USER`S MANUAL
Contents
1. CONTROLLING THE ZOOM AND FOCUS RINGS 2 CONNECT THE VIDEO AND POWER CABLES How to connect 1 Single system f AC 24V POWER DC 12V 2 Multiple Camera System AC 24V POWER DC 12V AC 24V POWER DC 12V AC 24V POWER DC 12V Description of operation wiring diagram 3 DVR system AC 24V POWER DC 12V AC 24V POWER DC 12 AC 24V POWER DC 12V AC 24V POWER DC 12V lt AC 24V POWER DC 12 5 1 LED BRIGHTNESS VOLUME 2 IRLEDS 3 DC AUTO IRIS LENS 5 50 mm 1 LED BRIGHTNESS VOLUME CONTROLL THE BRIGHTNESS OF LED 2 IR LED S INFRARED LED S ACTIVATE AS NEEDED 3 DC AUTO IRIS 5 50MM ADJUST BETWEEN T lt gt W TELE lt gt WIDE TO SET THE FIELD OF VIEW FOCAL LENGTH SET THE FOCUS BY ADJUSTING gt N NOTE BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED INTO POSITION THROUGH THE USE OF SET SCREWS REAR SWITCHES 1 VIDEO TEST TERMINAL 2 DC IRIS LEVEL 3 V PHASE 4 FUNCTION DIP SWITCH 5 LUX DIP SWITCH REMOVE THE REAR COVER SCREWS TO GAIN ACCESS 1 VIDEO TEST TERMINAL ALLOWS THE CONNECTION OF A LOCAL MONITOR TO MAKE INITIAL ADJUSTMENTS TO THE CAMERA 2 DC IRIS LENS LEVEL FINE TUNE THE AUTO IRIS LENS 3 V PHASE LEVEL WHEN DESIRED THE VERTICAL PHASE MAY BE ADJUSTED TO SYNCHRONIZE THE VERTICA2. L PHASE OF THE CAMERA WITH OTHER CAMERAS IN THE SYSTEM THIS FEATURE IS ONLY AVAILABLE IN 24 VOLT AC OPERATION SWITCHES Default setting The Function selection switch is factory set as below 4 Function DIP SWITCH 5 LUX DIP SWITCH REAR SWITCHES Switch Mode Function DIP SWITCH 1 ELC Electronic Light Compensation ON Camera is in Electronic Shutter Mode OFF Electronic Shutter is fixed at 1 60 and Auto Iris mode is active SWITCHES 2 BLC Back light compensation If there is a strong light behind an object the object may appear as a shadow Activating the BLC will minimize this effect The Coverage of the BLC is center plus bottom as below 3 F L Flicker Less F L ON OFF FUNCTION ON Use when the lux changes often OFF Use under normal circumstances 4 L L Line Lock L L ON OFF FUNCTION Locks the camera to the 60 Hz of the wall outlet Only operates in the 24 Volt AC mode REAR SWITCHES LUX DIP SWITCH LUX DIP SWITCH Tells the camera when to switch to the B W night mode Note Only one switch can be in the on position ata time 1 The camera will switch at 1 2 lux 2 The camera will switch at 1 lux 3 The camera will switch at 3 lux 4 The camera will switch at 5 lux SPECIFICATION IMAGE SENSOR 1 3 SONY EX VIEW CCD SUPER HAD CCD TV SYSTEM
3. NTSC PAL SCANNING SYSTEM 2 1 INTERLACE SYNC SYSTEM LINE LOCKED ADJUSTABLE V PHASE LINE LOCK INTERNAL RESOLUTION 270K 420 LINES 410K 480 LINES MINIMUMILLUMINATION 0 1 LUX SH 0 03 LUX EX IR OFF 0 00 LUX IR ON PHOTO CELL PHOTOCONDUCTIVE CELLS ADJUSTABLE S N RATIO MORE THAN 60dB VIDEO OUTPUT 1 0 Volt p p 75 ohm COMPOSITE ELECTRONIC SHUTTER NTSC 1 60 to 1 100 000 sec PAL 1 50 to 1 100 000 sec POWER REQUIREMENTS DUAL VOLTAGE 24 VOLTS AC amp 12 VOLTS DC POWER CONSUMPTION 600 mA LENS DC AUTO IRIS VARIFOCAL LENS 5mm 50mm OPERATIONAL TEMPEATURE 20 deg F to 122 deg RH 95 STORAGE TEMPEATURE 30 deg F to 140 deg F WEIGHT 1900 grm VER 060901 This manual is based the date shown the right and specifications are subject to Change without notice for quality improvement
4. USER S MANUAL IR DAY NIGHT CAMERA DC 5 50mm LENS WEATHERPROOF BUILT IN LEDS 8 PHOTO CELL ALL CONTROLS ARE EXTERNAL ALLOWING THE CAMERA TO REMAIN FACTORY SEALED SPLIT GLASS TECHNOLOGY AVOIDS IR REFLECTIONS VIDEO COLOR CCD CAMERA PRECAUTIONS PRODUCT FEATURES CAMERA INSTALLATION FOCUSING DESCRIPTION OF OPERATION 6 7 CAMERA PARTS REAR SWITCHES DIMENSION SPECIFICATION WARRANTY 5 DC 5 50mm version 1 CAMERA 1 SUNSHIELD ACCESSORIES 4 MOUNTING SCREWS 1 STAND CONTROL WRENCH 1 2 6 WRENCH FOR BACK COVER 1 1 25 WRENCH FOR ZOOM amp FOCUS 1 VIDEO TEST CABLE 1 POWER CABLE PRECAUTIONS INSTALLATION SHOULD BE PERFORMED BY QUALIFIED PERSONNEL PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR 12 VOLT DC POWER SUPPLY PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE TO PREVENT FIRE OR ELECTRICAL SHOCK PLEASE INSURE THAT YOUR INSTALLATION AREA CAN SUPPORT THE WEIGHT OF THE CAMERA PLEASE HANDLE THIS CAMERA CAREFULLY USE A STRONG OR ABRASIVE DETERGENT WHEN CLEANING THE CAMERA USE A SOFT TISSUE OR LENS CLOTH TO CLEAN THE FRONT GLASS EXPOSE THE CAMERA TO DIRECT SUN PRODUCT FEATURES Weatherproof sunshield Rear panel controls BLC ELC F L L L Dual Voltage operation 1 3 Sony CCD Turbo AGC External lens control of zoom and f
5. ocus Split glass technology eliminates IR reflections Video test connector for easy installation Lux level dip switch for day night functions UTP terminal built in for use with twisted pair wiring Note specifications are subject to change without notice CAMERA INSTALLATION CONNECTIONS 1 WHEN USING 12 VOLTS DC constant voltage 600 mA CONNECT POWER TO THE DC JACK POWER INPUT RED connect CENTER 2 WHEN USING 24 VOLTS AC CONNECT ACCESSORY CABLE TO THE DC JACK AND CONNECT AC 24V TO THE LEAD POWER INPUT RED connect 8 gt 24V NTER 3 CONNECT VIDEO CABLE CABLE TO THE JACK YELLOW VIDEO OUT NOTE ALL CONNECTIONS MADE DIRECTLY TO THE PCB IF DESIRED 4 OPTIONAL USE OF UTP OUTPUT ALLOWS USE OF THE CAMERA WITH CAT 5E OR UTP CABLE A RECEIVING BALUN MUST BE USED ON THE MONITOR SIDE PLEASE SEE OUR MODEL VID UTP UTP CABLE FOCUSING VIDEO COLOR CCD CAMERA 00 FOCUS CONTROLLER ZOOM CONTROLLER 1 SET THE FOCUS BY USING THE FOCUS CONTROLLER 2 SET THE ZOOM OR FIELD OF VIEW BY USING THE ZOOM CONTROLLER 5 50mm 3 LOCK BOTH RINGS INTO POSITION USING THE SET SCREWS Description of operation wiring diagram How to operate 1 SET THE DISTANCE AND FOCUS BY
Download Pdf Manuals
Related Search