XLED 250 MANUAL
Contents
1. XLED 250 SPOT PR 8111 This product manual contains important information about the safe installation and use of this product Please read and follow these instructions carefully before installing and using the product and keep this manual in a safe place for future reference PR LIGHTING LTD http www pr lighting com INDEX SAFETY INFORMATION AND WARNINGS PRODUCT INSTALLATION POWER SUPPLY CONNECTION DMX CONTROL CONNECTION DMX TERMINATOR PRODUCT FUNCTION SETUP DMX START ADDRESS SETUP STAND ALONE MODE MASTER SLAVE MODE OPERATION MENU DMX PROTOCOL DISPLAY INFORMATION MAINTENANCE PRODUCT CLEANING TROUBLESHOOTING TECHNICAL DATA COMPONENT ORDER CODES CIRCUIT DIAGRAM NN FW a a e WNNNN O oun Every ex company fixture is tested completely and packed properly by the manufacturer The use explanations and warnings in this manual must be strictly followed Any damage caused by improper use will not be covered by the manufacturer and or dealer If any technical data changes further notice won t be offered ACCESSORIES These items are packed together with the product please check them Name Quantity Unit Remark XLR signal cable 1 PCS With plug and socket Safety cord 1 PCS This manual 1 PCS Gclamp 1 PCS Standard Q clamp 1 PCS Optional 2 17 SAFETY INFORMATION AND WARNINGS After receiving product please u2. 1 clamp on the BOTTOM of fixture with 2 retainers attached to the clamp Hang the fixture on the steel truss and fasten the retainers attached to the clamp Always ensure that the location that you are going to mount the unit is secure and is strong enough to support the weight of the unit See the WARNING as shown above To pass SAFETY CORD through the SAFETY HOLE on the back cover of the base of the fixture for safety Always ensure that the unit is firmly anchored to avoid vibration and slipping whilst functioning WARNING 1 The unit MUST be lifted or carried by the HANDLES instead of clamps 2 For safety the safety cord should bear 10 times of the unit s weight 4 17 POWER SUPPLY CONNECTIONS Connect the power cord as follows L live brown E earth yellow green N neutral blue Please be advised to notice power supply s voltage and frequency meet what are described on the nameplate of the product It is recommended that each unit be power connected separately so that they may be individually switched on and off IMPORTANT It is essential that each unit yellow green twin wire is correctly earthed and the electrical installation conforms to all relevant standards DMX CONTROL CONNECTION DMX OUT DMX IN DMX 512 FUNGTION 5 PIN 5 o l 5 DATA 0 j 3 0 0 j 3 3 Connection between controller and unit and between one unit and another must be made with a 2 core screened cable with each core
3. 50 60Hz POWER CONSUMPTION 120W 220V HEAD MOVEMENT Pan 540 Tilt 190 Pan Tilt Swap and Invert Function Auto position correction amp Magnetic sensor positioning COLOR SYSTEM LED 6500K Color wheel 8 Color 1 white GOLOS SYSTEM 1 Fixed Gobo wheel 11 Gobo 1 White Image size 15mm DIMMER 0 100 linearly adjustable STROBE Electronic strobe 0 3 20 F P S LENS ANGLE 20 CONTROL DMX512 5 pin interfaces 12channels in standard mode and 16channels in extended mode Master slave mode Stand alone mode Preset mode OTHER FUNCTIONS Adjustable Pan amp Tilt speed Fixture usage time display Software version display HOUSING High temperature engineering plastic IP20 13 17 WEIGHT 4 5 Kg SIZES See at below 337 23 285 06 14 17 LIGHT OUTPUT 6m 4m 2m 0m 2m 4m 6m 7m 5m 3m 1m 1m 3m 5m 7m Distance 0 lm 2m 5m 10m 15m ux 0 92903 2322 6 1032 3 371 6 92 9 413 200 OMPONENT ORDER CODES NO NAME PART NO QUANTITY REMARK 1 POWER SUPPLY 190010131 1PCS 100 240V AC 2 0A 2 LED 150020215 1PCS CBT 90 W 3 FIXED FOCUS LENS 071100030 1PCS 4 CONDENSER LENS 071100019 1PCS 5 FUSE 270041037 1PCS 5x20 3 15A 6 TILT PAN BELT 290151337 2PCS HTD 3M 297 7
4. 7015 FAN 030060078 1PCS 24V ADO724HB D71 8 4010 FAN 030060070 1PCS 24V AD0424HB 9 PAN TILT MOTOR 030040175 2PCS 10 PAN TILT MOTOR DRIVE BOARD 230060155 1PCS 11 COLOR WHEEL MOTOR 030040176 1PCS 12 GOBO WHEEL MOTOR 030040177 1PCS 13 COLOR AND GOBO WHEEL MOTOR DRIVE BOARD 230060179 1PCS 14 COLOR AND GOBO WHEEL BELT 290151263 1PCS HTD 126 3M 15 LED DRIVER PCB 192010144 1PCS 16 DISPLAY PCB 230060186 1PCS 15 17 Machine Crust CIRCUIT DIAGRAM Hall Sensor RA LED Driver Board A LED DRV3PCB Pattern Motor MAIN_X_Y ST Main Display Board MAIN i y DMX IN DMX OUT Color Motor XY Driver Board XY DRVPCB Hall Sensor Hall Sensor 16 17 PR LIGHTING LTD 1582 Xingye Avenue Nancun Panyu Guangzhou 511442 China TEL 86 20 3995 2888 FAX 86 20 3995 2330 P N 320020129 Version 20130108 17 17
5. and DOWN you can set the address Press button ENTER to confirm when powered on next time it will show the latest number you saved Press button FUNG it will return to the upper menu one by one 6 17 STAND ALONE MODE Operate the fixture without connecting a controller enable the master mode in the operation panel the fixture will run in Stand Alone mode automatically MASTER SLAVE MODE If many fixtures are connected under Master Slave mode use XLR XLR control cable to connect the first fixture s DMX output port with the second fixture s DMX input port then to connect the second fixture s output port with the third fixture s input port and so on until all the fixtures are connected the last thing is to plug the terminator at the last fixture s output port In this case the first fixture is the master others are slaves Set the master s address at 001 Master can be set at any mode STD mode or extended mode and slave should be set at same mode as the master s After powered on the group will run under Master Slave mode MASTER DMX IN FROM CONTROLLER DMX OUT DMX OUT TERMINATOR 7 17 OPERATION MENU 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL AddR XXX DMX Address XXX 1 512 STd dmxX Standard mode DMX m
6. having at least a 0 5mm diameter Connection to the DMX512 input and output ports of the unitis via 5 pin XLR plugs and sockets which are included with the unit The XLR s plugs and sockets are connected with wires as shown in the figure above Note care should be taken to ensure that none of the pins touch the metallic body of the plug or each other XLR s plug and socket must not be connected with XLR control wire in any way other than shown as above The fixture accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below MASTER DMX IN DMX IN FROM CONTROLLER DMX OUT DMX OUT TERMINATOR 5 17 DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX512 control signals The DMX terminator is simply a Canon connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last fixture in the chain The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120 4 OHM resistor across pins 2 and 3 in an XLR p
7. 9 Shake 9 Speed from fast to slow 240 247 Shake 10 Speed from fast to slow 248 255 Shake 11 Speed from fast to slow 6 Pan 000 255 Pan 540 7 Pan 16 Bit 000 255 Pan 16 bit precision rotation 8 Tilt 000 255 Tilt 190 i Tilt 16 bit precision rotation 9 Tilt 16 Bit 000 255 Pan tilt 10 000 255 Speed from slow to fast speed 000 048 Reserved 11 Control 049 255 Reset 11 17 INDICATION OF LED DIGITAL TUBE A A er or On DMX signal OK Decimal point of the first digital tube Off No DMX signal l a ee On Master slave signal is OK Decimal point of the third digital tube Off No master slave signal A A or On When setting master mode Decimal point of the fourth digital tube Off When setting slave mode Parameters that LED digital tubes display Flash Parameters not saved press ENTER to save them MAINTENANCE If the Fixture does not function check if the fuses on the power socket of the unit is broken or not if broken they should only be replaced by fuses of the same specification Should there be damaged call a qualified technician before replacement The fixture has thermal protection device that will switch off the unit in case of overheating Should any case like this happen check if the fans work well or fans and fan screens are blocked restart the fixture before the problems have been found and resolved Any maintenance work should only be carried out by qualifie
8. d technicians PRODUCT CLEANING To ensure the reliability of the fixture it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent containing chemical elements Cleaning intervals depends on the environment in which the fixture operates and use frequency A soft cloth and typical glass cleaning products should be used in cleaning the fixtures It is recommended to clean the external optical system at least once every 20 days Do not use any organic solvent e g alcohol to clean the housing of the apparatus to avoid damages TROUBLE SHOOTING PROBLEM ACTION gt Check if the fuse on the power socket is broken or not gt Check the status of the fuse The fixture can not start The lamp works normal but the fixture gt Check if the fixture s start address is set properly doesn t respond to the controller gt Check if XLR signal cable is broken or not gt Make sure the fans work normally and if dirt blocks fans and fan The fixture only functions intermittently screens The beam appears dim and brightness gt Check if the lamps reach the end of their lives decreases apparently gt 0 if external and internal optical systems are clean or not 12 17 TECHNICAL DATA LIGHT SOURCE LUMINUS PHLATELIGHT LED CBT 90 W VOLTAGES 90 264VAC
9. itted from the master includes DMX mode display setting operation mode Including user memory 9 17 DMX Protocol Short Standard M Mode Mode Function DMX Value Description 1 1 Strobe o 001 255 Strobe speed from slow to fast 2 2 Dimmer 000 255 Linear dimming from dark to bright 3 a 000 255 Linear dimming from dark to bright Macro 0 15 White 16 31 Color 1 32 47 Color 2 48 63 Color 3 64 79 Color 4 80 95 Color 5 3 4 Color wheel 96 111 Color 6 112 127 Color 7 128 143 Color 8 144 175 Forward Rotation Speed from slow to fast 176 223 Stop at White light 224 255 Reverse Rotation Speed from slow to fast 0 15 White 16 23 Gobo 1 24 31 Gobo 2 32 39 Gobo 3 40 47 Gobo 4 48 55 Gobo 5 56 63 Gobo 6 64 71 Gobo 7 4 5 72 79 Gobo 8 wheel 80 87 Gobo 9 88 95 Gobo 10 96 103 Gobo 11 104 135 Forward Rotation Speed from slow to fast 136 167 Reverse Rotation Speed from slow to fast 168 175 Shake 1 Speed from fast to slow 176 183 Shake 2 Speed from fast to slow 184 191 Shake 3 Speed from fast to slow 10 17 192 199 Shake 4 Speed from fast to slow 200 207 Shake 5 Speed from fast to slow 208 215 Shake 6 Speed from fast to slow 216 223 Shake 7 Speed from fast to slow 224 231 Shake 8 Speed from fast to slow 232 23
10. lug and insert into the DMX out socket on the last unit in the chain PIN 2 PIN 3 PRODUCT FUNCTION SETUP BEBE FUNC DOWN ENTER Fixture s address and function code configuration can be set conveniently via button switch and LCD display Press button ENTER more than 5 seconds to unlock panel LED display shows the fixture s function menu Each Option of the main menu has its own sub menu Each menu stands for specified function of the fixture please see the details in the following Press button UP or DOWN if you want to set or browse through the various Setup Options Press button ENTER to save your settings or enter the sub menus Press button UP or DOWN to change the parameters increase or decrease the numbers Press button FUNG it will return to the upper menu one by one If the button not pressed the system will go back to display status automatically TO SET THE DMX START ADDRESS If many fixtures are controlled by the controller each fixture should be set with a start address to receive signals sent by the controller and respond to it The fixture have 2 DMX modes There are standard mode and extended mode For example standard mode has 11 channels so set the No 1 Fixture s address 001 No 2 Fixture s address 012 No 3 Fixture s address 023 and so on Switch on the Fixture Press button ENTER more than 5 seconds to unlock panel Press button FUNC to display DMX address Press button UP
11. not in use or before it being cleaned please hold the plug and unplug the power cord Never pull out the plug by tugging the power cord The fixture should always be installed with a secondary safety fixing A safety cord is supplied for this it should be attached as shown in installing the unit section At the back cover of the base there is a safety hole for the safety cord for safety installation please run the safety cord supplied with the fixture through the safety hole to support the safe installation Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired for example by cracks or deep scratches Exterior surface temperatures of the luminaire after 5 minutes operation is 45 C when steady it achieves 50 C There is no user repairable parts inside the fixture do not open the housing and never operate the unit with the covers removed Before the use of the fixture please check if the covers are fixed well and all screws are fastened If any questions don t hesitate to consult your dealer or the manufacturer Important Always disconnect from Power Supply when the device is not in use or before cleaning or any maintenance work 3 17 PRODUCT INSTALLATION WARNING Please run the safety cord through safety hole and make sure tha the cord is property secured Take 1 clamp and 1 the safety cord out from the package and mount
12. npack and check if there are any damages caused by transportation Do not use the fixture if transportation damages occur and contact the manufacturer or the dealer as soon as possible The product is only for indoor use IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow its contact with water or any other liquids The unit is only intended for installation operation and maintenance by qualified personnel The product must be installed in a location with good ventilation at least 50cm from adjacent wall surfaces Be sure that no fans and ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 1 3m 1 3m Avoid looking into the light from the fixture directly especially to Epileptic Patients The light is harmful to the eye Do not attempt to dismantle and or modify the product in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the fixture It is essential that each fixture is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the powercord come into contact with other cables If the fixture is
13. ode SHRT Default is STd Short mode disP ON Display setting OFF Default is ON digital CRT off if buttons not pressed in 5 minutes OFF xyCH Pan Tilt Swap off Pan Tilt Swap Default is OFF ON CNFG Pan Tilt Swap on Config Settings OFF xyCP Pan Tilt invert off Pan Tilt Invert Default is OFF ON Pan Tilt invert on SLAV mORS Slave mode Master Slave Settings Default is SLAV mAST Master mode FACT Factory Defaults yES TRmd 1 Transmit parameters yES XXXX Tne Fixture usage time ae Fixture usage time showed enan VER XXX Software version Software version showed ON LAmP Turn on LED Lamp OFF Turn off NO Color Cw1 CW8 Color 1 to Color 8 FORw Forward Rotation TEST STOP Test mode Stop REVE Reverse rotation NO No Gobo 1 FGw1 FGW1b wI Shake 1 to shake 11 Fixed Gobo wheel FORw Forward Rotation REVE 8 17 Reverse Rotation GWS1 GWSb Shake 1 to shake 11 Pan 0 255 540 TILT 0 255 190 P TS a Pan Tilt speed 0 255 Pan Tilt speed RESE Reset YES dmx DMX mode PRUN Run preset memory ERUN Run user program CHO1 Strobe 0 255 CHO2 Dimmer 0 255 MENU Operation mode 0 255 CHO4 ET XX Fixed Gobo wheel 0 255 User program ETO1 ET16 CHS 0 255 Pan CH6 Tilt 0 255 CH7 Pan Tilt speed 0 255 CH8 0 255 Scene hold time Time X 40mS Remark 1 Inthe synchronous control of multiple fixtures parameters can be transm
Download Pdf Manuals
Related Search