USER MANUAL - Medicaleshop.com
Contents
1. AM wu CHAIR PROVIDER THIS MANUAL MUST BE GIVEN TO THE USER OF THIS DEPENDENT MOBILITY BASE USER READ THIS MANUAL BEFORE USING THIS DEPENDENT MOBILITY BASE AND SAVE FOR FUTURE REFERENCE Product delivered may vary from the one described and pictured in this manual Revision 15 0729 A Authorized Leggero Provider I User Manual Page 2 REACH Table of Contents Section 1 Introduction amp Features 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 Introduction Intended Reach User Intended Reach Attendant Terms of Warranty Service amp Repairs Features Seating amp Positioning Components Adjustability amp Specifications Section 2 Warnings Section 3 Unpacking Your Reach Chair Section 4 Operation and Adjustment 41 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 4 10 411 4 12 Wheel Locks Handlebar Angle Adjustment Knee Angle Adjustment Seat Tilt Angle Adjustment Hip Angle Adjustment Folding Footbed Height Adjustment Back Height Adjustment Seat Depth Adjustment Armrest Adjustment Positioning Tray Using the Reach as a Chair in a Motor Vehicle Section 5 Limited Warranty Section 6 Maintenance and Maintenance Record Page 3 User Manual Page o N Oo a A A A N N N c A a N a O O O N Ci A A CQ CQ 0 N N gt REACH User Manual Section 1 Introduction Warnings amp Features 1 1 Introduction Thank you for selecting2. Do not leave the chair or child in the sun or near other heat sources since the surfaces on the chair may reach temperatures capable of burning the child Do not leave the chair or child outside in cold temperatures because contact with a chair in temperatures below freezing could result in injury Damage to the chair may also result from exposure to extreme hot or cold temperatures WARNING The chair should only be used on solid and level ground Do not attempt to push the chair over or into obstacles Always remove the child from the chair when lifting chair to clear obstacles WARNING Do not use the chair on slopes steeper than 5 degrees Do not leave the chair parked on a slope or an incline Pay particular attention when on slopes and inclines to prevent the child from falling out of the chair the chair from tipping over or the chair from rolling away WARNING Before leaving the chair and before getting into and out of it always engage the wheel locks Do not use the wheel locks to stop the chair while moving Page 9 W7 REACH User Manual WARNING Never leave your child unattended in the chair even if they are strapped in and the wheel locks are engaged WARNING If the chair occupant reaches for objects in front to the side or behind the chair be sure that they do not lean too far The shift in the center of gravity might cause the chair to tip over WARNING Do not stand on the footplate when transferring into or out of th
3. axles of this chair against defects in materials and workmanship for the life of the original purchaser The expected life of this frame is five years C FOR ONE 1 YEAR We warrant all original equipment parts and components of this chair against defects in materials and workmanship for one year from the date of the first consumer purchase D LIMITATIONS 1 We do not warrant Tires tubes upholstery push handle grips or armpads Damage resulting from neglect misuse or from improper installation or repair Damage resulting from transit use Damage from exceeding the weight limit indicated on the serial number label 2 This warranty is valid only when the product is used according to the specified conditions and the intended purposes following all manufacturer recommendations It is void otherwise 3 This warranty shall not apply to problems arising from normal wear and such evaluation will be solely determined by Leggero LLC 4 This warranty is void if the product is modified without Leggero s express written consent including but not limited to modification through the use of unauthorized parts or attachments products damaged by reason of repairs made to any component without specific consent of Leggero or to a product damaged by circumstances beyond Leggero s control and such evaluation will be solely determined by Leggero 5 This warranty is void if the original serial number is removed or altered 6 This warrant
4. problems arise please contact the provider that supplied the chair Authorized providers only replace and install original Leggero spare paris Page 4 REACH CH User Manual 1 6 Features aA Sun amp Weather Shade Adjustable Height Back Armrests Tray Receivers x 7 O t Adjustable Height Footbed Handlebar Angle Adjustment Adjustable Depth Seat Quick Release Rear Wheels Folding Handle Serial Number Label Wheel Lock Lever Page 5 REACH User Manual 1 7 Seating amp Positioning Components LT Back Cushion Therapeutic Positioning Tray Lateral Thoracic Supports Lateral Pelvic Supports W7 Page 6 REACH User Manual 1 8 Adjustability and Specifications Adjustability N Reach 12 Reach 14 Reach 16 Seat Depth 8 13 20 33cm 11 16 28 40cm 13 18 33 46cm Seat Width 12 30cm 14 35cm 16 40cm Seat to Fooplate 8 13 20 33cm 11 16 28 40cm 13 18 33 46cm Max Back Height 18 46cm 21 53cm 24 61cm Hip Angle Adjustment 89 115 89 105 85 95 Seat Angle 10 20 or 30 10 20 or 30 10 20 or 30 Specifications emm menn fmn Ro Tire Diameter 7 18cm T us Rear Tire Diameter Tire Diameter 16 40cm 16 40cm 16 40cm 40cm Folded Dimensions 91x21 5x18 31 x 23 5 x 18 33 x 25 5 x 18 a DF x 55x 46cm 79 x 60 x 46cm x 65 x 46cm PAY
5. the Reach chair This manual explains how to operate adjust and maintain your Reach chair The product as described is subject to technical alterations without notice We are sorry that we cannot offer this user information in a format appropriate for use by visually impaired people The visually Impaired must contact an authorized Leggero provider to obtain information and instruction in the form of verbal communication and hands on training if necessary 1 2 Intended Reach User Rehab pushchairs and pediatric positioning systems are appropriate for children who are limited to a seated position and require mobility and positioning assistance Individuals who need such assistance can have a wide variety of diagnosis limiting their ability to achieve mobility without such a system For maximum occupancy rating and additional specifications reference section 1 7 of this manual 1 3 Intended Reach Attendant Attendants who operate the chair must be visually mentally and physically capable of safely operating the chair under all circumstances Attendants must read and follow all instructions provided in this manual 1 4 Terms of Warranty Warranty applies only when the product is used in concordance with the manufacturer s recommendations and for the intended purposes and specified conditions of the product 1 5 Service and Repairs Service and repair of the Reach chair should be performed only by Leggero authorized providers Should any
6. Lesgero wy ta m 4 N Page 7 REACH User Manual Section 2 Warnings Read this Manual Completely Before Using All caregivers and or attendants must read this user manual prior to operating the Reach chair Familiarize yourself with the handling and functions of the product prior to actual use If there is any information in this manual that you do not understand please contact your authorized Leggero provider for assistance Failure to follow instructions or comply with warnings within this manual could result in personal injury and or damage to the Reach chair potentially voiding the warranty Symbols Used on Product Warning Labels and in User Manual WARNING The word WARNING or this symbol indicate practices that are unsafe or dangerous and could result in serious injury to the occupant and or caregiver WARNING READ INSTRUCTION MANUAL Choose The Right Chair amp Safety Options In the mobility industry there are several options available to meet the needs of children Make sure that your and your provider s choice of chair and other options takes into account your child s comfort positioning physical limitations and hazards that may be encountered during daily use PAY Page 8 REACH User Manual Warnings Failure to Follow These Warnings Could Result in Serious Injury or Death WARNING All caregivers and or attendants must read this user manual prior to operating the Reach chair Familiarize yourse
7. age 12 REACH 4 2 Handlebar Angle Adjustment 1 Press and hold buttons on outside of each adjustment ratchet reference Figure 5 2 Adjust handlebar to desired angle 3 Release buttons 4 3 Knee Angle Adjustment 1 Press and hold buttons on outside of each adjustment ratchet reference Figure 6 2 Adjust knees to desired angle 3 Release buttons 4 4 Seat Tilt Angle Adjusment 1 Engage Wheel Locks 2 Remove bolt and nut from left and right sides reference Figure 7 5mm hex wrench and 13mm wrench required 3 Adjust seat to desired angle reference Figure 8 4 Install bolts and nuts tighten Do not over torque this could result in damage to the seat tube 5 Adjust hip angle to desired angle reference section 4 5 Nut Page 13 User Manual Se Figure 8 REACH User Manual 4 5 Hip Angle Adjustment 1 Engage wheel locks 2 Place one hand on handlebar 3 Rotate handle in either direction to unlock hip angle 4 Adjust to despired position 5 Release handle to lock into position 6 To verify hip angle is locked check alignment of handle assembly Linkages should be parallel to tube as shown in Figure 9 MAI Locked Unlocked 4 6 Folding amp Unfolding Folding 1 Engage wheel locks 2 If chair has 20 or 30 seat angle adjust hip angle to furthest forward postion 3 If chair has 10 seat angle adjust hip angle one position back
8. bolts 2 4mm hex wrench required 2 Adjust to desired angle 3 Reinstall bolts 4 11 Positioning Tray 1 To insert tray swing left and right tray cam locks downward Reference Figure 28 2 Slide Tray into receivers and adjust to desired depth 3 Swing left and right tray cams upward to lock in place Reference Figure 29 Page 19 REACH User Manual 4 12 Using The Reach Chair As A Seat In A Motor Vehicle The Reach Chair is approved for transporting children in motor vehicles when it is equipped with the OPTIONAL transit feature and used in accordance with these instructions The chair must be secured in a forward facing position with a Wheelchair Tie down and Occupant Restraint System WTORS which meets the requirements of SAE J2249 Recommended Practice Wheelchair Tie down and Occupant Restraint Systems For Use in Motor Vehicles IMPORTANT INFORMATION This chair conforms to and has been dynamically tested in compliance with ANSI RESNA WC Vol 1 Section 19 5 3 Please contact Leggero or your authorized Leggero provider if you have any questions regarding use of the chair for seating in a motor vehicle Contact information can be found on page 2 of this manual WARNINGS amp INSTRUCTIONS The Reach chair must be used as indicated in these instructions and the instructions supplied by the vehicle mounted tie down manufacturer Chair occupant should be transferred to the vehicle seat and use the vehicle restraint s
9. cushions straps User Manual Figure 20 E S CC Pro ei y fj S Figure 21 Single Knob 12 Chair G AN AN Es 287 Figure 22 2 knobs 14 amp 16 Chair A Page 17 REACH 4 9 Seat Depth Adjustment Cont For 12 and 14 chairs it may be necessary to remove the seat adjustment plate to extend seat depth to desired position With 12 chairs the plate will need to be removed to achieve 11 13 seat depths With 14 chairs the plate will need to be removed to achieve 14 16 seat depths 1 Remove seat cushion 2 Remove front bolts 1 using 4mm hex wrench and 10mm wrench 3 Remove seat depth adjustment bolts 2 and knobs 4 Remove seat plate assembly from chair 5 Remove seat depth adjustment plate 3 from seat plate using 4mm hex wrench and 10mm wrench 6 Reinstall seat plate as shown in Figure 24 7 Reinstall front bolts seat depth adjustment bolts and knobs 8 Adjust seat to desired depth 9 Reinstall seat cushion W7 Page 18 User Manual Ma LS SS AE 5 Y SPSS Figure 25 o SNS AE CES Y IAN REACH User Manual 4 10 Armrest Adjustment To Adjust Height 1 Remove button head bolts 4 4mm hex wrench required Reference Figure 26 2 Adjust to desired height 3 Reinstall bolts To Adjust Angle 1 Remove rear button head
10. d assembly downward on the footrest extensions 12 amp 14 chairs only 1 Remove bolts as described in previous section 2 Remove footbed assembly from chair 3 Remove flat head and button head bolts from left and right sides reference Figure 16 5mm Hex wrench required 4 Reinstall bolts in lowest position on footbed extensions as shown in Figure 1f 5 Reinstall footbed assembly and adjust to desired height For 12 units it will be necessary to change the footbed extensions to obtain leg drops beyond 11in 28cm Longer extensions were supplied with your chair but if you do not have them please contact your authorized provider 1 Remove bolts as described in previous section Reference Figure 18 2 Install longer extensions as shown in Figure 19 For the next leg drop position beyond what was achievable with shorter extensions install flat head bolts through 7th hole from top of footbed extensions 3 Install footbed assembly in chair and adjust to desired height Long Extensions 4 1 Leggero Xy Page 16 REACH 4 8 Back Height Adjustment 1 Loosen bolts at locations shown in Figure 20 5mm hex wrench required 2 Adjust back to desired height 3 Tighten bolts 4 9 Seat Depth Adjustment 1 Loosen seat cushion straps 2 Loosen knob s under seat plate Reference Figure 21 or 22 3 Adjust front seat assembly to desired depth 4 Tighten knob 5 Tighten seat
11. e chair WARNING When folding the chair be aware that there is a risk of injury through fingers becoming crushed or trapped Reference section 4 6 of this manual for further information WARNING Straps from chest harnesses or lap belts can become trapped in the folding lock bracket Please trim all straps as shortly as possible Always ensure that frame is locked into upright position prior to resuming use When unfolding you will hear a click when the frame locks WARNING The chair is only intended to carry one child at a time Do not carry more than one child at a time WARNING Only lift the chair by parts that are solidly attached The chair should be lifted by the side frame members whenever possible If folded hold the chair by the lower side frame tubes Always use two people for lifting to prevent injury and damage to the chair WARNING Please keep packaging material away from children Discard all plastic packaging material immediately after unpacking WARNING If your chair is not equipped with the transit option do not use it as a seat in a motor vehicle Transfer the child from the chair to an approved motor vehicle seat If your chair is equipped with the transit option refer to the section 4 12 in this manual WARNING The chair must be inspected and maintained per the chart in Section 6 Maintenance Problems detected must be repaired prior to resuming use of the chair WARNING Many of the fasteners used to cons
12. from furthest forward GAS IN As Folding Handle 4 Place one hand on handlebar with other hand pull Zi Folding Handle I ama a Y folding handle upward Reference Figure 11 Push forward on handlebar and chair will fold Adjust handlebar inward Flip footbed upward Adjust knee angle as far inward as possible CON OO Unfolding 1 Adjust handlebar outward 2 Flip Footbed down 3 Swing knee ratchets outward 4 Pull back on handlebar until locking mechanism locks PA Figure 12 Leggero W7 Page 14 REACH User Manual Adjust Hip Angle Forward Pull Handle amp Fold Adjust Handlebar In Flip Up Footplate amp Adjust Knees In WARNING When folding or unfolding keep arms hands and feet clear of moving components to avoid injury Reference Figure 13 arrows indicate potential pinch points WARNING Straps from chest harnesses or lap belts can become trapped in the folding lock bracket Please trim all straps as shortly as possible amp attach lap belt buckles prior to folding Straps Here Can Prevent Frame from Locking 4 7 Footbed Height Adjustment 1 Remove left and right button head bolts reference Figure 14 5mm hex wrench required 2 Adjust footrest assembly to desired height 3 Reinstall bolts Figure 14 Page 15 REACH User Manual 4 7 Footbed Height Adjustment Cont If your footbed is currently configured as shown in Figure 14 it may be necessary to adjust the footbe
13. intenance is not performed at the specified intervals Please see table below for recomended maintenance procedures and frequency There is a maintenance record on the following page of this manual that should be used to document maintenance activities Maintenance Activity Weekly Monthly Check wheels and tires for wear or damage Check wheel lock function Check for proper caster alignment Verify that all fasteners are tight 7 Verify that quick release axles function properly Check tilt lock mechanism for proper engagement Check recline lock mechanism for proper engagement Check all structural components for wear or damage Check all accessory components for damage We recommend that the chair be cleaned regularly Clean all frame components and plastic parts using mild detergents only Fabric parts may be washed If using a washing machine put them in a linen bag or pillow case Air dry In most cases wiping with a damp cloth is sufficient Do not use your chair in salt water as severe damage may result Keep sand or other particles from damaging the wheel and caster fork bearings ria Leggero Ww Page 22 REACH User Manual Maintenance Record Service Provider Technician Description of Service Page 23 V7
14. lf with handling and functions of the product prior to actual use If there is any information in this manual that you do not understand please contact your authorized Leggero provider for assistance WARNING Non conventional use and or handling of the product can be dangerous The pushchair is not safely suitable for skating or similar high speed activities Swiveling front wheels can wobble at higher speed and can cause a sudden stop and tip over of the chair For maximum safety use the pushchair only at regular walking speed Under no circumstance should you let go of the handlebar while pushing Do not ever push the chair away WARNING The initial set up of this pushchair must be performed by a qualified technician WARNING Procedures other than those described in this manual must be performed by a qualified technician WARNING The weight carried by the Reach chair must not exceed the total weight limit of 80lb 36kg for 12 chairs 110lb 50kg for 14 chairs or 150lb 68kg for 16 chairs Maximum occupant weight plus weight of accessories and or items carried WARNING Adjustments made to the chair may affect stability increasing the risk of tipping Adjustments must be made by your authorized Leggero provider WARNING Avoid getting the chair wet or storing the chair in damp environments Excess moisture can cause rust or corrosion which can result in component failure If the chair is exposed to moisture dry thoroughly WARNING
15. truct the Reach chair consist of a bolt with a nut that contains a nylon lock ring These connections must be maintained and secured with the original equipment fasteners and properly adjusted For proper adjustment of pivot points consult your authorized service provider LAS Leggero Ns Page 10 REACH User Manual Section 3 Unpacking the Reach Chair 1 Remove chair from packaging 2 Discard all plastic packaging materials 3 Unfold frame and seat back reference Section 4 6 of this manual 4 Install rear wheels reference Figure 1 5 Check for proper adjustment of quick release axles by pulling outward on wheel Wheel should hold in place 6 Engage wheel locks reference section 4 1 of this manual 7 Install anti tips reference Figure 2 WARNING Please keep packaging material away from children Discard all plastic packaging material immediately after unpacking VS V 4 135 SK ei WS Figure 2 Page 11 W7 REACH User Manual Section 4 Operation and Adjustment Tools Required 4mm Hex Wrench 5mm Hex Wrench 4 1 Wheel Lock Operation 1 To engage wheel locks push crossbar down with foot Reference Figure 3 2 Verify wheel locks are engaged on each side by trying to move chair front to back 3 To disengage wheel locks pull crossbar up with foot Reference Figure 4 Push DownTo Engage Wheel SA TES f IS LE 4 SK A AS a 7 II AA EA SEN TR Figure 4 P
16. y applies in the USA only Check with your supplier if international warranties apply E WHAT MANUFACTURER WILL DO Our sole liability is to repair or replace covered parts This is the exclusive remedy for consequential damages F WHAT YOU MUST DO 1 Obtain from us while this warranty is in effect prior approval for return or repair of covered parts 2 Return the product or part s freight pre paid to Leggero LLC Contact Leggero customer service at 1 844 503 KIDS for a return address and to obtain a return authorization number RAF 3 Pay the cost of labor to repair remove or install parts G NOTICE TO CONSUMER 1 If allowed by law this warranty is in place of any other warranty written or oral express or implied including a warranty of merchantability or fitness for a particular purpose 2 This warranty gives you certain legal rights You may also have other rights that vary from state to state Page 21 WT REACH User Manual Section 6 Maintenance Please consult your authorized provider if you have questions regarding maintenance of your Reach chair Consistent and thorough maintenance will extend the useful life of your chair Improper maintenance can significantly decrease the useful life of the chair Any damaged parts should be replaced prior to resuming use of the chair The chair should be cleaned regularly and should be serviced by an authorized dealer at least once per year Warranty might be affected if proper ma
17. ystem whenever possible Do not exceed maximum occupant weight ratings Reference Section 1 8 of this manual The Reach Chair must be placed in a forward facing position when used as a seat in a motor vehicle Use an approved 4 point strap type tie down system for the chair Use an approved 3 point belt for occupants over 50lb 23kg For occupants under 50lb 23kg a 5 point transit harness is required For approved transit tie down locations and location of belt harness attachment pin see Figures 30 and 31 Restraints must not be held away from the child s body by chair components or accessories Belt or harness straps should be adjusted until they are snug and do not have slack If you can pinch the webbing of the belt straps between your fingers then it is too loose Only belt restraints that comply with the provisions of ANSI RESNA WC Vol 1 Section 19 4 9 2 4 9 5 and 5 2 that have been dynamically tested in accordance with Annex A amp 5 3 of the same should be used on the chair for use as a restraint in a motor vehicle Figure 30 WARNING If your chair is not equipped with the transit option do not use it as a seat in a motor vehicle Transfer the child from the chair to an approved motor vehicle seat i Page 20 REACH User Manual Section 5 Limited Warranty A THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL PURCHASER OF OUR PRODUCTS B FOR LIFETIME Leggero LLC warrants the frame and quick release
Download Pdf Manuals
Related Search