PELLET STOVES USER MANUAL - La Nordica
Contents
1. FUMES The flue gas temperature has OVERTEMP AL exceeded 310 C Th m ion chamber or burn pot e COmDUSIO PO Make sure the holes at the burn pot bottom are completely free CLEAN CHECK UP 1 2 Pottom are dirty Check cleanliness of the fumes pipe and the combustion chamber The door is not closed correctly The ash pan is not closed correctl ii oo P y Check hermetic closure of the ash drawer Th ression sensor is faulty DES a y Other restoration operations must be carried out by an authorised The flue exhaust pipe is blocked alan Incorrect installation 1 IN BURNING PHASE 2 IN OPERANT PHASE DEPRESSION ALARM i Check for the presence of pellets in the feed box The pellet feed box is empty i Lei Adjust the pellet flow see Pellet feed adjustment NO Pellet feed calibration inadequate PE IGNITION eel do Check the procedures described in the Ignition chapter Other restoration operations must be carried out by an authorised technician Switch the stove to OFF using key 1 and repeat the procedure described in the Ignition chapter Other restoration operations must be carried out by an authorised technician In the work phase the t of the flue ui pellets in the feed box di P PEE Oy Other restoration operations must be carried out by an authorised os technician Every time the stove displays one of the alarms listed above it will switch off automatically The stove will block2. THE GENERATOR MUST NOT BE USED BY PERSONS INCLUDING CHILDREN WITH REDUCED PHYSICAL SENSORY AND MENTAL CAPACITIES OR WHO ARE UNSKILLED PERSONS UNLESS THEY ARE SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY CHILDREN MUST BE CHECKED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR WHEN PARTS OF THE BODY ARE WET OR DAMP THE SAFETY AND ADJUSTMENT DEVICES MUST NOT BE MODIFIED WITHOUT THE AUTHORISATION OR INDICATIONS OF THE MANUFACTURER DO NOT PULL DISCONNECT TWIST ELECTRIC CABLES LEAVING THE STOVE EVEN IF DISCONNECTED FROM THE ELECTRIC POWER SUPPLY MAINS IT IS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT DOES NOT COME INTO CONTACT WITH HOT PARTS OF THE APPLIANCE THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER INSTALLATION DO NOT CLOSE OR REDUCE THE DIMENSIONS OF THE AIRING VENTS IN THE PLACE OF INSTALLATION THE AIRING VENTS ARE ESSENTIAL FOR CORRECT COMBUSTION DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF CHILDREN OR UNASSISTED DISABLED PERSONS THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL FUNCTIONING OF THE PRODUCT WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH ESPECIALLY ALL EXTERNAL SURFACES ATTENTION MUST BE PAID e CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOLLOWING A PROLONGED PERIOD OF INACTIVITY THE GENERATOR HAS BEEN DESIGNED TO
3. SWITCH OFF Press key 1 for three seconds when the operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets The fumes motor and the hot air ventilation motor will remain on until the temperature of the stove has dropped below the factory parameters RE IGNITION The stove can only be re ignited if the flue gas temperature has lowered and the preset timer has been reset to zero BURN POT BOTTOM CLEAN CHECK UP 1 2 SHOULD THE CLEAN CHECK UP ALARM BE TRIGGERED MAKE SURE THAT THE BOTTOM OF THE BURN POT IS FREE OF RESIDUES OR SCALES THE HOLES AT THE BOTTOM MUST BE COMPLETELY FREE TO GUARANTEE a CORRECT COMBUSTION THE ABOVE INDICATED PELLET FEED REGULATION FUNCTION CAN BE USED TO ADJUST COMBUSTION BASED ON THE DESCRIBED REQUIREMENTS IF THE ALARM PERSISTS AND THE ABOVE LISTED CONDITIONS HAVE BEEN CHECKED CONTACT THE QUALIFIED AFTER SALES ASSISTANCE CENTRE ENGLISH LE OExtraflame USER MENU PELLET FEED ADJUSTMENT The following menu allows the pellet feed percentage to be adjusted If the stove has functioning problems due to the quantity of pellets adjust pellet feeding directly from the control panel The problems related to the amount of fuel can be divided into 2 categories NO FUEL the stove can never develop a suitable flame tending
4. ON when the stove reaches the set room temperature and exceeds it by 2 C it will switch off after a default delay time displaying STAND BY When the room temperature is 2 C lower than the setting the stove will start to work again at the power set on the display displaying OPERANT STBY FUNCTION SET AT OFF DEFAULT SETTING If the stby function is not active OFF if the stove reaches the set room temperature it will go to minimum modulating and displaying MODULATION When the room temperature is below the setting it will start to work again at the set power displaying OPERANT CONTROLS PROCEDURE press key 5 for a few seconds until SET CLOCK appears Press key 3 until USER appears Press key 5 twice Use key 2 or 3 ON to activate or OFF to de activaate 4 Press key 1 several times to confirm and exit the menu 14 ENGLISH OExtraflame RESET Allows all values that can be modified by the user to be reset to the default values The modified data is the following CONTROLS PROCEDURE Press key 5 until SET CLOCK appears Press key 3 several times until USER appears Press key 5 Press key 5 until RESET appears Use keys 2 3 to select ON and press key 5 DONE will appear on the display to confirm COMFORT incertain models This mode reduces the fan speed making the stove quieter CONTROLS PROCEDURE To activate press key 4 until COMFORT ON appears on the disp
5. FUNCTION IN ANY CLIMATIC CONDITION IN PARTICULARLY ADVERSE CONDITIONS STRONG WIND FREEZING SAFETY SYSTEMS MAY INTERVENE THAT SWITCH THE GENERATOR OFF IF THIS OCCURS CONTACT THE TECHNICAL AFTER SALES SERVICE AND ALWAYS DISABLE THE SAFETY SYSTEMS IN THE EVENT THE FLUE CATCHES FIRE USE SUITABLE SYSTEMS FOR SUFFOCATING THE FLAMES OR REQUEST HELP FROM THE FIRE BRIGADE THIS APPLIANCE MUST NOT BE USED TO BURN WASTE DO NOT USE ANY FLAMMABLE LIQUIDS FOR IGNITION DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO INTO CONTACT WITH THE PRODUCT THE MAJOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND AS SUCH CAN HAVE MICRO DOTS CRACKLES AND CHROMATIC IMPERFECTIONS THESE FEATURES HIGHLIGHT THEIR VALUABLE NATURE DUE TO THEIR DIFFERENT DILATION COEFFICIENT THEY PRODUCE CRACKLING WHICH DEMONSTRATE THEIR EFFECTIVE AUTHENTICITY TO CLEAN THE MAJOLICAS IT IS RECOMMENDED TO USE A SOFT DRY CLOTH IF A DETERGENT OR LIQUID IS USED THE LATTER COULD PENETRATE INSIDE THE CRACKLES HIGHLIGHTING THEM ROUTINE MAINTENANCE Based on Decree 22 January 2008 n 37 art 2 routine maintenance means interventions aimed at reducing degradation due to normal use as well as dealing with accidental events entailing the need of first interventions which however do not modify the structure of the system upon which one is intervening or its intended use according to the requirements laid down by the technical standards in force and by the manufacturer s use and
6. PSI One must also bear in mind all laws and national regional provincial and town council regulations in force in the country in which the appliance has been installed as well as the instructions contained in this manual ee ee ue ne neuer gy Xs AX CONNECTION TO THE MAINS ELECTRIC SUPPLY The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket possibly with a circuit breaker switch The socket must be easily accessible The electrical system must be compliant with standards The efficiency of the earthing circuit must be checked Unsuitable earthing of the system can cause malfunctioning for which the manufacturer will not be held liable Power supply variations beyond 10 can cause faulty operation of the product 6 ENGLISH OExtraflame HOT AIR DUCTING The pipe destined for ducting the hot air must have an internal diameter of 80 mm be insulated and protected from heat loss The length must not exceed 6 metres Installation of the pipes used for ducting the hot air must be performed by qualified staff and or the manufacturer s technical after sales assistance GIUSY PLUS VIVIANA PLUS The ducting extension is found in the accessory pack inside the stove It is mounted by means of the 4 supplied screws FOR THIS P
7. any release attempt during this phase showing the alarm itself and STAND BY alternately on the display The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have passed from displaying the same alarm The mechanical depression sensor Contact after sales centre has tripped BLACK OUT NO IGN No power during the ignition phase Attempt to release the alarm with stove still in cooling mode COOLING STAND BY DAMAGE DEPR SENSOR Component disconnected or faulty Contact after sales assistance COMMAND AUGER Abnormal functioning ALARM of pellet feeding Contact after sales assistance ENGLISH 25 QEXxtraflame GUARANTEE TERMS 1 Extraflame S p A products are guaranteed within the European community for 24 months from the date of purchase Purchase has to be proved by means of a valid fiscal document issued by the seller receipt invoice or shipment document identifying the purchased product and its purchase and or delivery date WARNING This conventional guarantee does not replace the guarantee regulated by the European legislation on consumer rights The conventional guarantee is only applicable to the Italian region and to those areas within the European Community where the Authorised Technical Assistance Centres are active see the www lanordica extraflame com website It is also limited to the state of residence of the consumer which must coinci
8. avoid coming into contact with these parts without wearing suitable protective clothing or using appropriate measures such as heat protective gloves DO NOT use the product with the door open or if the glass is broken The product must be electrically connected to a system equipped with an operational earthing system Turn off the product in the event of a failure or malfunctioning Unburned pellets that build up in the burner following each failed start up must be removed before attempting to start up the product again Make sure that the burner is clean and correctly positioned before starting it up again Do not wash the product with water Water may penetrate into the unit and cause faults in the electrical insulation This can cause electric shocks Installations not complying with the regulations in force as well as incorrect use and failure to comply with the maintenance scheduled by the manufacturer will invalidate the guarantee 9 ENGLISH 27 MExtraflame Riscaldamento a Pellet EXTRAFLAMES p A Via Dell Artigianato 12 36030 MONTECCHIO PRECALCINO VI ITALY EN 39 0445 865911 E 39 0445 865912 RK info extraflame it E www lanordica extraflame com The Manufacturer reserves the right to vary the features and data shown in this booklet at any time and without prior notice in order to improve its products This manual cannot be considered as a contract for third parties 29 05 2015 004276516 MANUALE UT
9. instructions may damage the surface of the generator and invalidate the warranty CLEANING THE CERAMIC GLASS Never use abrasive or chemically aggressive detergents for cleaning The cleaning of the ceramic glass is allowed only when the latter is completely cold To clean the ceramic glazing simply use a dry brush and some damp newspaper dabbed in the ash If the glazing is very dirty only use a specific ceramic glazing detergent Spray a modest amount onto a cloth and wipe the ceramic glazing Do not spray cleaner or any other liquid directly on the glass or on the gaskets Failure to observe the instructions may damage the surface of the ceramic glass and invalidate the warranty CLEANING THE TANK PELLETS When the tank empties completely unplug the power cord from the generator and remove residues dust chips etc from the tank empty before filling it DAILY SCRAPERS Use the scrapers moving upwards for models with upper scrapers or pulling and pushing them for the inserts and models with front scrapers Please note scrapers are preferably used when the stove is cold if used when the stove is hot it is recommended to use special gloves to protect against the heat as they can get very hot ENGLISH OExtraflame Open the door Clean the glass with a damp cloth Never spray the detergent or any other liquid used for cleaning directly on the ceramic glass CLEANING THE BURN POT AND COMBUSTION CH
10. iron grilles or coatings refractory materials e g Nordiker or others painted chrome plated or golden parts majolica ware handles the brazier and its related components For Idro products the heat exchanger is not covered by the guarantee if a suitable condensation proof circuit is not set up to ensure a return temperature of the device of at least 55 C The guarantee excludes all the external components on which the consumer can directly operate during use and or maintenance or that can be subject to wear and or rust and stains on steel due to aggressive detergents If malfunctions are signalled which are not later confirmed during check by an authorised technician the cost of the intervention will be borne entirely by the consumer 3 If it is not possible to restore product conformity by repairing it the product component will be replaced the guarantee expiration date and conditions will remain the same established when the product component to be replaced has been purchased 4 Extraflame S p A cannot be held liable for injury or damage which may either directly or indirectly be caused to persons animals and property ensuing from failure to observe all the instructions provided in the relevant instruction manual and the warnings regarding installation use and maintenance of the product that can also be downloaded on the website 5 Interventions for adjusting and or regulating the product for the type of fuel or other reasons are exc
11. maintenance manual 4 ENGLISH OExtraflame INSTALLATION GENERAL The flue gas exhaust and hydraulic connections must be carried out by qualified personnel who must issue installation conformity documentation compliant with national standards The installer must provide the owner or person acting for him according to the legislation in force with the declaration of conformity supplied with 1 the use and maintenance manual of the appliance and of the system components such as for example the smoke ducts chimney etc 2 photocopy or photograph of the chimney plaque 3 system booklet where applicable The installer must ask to be issued with a receipt stating that the documentation has been provided and must keep it with a copy of the technical documentation relating to the installation For installation in a condominium prior approval from the condominium s administrator must be requested COMPATIBILITY Installation in premises with fire hazards is forbidden Installation in residential premises except for sealed operation appliances is also forbidden in which there are liquid fuel operated appliances with continuous or intermittent operation which draw the combustion air in the room in which they are installed or in which there are type B gas appliances intended for room heating with or without production of domestic hot water and in adjacent and adjoining premises or in which in any case the depression mea
12. the fantastic sensation that the heat of a flame gives in complete safety WARNINGS This instructions manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to another owner or user or if transferred to another place If it is damaged or lost request another copy from the area technician This product is intended for the use for which it has been expressly designed The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use Installation must be performed by qualified staff which assumes complete responsibility for the definitive installation and consequent good functioning of the product installed One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed as well as the instructions contained in this manual The Manufacturer cannot be held responsible for the failure to comply with such precautions After removing the packaging ensure that the content is intact and complete Otherwise contact the dealer where the appliance was purchased All electric components that make up the product must be replaced with original spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning SAFETY
13. to remain very low even at high power at minimum power the stove tends to almost switch off bringing the stove to the NO PELLET alarm condition when the stove displays the NO PELLET alarm there may be non burned pellets inside the burn pot EXCESS FUEL the stove develops a very high flame even at low power the panoramic glass is very dirty obscuring it almost totally the burn pot tends to become encrusted blocking the holes for air intake due to the excessive pellet feed as it is only partially burned The adjustment to be performed is in percentage Therefore changing this parameter will lead to a proportional variation of all stove feeding speeds Feeding is from 30 to 20 Follow the procedure on the display to perform the procedure CONTROLS PROCEDURE press key 5 for a few seconds until SET CLOCK appears Press key 3 several times to reach SET USER Confirm using key 5 Pellet is displayed Using key 2 and 3 it is possible to increase 3 or decrease 2 feeding during the OPERANT phase Press key 1 several times to confirm and exit the menu STAND BY The STBY function is used if immediate stove switch off is required when the set temperature has been reached The STBY function can be set at ON or OFF using the procedure described further on In the factory the STBY function is always set at OFF indicator off STBY FUNCTION SET AT ON If the STBY function is active
14. AMBER 1 Vacuum the residues in the burn pot 2 Take out the burn pot from the designated compartment 3 Vacuum the ash from the burn pot s seat and the combustion chamber 3 1 4 Use the special poker supplied to clear the holes in the burn pot 5 Place back the burn pot and push it towards the hearth wall 6 If there is an ash collector tray vacuum the ash deposits PLEASE NOTE USE A SUITABLE VACUUM CLEANER WITH A SPECIAL CONTAINER TO SEPARATE THE COLLECTED ASH P 7 i 5 7 eras FT i F i gi j z 7 a i 7 k ee a ea Roi Li r Mei 5 ANO 4 Meet he A O la j Mao muli s i 4 Ta Mae el i Wi Y ii 17 A 7 e j sini Lh e a e ee hrs lr 2 ip ee i RS Mi 7 d Y ETT A E i Di Jol j 0 Le pr 7 LI i K ENGLISH OExtraflame EVERY 3 4 DAYS WEEKLY ASH DRAWER Every 3 4 days check the ash drawer and empty it at least one twice a week If there is a lower door open remove it Take out the removable ash drawer and empty it in a special container Vacuum the area underneath the removable ash drawer Once you have cleaned it place back the removable drawer and close place back the external door In some stoves the ash collector tray is located in the combustion chamber In this case just open the door and vacuum the ash from the tray pui fr j ai a a i FE A e gt Ka ant MEA tA A pri ME yo e a y all E por MONTHLY CLEANING
15. PI SIG TIN DAY MONTRAND Yaseen sect oia 12 ADIOS TINO LANA oa 12 FUNCTIONING AND LOGIC siscascsscssnsinssiceawstnsgtonseionedecenscduscseneiesdcuetesusensenssostasnustenssethesssscebusesetessecsusseucuuseeussdossenkeisdoverenbece stunnte 13 MIS ER MEN RR santosebereunnessnscas counussnavusausseseceutedidovansesistesneept 14 PELUET FEED ADJUSIMENT isos don E dii 14 AAND EY A N o A II cetacean cast aed 14 PP o AE E A E RO O II N nee eee cea ean tea eceedeees eects 15 CONOR acciai 15 ENABLE CHRONO AZ PP RO 15 CMRONO iii ra 15 PROGRAMMINGEXNPLE alari cda alii 16 CLEANING AND MAINTENANCE siccsssvcvesscsesassscssecesussdevcescssdederavesobcossuossdadinsousectesseeuaovenaevessadecuassuseivcvenalecdesuslsuecacesonceuviateussess 17 MAINTENANCE circa ir E NR AA 17 CLEANINGAND MAINTENANCE BY THE USER anios ivi 17 ROUTINE MAINTENANCE CARRIED OUT BY AUTHORISED TECHNICIANS sesssssseecccccssssssescccosoooosescecososoosescccecossosssseseses 21 PUTTING THE EQUIPMENT OUT OF SERVICE END OF THE SEASON arl rire 21 DISPLAY A 24 ALARMS E A A TEATRI TR 25 GUARANTEE TERMS lt cssscccscencsnisesaeutavctenscnteesssuitssdaavoesiovsesucsoacebacdaanloasdoacentoysssusdesdesdessbeudeseduedshseussusbeodiuasesteuscnunicedeeieoscensedieusases 26 ENGLISH 3 OExtraflame We thank you for having chosen our company our product is a great heating solution developed from the most advanced technology with top quality machining and modern design aimed at making you enjoy
16. Qextraflame Riscaldamento a Pellet PELLET STOVES USER MANUAL DORINA GIUSY GIUSY PLUS KETTY SERAFINA VIVIANA VIVIANA PLUS ENGLISH INGLESE OExtraflame 2 ENGLISH OExtraflame Lc UE imc ari 4 WARNINGS xcirrinr rara n ra Rien A AI 4 105 fe 4 ROUTINE MAINTENANCE ssssxsascicssscartasvccvsnsiaseseqansuseecnseneysesascusbannseceyennsneceaasnansnpavansdcauenbansesensscheansusupsesunaysncsaendensnsescsensexensaseersts 4 INSTALLATION RR ER 5 GENERAL cc 5 INIESTA CES lia 5 COMBUSTION A CONNECS HON sana iii 6 MNOTAIRDUCTIN Gina siria NENTI TAI TANITI SCONTRA TSI ZA SECC TCNTNTI TRITATA STIA TA TTI RI CESTI 7 ADDITIONAL THERMOSTAT FUNCTIONING FOR DUCTING MOTORCONTROL r aa 7 PELLETS AND FEEDING A ARO 8 THE DISPLAY DESCRIPTION OF CONTROLS AND SYMBOLS ccccccccccccscscccccccccccccccccccccccssccccsccccccccccssscescssccccccscsscsosees 9 Se INS da APA E O nn o E eee 9 MENO STRUCTURE ias 10 BASIC INSTRUCTIONS iiistosiniincios dance dan cin dit indice 10 REMOTE CONTROL OPTIONAL i ccsssscesitsescontsestssessessstositessseasessessesuctancsdsossesusnasssecinsineausssactinnsesecsisabasseseuissieascestebssissassentbecsisess 11 PPE PND Pe TEU Or PU eS unan dolo 11 COMMISSIONING SET TIN GS sisuscccxssesssuessadsneccsessweusnapieursdensvsstinsaovecssxsevedusganstonsasbeseealenuseovsansbeussweuesavekesaeabausieveossessessannaqoxensens 11 MAINS FREQUENCY SOOO TAL sat ccna sats ott conc cesta en foe ae eae cased Snes ces Aes pias 11
17. RODUCT IT IS MANDATORY TO DUCT THE HOT AIR IT IS NOT POSSIBLE TO DEACTIVATE THE DUCTING MOTOR DO NOT COVER OR CLOSE DUCTING ADDITIONAL THERMOSTAT FUNCTIONING FOR DUCTING MOTOR CONTROL For models with ducting motor there is also the possibility of thermostatting the motor itself The connection of an external thermostat will allow to control the ducting motor independently from stove functioning At this point just set the desired temperature on the thermostat The thermostat will control the functioning of the second motor with temperature to be reached closed contact the second motor will follow the trend of the stove when the temperature has been reached open contact it takes the ducting motor to 1st speed and will be displayed by the flashing LED relative to the ducting motor The ducting thermostat clamp is fitted with jumper as per standard ENGLISH 7 OExtraflame PELLETS AND FEEDING Pellets are made by applying high pressure to sawdust or wood waste products not containing paint from sawmills carpentry and other activities related to processing and working with wood Given that it does not use any glue to hold it together this type of fuel is completely environmentally friendly In fact the compactness of the pellets over time is guaranteed by a natural substance found in the wood itself wood coal In addition to being an environmentally friendly fuel in that it push
18. S SERVICE OR BY A SIMILARLY QUALIFIED PERSON SO AS TO AVOID ALL RISKS The images are for illustration purposes Fumes motor disassembly and cleaning and fumes pipe new silicone in required points A B inspection of gaskets ash drawer and bum pot door replace them and apply silicone where required MD Tank tomplete empiyingand denin E Room iran disassembly and removal of dustand any pete SSCS TF Airitate pipe nspectonandaryfowsensordeanng SSS ENGLISH 21 OExtraflame The images are for illustration purposes 22 Fumes motor disassembly and cleaning and fumes pipe new silicone in required points Inspection of gaskets ash drawer and burn pot door replace them and apply silicone where required Combustion chamber total cleaning of the entire chamber and ignition plug tube cleaning Room air fan disassembly and removal of dust and any pellet debris Air intake pipe inspection and of flow sensor cleaning ENGLISH Z W Y va NJ AN Y LA ql A OExtraflame The images are for illustration purposes Fumes motor disassembly and cleaning and fumes pipe new silicone in required points Inspection of gaskets ash drawer and burn pot door replace them and apply silicone where required Y Combustion chamber total cleaning of the entire chamber and ignition plug tube cleaning O Tank complete emptyi
19. STUFE PELLET 596_001
20. THE HEAT EXCHANGER The heat exchangers chamber must be cleaned every month as the soot deposited on the rear of the hearth wall obstructs the regular flow of fumes thereby affecting the performance and regular operation of the stove Open the door to access the combustion chamber Take out the burn pot Remove or rotate depending on the model the upper lockbolt A the screws B or the wall lock C of the hearth wall D take out the hearth wall E and clean with the poker and a suitable vacuum cleaner F When cleaning has been completed reposition the removable hearth wall D and secure it again with the designated screws by turning the lockbolt in the opposite direction in relation to the one used to remove it or by placing back the hearth wall lock Place back the burn pot ENGLISH 19 OExtraflame TY JAN CLEANING THE LOWER SUMP IF THERE ISONE Some stove models have an inspection sump behind the ash drawer or underneath the combustion chamber In this case just open remove the clamping screws and vacuum the ash inside on applicable models 20 ENGLISH OExtraflame ROUTINE MAINTENANCE CARRIED OUT BY AUTHORISED TECHNICIANS Routine maintenance must be performed at least once a year As the generator uses pellets as solid fuel it needs an annual routine maintenance interval that needs to be performed by an authorised Technician by only using original spare parts Failure to do so can affect the a
21. adjust the hours minutes day month and year Press key 1 several times to confirm and exit the menu 9 SET CLOCK MON TUE WED SUN ADJUSTING LANGUAGE It is possible to select the preferred language to display the various messages CONTROLS PROCEDURE Press key 5 for a few seconds until SET CLOCK appears Press key 3 twice until SET LANGUAGE appears Confirm using key 5 Select the language using key 3 Press key 1 several times to confirm and exit the menu M LANGUAGE ss e SPANISH FAILURE TO IGNITE ALARM THE FIRST IGNITION MAY FAIL SINCE THE AUGER IS EMPTY AND CANNOT ALWAYS LOAD THE BURN POT INTIME WITH Cor THE NECESSARY QUANTITY OF PELLETS FOR REGULAR FLAME IGNITION IF THE PROBLEM OCCURS AFTER A FEW MONTHS OF OPERATION MAKE SURE THE ROUTINE CLEANING HAS BEEN PERFORMED CORRECTLY AS INSTRUCTED IN THE STOVE MANUAL 12 ENGLISH OExtraflame FUNCTIONING AND LOGIC IGNITION Once the points listed previously have been checked press key 1 for three seconds to ignite the stove 15 minutes are given for the ignition stage after ignition and once the control temperature has been reached the stove interrupts the ignition phase and switches to the STARTING mode STARTING During the start up stage the stove stabilises combustion increasing it gradually to then start ventilation and switch to the OPERANT mode OPERANT During the work stage the stov
22. cates weekly programming operation Off indicates the absence of alarms Indicator on weekly programming active Flashing indicates the deactivation of the depression 7 Indicator off weekly programming not active sensor i 5 a ba abs prea codi tele ee i indicates the stby function m e T read by the probe is over the set temperature Oif iby dente On the T read by the probe is below the set temperature On stby activated Ign plug Off ign plug active On ign plug deactivated Flashing ignition phase Not used it indicates the communication between remote control It indicates functioning of the fumes motor and stove Every time a key is pressed on the remote Off fumes motor not working control the indicator must switch on if the indicator is On fumes motor working always on it indicates that the communication between Flashing breakdown remote control and stove is blocked it indicates functioning of the tangential fan Off not working On working Not used Flashing The motor is operating in COMFORT momde where present Additional ducted thermostat input status On closed contact to be reached Flashing the motor is running at minimum in modulation Not used mode input open It indicates the operation of the pellet feed motor Off pellet feed motor deactivated On pellet feed motor active ENGLISH 9 OExtraflame MENU STRUCTURE Key 1 to confirm paramet
23. ck sub chapter have been followed so that the chrono function works Aside from programming it it must also be activated switch on time 22 00 INCORRECT Switch off time 05 00 ENGLISH 15 OExtraflame PROGRAMMING EXAMPLE Let s suppose that the weekly programmer function is to be used and the 2 time slots are to be used in the following way Ist time slot from 08 00 to 12 00 every day of the week with room temperature at 19 C excluding Saturday and Sunday 2nd time slot from 15 00 to 22 00 only on Saturday and Sunday with room temperature at 21 C 1ST TIME SLOT SWITCH OFF CONTROLS PROCEDURE SET Using keys 2 3 enter the time 12 00 STOP CLOCK which corresponds to the switch off time PRG1 Press key 5 and SET CLOCK will appear of the 1st time period The STOP PRG1 text Press key 2 until ENABLE CHRONO appears will appear followed by the time set Enable the chrono To confirm and continue programming Enable slot 1 and 2 ENABLE press button 5 Press button 4 to go back to Press key 1 to exit CHRONO the previous parameter ENABLING THE 1ST TIME SLOT DAYS Where ENABLE CHRONO is not present To do this use keys 3 and 5 in the following MONDAY in the menu enabling is done directly in way PRG1 SET CHRONO SET Key 5 allows to scroll the various days CHRONO the scrolling text with the day of the week followed by OFF Press key 2 and SET CHRONO will appear Use key 3 to enable disable ON OFF all day
24. de with the premises and or registered office of the seller of the Extraflame S p A product These regulations do not apply if the product is purchased within commercial entrepreneurial or professional circumstances In these cases the product guarantee will be limited to a period of 12 months from the date of purchase ITALIAN GUARANTEE What must be done if there is a product malfunction Consult the instructions manual to make sure the malfunction cannot be solved by using the product correctly Make sure the malfunction is included in those covered by the guarantee otherwise the cost of the intervention will be borne entirely by the consumer When requesting the intervention of the Assistance service at the Authorised Assistance Centre always specify type of malfunction model of the appliance complete address phone number EUROPEAN GUARANTEE What must be done if there is a product malfunction Consult the instructions manual to make sure the malfunction cannot be solved by using the product correctly Make sure the malfunction is included in those covered by the guarantee otherwise the cost of the intervention will be borne entirely by the consumer Request the intervention of the Assistance service or the address of the Authorised Technical Assistance Centre to the seller always specify type of malfunction model of the appliance complete address and phone number If the malfunction arises in the first 6 months of the product s li
25. e of air in the room during the cleaning of the product A poor cleaning is detrimental to the proper functioning and safety 9 o MAINTENANCE For correct operation the generator must undergo routine maintenance by a qualified technician at least once a year The routine checks and maintenance operations must always be performed by qualified trained technicians in accordance with the applicable regulations in force and with the instructions provided in this use and maintenance manual EVERY YEAR MAKE THE EXHAUST FUMES SMOKE DUCTS AND T FITTINGS INCLUDING CAPS AND INSPECTION DOORS BE CLEANED IF ANY CURVES AND ANY HORIZONTAL SECTIONS gt THE CLEANING OF THE GENERATOR FREQUENCY IS APPROXIMATE THEY DEPEND ON THE QUALITY OF THE PELLETS USED AND THE FREQUENCY OF USE IT CAN HAPPEN THAT THESE OPERATIONS SHOULD BE PERFORMED MORE FREQUENTLY CLEANING AND MAINTENANCE BY THE USER Routine cleaning operations as specified in this use and maintenance manual must be performed with the utmost care according to the instructions procedures and frequency intervals described in this use and maintenance manual CLEANING THE SURFACES AND COVERING Never use abrasive or chemically aggressive detergents for cleaning The surface cleaning must take place when both the generator and the coating are completely cold For the maintenance of surfaces and metal parts simply use a damp cloth with water or mild soap and water Failure to observe the
26. e reaches the set power and works to reach the set room temperature See following item SET THERMOSTAT ADJUSTMENT The room temperature setting can be set using buttons 4 and 5 from low 07 to 40 C hot LOW HOT if the temperature setting is on low set below the 7 C threshold the stove will always function at minimum If the setting is on hot set above the 40 C threshold the stove will not modulate always functioning and only at the set power SET POWER ADJUSTMENT The power setting features 5 operating levels via button 5 on 1 and 2 adjustment Power 1 minimum level Power 5 maximum level WORK WITH ROOM PROBE STANDARD The appliance controls the room temperature via a probe fitted on the appliance Once the the set temperature has been reached it will automatically go to minimum or switch off activating the Stand by function reducing pellet consumption to a minimum By default the STBY function is always set on OFF light MD on For its activation and logic follow the indications on the next page Chapter Stand by BURN POT CLEANING During the work stage the stove has an internal counter which cleans the burn pot after a set amount of time This stage will be shown on the display it will bring the stove to a lower power level and will increase the fumes motor for a programmed amount of time when the cleaning stage is finished the stove will continue its work going back to the selected power level
27. er programming and exit Keys 2 and 3 to set data parameters Keys 4 and 5 to go forward or backward in the menu To access the menu keep key 5 pressed for a few seconds O gt lt MES E as pe Jo 2 IT EN FR DE ES 23 MS K 273 Vea 273 w ENABLE CHRONO PROG 1 2 3 4 ON OFF I E 5 Ww i START PROG 1 2 MINUTES i CONFIRM STOP PROG 1 WITH KEY 1 2553 Ww MONTH MOND FRID 2 3 i y gt D START PROG 2 Ww Ww tL STOP PROG 2 23 MOND FRID 273 Where present certain models When ENABLE CHRONO is not included in the menu enabling is done directly in SET CHRONO BASIC INSTRUCTIONS The following recommendations must be followed the first times the stove is ignited Itis possible that slight odours are produced due to the drying of the paints and silicones used Do not remain in the environment for long periods Do not touch the surfaces as they could still be unstable Airthe room well several times Before igniting the stove the following points must be verified the feed box must be full of pellets the combustion chamber must be clean The burn pot must be completely free and clean check the hermetic closure of the fire door and the ash drawer make sure the power supply cable is connected correctly the bipolar switch in the rear right part must be positioned on 0 The hardening o
28. es wood residues to the limits pellets also have technical advantages While wood has a calorific value of 4 4kWh kg with 15 humidity after around 18 months of seasoning the calorific value of pellets is 5 kWh kg Pellet density is 650kg m3 and the water content is equal to 8 of its weight For this reason they do not require seasoning in order to arrive at a sufficiently adequate degree of heat yield The pellets used must comply with the characteristics described by the following standards EN PLUS UNI EN 14961 2 UNI EN ISO 17225 2 class A1 A2 The manufacturer always recommended using pellets with a diameter of 6 mm with its products PELLET STORAGE In order to ensure problem free combustion pellets must be stored in a dry place Open the tank lid and load the pellets using a scoop THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL WILL AFFECT THE FUNCTIONALITY OF YOUR gt GENERATOR AND MAY LEAD TO THE TERMINATION OF THE WARRANTY AND CESSATION OF ANY ACCOMPANYING RESPONSIBILITY ON THE PART OF THE MANUFACTURER 8 ENGLISH UExtraflame THE DISPLAY DESCRIPTION OF CONTROLS AND SYMBOLS ON OFF DISPLAY OF VARIOUS DISPLAY BUTTON TEXT MESSAGES OF POWER TEMPERATURE SETTING OPERATION POWER ADJUSTMENT DISPLAY ICONS KEY Indicates the presence of an alarm On indicates the presence of an alarm Y It indi
29. f the surfaces is terminated after several heating processes This appliance must not be used to burn waste DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE BOILING HOT STOVE DURING THE FILLING PHASE IN THE EVENT OF CONTINUOUS NO IGNITION CONTACT AN AUTHORISED TECHNICIAN gt IT IS FORBIDDEN TO USE THE APPLIANCE WITHOUT THE DIVIDER AND OR GLASS PROTECTION SEE FIGURE AT THE SITE JEOPARDISES THE SAFETY OF THE PRODUCT AND LEADS TO THE IMMEDIATE VOIDING OF THE WARRANTY PERIOD IN THE CASE OF WEAR OR DETERIORATION REQUEST AFTER SALES ASSISTANCE FOR REPLACEMENT OF THE PART REPLACEMENT THAT IS NOT UNDER GUARANTEE AS THE COMPONENT IS SUBJECT TO WEAR AO 10 ENGLISH OExtraflame REMOTE CONTROL OPTIONAL The heating power the desired room temperature and the appliance ignition switch off can be adjusted using the remote control To ignite the stove press key 1 for a few seconds the appliance will automatically enter the ignition phase It is possible to adjust power by using keys 4 and 5 whereas the desired temperature can be adjusted using keys 2 and 3 To switch the stove off press and hold key 1 fora few seconds TYPE AND REPLACEMENT OF BATTERIES The batteries are housed in the lower part of the remote control To replace it remove the battery holder as shown in the figure on the back of the remote control remove or insert the battery following the sy
30. fe the consumer has the right to have the product repaired with no expense From the seventh to the twenty fourth month if a malfunction arises the consumer will bear the cost of the call while the seller will pay for the manpower and for any spare parts used 2 If the malfunction is linked to external events and or conditions such as including but not limited to insufficient capacity of the systems wrong installation and or maintenance by the personnel which hasn t got the skills prescribed by the laws of the country of residence of the consumer negligence inability to use the product and wrong maintenance by the consumer with respect to what is reported and recommended by the instructions manual of the product which is part of the sales contract this guarantee will be void Damage to the product that cannot be related to manufacturing defects are also not included in this guarantee Similarly are excluded defects related to incorrect operation of the flue according to the legislation in force in the country at the moment of purchase Other exclusions include all product defects due to carelessness accidental breakdown tampering and or damage during transport scratches dents etc interventions carried out by unauthorised personnel and further damage caused by incorrect interventions by the consumer trying to arrange the initial malfunction The following consumables are excluded by the guarantee gaskets ceramic or tempered glasses cast
31. ion If the exhaust is not inserted in an existing flue a vertical section with a windproof end piece is required UNI 10683 The vertical duct can be inside or outside the building If the smoke duct is inserted in an existing flue it must be certified for solid fuel If the smoke duct is outside the building it must always be insulated The smoke ducts must have at least one airtight inlet for flue gas sampling All the sections of the flue gas duct must be accessible to inspection Inspection openings must be provided for cleaning 9 CHIMNEY CAP The chimney caps must meet the following requirements they must have a useful outlet section no less than double that of the chimney ducted system on which it is installed they must be adapted in order to prevent the penetration of rain and snow in the chimney ducted system they must be built so that in the event of winds coming from all directions and from any angle the expulsion of combustion products is in any case ensured EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY Protection from rain and wind Protection from rain and wind Insulated flue Max 3 mt all 3 5 Insulated T fitting with inspection plug T fitting Condensation proof with T fitting with inspection So inspection plug plug gt LEO
32. lay e To de activate press key 4 until COMFORT OFF appears on the display Cor WHEN THE COMFORT MODE IS ACTIVE THE LED FOR FAN 1 WILL FLASH ON THE CONTROL PANEL WHEN THE COMFORT FUNCTION IS ACTIVATED USING KEY 4 THE STOVE WILL ALWAYS OPERATED AT REDUCED FAN SPEED ENABLE CHRONO It allows to enable disable the chrono and the various time slots When enabling the time slots besides activating ON and de activating OFF it is also possible to select the COMFORT function for selected time slots CONTROLS PROCEDURE press key 5 for a few seconds until SET CLOCK appears Press key 3 several times to reach ENABLE CHRONO Press key 5 to confirm and use keys 2 3 to enable ON or disable OFF the chrono Use keys 4 5 to select the desired time slot Press keys 2 3 to enable ON or disable OFF the COMFORT mode for the selected time slot Press key 1 several times to confirm and exit the menu 9 4 CHRONO The chrono allows to program 2 time spans within a day to use every day of the week The switch on and switch off time can be set in every time slot along with the days of use of the programmed time slot RECOMMENDATIONS Example The ignition and switch off times must be within the arc of one day from 0 to 24 and not over several days Switch on time 07 00 CORRECT Before using the chrono function set the current day and time Switch off time 18 00 Therefore check that the points listed in the Set clo
33. liance has been installed as well as the instructions contained in this manual INSTALLING INSERTS When installing inserts access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during extraction operations Any wiring for example the power cable or room probe must be positioned so as not to be damaged during movement of the insert and must not come into contact with hot parts VENTILATION AND AERATION OF THE INSTALLATION PREMISES Ventilation is deemed sufficient when the room is equipped with air inlets according to the table Percentage of the Appliance categories Reference standard net opening section with respect to the appliance fumes outlet section Minimum net opening value of the ventilation duct UNIEN 14785 mM UNI EN 303 5 4pa reference for Italy according to standard UNI10683 All national regional provincial and municipal laws and standards in force in the country where the appliance is installed must be complied with ENGLISH 5 OExtraflame In the presence of type B gas appliances with intermittent operation not intended for heating they must have their own aeration and or ventilation opening The air inlets must meet the following requirements they must be protected with grids metal mesh etc but without reducing the net useful section they must be made so as to make the maintenance operations possible positioned so that they canno
34. luded by the guarantee 6 If the product is repaired in one of the Authorised Technical Assistance Centres indicated by Extraflame S p A and if the product is replaced transport will be free of charge If the technician can repair the product at the user s place of residence and they refuse transport to the workshop and redelivery will be paid by the consumer 7 After the 24 months of the guarantee have elapsed any repair intervention cost will be completely borne by the consumer 8 In the case of disputes the only competent court is that of the Extraflame S p A registered office Vicenza Italy 26 ENGLISH OExtraflame ADDITIONAL WARNINGS Only use the fuel recommended by the manufacturer The product must not be used as an incinerator Do not use the product as a ladder or supporting structure Do not place laundry on the product to dry it Any clothes horse or similar objects must be kept at due distance from the product Danger of fire or damage to the coating The user is fully liable for any incorrect use of the product The manufacturer bears no civil or criminal liability for incorrect use Unauthorised tampering of any nature or replacement of spare parts of the product with non original parts may endanger the operator and the manufacturer bears no civil or criminal liability for this Large parts of the surface of the product can get very hot door handle glass smoke outlet pipes etc Please therefore
35. mbols on the remote control and on the battery If the remote control is off because it has no batteries the stove can be controlled from the control panel on top of it While replacing the battery pay attention to the polarity by observing the symbol on the inside For operation 1 CR2025 3V lithium buffer battery is required compartment of the remote control THE BATTERIES USED CONTAIN METALS HARMFUL FOR THE ENVIRONMENT THEY MUST THEREFORE BE DISPOSED OF SEPARATELY IN APPROPRIATE CONTAINERS COMMISSIONING SETTINGS Once the power cable at the back of the stove has been connected move the switch also located on the back to I The switch at the back of the stove powers the stove board The stove remains off and a first screen appears on the panel reading OFF MAINS FREQUENCY 50 60HZ In the event the stove is installed in a country with 60Hz frequency the stove will display frequenza rete errata Mains frequency incorrect Vary the frequency as described below CONTROLS PROCEDURE Press key 5 Select 50 60Hz frequency with key 2 3 Confirm using key 5 and exit the menu by pressing key 1 ENGLISH 11 OExtraflame ADJUSTING TIME DAY MONTH AND YEAR Set clock allows to adjust the time and date CONTROLS PROCEDURE Press key 5 for a few seconds until SET CLOCK appears Confirm using key 5 Use key 3 to select the day Press key 5 Use the same procedure 5 to move forward 3 to set to
36. ng and cleaning Y Room air fan disassembly and removal of dust and any pellet debris Air intake pipe inspection and of flow sensor cleaning ENGLISH 23 OExtraflame DISPLAYS O_O a PELLET FEEDING The feeding of the pellet during the ignition phase is in progress The ignition phase is in progress MET The start up phase is in progress The normal work phase is in progress The stove is modulating The automatic burn pot cleaning is in The automatic burn pot cleaning not in 1st power is performed progress at pre established intervals of continued working BURN POT CLEANING FINAL CLEANING AS stove is switched off final cleaning is in progress The final cleaning phase lasts about 10 STAND BY nas onan ee PRAGA To deactivate the STAND BY function see the specific chapter and in stand by for re ignition Stove off due to an external i STAND BY EXT i Lui To deactivate the STAND BY function see the specific chapter thermostat waiting for re ignition When the stove switches off it is necessary to wait for the complete shutdown of the fumes motor before cleaning the burn pot The stove can only be re ignited when these operations have been performed A new ignition is attempted when the stove has just been switched off COOLING STAND BY COOL STDBY BLACK OUT The stove is cooling due to black out On completion of the cooling phase it will re ignite automatically Room thermostat set at minimum In
37. ppliance s safety and you may no longer be entitled to the warranty conditions By following the cleaning schedule reserved to the user and reported in the user and maintenance manual one ensures correct combustion in the generator over time thereby preventing any anomalies and or malfunctions that may require more work to be performed by the technician Requests for routine maintenance are not covered by the product s warranty DOOR ASH DRAWER AND BURN POT GASKETS The gaskets ensure the tightness of the stove and its consequent proper operation They must be checked periodically in the event they are worn or damaged they must be replaced immediately These operations must be carried out by a qualified technician CONNECTION TO THE FLUE Vacuum and clean the pipe that leads to the flue yearly or whenever necessary If there are horizontal sections any residue must be removed before it obstructs the flue PUTTING THE EQUIPMENT OUT OF SERVICE END OF THE SEASON At the end of every season before turning off the stove we recommend completely emptying the pellet tank and using a vacuum cleaner to clear up any pellets and dust residue inside it You should also disconnect the generator from the mains and to ensure greater safety especially if there are any children around remove the power supply cable Routine maintenance must be performed at least once a year gt IF THE POWER SUPPLY CABLE IS DAMAGED IT MUST BE REPLACED BY THE AFTER SALE
38. s START PRG2 START Press key 5 to confirm and continue PRG1 programming The scrolling text START PRG1 OFF will appear Press key 5 to confirm and continue programming The text START PRG2 OFF will appear 1ST TIME SLOT SWITCH ON Using keys 2 3 enter the time 08 00 START which corresponds to the switch on time of PRG1 the 1st time span The START PRG1 text will appear followed by the time set To confirm and continue programming press button 5 Press button 4 to go back to 08 00 the previous parameter 2ND TIME SLOT SWITCH ON At this point the second time slot must be START programmed PRG2 The sequence to be followed is the same and is repeated as per the 1ST TIME SLOT SWITCH ON 2ND TIME SLOT SWITCH ON At this point the second time slot must be programmed The sequence to be followed is the same and is repeated as per the 1ST TIME SLOT SWITCH ON On this occasion simply enter the time for example start at 15 00 and Stop at 22 00 and to activate the days Saturday and Sunday by setting them at ON WHEN THE WEEKLY PROGRAMMER IS ACTIVE A BOX OF THE RELATIVE ICON WILL APPEAR ON THE CONTROL BOARD 16 ENGLISH OExtraflame CLEANING AND MAINTENANCE ALWAYS FOLLOW THE INSTRUCTIONS IN MAXIMUM SAFETY CONDITIONS Make sue the power cable is unplugged since the generator could be programmed to start That the generator is cold in its entirety The ashes are completely cold Ensure an effective exchang
39. sured during installation between the internal and external environment is greater than 4 Pa INSTALLATIONS IN BATHROOMS BEDROOMS AND STUDIO FLATS Installation in bathrooms bedrooms and studio flats is only allowed for sealed or closed hearth appliances with ducted combustion air taken from the outside POSITIONING AND SAFETY DISTANCES The support surfaces and or points must have a suitable capacity to bear the overall weight of the appliance accessories and coverings If the floor is made of a combustible material we recommend using a non combustible material to protect the front part from any burnt material which might fall during routine cleaning operations The generator must be level to function properly The adjacent side and rear walls and the supporting surface must be made of non combustible material Air inlet MINIMUM DISTANCES The appliance may be installed near combustible or heat sensitive materials as long as Noor protection they are placed at appropriate safety distances specified on the label shown at the beginning of the manual page 2 In the event of non flammable materials there must be a distance of at least 50mm to the side and to the rear For products fitted with rear spacers they can be installed flush with the wall solely with the back against the wall One must also bear in mind all laws and national regional provincial and town council regulations in force in the country in which the app
40. t be obstructed The clean and non contaminated air flow can also be obtained from a room adjacent to that of installation indirect aeration and ventilation as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room cannot be used as a garage or to store combustible material or for any other activity with a fire hazard bathroom bedroom or common room of the building COMBUSTION AIR CONNECTION When connecting the combustion air the pipe used should be flame retardant and must withstand at least 110 C FLUE GAS EXHAUST The heat generator works in depression and is equipped with an outlet fan for flue gas extraction There must be a single exhaust system for the generator Using a flue that is shared with other devices is not allowed The components of the flue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with UNI TS 11278 in the event of metal chimneys with particular attention to that stated in the specification UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNI EN 1806 in the event of non metallic chimneys The length of the horizontal section must be minimal and in any case no longer than 3 metres with a minimum upward slope of 3 There must not be more than 4 direction changes including the one due to the use of the T element A T fitting with a condensation collection cap must be provided at the base of the vertical sect
41. this way the stove only works at 1st power independently value from the power set To exit this function just raise the room temperature using button 4 and then key 2 The stove works at set start without ever modulating To escape HOT Set room thermostat set at maximum this function just lower the set temperature using key 4 and then key 1 When this message appears contact the authorised technician for ordinary cleaning of the appliance SERVICE If cleaning is not performed the message will be displayed at every ignition but without interrupting normal stove operation 24 ENGLISH value OExtraflame ALARMS EXPLANATION SOLUTION On indicates the presence of an alarm Off indicates the absence of alarms l i indicates the presenceeranalann Flashing indicates the deactivation of the depression sensor The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have passed from displaying the same alarm Fault related to the flue gas exhaust The restoration operations must be carried out by an authorised FUMES FAILURE E a p y motor technician FUMES PROBE Fault relatedito thefumes probe Ea operations must be carried out by an authorised Check the pellet flow see Pellet feed adjustment Check that the machine is clean including the fumes route Do not rest cloths on the machine Other restoration operations must be carried out by an authorised technician
Download Pdf Manuals
Related Search