Instruction Guide Sabina 200 - www.liko.com - Hill-Rom
Contents
1. lt 170 cm 67 inch 1 z y 160 190 cm 63 74 8 inch 2 A gt 180 cm 70 9 inch 3 i e ellie f p 1 Lock the two rear wheels Remove the locking 2 handles on the lift mast Then place the lift mast in the foot of the base When the lift mast is secured in the base the lifting height may be adjusted to three different levels Choose one of the three holes The choice of setting depends on the height of the patient see illustration above The distance between the holes is 5 cm 2 inch NY J 3 Use the included locking handles to secure the lift 4 Tighten the locking handles and then adjust them mast to the base so they point downwards N 5 Mount the lower leg support into the bracket Wheel A is used to adjust the depth i e the distance to the patien s lower leg Wheel B is used to adjust the lower leg support s height setting Carefully tighten the wheels after adjustment Sabina 200 7EN155105 04 6 Connect the cables as follows Cable from lift motor to socket 1 Cable from motor for base width adjustment to socket 2 Cable from hand control to socket 3 www liko com A na q 0 Ne D 7 Thread the cables through the opening in the cable 8 Place the quick reference guide in the holder on lid Push the lid up and secure with a screw driver th2. diathermy cables are not positioned on or near the lift If you have questions please consult the responsible assistive device technician or the supplier The lift must not be used in areas where flammable mixtures may occur for example in areas where flammable goods are stored Sabina 200 7EN155105 04 2 www liko com Definitions OMNAARWN gt Technical Data Maximum load 160 kg 350 Ibs Material Powder painted steel Weight Total 42 kg 93 Ibs Heaviest removable part 23 kg 50 Ibs Wheels Standard front 75 mm 2 9 inch twin wheel Standard rear 75 mm 2 9 inch twin wheel Foot rest Removable Lower leg Adjustable height and depth support Removable Turning diameter 1250 mm 49 2 inch Emergency lowering device Lifting interval Electrical 795 mm 31 3 inch Lifting speed without load 20 mm sec 0 9 inch sec Operating forces of controls Electrical data Intermittent power Batteries Battery charger Motor for base width adjustment Lift motor Safety latches Lifting hook Sling bar Motor for lift arm Lower leg support adjustable Foot rest removable Front wheel Base Rear wheel with brake Motor for base width adjustment Locking handles Cable for hand control Hand control Control unit with built in battery Lift mast Manoeuvering handle Lift arm Holder for quick reference guide with colour co
3. make sure that the lifting accessory are selected appropriately in terms of type size material and design with regard to the patient s needs the lifting accessories are not damaged the lifting accessory are correctly and safely applied to the patient in order to avoid bodily injury the lifting accessory is correctly applied to the sling bar the sling bar latches are intact missing or damaged latches must always be replaced the sit to stand vest s straps are properly connected to the sling bar hooks when the vest s straps have been fully extended but before the patient is lifted from the underlying surface as a caregiver assure that the patient not are at risk of falling forward or to any side during lifting A After use store the lift in forward direction towards a wall and out of reach of unauthorized A Never leave a patient unattended in Sabina 200 ETL CLASSIFIED CE Intertek Sabina 200 have been tested by an accredited testing institute and fulfil the requirements specified in the Medical Device Directive 93 42 EEC for Class 1 products Viking S Viking XS complies with the requirements in EN ISO 10535 2006 IEC 60601 1 IEC 60601 1 2 ANSI AAMI ES60601 1 and CAN CSA C22 2 no 60601 1 A Under no circumstances must the lift be modified If you have any questions please contact Liko Hill Rom Particular care must be observed when using strong sources of potential disturbance such as diathermy etc so that
4. raising the raising will be made easier preventing the vest from sliding up The height to which the lift should proceed varies from person to person A Before the patient is lifted from the underlying surface but when the straps have been fully extended make sure the straps are properly connected to the sling bar www liko com Simple Troubleshooting The lift does not work up down gt _ 1 Make sure that the emergency stop is not Base width adjustment does not work engaged page 7 in out 2 Make sure that the control unit cables are connected correctly page 5 3 Make sure that the charging cable is not connected to an electric outlet 4 Check the battery voltage page 8 5 Ifthe problem persists please contact Liko Hill Rom The charger doesn t work gt 1 Make sure that the emergency stop is not engaged page 7 2 Check that the electric outlet is powered 3 Check that the charging cable is correctly connected page 8 4 Ifthe problem persists please contact Liko Hill Rom The lift stops in the high position gt 4 Make sure that the emergency stop is not engaged page 7 2 Use the selected electrical emergency lowering to lower the patient onto a firm surface page 7 3 Check the battery voltage page 8 4 Ifthe problem persists please contact Liko Hill Rom ie NK If you hear unusual sounds gt Contact Liko Hill Rom Sabina 200 7EN155105 04 1
5. 1 www liko com Inspection and Maintenance Care and maintenance For trouble free use certain details should be checked each day the lift is used e Inspect the lift and check to make sure that there is no external damage e Check the sling bar attachment e Check the functionality of the latches e Check raising lowering and base width adjustment e Check to make sure that the emergency lowering functions e Charge the batteries each day the lift is used and make sure the charger works When necessary clean the lift with a moist cloth using common surface cleaners or disinfectants and check that the wheels are free from dirt and hair NOTE Do not use cleaning agents that contain phenol or chlorine since these can damage aluminium and polyamide material A The lift should not be exposed to running water Service Sabina 200 should be inspected at least once a year A Periodic inspection repairs and maintenance may only be carried out in accordance with Liko service manuals by authorized Liko service personnel and using original Liko spare parts Service agreement Liko offers the opportunity to enter into service contracts for the maintenance and regular inspection of your Liko product Expected Lifetime The product has an expected lifetime of 10 years during correct use and with maintenance and periodic inspection carried out in accordance with Liko s instructions Transport and storage During transportation or whe
6. ax min max min 1750 1650 1150 1050 1160 865 575 190 1120 680 1040 550 890 215 1010 910 105 25 1705 810 700 287 322 Measurements in inch A max A min iC D E L 7 B B1 B2 B3 f D1 D2 F F1 M N O max min max min max min max min max min max min 68 9 64 9 45 2 41 3 45 6 34 22 6 7 4 44 26 7 40 9 21 6 35 8 4 39 7 35 8 4 1 1 67 31 8 27 5 11 3 12 6 Different measurements depending on the height setting position please see Assembly p 5 Note The measurements are based on the lift being equipped with standard sling bar and standard wheels When changing to other lifting equipment or wheels check that the lift still achieves desired lifting height Reference measurement according to Standard EN ISO 10535 2006 Sabina 200 7EN155105 04 4 www liko com Assembly Before assembly make sure you have the fol e Lift mast with lift arm control unit and sling bar with safety latches e Base with locking handles Hand control with cable Foot rest and frame for the foot rest lowing parts e Battery charger and cable lid with screws 2 pcs e Lower leg support e Bag with plug for the charger quick reference guide and instruction guide la Individual adjustment of lifting height ok Height of patient Position O
7. de for sling sizes Emergency stop LED yellow light charger connected LED green light lift activated Emergency lowering electrical External charger Buttons on hand control 4 N Button on display 4 N 24V Int Op 10 90 active operation max 2 min Only 10 of a given length of time may be active yet no more than 2 min 2 x 12 V 2 9 Ah valve regulated lead acid gel type batteries New batteries are provided by your Liko representative CH01 100 240 VAC 50 60 Hz max 500 mA 24 V 5A permanent magnetic motor 24 V 9 2 A permanent magnetic motor with mechanical safety mechanism 3 The device is intended for use indoors Sound level 42 dB A Bj d meceni i ype B in accordance wi e electrical shoc Protection class IPX4 N protection class E Class II equipment Sabina 200 7EN155105 04 3 www liko com Measurements Lateral view N a M gt A Amax L y y gt Overhead view lt _ _ _ Max reach of lift arm Q Q ak lt D2 gt Ke 2 Table of measurements Measurements in mm A max A min C D E L B B1 B2 B3 D1 D2 F F1 M N O max min max min max min max min m
8. e lift mast and the accompanying screws 2 pcs a N 1 2 S y a A 9 Release the emergency stop by turning the button in the direction indicated by the arrows on the button 10 Charge the battery by plugging the charger cable into the connector cable Then plug the charger cable into an electric outlet 100 240 V AC The battery is fully charged after approx 12 hours la N After assembly make sure that e the motion of the lift arm corresponds to the buttons e the base width adjustment works on the hand control e the lift charges e the electrical emergency lowering device works e wheel brakes work properly P Sabina 200 7EN155105 04 www liko com Operation a 5 Leal ii mr T T AN OLiko T K J Hand control Sabina 200 is manoeuvred with the push buttons on the hand control For raising and lowering the lift arm push For emergency stop Press the red button on Release the emergency stop by the control unit Resetting the emergency stop turning the button in the direction indicated by the arrows on the a the button with the respective arrow The button direction in which the arrows are pointing applies when the hand control is held as shown in the picture For base width widening and narrowing push 7 and a respectively The movement ceases as soon as the push buttons are released S Lock Unlock j Electrical em
9. ease contact your Liko Hill Rom representative in the event of any uncertainties or questions Table of Contents Salet INStrUClIONS eascair 2 Definition Sarran a aa a ai 3 Technical Data cccceccccccceeeeeeeeeceeeenaecaeeeeeeeeeeetessecsaceeaeeeeeees 3 Measurement ccecceeeeeecenacceeceeeeeeeesececeaanaeceeeeeeeeeeeeeessenaaees 4 Assembly esner n vivid E eddies RS 5 Op ratio sessirnir iaa R aE R E 7 Charging the Batters ssccsaridien ennie 8 Maximum Loads neniateria e a a a a 9 Recommended Lifting Accessories 000 0 eee eeeeeeeeeeeteeeeeeettteeeeeeenaes 9 Raimo Operations escini a 10 Simple Troubleshooting en 11 Inspection and Maintenance cceceeeeeeeeeecceeeeeeeeeeeeeeteeteees 12 A NOTE This instruction guide contains important information for the user of the product All who use the product should review and completely understand the contents of the instruction guide Remember to keep the instruction guide in a place where it is always available to those using the product Safety Instructions Before using make sure that e the lift is assembled in accordance with the assembly instructions e the lifting accessories are properly attached to the lift e the batteries have been charged for at least 12 hours you have read the instruction guides for the lift and lifting accessories personnel using the lift are informed of the correct operation and use of the lift Before lifting always
10. ergency lowering The lift arm is lowered electrically by keeping the button on the control unit pressed in Locking the wheels The rear wheels can be locked to prevent rotating and turning To lock the wheels push down the lock pedal with your foot To unlock the wheels lift up the lock pedal with your foot During raising the wheels should be unlocked so that the lift can be moved to the patient s centre of gravity A Locked wheels during raising can increase the risk of tipping N P Installation of Latches After installation check that the latch locks and runs freely in the sling bar hook Sabina 200 7EN155105 04 A Never move the lift by pulling on the actuator www liko com Charging the Batteries N For maximum battery life batteries must be charged regularly We recommend charging the batteries after use of the lift or every night If the lift is not used every day we recommend pushing in the emergency stop after use in order to turn off the current and save battery power Ensure that the lift is fully charged before pushing the emergency stop A yellow LED A on the control unit s display is lit while the charger is connected to a wall socket Maximum charge is achieved after approx 12 hours When the batteries are fully charged the charger automatically switches to trickle charging When the battery capacity is low when approx 2 10 lifting cycles remain an acoustic s
11. ignal is emitted In this case the lift should be charged as soon as possible Never charge batteries in a wet area The lift cannot be charged with the emergency stop engaged With external charger 1 Connect the charger cable to the charging outlet under the control unit 2 Connect the charger to an electrical outlet 100 240 V AC 2 When the charger is connected a LED displays jesa a yellow light during ongoing charging D 4 Q a green light during trickle charging NOTE The lift cannot be used when the charger cable is plugged into an electric outlet Old batteries are to be deposited at the nearest recycling facility in accordance with local regulations or K Sabina 200 comply with the Directive 2002 96 EC on waste electrical and electronic equipment given to personnel authorized by Liko Hill Rom Sabina 200 7EN155105 04 8 www liko com Maximum Load Different allowable maximum loads may apply to the different products in the assembled lift unit lift sling bar sit to stand vest and any other accessories used For the assembled lift unit the maximum load is always the lowest maximum load rating for any of the components For example a Sabina 200 that is approved for 160 kg 350 Ibs can be equipped with a lifting accessory that is approved for 200 kg 440 Ibs In this case the maximum load of 160 kg 350 Ibs applies to the assembled lift unit Study the markings on
12. n the lift is not to be used for a long time the emergency stop should be engaged The environment where the lift is transported and stored should have a temperature of 10 to 40 C 50 104 F and a relative humidity of 30 to 75 86 167 F The air pressure should be 700 1060 hPa Recycling For instructions on how to recycle your Liko product please visit our website www liko com Product changes Liko s products undergo continuous development which is why we reserve the right to make product changes without prior notice Contact your Liko Hill Rom representative for advice and information about product upgrades Design and Quality by Liko in Sweden Liko is quality certified in accordance with ISO 9001 and its equivalent for the medical device industry ISO 13485 Liko is also certified in accordance with environmental standard ISO 14001 4 Liko a CEAD company www liko com Manufacturer Liko AB SE 975 92 Lule Sweden info liko se Copyright Liko AB 2012 03
13. ons Before using Sabina 200 it is important to make a custom adjustment of the lifting height See page 5 For Sabina 200 there are three different sit to stand vests to choose between Liko SupportVest Mod 91 and Liko SafetyVests Mod 93 and 94 Below is a description on how SupportVest Mod 91 is used See the instruction guide for the respective sit to stand vest for further information 3 N Wa A 1 Place Sabina 200 in front of the patient 2 Raise the sling bar about 10 20 cm 3 9 7 9 inch Adjust the width of the base Place the feet in the middle of the foot rest with the lower legs parallel to the lower leg support Adjust the height and depth of the lower leg support as needed for comfortable support below the kneecap Place the sit to stand vest around the patient in accordance with the instruction guide for the vest Connect the straps of the sit to stand vest s to the sling bar hooks N X A 3 For a more upright position continue the lifting Sabina 200 7EN155105 04 motion to the uppermost position For maximum comfort the lift mast should be affixed to the base in the best possible of the three fastening holes See page 5 When lowering the lift arm the patient must follow the lifting motion downwards This is facilitated if the patient leans backwards 10 The patient grabs the sling bar Continue the lifting procedure If the patient leans backwards during
14. the lift and lifting accessories or contact your Liko Hill Rom representative if you have any questions Recommended Lifting Accessories A Using other lifting accessories than those recommended can entail a risk Below is a description of recommended lifting accessories for Sabina 200 Also for further guidance study the instruction guide for the sit to stand vest or the lifting accessory respectively Contact your Liko Hill Rom representative or visit www liko com for advice and information on Liko s product range Sabina SideSupport Prod No 2027101 Sabina SideSupport is an accessory for patients with reduced lateral stability Sabina Heel Support Prod No 2027011 LASS Heel supports are used if the patient s feet need to AX be fixed to the foot rest Foot straps are included A Be aware of any decreased mobility and or the risk of hyperextension of the knee joints when using Sabina Heel Support Calf strap Prod No 20290022 a l bry SeatStrap SlingBar Prod No 2027006 V S Sabina SeatStrap Prod No 3591115 The SeatStrap is an accessory that facilitates the first part of the raising motion The SeatStrap is connected to Ic a SeatStrap SlingBar which helps the user move the seat up when raising In standing position the SeatStrap can be NOI easily disconnected so that it is not in the way when e g WC going to the toilet STI JA Sabina 200 7EN155105 04 9 www liko com Raising Operati
15. tiko Sabina 200 A GSE company Instruction Guide English 7EN155105 04 2012 03 15 Applies to the following models Sabina 200 Prod No 2020020 GSS ZO E 5 Product Description The Sabina 200 sit to stand lift is especially designed Liko has a wide range of sit to stand vests giving for people who have difficulty in standing up on their different support depending on the patient s needs own from a seated position For patients with poor balance we recommend Sabina 200 is intended for use with patients who are Sabina SideSupport which provides the patient able to actively participate in the raising motion When with extra lateral stability during the raising motion standing they can be moved to a wheelchair or to a as well as in the standing position toilet this gives them standing practice in connection with the transfer In this document the person being lifted is referred to as the patient and the person assisting is referred to as the caregiver Aisa warning triangle used for situations which require extra care and attention cat li IMPORTANT Read the instruction guide for both the patient lift and lifting accessories before use Lifting and transferring a person always involves a certain level of risk It is important to completely understand the contents of the instruction guide The equipment should be used only by trained personnel Pl
Download Pdf Manuals
Related Search