The F Flush Mount Adapter Support Arm will ride down the screw to G White Trim Ring compress the mounting surface NOTE Do H Pack of four 4 machine screws and one not over torque the lever screws 1 I Blot 1 Mounting template 46 Attach the Trim Ring to the Flush Mount Adapter by rotating clockwise as show in Not included but needed Image 20 e 2 Phillips head screw driver Image 18 41 Remove Flush Mount Adapter Trim Ring and hardware from the box 42 Attach Dome to Flush Mount Adapter as shown in Image 19 Please reference Mounting the Camera if needed 43 Using the Mounting template cut a hole in surface for mounting 44 Insert Flush Mount Adapter into the hole Image 20 8 Page Arecont Vision MegaDome Installation Manual MegaDome Electrical Box Adapter Installation Instructions Inside the box A Electrical Box Adapter B Pack of four 4 machine screws Not included but needed e 2 Phillips head screw driver e Common Electrical Box such as single gang box double gang box or square electrical box Image 22 Image 21 47 Remove Electrical Box Adapter and hardware from the box 48 Attach Electrical Box Adapter to Electrical Box as shown in Image 22 Image 23 49 Attach Dome to Electrical Box Adapter as shown in Image 23 Please reference Mounting the Camera if needed 9 Page Arecont Vision MegaDome Installation Manual Meg
Download Pdf Manuals
Related Search