R5 Came User Manual
Contents
1. Outdooree R5 using the provided adjustable strap or the tripod socket 6 Sensing Angle and Distance Test To test whether the Outdooree R5 can effectively monitor the area you choose this test is recommended to check the sensing angle and monitoring distance of the Outdooree R5 To perform the test Entering into SETUP mode 23 Make movements in front of the camera at several positions within the area where you expect the game or subjects to be Try different distances and angles from the camera lf the motion indicator LED light blinks it indicates that position can be sensed If it does not blink that position is outside of the sensing area The results of your testing will help you find the best placement when mounting and aiming the Outdooree R5 The height away from the ground for placing the device should vary with the animal size appropriately In general 3 to 5 feet is preferred You can avoid potential false triggers due to temperature and motion disturbances in front of the camera by not aiming it at a heat source or nearby tree branches or brush especially on windy days 24 7 Switching ON the Camera Once you switch to the ON mode the motion indicator LED red Fig 3 will blink for about 10 seconds This gives you time to close and lock the front cover of the Outdooree R5 and then walk away During this time the motion indicator LED will blink red continuously After it stops blinking t2. of sight 3 In some cases setting the camera near water will make the camera take images with no subject in them Try aiming the camera over ground 4 Try to avoid setting the camera up on small trees that are prone to being moved by strong winds 5 Remove any limbs which are right in front of the camera lens PIR Sensor LED Flashes Doesn t Flash 1 When the camera is in the SETUP mode a special LED on the front of the camera will flash when it senses motion This is for setup 39 purposes only and will help the user aim the camera 2 During use the LED will not flash when the camera takes an image This is to help keep the camera hidden from game Camera won t retain settings 1 Make sure that you have been saving the changes to any parameter settings that you made while in SETUP mode by pressing OK after changing the setting If you dont save your new setting after changing it the camera will continue to use the original default setting for that parameter 40 10 Technical Specifications Image Sensor 5 Megapixel Color CMOS Maximum Pixel Size 2560x1920 5MP Lens F 3 1 FOV 50 Auto IR Cut Remove at night IR Flash Range 36 45 12m 15m Memory Card SD or SDHC Card Maximum capacity 16GB Internal RAM 32MB Picture Size SMP 2560x1920 3MP 2048x1536 Video Size 720x480 30fps 640x480 30fps 320x240 30fps PIR sensitivity PIR with 3 sensitivity levels Hi
3. set the date and time when necessary e g after every battery change The format of the date is month day year while the time format is hour minute second In MENU state the steps as following a D G Press the LEFT arrow button until Set Clock appears at the top of the screen Press OK Use UP and DOWN buttons to change the current hour Use RIGHT arrow to move highlighted box to minutes Use UP and DOWN buttons to change the current minute Use RIGHT arrow to move highlighted box to year Use UP and DOWN buttons to change the current year Use RIGHT arrow to move highlighted box to month Use UP and DOWN buttons to change the current month 16 j Use RIGHT arrow to move highlighted box to day k Use UP and DOWN buttons to change the current month Press OK to save settings After the settings of the date and time press the OK key to save them or the MENU key to cancel setting 4 4 Set time stamp This parameter defines whether the time should be stamped in the pictures and video clips or not a Press the LEFT arrow button until Time Stamp appears at the top of the screen b Use UP and DOWN arrows to choose On or Off On will place the date and time on the lower portion of all pictures and the first frame of videos c Press OK key for saving setting or MENU key for cancelin
4. the MENU button Press the LEFT arrow button until capture number appears at the top of the screen Use the UP and DOWN arrows to choose the number of images 7 2 or 3 you want taken during each activation 21 Press OK key for saving setting or MENU key for canceling operation and exiting 4 12 Set Image resolution Press the MENU button Press the LEFT arrow button until Image size appears at the top of the screen Use the UP and DOWN arrows to choose the image size you want 3M is low resolution 5M is high resolution Press OK key to save the current setting or MENU key for canceling the setting and quitting Mounting and positioning your camera After you ve programmed the camera s setting to your personal preferences youre ready to take it outside and slide the power switch to ON When setting up the Outdooree R5 for scouting game or other outdoor applications you must be sure to mount it in place correctly and 22 securely We recommend mounting the Outdooree R5 on a sturdy tree with a diameter of about 6 12 inch To get the optimal picture quality the tree should be about 10 20 feet away from the place to be monitored with the camera placed ata height of 2 5 feet Keep in mind that you will get the best results at night when the subject is within the ideal flash range no farther than 45 and no closer than 6 from the camera There are two ways to mount the
5. you format an SD card for the Outdooree R5 in your computer you should choose the file system format FAT16 Normally FAT16 is recommended unless you have another image viewer that uses FAT12 or FAT32 format e DOWNLOADING the PHOTOS and VIDEOS To download your photos videos to a PC or Mac first make sure the Outdooree R5 power switch is in the OFF position Connect the supplied cable to the camera s USB port then directly to a main USB port on your computer do not use front panel keyboard USB ports or unpowered hubs The Outdooree R5 will be recognized as a standard USB Mass Storage device this may take several seconds the first time you connect it If you would rather leave your camera in the woods and just pull its SD card out an SD card reader works the same way as described in this section once the card is inserted and the reader is connected to your computer With Windows XP or later you can then simply use the options in the pop up window to copy view or print your photos right On all Windows OS the Outdooree R5 will also be listed as a Removable Disk if you open the My Computer window on Macs an icon will appear on your desktop The Outdooree R5 photo files are named PICT0001 JPG etc and are located in the DCIM 100EK113 folder on this Removable Disk Video file names will end with ASF or AVP You may copy the photos videos to your hard drive as yo
6. ETTING OK Repl Up Video K napay Left lt Right Shot Down Camera Fig 2 Motion Low battery indicator IR LED s Fig 3 Fig 4 Locking tabin 7 unlocked position www outdooree com Image Size Battery Power Camera Mode Date Time The Number Captured Fig 5 The Number Can Be Captured aie Introduction The Outdooree R5 is a digital scouting surveillance camera which uses a highly sensitive Passive Infra Red P R motion sensor to detect heat and movement and then take high quality pictures up to SMP still photos or video clips The Outdooree R5 consumes very little power less than 300UA in a standby surveillance 4 state This means it can deliver up to six months stand by operation time when the device is powered by eight AA alkaline batteries Once motion in the monitored area is detected the digital camera unit will be triggered in approximately 1 second and then automatically take photos or videos according to previously programmed settings The Outdooree R5 is equipped with built in infrared LEDs for night time illumination so that it delivers clear photos or videos in black amp white even in the dark and it can take color photos or videos under sufficient daylight The Outdooree R5 is designed for outdoor use and is completely weatherproof 2 Parts and Controls Identification a Packing Contents The following items are included with your new Outdoore
7. Outdooree R5 A Digital Infrared 5MP Scouting Surveillance Camera User s Manual TD INTFOGUGUON Sos baci cast Suan sh ces aa 4 2 Parts and controls ID cccecseeeeeeeeeeeeeeeees 5 3 Installing Batteries and SD Card ccecseeeeees 7 4 Using and Programming the Outdooree R5 11 4 1 Set Camera Mode ccscceeeeeeeneees 14 4 2 Restore Factory Default Settings 15 4 3 Set CloCK assisnnnnrecussanaaneennsunnennnannan 16 4 4 Set time Stamp cceeseeseeeeeneeneenes 17 4 5 Set TV QUPUT sro eee 18 4 6 Format SD Card cccceeceeeeeeeeeees 18 4 7 Set Sensitivity level ccceceeeeeeeees 19 4 8 Set Interval cc iesicn coi iaiicsiiewdcsiciceiens 19 4 9 Set Video Length scceeseeeeeeees 20 4 10 Set Video Resolution cccsecseees 21 4 11 Set Burst Mode Capture Number 21 4 12 Set Image Resolution scssccesees 22 5 Mounting and Positioning your camera 22 6 Sensing Angle and Distance test 000 23 7 Switching ON the CaMesa ccsseeeceseseeeenseeeeeees 25 8 Playing back deleting photos video 25 9 Trouble SHOOting FAQ S ssecsseessseeessseeeeeseees 32 10 Technical Specifications ccccseeseeeee 41 Fig 1 External DC Power In Keyboard Port a USB Port r MADEJ IN CHINA SN f0106072 TVOut SD Card Slot Power Switch REMOTE CONTROL CAMERA S
8. and time so the camera will imprint them on your photos as they are taken learn how to set the camera to shoot video clips instead of still photos if you like and read some tips about mounting it on a tree a THE OFF ON AND SETUP MODES The Outdooree R5 has three basic operational modes OFF mode Power switch in the OFF position ON mode Power switch in the ON position without Keyboard being connected SETUP mode Power switch in the ON position with keyboard being connected b OFF mode The OFF mode is the safe mode when any actions must be taken e g replacing the SD card or batteries or transporting the device 12 You will also use OFF mode if you connect the camera to a computer s USB port later c ON mode Anytime after the batteries and SD card have been inserted you can switch on the camera When the power switch is moved to the ON position the camera will enter into the ON Live mode The motion indicator LED Fig 3 will blink red for about 10 seconds This interval allows time for you to close the Outdooree R5 s_ front cover lock it and leave the monitored area Once in the ON mode no manual controls are needed or possible The Outdooree R5 will take photos or videos automatically according to its current parameter settings when it is triggered by the PIR sensor s detection of activity in the area it covers 13 d SETUP mode In anytime in the ON mode the SETUP mode is activat
9. appear too light at closer distances d Daytime photos or videos appear too bright 1 Make sure that the camera is not aimed at the sun or other light sources during the day Photos with streaked subject 1 In some cases with low lighting conditions and fast moving subjects the 5MP or 8MP resolution settings may not perform as well as the 3MP setting 2 If you have multiple images where fast moving subjects produce streaks on the photo try the 3MP setting instead Red green or blue color cast 1 Under certain lighting conditions the sensor can become confused resulting in poor color images 2 If this is seen on a consistent basis then the sensor may need servicing Please contact Outdooree customer service Short video clips not recording to the length set 1 Check to make sure that the SD card is not full 2 Make sure that the camera has good batteries in it Near the end of the battery life the camera may choose to record shorter video clips to conserve power Date Time Stamp not appearing on images 1 Make sure that the Time Stamp parameter is set to On Photos Do Not Capture Subject of Interest 1 Check the Sensor Level PIR sensitivity parameter setting For warm environmental conditions set the Sensor Level to High and for cold weather use set the sensor for Low 2 Try to set your camera up in an area where there is not a heat source in the camera s line
10. e opening the inside cover You will see the battery compartment The Outdooree R5 has eight battery slots Starting from the left of the battery compartment slots 1 2 3 and 4 form one group while slots 5 6 7 and 8 forms the other group each providing 6 volts in parallel For maximum battery life you should install a full set of eight batteries The Outdooree R5 7 may also be operated by just four batteries installed in the top group only starting at slot 1 Battery life will be shorter with 4 batteries but the camera will operate normally Whether you use 4 or 8 be sure to insert each battery with correct polarity negative or flat end against the long spring of each battery slot Outdooree recommends using eight new lithium AA or alkaline AA batteries NiMh Rechargeable batteries can also be used but they might have a shorter life span due to their reduced efficiency over time and at low temperature b Using an External Power Source optional user provided Optionally you can connect an external 6V DC power source to the DC In jack at the bottom of the Outdooree R5 It is recommended to use a power source with a current output greater than 1000mA However during bright daytime operation when no flash is required the Outdooree R5 can function with much less current gt 400mA Please use a compatible 8 power source cable not provided to connect the external DC power source with the power inpu
11. e protect switch on the card is in the up off position when looking at the front of the card the switch is on the left side of the card fig 4 The following describes how to insert and remove the SD card e Insert the SD card into the card slot with its label side upwards see above A click sound indicates that the card is installed successfully If 10 the wrong side of the card is facing up you will not be able to insert it without force there is only one correct way to insert cards Formatting the SD card by using the Outdooree R5 Format parameter before using it for the first time is recommended especially when a card has been used in other devices see 4 6 Format SD Card for details e To take out the SD card just gently push in the card do not try to pull it out without pushing in first The card is released from the slot and ready to be removed when you hear the click 4 Using and Programming the Outdooree R5 Once you ve prepared your Outdooree R5 by properly installing batteries and a SD card you could simply take it outside strap it to a tree switch it on and leave The camera will function in the factory default settings However we highly recommend that you first spend some additional time indoors with this manual and your camera until you know a bit 11 more about what the 2 way work state and those Keyboard keys do If nothing else you ll probably want to at least set the date
12. e R5 Keyboard USB cable TV cable and attachment strap b Controls The Outdooree R5 provides the following connections for external devices Keyboard Port USB port SD card slot TV Out and external DC power in Fig 1 Remote Control Remote Control is a keyboard for setting Outdooree R5 s parameters The keyboard interface with six keys is primarily used in SETUP mode to select operational functions and parameters As shown in Fig 2 these keys are UP DOWN LEFT RIGHT OK and MENU Four of the keys can also perform a second function in addition to their main function The DOWN key can be used to set the camera to Photo mode still camera icon and the UP key can set the camera to Video mode movie camera icon The RIGHT key also serves as the manual shutter SHOT button of the camera and the OK key switches the camera to the Playback REPLAY mode These secondary functions are indicated by icons or text above the key as shown in Fig 2 3 INSTALLING THE BATTERIES and SD CARD Before you begin learning how to use your Outdooree R5 you will first need to install a set of batteries and insert an SD card Although that may only take you a minute there are some important notes about both batteries and SD cards you should be aware of so please take the time to read the following directions and cautions a Loading Batteries After opening the Outdooree R5 Casing by Sliding the bottom cover to the right sid
13. ed when connecting the keyboard with the Outdooree R5 In OFF mode you just need connect the keyboard with Outdooree R5 and power on the Outdooree R5 if the SETUP mode is needed Under the SETUP mode you can take over the control of the Outdooree R5 manually or set operational parameters with the help of a display i e the built in LCD 4 1 Set Camera mode video or still images Enter into SETUP mode first Two ways for setting this parameter One is to use the shortcut key and the other is through the MENU With the shortcut key set camera mode to video by pressing the UP key and set camera mode as camera by pressing the DOWN key With MENU Way Press the MENU button Press RIGHT button till Mode appears this 14 parameter has two values camera and video Pressing UP key can switch between these two parameters Press OK key to save setting or MENU key to cancel setting and exit Please note you ll quit the parameter setting without any saving and no parameter is changed if you press the MENU key at any time before pressing OK key 4 2 Restore Factory Default settings a Note Restoring the factory default settings will remove any previous settings you have saved b Enter into SETUP mode Press the MENU button c Press the RIGHT or LEFT key till the Default appears Push the OK key to load default settings or MENU key to cancel this operation 15 4 3 Set Clock You can
14. ey for saving setting or MENU key for canceling operation and exiting 4 8 Set Interval Note The interval setting controls how often the camera can trigger i e a 1 minute 19 interval will cause the camera to only trigger every 1 minute even if there are animals present This allows the user to eliminate unnecessary pictures a b C Press the MENU button Press the LEFT arrow button until Interval appears at the top of the screen Use the UP and DOWN arrows to choose the interval you want There are interval settings ranging from 1 second to 60 minutes Press OK key for saving setting or MENU key for canceling operation and exiting 4 9 Set video length Press the MENU button Press the LEFT arrow button until video length appears at the top of the screen Use the UP and DOWN arrows to choose the video length you want There are 56 video length settings ranging from 5 seconds to 60 seconds Press OK key for saving setting or MENU key for canceling operation and exiting 20 4 10 Set video resolution Press the MENU button Press the LEFT arrow button until video size appears at the top of the screen Use the UP and DOWN arrows to choose the video size you want 320x240 is low resolution 720x480 is high resolution Press OK key to save the current setting or MENU key for canceling setting and exiting 4 11 Set burst mode capture number Press
15. g operation and exiting 17 a C 4 5 Set TV output Press the LEFT arrow button until TV Output appears at the top of the screen In the US Canada Mexico Asia and South America TV s are formatted to NTSC European countries use PAL Use the UP and DOWN arrows to select the appropriate TV Output Press OK to save setting 4 6 Format SD card Note Formatting the SD card will erase all data stored on the card Do not format if there is important data stored it will be unrecoverable Note Formatting is highly recommended if you are using an SD card that has been used in other electronic equipment such as point and shoot style cameras a Press the LEFT arrow button until Format appears at the top of the screen b Press OK C Use the UP and DOWN arrows to select Yes 18 d Press OK a green screen will appear that says Format Success and then the screen will return to the format screen 4 7 Set sensitivity level Note The sensitivity level dictates how easily the camera triggers It is recommended to use Low sensitivity during winter months to avoid false triggers High for hot summer Normal for spring and fall season a Press the LEFT arrow button until Sensor Level appears at the top of the screen b Use the UP and DOWN arrows to select Low Normal or High c Press OK k
16. g the Camera to a Computer You can always un mount the entire camera from the tree and connect its USB port to a 28 computer It will be recognized as a removable disk without the need to install any drivers or software When using a PC or Mac to view photos or video clips first connect the device to the computer with the supplied USB cable Then use commercial software with an image browser feature or an image browser included with the PC s operating system to view images saved on the SD card in the folder DCIM 100EK113 Each new image or video will be numbered incrementally in order of the time it was captured For example you will see file names such as PICT0001 JPG Through the file format suffix you can distinguish whether the file is a still photo with suffix jog or a video Video files may require additional software for viewing on a Mac The Outdooree R5 supports 3 kinds of file system formats FAT12 FAT16 and FAT32 The default value is FAT16 to save photos and videos Here are some related notes 29 e You dont need to be concerned about the file system format of the Outdooree R5 unless your equipment has problems reading the SD card If this happens please format the SD card with the Outdooree R5 or in your computer first and then insert the card into your Outdooree R5 and try again e The default file system format of the Outdooree R5 is FAT16 which most computers can read If
17. gh Normal Low Operation Day Night Response Time 1s Triggering Interval 1 sec 60min programmable Shooting Numbers 1 3 programmable Video Length 5 60sec programmable Power Supply 8xAA recommended 4xAA as emergency power Stand by Current lt 0 3mMA lt 7mAh day Power Consumption 200mA 530mA when IR LED lighted User Interface LCD display Interface TV out NTSC PAL USB SD card holder 6V DC external Security Strap 1 4 20 attachment Operating Temperature 20 60 C Storage temp 30 70 C Operating Humidity 5 90 Security authentication FCC CE RoHs WEEE Fe C 41 8 9 OUTDOOREE R5 WARRANTY REGISTRATION FORM customer name Address Province State and country Post code Zip code Daytime Phone Email Model Outdooree R5 Serial Number Date purchased 10 Purchased from Note A Fill out the above form as your record Then Email the form content or this page photo to Info Outdooree com or Register online at www Outdooree com B OUTDOOREE provides a 1 year warranty with this product against manufacturing defects or workmanship if your camera fails to function under normal use within the 1 year time frame OUTDOOREE will repair or replace the camera with no charge Improper use of the camera resulting in damage is not covered by this warranty OUTDOOREE can service your camera after the 1 year warranty has expired but t
18. he PIR is active and any motion that is detected by it will trigger the capture of photos or videos as programmed in the SETUP Menu 8 PLAYING BACK DELETING __the PHOTOS VIDEOS After you have setup mounted and activated your Outdooree R5 you will of course be eager to return later and review the images it has captured for you a Reviewing Images on an External Video Monitor 25 A TV monitor can also be used to play back pictures or videos from the device Connect a TV monitor or a viewing device such as a digital picture frame that has a standard composite video input RCA jack to the Outdooree R5 s TV Out mini jack using the supplied cable Then Entering into SETUP mode Press the OK key The most recently captured image will be shown on the video monitor For video clips press the SHOT RIGHT key to start playing press again to stop Press the UP key for the previous photo or video and the DOWN key for the next one When viewing images the total number of all images in the SD card and the index of the displaying image are shown in the center of LCD and at the bottom of the video monitor respectively Press the OK key to return to live preview state SETUP mode when playback is finished 26 b Deleting Photos or Videos lf you see a photo or video during playback on video monitor that you want to delete it can be done easily without leaving SETUP mode Press the MENU key You wi
19. he customer will be responsible for parts labor and shipping costs Outdooree R5 Extra small size 5 1 4Hx31 44Wx21 8D 22 High intensity Infrared LED s with a 33 range and 40 degree dispersion angle PIR Motion Sensor with adjustable sensitivity Ultra low stand by current extending battery life Operates on 4 or 8 AA batteries not included Wired remote control for easy programming Accepts SD memory cards up to 16GB 1 sec to 60 min programmable delay 5 sec to 60 sec programmable video length Fast 1 second trigger speed Records still pictures or video 3MP or 5MP picture size adjustable Operates from 4F to 140F 20 C to 60 C Weather resistant 1 year limited warranty for more info visit www outdooree com Outdooree R5 camo 5 0010 Made in China Imported by Import par Outdooree Industrial LTD Fabriqu en Chine Toronto Ontario M1W 3W2 8 5535 101
20. ll see the first Delete screen which lets you selects the option to delete only the currently displayed photo video or all photos videos see below Highlight the Delete Current or Delete All option then press OK Next select Yes and press OK to erase only the last displayed photo or video if you selected Delete Current or every photo and video file on the card if you selected Delete All or select No and press OK to cancel the operation without deleting any files NOTE after deleting a picture or a video file the deleted files can t be restored It is also possible to delete all files from the card by using the Format parameter See 4 6 Format SD Card 27 c Reviewing Images _ Directly From the SD Card This is the most popular method of viewing images Since un mounting the camera and taking it to your computer isnt very convenient you may find it easier to just take the card out By removing the SD card swapping it for a new empty card if you like and taking it to your home or campsite to view the images by using an SD card reader user Supplied connected to your computer some computers and TVs have a built in SD card slot you can leave the camera in place ready to capture more images Once connected the card reader works the same way as described below please read that section if you have any problem finding your files d Reviewing Images by Connectin
21. nce indicates that poor quality SD cards can sometimes reduce your Outdooree R5 s battery life Camera stops taking images or won t take images 1 Please make sure that the SD card is not full If the card is full the camera will stop taking images 2 Check the batteries to make sure that they are new alkaline or lithium AA batteries See note above about short battery life 3 Make sure that the camera power switch is in the ON position and not in the OFF or SETUP modes 4 Make sure that you are using a good quality SD card in your camera We recommend Outdooree or Sandisk brand SD Cards 5 If the SD card has its write protect switch in the lock position the camera will not take images 6 If you have used an SD card in another device before inserting it in your Outdooree R5 you should try formatting the card using the Format parameter in SETUP mode make sure you have backed up any important files first as formatting will erase all previous files See 4 6 Format SD Card In some cases other devices may change the formatting of the SD card so that it will not work properly with the Outdooree R5 Camera won t power up 1 Make sure that you have installed at least 4 batteries the required minimum in the battery compartment starting at the top filling battery spaces 1 4 with no gaps We recommend using 8 new alkaline or lithium AA batteries in all Outdooree R5 cameras 2 Make sure tha
22. t jack of the Outdooree R5 making sure that the polarity is correct Note The power connector is a 4 0x1 7mm coaxial DC power plug with positive tip inside pin polarity Radio Shack P N 274 1532 or equivalent If both an external power source is connected and batteries are installed the Outdooree R5 will be powered by the external power source When the batteries become weak the low battery indicator LED will glow blue indicating the batteries should be changed c Inserting the SD Card Warning Be sure the cameras power switch is turned off before installing batteries or SD The Outdooree R5 has 32MB of internal memory which can hold only about 25 photos 5MP resolution This is handy for testing and getting familiar with the camera but you 9 will no doubt want to leave the camera unattended for longer than a day so using an SD card is recommended Insert the SD card with the camera s power switch in the OFF position before beginning to operate the camera Do not insert or remove the SD card when the power switch is in the ON position The Outdooree R5 uses a standard SD Secure Digital memory card to save photos in jog format and videos SD and SDHC High Capacity cards up to a maximum 16GB Capacity are Supported Outdooree recommends using Outdooree or Sandisk brand SD cards Before inserting the SD card into the card slot after opening the camera s front cover please make sure that the writ
23. t the batteries are installed correctly observing proper polarity Always place the negative flat end of each battery in contact with the long spring side of its slot inside the camera 3 After moving the switch from OFF to ON make sure that the switch is correctly in position to ensure the proper mode avoid positions between two modes Still Photo and or Video Quality Problems a Night photos or videos appear too dark 1 Check the battery indicator icon to see if battery power is full The flash will stop operating near the end of the battery life 2 You will get the best results when the subject is within the ideal flash range no farther than 45 14m from the camera Subjects may appear too dark at greater distances 3 Please note that when the Capture Number parameter is set higher than 1 Photo or with very short Interval settings some images may appear darker than others due to the quick response and rapid retriggering of the camera allowing less time for the flash to fully recharge before firing again b Daytime photos or videos appear too dark 1 Make sure that the camera is not aimed at the sun or other light sources during the day as this may cause the auto exposure to produce darker results c Night photos or videos appear too bright 1 You will get the best results when the subject is within the ideal flash range no closer than 3m from the camera Subjects may
24. u would any file just copy paste or drag the file names or icons to your drive or desktop After the photos are copied to your hard drive you can disconnect the Outdooree R5 On Mac computers drag the disk that appeared on your desktop when the camera was connected into your Trash to eject it before disconnecting The jog standard files from the Outdooree R5 may be viewed and edited with any photo software you choose to use The video files may be viewed with Windows Media Player version 7 or later as well as other video playback programs that may have been supplied with your computer or are available online Video files may require additional software for viewing on a Mac 9 Trouble shooting FAQ Battery life is shorter than expected 1 Battery life will vary slightly with operating temperature and the number of images taken over time Typically the Outdooree R5 will be able to capture several thousand images before the batteries die 2 Check to make sure you has used new alkaline or lithium batteries Outdooree recommends using 8 new alkaline or lithium AA batteries in all Outdooree R5 cameras to obtain maximum battery life 3 Make sure that the power switch was turned to the ON position and that the camera was not left in SETUP mode while in the field 4 Make sure that you are using a good quality name brand SD card in your camera We recommend Outdooree or Sandisk brand SD Cards Our experie
Download Pdf Manuals
Related Search