GiantAlarm System Co.,Ltd Swing Gate Opener JJ-PKM
Contents
1. JUJIANG Giant Alarm System Co Ltd Swing Gate Opener JJ PKM C01 User Manual NEw JUJIANG Website http www giantautogate com http jujiang en alibaba com CAUTION This product must be installed by well trained skilled professionals in compliance with the regulations concerning the field swing gates opener device Unqualified personnels or those who do not know the standards applicable in this field should not carry out the installation under any circumstances Every time must cut off power supply before starting installation operation or maintenance Please read the manual carefully before installation Incorrect installtion or misuse of product may cause seriously hurt on people or damage on other objectives If the supplied wires damaged or broken it must be replaced by the manufacturer its service agent or qualified persons in order to avoid any hazard Keep the wireless control system push button transmitters etc out of the reach of children Not allow children or other persons to stand near the motor while in operation Not allow to use transmitters to control the gate when it is out of sight Not allow to install the products at the place where is corrosive inflammable and explosive The manually released part of front motor can not be installed to the place where passerby could touch when gate closed Please keep this instruction for further reference 1 Product Description UPS F2. opening operation if no please exchange the wiring connections of 2 motors when the motor direction LED indicator is RED the motor should be in the closing operation If no please exchage the wiring connections Otherwise can not open and close the door normally
3. e actual usage LOCK12 Ternimal for Electric lock Swipe card to open two gates active low auto closing is enabled SWIPE CARD after the door opened 11 Terminal for photocells active low when the obstacle sensed by INFRARED photocell while the door is closing the door will stop and then rebound to open Common terminal for connecting ground 12 28V output voltage supply the power for photocells or other saftey devices current lt 200mA 6 Motor running speed Soft start when open and close the door 700ms later then switch to high speed running Time adjusting 0 33 seconds high speed time can be adjusted by HSPEED TIME trimmer When high speed running time ends it switches into low speed running till the motor stops running When the motor stops in the halfway for the first time during it runs from open limit position or close limit position then high speed running time will adjust automatically based on previous running time 7 High speed running time adjustment Adjusting 0 30s high speed running time through HSPEED TIME trimmer When the trimmer turns to the minimum it s Os the high speed running disabled the motor keeps running in low speed Only when both motors working then high speed running timing enabled 8 Limit amp obstacle sensitivity adjustment During the opening and closing the motor stops running once the limit amp obstacle sensitivity signals sensed Sensitivity of the two mot
4. e panel If there is no any signals received within 5seconds the LED will light and then exit code learning state 4 Code removing press and hold learning button once you press learning button LED is off 5seconds later LED lights up now the codes has been removed 5 Instructions for all terminals This terminal is same as single leaf button of transmitter 2 SIDE It controls the door as Open Stop Close Stop Open cyclically This terminal is same as double leaf button of transmitter ISIDE It controls the door as Open Stop Close Stop Open cyclically Common terminal for connecting ground Wiring of motorl should connect wires of the motor which opens MOTO I first Or connecting the wires of motor installed at the side of door with thrust plate Wiring of motor2 should connect wires of the motor which you MOTOI DELAY could use single leaf button to control supply AC 12V 2 switch high speed running to low speed running Supply DC 12V Motor only runs in low speed Need to 24V 12V 12V 0V 0V 12V adjust HSPEED TIME trimmer to the minimum position Supply DC 24V amp 12V together switch high speed running to low speed running External 12V storage battery the storage battery can be charged When there is no power supply the UPS will start working UPS automatically The standby current of UPS when it is working is 20mA the current 1s around 1 5A when the motor is running specific current depends on th
5. echnical Parameters 1 Control Panel Voltage AC DC 12V 24V 2 Motor s Voltage 12VDC 24VDC 3 Encoder For transmitter Our own customed rolling code 4 Support remote control Can memorize 20PCS transmitters at most 5 Range of application Suit for all double arms swing gate opener JUJIANG 2 Wiring diagram for control panel Hish speed delay time auto closing Motol amp 2 run time Setting of open sensitivity adjustment adjusting or close door time J adjusting i H 11 mm MS 5 IU T D HOO JOA CIHVOWdIME Uda Vaan HZTHOOT ISI DE 2olDE un raf Bj t d San lSIDEZSIDE COM MOTO 12V OV 12V LED indicating motol amp direction 3 Functions and testing 1 Indicator LED light It s always on once the system electrified LED indicator for auto closing flashes every lsecond It turns off when enter into the learning code state or removing code state it flashes twice after successfully learning code or removing code 2 Transmitter using our company own customed rolling code Singe leaf button controls opening and closing of MOTOR2 double leaf button simultaneously controls opening and closing of MOTORI amp MOTOR2 The control panel can memorize 20 transmitters at most 3 Code learning press and hold learning button for 1second then release LED 10 turns off and press any button of transmitter then LED flashes twice now the codes has been learnt to th
6. ors are set seperately Adjusting the sensitivity of motorl through MOTORI trimmer while MOTOR2 trimmer control sensitivity of motor2 Notice Arm type motors only have the funcion of obstacle sensitivity no functions of limit 9 MOTORI amp 2 opening closing delay time adjustment When opening the door motor2 opens first then motorl opens later while closing the door motorl closes first then motor2 closes And opening closing delay time can be adjusted 0 30s 10 Auto closing time adjustment Auto closing funtion enabled when opening the door by swiping the card which should have card reader installed Auto closing time can be set for 0 second 5seconds and 10 seconds by using jumper The auto closing is disabled when you set 0 second No jumper connected means 0 second When jumper 1 connect with jumper 2 it means 10 seconds When jumper 2 connects with jumper 3 it means 5 seconds The LED indicator for auto closing time count down flashes every Isecond 11 Motor delay time protection As soon as the motor running continuously more than 60s the motor will automaticlly stop working to protect the motor 12 Motor direction indentification When one side of door installed thrust plate or the contoller has function of setting order of opening amp closing or functions of swiping card make sure all the wiring connections of 2 motors are correct When the motor 1s running if motor direction LED indicator 1s blue now the motor should be in
7. ront bracket gt ge We NI Power cable Fig I 2 Swing Gate Opener Technical Parameters Input Voltage 24VDC 40W Rotational Speed 250RPM Rod s Running Speed 1 6cm s Rod s Max Travel 300mm Continue running time 5min Max Single leaf Length 2 5m 2 Travel Max Single leaf Weight 300KG Environment Temperature 20 C 50 C Protection Calss IP55 3 Spec Size 2pcs lpcs Spcs Spcs Fig 3 5 Installation Description 5 1 Required tools for installation Fig 4 5 2 Installation diagram B A 27 5 H ra zl 3 T D Swing gate motors A rwssalibe 3 Control Pane 4 Alarmlamp optional 5 Photocell optional Ground block Ground block Installation diagram Fig 6 5 3 Installation size you can adjustment the gate degree according to these numbers Fig 7 connect front bracket Fig 8 Different connecting method for front and rear bracket Using different installation method according to different material and environment for front bracket PEM 4 pcs Connection for rear bracket and motor Make the hole down Make the power cable down The height difference for installing the front and rear bracket 25mm L 700mm 5mm k 700mm 3 1 5mm Am Release by spanner then lift vit OM 3 Manually spanner Manual for Control Panel 1 T
Download Pdf Manuals
Related Search