Wireless Tyre Pressure Monitoring System
Contents
1. Affected p wi kesr during its turn when the unit is in it will sound one long beep followed Temperature icon will light and the indicator will flash Note Press SET to turn off the sound If the sound is turned offgthe Warning will remain on the display until the problem 1s taken care of by the user 25 Page ARTRONI TEMPERATURE ABOVE 90C 194F Affected tyre will flash during its turn when the unit is in Operating Mode Unit will sound one long beep follow by one short beep and a one second delay Temperature icon will light and the Temperature Bar indicator will flash Note Press SET to turn off the sound If the sound is turned off the Warning will remain on the display until the problem is taken care of by the user TEMPERATURE ABOVE 100C 212F Affected tyre will flash when the unit is in Oper Mode Unit will sound one long beep followed by short beeps and a one second delay Temp i 26 Page ZARTRONIX TPMS OPTIONAL ACCESSORIES Battery Pack 8AA Battery Pack allows display unit to be carried around for easier setup Users do not have to rely on the power from the vehicles cigarette lighter power cord Useful when setting up vehicles with a lot of wheels Your TPMS supports up to 27 wheels LF Remote Control The LF remote control is used to control the tyr 2 main functions include e Learning Keys A B amp C Press this key to force the sensor to tra inflating or deflating the tyr2. Restoring a Tyre Location To restore a deleted tyre location go into Teaching Mode to allow the system to re learn the location of the tyre to be restored NOTE If no activity for 240 seconds the unit will revert to Operational Mode the high force expelled by the ty may be damage by this forceaPl is broken If this is done incorrectly the sensor anyone removing or servicing your tyres that internal tyre sensors are 1 and th bead must be broken on the opposite side of the sensor Any dama not adhering to this is not covered by warranty Break Tyre Bead here lve 15 located here 22 Page ARTRONI REACTING TO ALERTS NO SIGNAL Affected tyre will flash during its turn when the unit is in Operating Mode Unit will beep once every second and Antenna Signal icon shows with no bars Pressure and Temperature bar indicators will light but no numbers will be in the Pressure and Temperature display Press SET to turn off the sound If the sound is turned off the warning will remain on the display for 15 seconds before moving to the next tyre unless the problem is rectified by the user NOTE Interference may affect the signal s recefti CAR BATTERY LLEN EEE BERIE BEREE LL BERRE E RIINI Note Press SET to turn off the sound If the sound is turned off the Warning will remain on the display until the problem is taken care of by the user 23 Page ARTRONI UNDER IN
3. ARTRONIX Wireless Tyre Pressure Monitoring Syste vee BGG 5 TELLE TU n LL i noo s m 00 0 vou ima SELS pe Fi Zartronix Phone 1300 76 44 76 Unit 1 2 Narooma Street Moorabbin Victoria 3189 Australia E mail sales zartronix com Website www zartronix com ZARTRONIX FACTORY TPMS CONFIGURATION SETTINGS We have preconfigured your unit for your convenience please ens tyre sensors are installed in the correct positions as marked If n Test will have to be performed to re learn the correct tyrepesi TEMPERATURE Celsius Fahrenheit Tyre Pressure s SP1 2 Page ZARTRONIX TABLE OF CONTENTS Tyre Pressure Monitoring System TPMS NOCE rere Precaution irske Sr NE Specifications of TPMS TPMS Components Display Installation Tyre Sensors Installation Display Unit Introduction Configuring the TPMS unit LE eS oe Operating Mode Function Mode Unit Mode er E errr 15 Setup MORE SU 55 20 a 16 Pres Etup ee cccncccccccccccnccccees 18 iler Mount Dismount cccccccsccccccccees 18 Mode ne on 19 Tyre Rotation Program 19 Learning Mode se oo LU Deleting a Tyre 22 uesssssesssesesoeooo 21 Restoring a Tyre essesessessesoeoooe 22 Tyre Rim Maintenance cccccssccccccccccceceess 22 Reacting to Alerts 23 10 TPMS Optional Accessories s ssssssssssosscccccosoosee eve 27 11 Appendixes die ee sens no
4. from all tyres on both the vehicle and trailer or 9 Page ZARTRONIX TYRE SENSOR INSTALLATION Process 1 Remove tyre from the vehicle Deflate the tyre and remove the tyre f Remove the old valve stem Seek assistance from qualified p 2 Each sensor has a showing the wheel position it n Front Right 2 Rear Right 4 Spare metal valve stems can be purchased from the dealer or many auto spare retailers if required NOTE Do not hit or strike the tyre sensor 10 Page ARTRONI Clean the area of the rim around the valve of debris Be sure each of the rubber seals is positioned on either side of the rim and then install the metal valve stem Next install the sensor and tighten with one nut provided using a 12mm spanner When the nut becomes tight insuring a good seal rubber seal should be slightly bulging install the second locking nut to complete the job Clean the inside of the tyre from any dust and inflate the tyre to the proper pressure as recommended by the tyre manufacturer this will automatically activate the tyre sensor properly installed This should be carried out by qualified personnel 11 Page ARTRONL DISPLAY UNIT INTRODUCTION Lartronix Monitors the vehicles battery in Operation Mode If it is above 15 5V or below 11 5V it will flash and has a warning sound 12 Page ARTRONI Pressure Warning Will light when
5. the tyre sensor detects any irregularities in tyre pressure Flat Tyre Will light when a flat tyre is detected or a sudden drop in pressure High Temperature Will light when the temperature inside the tyre is above 85 C 185 deg F Tyre Configurations e 8 different tyre modes sure kPa bar or psi fferentiate between normal 2 different units of temperature Celsius C or Fahrenheit F Different colours to differentiate between normal Green and high temperature Red above 85 degrees Celsius e Displays actual temperature value on the display unit 13 Page ZARTRONIX CONFIGURING THE TPMS UNIT OPERATING MODE The TPMS display unit will monitor each tyre for 10 seconds and then proceed to the next tyre Any problematic tyre will be monitored for 15 seconds before proceeding to the next tyre It will keep displaying the warning code until the problem has been taken care of by the user For the alerts warnings codes please refer to the Reacting to Alerts section on page 19 The tyre being monitored will light and it information will be displayed 1 e p re temperature tyre sensor battery level an signal strength NOTE User has the option to turn off th rning sound by pressing SET button Iriran em will quit the Function Mode and return to Operating Mode 14 Page ARTRONI UNIT MODE Pressure and Temperature Units Setup 1 Press and hold FUNC button for 3
6. 4 5 1 1 1 1 1 4 440 1 1 1 1 1 0 0 0 1 0 0 0 4 460 470 480 520 2 2 22 520 23 5308 24 540_ 36 39 2 59 550 590 3 b 74 0 2 8 115 2 28 5 1190 172 6 11 9 1200 174 0 3 5 7 0 1 3 2 4 3 8 5 5 3 6 460 66e 7 470 68 2 8 480 9 o 74 0 3 5 6 7 8 9 2 0 4 0 5 0 6 0 7 0 8 0 9 1 0 BER L R 60 9 13 14 1 5 450 65 3 16 RE 18 69 6 1 9 20 2 Fa 7 4 b 2 5 B A 22 8 2 9 590 3 0 600 129 1 900 130 5 80 ee 6 0 1130 1140 1150 160 1170 1180 1190 1200 29 Page JARTRONIX Temperature Conversion Table 30 Page ARTRONI WARRANTY Zartronix warrants to the original end user that the product purchased is free from def of Zartronix Zartronix reserves the right to replace defected products wit refurbished unit to be functionally equivalent to new The Warranty is void and inapplicable if 1 The product has been used or handled other than accordanc e instructions in the user manual 2 the product is abused misused damaged tor K by anyone other than a 3 The damage is due from being repaire 4 The damage is due from shippi The damaged product must be delivere i rtronix or its authorized repair centre The RETURNED PRODUCT MUST NIED BY A WR
7. 6 Page ARTRONI 5 Press SET to accept the preset or default pressure Default value displayed Press 030 7 The pressure value on the far right digit will flash BH first To change the pressure value press FUNC T D button The displayed number will increase by 1 every time the FUNC button is pressed Continue to press the button until you see the value you want The number will loop from 0 to 9 and then back to 0 Press SET to accept the input value Simply repeat for the remaining digits 6 Press FUNC to change the pressure value NOTE When entering the pressure as 28 psi please enter it as 028 psi Trailer or 2 Default Pressure 8 Display will automatically enter Default Pressure Setup Mode Correct Pressure Entered iea will display PS Pressure Saved and y Unit will beep once for confirmation l display ERR Pressure Error amp Display Unit will beep twice User will automatically be returned to step 6 to re enter information If error ERR occurs for the second time the system will use the default values for the pressure instead 11 Unit will now return to Operating Mode a Unit wi W retu p 8 Incorrect Pressure Entered 17 Page ARTRONI NOTE 10 seconds of inactivity will result in the system exiting the Pressure Setup Mode and returning to the Operating Mode 1 Press and hold FUNC button for 6 seconds until Message Area displays SEL Select 1 SP1 or 27 SP2 standard pressure v
8. FLATION 30 Affected tyre will flash during its turn when the unit is in Operating Mode Unit will beep once every two seconds Pressure bar indicator will flash at 70 and the tyre leak icon will light The 30 under inflation value in pressure is display based on the default set by the user Note Press SET to turn off the sound If the sound is turned off the Warning will remain on the display until the problem is taken care of by the user OVER INFLATION 25 Pressure bar Nes will flash at 75 andthe ty icon will light The 25 over inflation value in p h during its turn when the unit is in twill beep once every two seconds or will flash at 70 and tyre leak icon Note Press SET to turn off the sound If the sound is turned off the Warning will remain on the display until the problem is taken care of by the user 24 Page ARTRONI FAST LEAK Affected tyre will flash when the unit is in Operating Mode Unit will beep twice every second and tyre leak icon will light Note Press SET to turn off the sound If the sound is turned off the Warning will remain on the display until the problem is taken care of by the user FLAT TYRE or NO PRESSURE Affected tyre will flash when the unit is in o ing Mode Unit will beep twice every second and the icon will light Note Press SET to turn off the sound Tath turned off the Warning will remai i problem is taken care of by the TEMPERATURE ABOVE 80C 176F
9. ITTEN DESCRIPTION OF This warranty is vahid 1 purchase this warranty is limited to the terms stated herein Zartronix s to the product so rights which va le for any special incidental or consequential damages relating 31 Page JARTRONIX WARRANTY FORM Contact Details Name Company es ee l ase attach a copy of City the purchase receipt State Phone Fault Description 32 Page
10. age JARTRONLX DISPLAY INSTALLATION Connect the Mini USB End of the Power adaptor to the x display unit Attach the antenna by gently screwing it on clockwise finger tight see Antenna Extension Cable notes on Page 6 if required Install the display unit into the desired location e Install the air vent clips for vent mounting e Apply the enclosed double sided adhesive to the base of the Display for dashboard mounting Connect the Power e e Note It For the Hard Wire Kit es according to the wire Ignition BATTERY ill start receiving signals from tyre sensors re sensor has been installed and the tyre s E It may not be necessary to set the tyre position on e TPMS Unit as this will generally be pre set at the factory It is important to reinstall the tyres according to the tyre position on the sensors label For Vehicles with more than 4 wheels please set up tyre locations in accordance with page 14 8 Page ARTRONI NOTE We highly recommend using the antenna extension cable when towing a caravan or trailer to insure optimum signal reception Simply unscrew the antenna and connect the antenna cable to the display Reconnect the antenna at the other end of the cable and secure with at least 10 cms of electrical tape to prevent dust and water entering the connection The best location for the antenna is outside the vehicle and near the tow bar this ensures a good signal can be received
11. alue for each axle in turn First row tyres second row tyres third row spare tyre tyres of trailer will now flash sequentially on the display unit Press SET for SP1 or FUNC for SP2 Press and hold SE I an JNC buttons simultaneously for seconds for 9 secont Message Area displays iler Mount amp Dismount function only works M05 M06 M07 amp MO8 18 Page ARTRONI TYRE SETUP MODE There are two functions available in this mode e Tyre Rotation Program Rotation of existing tyres after the tyres hav n rota e Teaching Mode to reprogram including deleting all tyre sensomposiStion TYRE ROTATION PROGRAM 1 Simultaneously press the SET and FUNC buttons to enter Tyre Setup Mode 2 The Display will show CHG for change tyre position NOTE The Tyre Rotation a Ls only available in MODE 01 in all other Press FUNC for Yes Pressing will enter Teaching Mode SeesBe Imirt iagonally direction ged Front Left for Rear t Right for Rear Left NE will toggle between the two e display will flash indicating which ye mode is selected 1 Front Left with Rear Left amp Front Right with Rear Right ye Press SET for Yes to accept this mode OK will be displayed Press SET for Yes to swap tyres 7 Press FUNC for No no change will be saved and IDX will be displayed 19 Page ARTRONI NOTE If no activity for 20 seconds the unit will advance to the Teaching M
12. e s pressure position It also has the function position Sleep Key D It will force the sensor i t will save the tyre sensor s battery p k if the sensor is removed r pressure in the tyre As soon 27 Page ARTRONI Standard Valve The TPMS uses a standard metal valve stem available at most automotive part stores Allows you to replace just the tyre valve stem if it is damaged or broken You do not have to replace the entire sensor With other TPMS units you have to replace both the valve and the sensor if either one is broken or damaged Tyre Sensor e Tyre sensors are available for the spare tyre s e To purchase more tyre sensorg Optional power cord to allow the play to be hard wired to the vehicles electrical system allowing unit to monitor tyres 24 7 Display only illuminates when ignition is switched on 28 Page ARTRONIX Appendix Pressure Conversion Table psi bar kPa Psi 4 6 8 1320 D 9 1 9 2 9 9 9 360 52 2 36 660 95 7 6 960 139 2 9 7 390 56 6 3 9 690 100 1 69 990 143 6 9 9 410 0 0 0 0 0 60 8 7 0 1 1 1 410 59 5 41 410 180071 1 102 1 1 1 800 116 0 8 0 1100 159 5 11 0 830 120 4 83 1130 163 9 11 3 840 121 8 8 4 1140 165 3 850 123 3 8 5 1150 166 8 7 86 1160_ 2 87 1170 6 88 1180_ 90 1 89 9 0 1 2 420 4
13. ode LEARNING MODE 1 Simultaneously press the SET and FUNC buttons to enter Tyre Setup Mode purpose of identification The Leak Test requires the tyre to be identified to be deflated or inflated by 5 psi 34 kPa or more within 4 minutes 20 Page ZARTRONIX e Remote Control Unit Triggering the sensor in the tyre to be identified is done by holding the remote unit close to the tyre sensor and pressing the Learning Key buttons A B or C on the remote Make sure that the POWER LED on the remote illuminates 5 When the Leak Test has been successfully performed the display unit will beep once in acknowledgement and display OK 6 The next tyre in sequence will now flash enabling the leak test to be performed for the remaining tyres hg 7 When all the tyres have been success identified the system will exit the eS Mode and return to the Operatin de During the Leak Test th all the possible tyr the Mode M01 MO08 you have chosen the tyre to be deleted 2 button The unit will display and beep once ess the FUNC button for Yes y shows SKP Skip The previous xs are retained and no action is taken oring for the spare tyre and any other tyre location not used in their configuration Mode 21 Page ARTRONI 4 The system then proceeds to the next tyre in the Leak Test if this was the last tyre then it would exit the Tyre Setup Mode and return to the Operating Mode
14. rte 29 Ne a din din 31 3 Page Tyre Pressure Monitoring System TPMS Thank you for purchasing your Tyre Pressure Monitoring System TPMS from Zartr for your protection from world leaders in design and manufacture Our TPMS inf the tyres pressure and temperature and quickly notifies you of problems such leak The TPMS will continually monitor your vehicles tyre pressure and te accurately 24 7 If the TPMS detects any irregularity in the tyres pressure quickly notifies the driver with an alarm and warnings on the colour action should then be taken to avoid accidents and ensure the safet passengers vehicle and other road users FCC Notice This device complies with part 15 of th This equipment has been tested an pursuant to part 15 of the FCC against harmful interferenc communications installation If this g the equipment off and on the user is encouraged to try to r more of the factoring measures PRECAUTION anges or modifications in construction of this device could void the user s authority to operate the equipment To comply with the FCC RF exposure compliance requirements this device s antenna must not be co located or operating to conjunction with any other antenna or transmitter 4 Page ARTRONI Your TPMS system is designed to monitor the tyres condition and alert the user if there is any irregularity detected Use of chemical sealants for temporary resealing or re infla
15. seconds to enter Unit Mode 2 The message area displays P 3 psiicon will light or the previously saved unit 4 Press FUNC to change pressure unit psi kPa bar psi 5 Continue to press FUNC for pressure unit selection 6 Press SET to confirm Pressure unit is then saved 8 The message area displays T 9 C icon will light or the previously saved unit 10 Press FUNC to change temperature unit C F C 11 Continue to press FUNC for temperature unit selection 12 Press SET to confirm the selectio is then saved psi or bar e To bypa itchange skip step 4 amp 5 Go to step e default unit settings The DASS be 10 lol tep 12 to confirm the default unit hgs Default temperature unit is in Celsius or previously saved unit o Exit Unit Mode do not touch any buttons for 20 seconds Changes will not be saved before step 5 and the system will use the default pressure unit and return to Operating Mode 15 Page JARTRONLX SETUP MODE Tyre Configuration amp Pressure Setup Q3 etc M08 M01 confirm the Vehicle Mode required ill then be saved immediately after step 1 DIGIT 3 DIGIT PE To bypass vehicle mode change skip step 3 amp 4 Go to step 5 to confirm the displayed Mode Or to EXIT without saving don t touch the display unit for 20 seconds Changes won t be saved and the system will use the preset or default vehicle mode 1
16. tion of tyre may affect orf ve damage the sensors function For your own safety please read and understand the instruction manual be installation and setup Please seek qualified personnel assistance for proper tyre sensor 1 ation e Only use the cigarette power cord supplied by Zartronix Do not use this power cord in any other USB device It is NOT USB compatible and may damage your USB device Zartronix shall not be held r spo amage caused to any USB device if you use this power adaptor i e When you unplug the power adaptor do adaptor If the power cable is damaged ont ct your dealer for replacement othe ull evice the cord It may damage the 5 Page JARTRONLX SPECIFICATIONS OF TPMS Sensor Specifications Estimated 5 to 7 years under normal operating condition Battery Voltage 36V A 4 Storage Temperature 55 C to 125 C Operating Temperature 40 Ct0125 C_ ET CE Temperature Resolution ECS e Pressure Ranges O psi 1 Pressure Resolution 0 2 psi 1 38 kPa O bsi 575 kPa Truck Operating Humidity Operating Frequency Sensor Weight Battery Life Operating Voltage 9V to 18V Operating Temperature 20 C to 85 C Monitored Temperature 40 C to100 C 6 Page ZARTRONIX TPMS COMPONENTS Tess ON 1 i 1 Air Conditioner Clip NJ DE 2 Weme SC CO CO ee 4 Metal Valve Stems 4 2 7 P
Download Pdf Manuals
Related Search