pdf/manuals/Majestic TM154 Manual
Contents
1. to _ 3 Replace the battery compartment cover MAJESTIC WW Y Install two high quality 1 5V AAA alkaline batteries Don t mix old batteries with new batteries Remove batteries when you won t use the remote controller for long time Liquid leakage from old batteries may cause operation failure E Notes for using remote controller e Make sure there are no objects between the remote controller and its sensor e Don t place the remote control near a heater or in damp place Strong impact to the remote control may cause operation failure e Signal from the remote control may be disturbed by sun light or other bright light In this case darken the room or move the TV Basic Operation Turning the TV On and Off Standby Setup The AC DC adapter and the AC power cord must be set up and connected to have the TV in standby mode ready to be turned on Press the ON OFF button on the front panel of the TV to go into standby mode 1 If the TV is in standby mode press the POWER button on the remote controller or the TV itself to turn the TV on 2 Press the Power button again on the remote controller or the ON OFF button the TV itself to turn the TV off Note If the TV is on and the POWER button is pressed to turn the TV off the TV goes into standby mode Programme selection You can select a Programme number with the PRa w button or NUMBER buttons Volume adjustment Press the VOL lt b butto2. Press the PR v button to select Off Time Radio Name Edit ___ Then press the VOL lt p gt Radian a button repeatedly to select Off 5 10 30 Station P01 3 ae 11 Press the PR v button to select Edit Name Adjust 4 av Confirm OK Then press the VOL lt p gt _ Back MENU Exit TWAV button to edit radio name You can assign a radio name with 8 characters Press the PR v button repeatedly You can use the numeric 0 to 9 the alphabet A to z capital and small letters and a blank With the VOL lt b button you can select in the opposite direction 13 Press the MENU button to return to prior menu Press the TV AV button to exit Then the radio setting condition is displayed 12 Radio Setup Mode Auto Frequency 87 5 MHz Programme MEM 1 Delete Memorize Auto Programme gt Off Time off Edit Name gt Station Name Position av Adjust lt gt Exit TV AV SSM PCI ARC SIZE HOLD INDEX TIME REVEAL MIX TELETEXT TEXT On Off 1 Press TEXT button once displays the Teletext pages 2 Press MIX button once more displays the Teletext pages superimposed on the TV picture 3 Press the TEXT button to switch off Teletext once more Text mode is off and TV mode appears TOP text The user guide displays four fields red green yellow and blue at the bottom of the screen The yellow field denotes the next gr
3. e Mild Softer Picture Appearance e Game External Video Game Picture Setup e User Manual Picture Setup Note In the PC mode PSM function isn t available Sound Control You can select your preferred sound setting Flat Music Movie or Speech You can also adjust the sound Sound frequency of equalizer balance If you switch AVL to on Equalizer gt the set automatically keeps on an equal volume level even Balance 0 if you change programmes AVL Off Surround Off 1 Press the MENU button 2 Select the Sound menu 3 Press the PRA v button to select the desired sound item Equalizer Balance AVL Surround or Sound Mode 4 Press the VOL lt p gt button to make desired adjustment in 5 Press the VOL lt p button in Equalizer to set the R WER X Sound Mode Position av Next lt gt Back MENU Exit TV AV Equalizer O E E OOO Flat He CD Movi z e O User 0105 15 5 0 10KHz O MENU TV AV Position ay Back MENU Exit TV AV 6 Press the PRa v button to select your preferred setting Flat Music Movie Speech or User To set the Equalizer User a Select User by pressing the PR v button b Select a sound band by pressing the VOL lt gt button c Make appropriate sound level with the PRa v button d Press the MENU button to return to preceding menu 7 Press the PR v button to the Balance menu 8 Select the Ba
4. 1 AC DC adaptor 2 AC Cord 6 PC IN cable 7 PC Audio IN cable gt lt Controls Front Panel MENU WPRA 4VOL gt TVIAV Poba 1 MENU Displays a menu 2 PR Programme Up Down Selects a programme or a menu item 3 Power Indicator Illuminates in red when the TV is in standby mode Illuminates in green when the TV is switched on Illuminates in blinked when the power save mode only PC mode 4 Remote control sensor Accepts the IR signal of remote controller 5 ON OFF Switches TV set on or off 6 VOL Volume Up Down Adjusts the volume Adjusts menu settings 7 TV AV Selects TV COMPONENT VIDEO RADIO Only when the set is Radio On or PC mode Clears the menu from the screen Rear Panel 3 4 if i ANN ANT PC ANALOG aaa A 2 ae R HIP VIDEO L MONO R L 66 666 1 DC12V IN 2 PC ANALOG IN 3 PC AUDIO IN Connect the audio cable from the PC AUDIO IN of the set 4 COMPONENT IN 5 HEADPHONE OUT Connect a headphone to this socket 6 A V IN Connect the Audio Video outputs of external equipment to these inputs 7 ANT Antenna input Controls All the functions can be controlled with the remote controller Some functions can also be adjusted with the buttons on the side panel of the set Remote controlle
5. B Clock Main Menu Picture Clock i e Contrast 90 Off Time E _ _ Off Picture gt Brightness 75 A Sound gt Golour 75 On Time Off Special gt Sharpness 60 On Programme 1 Setup gt Position av Adjust lt gt Position av Next 4 gt Position av Adjust 4 Back MENU Exit TV AV Exit TWAV _Back MENU Exit TV AV k z m Auto Programme L_ System BG gt Sound Start Equalizer gt Balance 0 AVL Off Position av Adjust lt gt Surround Off Back MENU Exit TV AV Sound Mode ee Manual Programme Position av Next 4 gt x it Programme 1 Back MENU Exit TV AV Channel 69 Table V UHF System BG Memorize Name A A Special Position av Adjust lt gt VOL VOL gt Back MENU Exit TV AV Clock gt PRY Blue Back off 0 o Auto Sleep off Programme Edit Childlock Off POO 5 R Radio Off Polcas O A A Output Frequency 87 9MHz P02 SE HOAD INDEX Position av Next 4 gt E A Back MENU Exit TV AV TIME REVEAL MIX Delete ciie Position av 4 Back MENU Exit TV AV Setup f Language English Auto Programme Deutsch Manual Programme Frangais Programme Edit Espanol Language Italiano Nederlands Portugu s Position av Next lt gt Position av Back MENU Exit TV AV Back MENU Exit TV AV Setting up TV Programme Once you have preset the programmes you will be able to use the PRA v or NUMBER buttons to scan the programmes yo
6. directly enter the programme number with the NUMBER buttons or select it in the programme edit Picture Control You can adjust picture Contrast Brightness Colour Sharpness and Tint only in NTSC mode to the levels you prefer Picture Contrast 90 Brightness 75 Colour 75 Sharpness Manual Picture Control 1 Press the MENU button 2 Select the Picture menu 3 Press the PRa v button select a picture item 4 Press the VOL lt p button to adjust the picture condition as you want 5 Press the TV AV button to store for the picture User Position av Adjust 4 Back MENU Exit TW AV Selected Item Setting Change yo Contrast More darkness VOL 0 100 VOL More light PONR AX Brightness Less bright VOL 0 100 VOL More bright Colour Lower color intensity VOL 0 100 gt VOL Higher color intensity O Sharpness Soft picture VOL lt 0 100 VOL Sharp picture RU wn z Auto Picture Control The Picture options Dynamic Standard Mild and Game are programmed for good picture reproduction at the factory and cannot be changed PSM Picture Status Memory 1 Press the PSM button 2 Press the PSM button repeatedly to select PSM Each press of the button changes the screen display as below PC ARCI Dynamic Standard Mild gt Game User l e Dynamic Vivid Picture Appearance e Standard Standard Picture Appearance
7. the PC screen appears on the set The set can be operated as the PC monitor Resolution Horizontal Vertical Resolution frequency KHz frequency Hz 640 x 480 31 5 KHz 60 Hz VGA 640 x 480 37 9 KHz 72 Hz 640 x 480 37 5 KHz 75 Hz 720 x 400 31 4 KHz 70 Hz 800 x 600 35 1 KHz 56 Hz SVGA 800 x 600 37 9 KHz 60 Hz 800 x 600 48 1 KHz 72 Hz 800 x 600 46 9 KHz 75 Hz 1024 x 768 48 4 KHz 60 Hz XGA 1024 x 768 56 5 KHz 70 Hz 1024 x 768 60 0 KHz 75 Hz 720 x 480p 31 5 KHz 60 Hz 720 x 576p 31 2 KHz 50 Hz DTV 1280 x 720p 45 0 KHz 60 Hz 1280 x 720p 37 5 KHz 50 Hz 1920 x 1080i 33 7 KHz 60 Hz 1920 x 1080i 28 1 KHz 50 Hz Note a If the set is cold there may be a small flicker when the set is switched on This is normal there is nothing wrong with the set b Some dot defects may appear on the screen like Red Green or Blue spots However this will have no impact or effect on the monitor performance c Press the Q VIEW button to switch the 640x480 60Hz to 720x480P 60Hz Product Specifications Main body Thickness 180 mm Horizontal size 390 mm Weight 4 27 kg Height Power requirements DC 12V 3 0A Television system PAL BG I DK SECAM BG DK L AV NTSC Television programme VHF 2 12 UHF 21 69 Cable S1 S41 LCD Panel 15 TFT LCD panel Resolustion XGA 1024 X 768 Power consumption 45W External antenna imp
8. MAJESTIC International Head Office MAJESTIC GLOBAL Suite 1 20 Export Drive MOLENDINAR QUEENSLAND 4214 AUSTRALIA Ph 61 500 840 011 Fax 61 500 840 022 info majestic global com www majestic global com 500 0000051027 MAJESTIC 15 LCD TELEVISION USER MANUAL MV MY MY maje srFic oglob al c om Warnings RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel The lightning flash with arrowhead symbol within an equilateral A triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING To prevent fire or shock hazard do not expose the set to rain or moisture Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently CAUTION Do not attempt to modify this product in any way without written authorization Unauthorized modification could void the user s authority to operate this product Power This set op
9. VCR 3 Press the TV AV button to select Antenna D 00000 086 10 Input source 4 Press the PLAY button on the VCR _ VCR COMPONENT INPUT kJ 1 Connect the Video outputs Y Cb Cr on a DVD to the COMPONENT input on the TV aska GS 00000 2 Connect the audio cables from the DVD to the COMPONENT L MONO R inputs on the TV 3 Use the TV AV button to select COMPONENT mode 4 Press the PLAY button on the DVD COMPONENT DVD A V INPUT 1 Connect the A V out jacks on a VCR to A V IN jacks on the TV 2 Use the TV AV button to select VIDEO mode ma j i 3 Press the PLAY button on the VCR 228 The VCR playback picture appears on the TV screen Note If you have a mono VCR connect the audio cable from the VCR to the L MONO socket of the set VCR Headphone jack Insert the headphone plug to the headphone jack on the TV You can listen to the sound through the headphone and the speaker on the TV To adjust the headphone volume press the VOL lt p button If you press the MUTE button the sound from the headphone is turned off Headphone COMPONENT ANN Connecting the PC as a monitor This function is possible only when the set is in PC mode Use the TV AV button on remote controller Picture adjustment You can adjust picture Contrast Brightness Temperatu
10. ake sure the outside antenna is not disconnected The picture is doubled or tripled e Make sure the antenna is facing the right direction e There may be reflected electric waves from mountains or buildings The picture is spotted e There may be interference from automobiles trains high voltage lines neon lights etc e There may be interference between the antenna cable and power cable Try positioning them further apart There are stripes on the screen or colors fade e Is the unit receiving interference from other devices Transmission antennas of radio broadcasting stations and transmission antennas of amateur radios and cellular phones may also cause interference e Use the unit as far apart as possible from devices that may cause possible interference Memo
11. ceived signal b In PC mode radio mode supports only Auto c In PC mode radio control function is on an equality with Radio function in the front See page 20 Connecting the PC as a monitor Position Adjustment H V Position This function is to adjust picture to left right and up down as you prefer H Position V Position 1 Press the MENU button 2 Select the H V Position menu Position ay Adjust 4 gt 3 Press the PR a v button to select the desired Back ES RAWA position item 4 Press the VOL lt 4b button to adjust horizontal position and vertical position 5 Press the TV AV button to exit menu Auto This function is for the automatic adjustment of the screen position clock and clock phase The displayed image will disappear for a few seconds while the Auto configuration is in process Note Some signal from some graphics boards may not function properly If the results are unsatisfactory adjust your monitor s position clock and clock phase manually Reset This function allows you to return to the good picture reproduction programmed at the factory and cannot be changed Connecting the PC as a monitor PC INPUT 1 Connect the PC IN cable D sub jack lt gt from the monitor output socket of the PC to the PC input socket of the set 2 Connect the PC Audio IN cable from the PC to the PC AUDIO IN of the set 3 Press the TV AV or PC button to select PC mode 4 Switch on the PC and
12. e Back If no signal is being received or the signal is very weak a blue screen automatically replaces the noisy picture background If you wish to continue viewing the poor picture you must select the Blue Back Off Pressing the VOL lt b button will alternate between On and Off Auto Sleep If you select Auto Sleep On the set will automatically switch BA wx itself to standby mode approximately ten minutes after a TV Channel stops broadcasting 1 Press the MENU button 2 Select the Special menu 3 Press the PR a v button to select Auto Sleep 4 Press the VOL lt p button to select On 5 Press the TV AV button to return to normal TV viewing Childlock Childlock menu is necessary in order to disable the buttons on the side panel of the set Especially it is useful to prevent unauthorized viewing 1 Press the PRa v button to select Childlock 2 Press the VOL lt p button repeatedly to select On or Off When the setting is Childlock On the buttons on the front panel of the set is disabled When the setting is Childlock Off the buttons on the front HOLD INDEX panel of the set is enabled REVEAL MIX Radio You can listen to radio with the set 1 Press the MENU button 2 Press the PRA v button to select the Special menu Then press the VOL lt b gt button 3 Press the PRA v button to select Radio 4 Press the VOL lt p gt button to select Radio On or Off Note When the setting is On you can adjust
13. edance 750 Audio output 1 0W 1 0W External input ports e ANTENNA IN e DC 12V IN e PC IN e SCART e HEADPHONE JACK AVIN e PC AUDIO IN AC Power Adaptor AC 100 240 50 60Hz Output 12Vdc 3 0A Troubleshooting No picture on screen and no sound from speakers e Insert the AC power cord plug securely in AC power outlet e Make sure the remote control is not in the standby mode The POWER Standby indicator is red No picture No picture from AV terminal e Check the brightness setting of the display e Lamp may have malfunction e Make sure a cable with no VIDEO input signal is connected to the S VIDEO INPUT terminal Picture is displayed but no sound from the speakers e Check the sound setting e Make sure the sound is not muted e Make sure a pair of headphones is not connected e Make sure the connectors of the optional speaker system are securely inserted Picture is too light e Make sure COLOR and CONTRAST settings Picture is too dark Make sure BRIGHTNESS setting is not set too low e Lamp may have malfunction Remote control does not work The picture is not sharp The picture moves Change the batteries e Make sure the infrared transmitter window is not receiving strong light such as light from fluorescent lamps The reception may be weak e The state of the broadcast may also be bad e Make sure the antenna is facing the right direction e M
14. erates on a DC supply provided by the AC DC adaptor the voltage is as indicated on the label on the back cover Use only the AC DC adaptor supplied with the set and never apply an AC mains to the set directly The AC DC adaptor operates on an AC mains supply the voltage is as indicated on the label of the AC DC adaptor a Connect the DC plug of the AC DC adaptor to the 12V socket of the set b Connect the AC DC adaptor and its power cord c Connect the power cord to an AC mains In the event of thunderstorms or power cuts please pull out the mains plug of the AC DC adaptor and the aerial plug Do not allow anything to rest upon or roll over the power cord and do not place the set where the power cord is subject to damage Warnings Service Never remove the back cover of the TV this can expose you to high voltage and other hazards If the TV does not operate properly unplug it and call your dealer Connect the antenna cable to the connection marked Ant on the rear For best reception use an outdoor antenna Location Position your TV so that no bright light or sunlight will shine directly on the screen Do not expose the TV to vibration moisture dust or heat Also ensure that the TV is placed in a position that allows a free flow of air Do not cover the ventilation openings on the back cover You can install the TV on a wall or place it on a table top or similar flat surface Mounted the TV securely to eliminate the risk of injur
15. lance menu with the VOL lt p gt button MAJESTIC and adjust the balance of speaker 9 Select the AVL Automatic Volume Leveler menu ON or OFF 10 Select the Surround menu On or Off 11 Select the Sound Mode menu If the sound quality is poor while you are watching a programme broadcast in Stereo select MONO with the VOL lt p button Press the VOL gt button to switch between MONO and STEREO Please note that it works only when the broadcast is done in stereo If a programme is received in two language dual language you can switch to DUAL or DUAL II by pressing the VOL lt button repeatedly DUAL sends the primary broadcast language to the loudspeakers DUAL JI sends the secondary broadcast language to the loudspeakers Sound Control Auto Sound Control The sound Flat Music Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed SSM Sound Status Memory 1 Press the SSM button 2 Press the SSM button repeatedly to select Each press of the button changes the screen display as below Flat Music Movie gt Speech User PC I ARC TEXT SIZE HOLD INDEX UPDATE TIME REVEAL MIX QQ eQ Q Other functions You can control other functions Clock Blue Back Auto f Special Sleep Childlock Radio menu p Clock gt Blue Back Off Auto Sleep Off Clock Childlock Off Setting the clock is necessary in order t
16. n to adjust the sound level Quick view Press the Q VIEW button to view the last channel you were watching Sound mute function Press the MUTE my button The sound is switched off and the mute display mx appears To cancel mute mode press the MUTE x button again VOL lt gt or SSM button On screen menu language selection PC ARC SIZE HOLD INDEX REVEAL MIX TIME MAJESTIC Neeser Tang The menu can be displayed on the screen in desired Language language First select your language English 1 Press the MENU button Deutsch 2 Select the Setup menu e 3 Select the Language menu Italiano 4 Press the PRa v button to select your desired Potuga 3 language a Posto lt 5 Press the TV AV button Back MENU Exit TV AV All the on screen displays will appear in the selected language On Screen Menus and Displays gt Equalizer 1 Press the MENU button to display Main Menu gd 2 Press the PR av button to select menus Picture ae Sound Special Setup Movie ZESBE 3 Adjust each menu with the VOL lt b button Speech 4 Press the MENU button to return to preceding SEE WDRO gt OK menu a z P 7 Position aw 5 Press the TV AV button to finish adjusting menu Back MENU Exit TWAV i C
17. o use the various Radio Off timer features of the TV You can set automatic TV On or Output Frequency 87 9MHz Off time Position av Next lt gt Back MENU Exit TV AV J 1 Press the MENU button 2 Press the PRA v button to select the Special menu Then press the VOL lt gt button 3 Press the VOL lt p button to select Clock menu Clock Glock Off Time Off On Time Off On Programme 1 Position av Adjust lt gt L Back MENU Exit TV AV 4 Set the present time with the numeric buttons and the PRa v button on remote controller Store a time value between 00 00 23 59 hours minutes 5 Press the PRA v button to select Off Time 6 Set the TV off time with the numeric buttons and the PRa v button Then press the VOL lt p button Select On or Off with PR A v button When the setting is off the TV set will be switched off to stand by mode 7 Press the PRa v button to select On Time 8 Set the TV on time with the numeric buttons and the PRa v button Then press the VOL lt p button Select On or Off with PRa v button When the setting is On the set will be switched On automatically to the last selected programme 9 Press the PRA v button to select On Programme You can select the first displayed programme with the VOL lt p button when the set is switched on automatically 10 Press the TV AV button to return to normal TV viewing Other functions Blu
18. on or directly number buttons to select a Channel 7 Press the PRA v button to select the Table menu 8 Press the VOL lt gt button to select V UHF or Cable as required 9 Select a TV system with the VOL lt gt button BG Germany Asia M East Africa Australia I UK Hong Kong South Africa DK CIS China East Europe M USA KOREA Philippines 10 Press the PRa v button to select Search menu When you press the VOL lt b buttons the TV changes programmes in sequence You will see all the programmes that the TV has memorized You will not see programmes that were either erased or not memorized 11 Press the PRa v button to select Memorize menu 12 Press the VOL lt b button to store it 13 Press the MENU button to return to prior menu 14 Press the TV AV button to return to normal TV viewing oo Setting up TV Programme j Preqaeee_ _ _ Programme Edit Programme Edit This function enables you to delete or skip the stored P00 programmes Also you can move some programmes to other P03 programme numbers or insert a blank programme data into P04 the selected programme number m Delete 1 Press the MENU button ENO 2 Select the Setup menu Position av 4 k Back MENU Exit TV AV 3 Press the PR v button select Programme Edit menu 4 Select the programme name to edit with the PR A w and VOL lt p button Deleting a programme 1 Select a programme to be deleted with
19. oup and the blue field indicates the next block Group block page selection 1 With the BLUE button you can progress from block to block 2 Use the YELLOW button to proceed to the next group with automatic overflow to the next block 3 With the GREEN button you can proceed to the next existing page with automatic overflow to the next group Alternatively the PRa button can be used 4 The RED button permits to return to previous selection Alternatively the PRw button can be used FLOF text The Teletext pages are colour coded along the bottom of the screen and are selected by pressing the corresponding coloured button Page selection 1 Press the INDEX button to select the index page 2 You can select the pages which are colour coded along the bottom line with the same coloured buttons 3 The PRa v button can be used to select the preceding or following page PCi ARC HOLD INDEX REVEAL MIX TELETEXT Special TELETEXT functions Changes Teletext mode TEXT Selects double height text Press this button to enlarge the top half of the page Press this button again to enlarge the bottom half of the page Press this button again to return to the normal display z SIZE Stops the automatic page change which will occur if a Teletext page consists of 2 or more sub pages The number of sub pages and the sub page displayed is usually shown on the screen below the time When this bu
20. r Before you use the remote controller please install the batteries 1 POWER Turns the TV on from standby or off to standby mode 2 MUTE Turns the sound on and off 3 NUMBER buttons Selects programme numbers 4 TV AV Selects TV COMPONENT VIDEO RADIO Only when the set is Radio On or PC mode Clears the menu from the screen 5 MENU Displays a main menu 6 LIST Displays the programme list menu 7 MII Selects the language during dual language broadcast Selects the sound output 8 SLEEP Sets the sleep timer 9 Q VIEW Returns to the previously viewed programme 10 PRa v Programme Up Down Selects next programme or a menu item 11 OK Accepts your selection or displays the current mode HOLD REVEAL Controls 12 VOL lt p gt Volume Up Down Adjusts the sound level Adjusts menu settings 13 PC Selects the PC mode 14 PSM Picture Status Memory Recalls your preferred picture setting 15 SSM Sound Status Memory Recalls your preferred sound setting 16 TELETEXT button These buttons are used for Teletext For further details see the Teletext section Battery installation A z TEXT SIZE HOLD INDEX Minserting batteries 1 Remove the battery cover by pulling it upward UPDATE TIME REVEAL MX in the direction shown by the arrow 2 Insert the batteries with correct polarity to and
21. radio function in radio mode see page 20 Output Frequency This function can hear sound of TV with external device when frequency of TV and external device does correspond 1 Press the MENU button 2 Press the PRA v button to select the Special menu Then press the VOL lt b button 3 Press the PRA v button to select Output Frequency 4 Press the VOL lt b button to select desire frequency PC ARC Radio Control This function is possible only when the set is in Radio mode Radio mode is displayed when the Setting for special menu is radio On 1 Use TV AV button on remote controller to select Radio mode 2 Press the MENU button to set Radio Setup menu 3 Press the VOL lt p gt button repeatedly to select Mode Auto or Manual 4 Press the PRa v button select Frequency Then press the VOL lt 4b button repeatedly to tune in the desired station manually 5 Press the PRa v button to select Programme Then press the VOL lt 4b button repeatedly to select programme 6 Press the PRa v button to select Delete Select Off with the VOL lt b button to delete the station 7 Press the PR v button to select memorize If you want to memorize this radio setup press the VOL lt gt button 8 Press the PR v button to Radio Auto Programme select Auto Programme 9 Press the VOL lt gt button Start repeatedly to automatically scans and tunes to the next SR available station Back MENM BX 10
22. re Clock Phase as you prefer 1 Press the TV AV button to select the PC mode Press the MENU button Select the Picture Press the PRa v button to select the desired picture item Press the VOL lt p gt button to make appropriate adjustments Press the TV AV button to exit menu 2 3 4 5 6 Contrast This function is to adjust picture to light dark Brightness This function is to adjust brightness of picture Temperature Temperature is a measure of the warmth of the image color Clock This function is to minimize any vertical bars or stripes visible on the screen background And the horizontal screen size will also change Note This mediation range is different according to the supported resolution Phase This function allows you to remove any horizontal noise and clear or sharpen the image of characters I Picture Brightness 80 Temperature 9300K Clock 50 Phase 34 Position av Adjust lt gt L Back MENU Exit TV AV Main Menu Picture gt Sound gt H V Position gt Auto Reset 1024 x 768 60Hz Position av Next lt gt Exit TV AV Contrast 60 POWER O Connecting the PC as a monitor Sound adjustment eS Press the MENU button j gt Select the Sound menu BEDE 5 3 Press the PRA v button to select the desired AVL Off sound item Equalizer Balance AVL Surround or Surround Off Sound Mode Sound Mode L R 4 Pre
23. ss the VOL lt gt button to make desired adjustment PL Fe 5 Press the VOL lt p button in Equalizer to set the Potion av Next Equalizer Back MENU Exit TWAV 6 Press the PR v button to select your preferred setting Flat Music Movie Speech or User To set the Equalizer User oo WNE a Select User by pressing the PR a v button Equalizer b Select a sound band by pressing the VOL lt gt Flat button Music c Make appropriate sound level with the PRA v Movie JSS button Speech d Press the MENU button to return to preceding User 0 1 0 5 15 5 0 10KHz menu 7 Press the PR v button to the Balance menu da AV 8 Select the Balance menu with the VOL lt b button and adjust the balance of speaker 9 Select the AVL Automatic Volume Leveler menu ON or OFF 10 Select the Surround menu ON or OFF 11 Select the Sound Mode with PRa v button 12 Press the VOL lt p button to select sound mode L R L L R R L R Audio signal from audio L input is sent to left loudspeaker and audio signal from audio R input is sent to right loudspeaker L L Audio signal from audio L input is sent to left and right loudspeakers R R Audio signal from audio R input is sent to left and right loudspeakers 13 Select the Input with PRa v button 14 Press the VOL lt p button to select Input PC Radio Note a When selecting radio mode sound mode alternates between MONO and STEREO according to the re
24. the PRA v or VOL lt 4b button 2 Press the RED button once The selected programme is deleted all the following programme is shifted up one position Naming a programme 1 Select a programme to be named with the PRA v or VOL lt p gt button 2 Press the GREEN button Then it display as below Adjust av 4 Confirm OK 3 Press the PR v button Back MENU Exit TV AV repeatedly to edit programme name You can use the numeric 0 to 9 the alphabet A to z capital and small letters a blank and With the VOL lt p button you can select in the opposite direction 4 Press the OK button to store it 5 Press the MENU button to return to prior menu 6 Press the TV AV button to return to normal TV viewing Moving a programme 1 Select a programme to be moved with the PRA v or VOL lt p gt button 2 Press the YELLOW button 3 Move the programme to desired programme number with the PRA v or VOL lt b button 4 Press the YELLOW button again to release this function Skipping a programme number 1 Select a programme number to be skipped with the PRA v or VOL lt p button 2 Press the CYAN button The skipped programme turns to blue 3 Press the CYAN button again to release the skipped programme Edit Name Station Note When a programme number is skipped it means that you will be unable to select it using the PR v button during normal TV viewing If you want to select the skipped programme
25. tton is pressed the stop symbol is displayed at the top left hand corner of the screen and the automatic page change is inhibited To continue press this button again HOLD Return to index page INDEX Displays the TV picture on the screen while waiting for the new Teletext page The display will appear at the top left hand corner of the screen When the updated page is available then display will change to the page number Press this button to view the updated Teletext page X UPDATE When viewing a TV programme press this button to display the time at the top right hand corner of the screen Press this button again to remove the display In Teletext mode press this button to select and hold or change a four digit sub page number This is displayed along the bottom of the screen Press this button again to exit this function TIME Press this button to display the concealed information such as solutions of riddles or puzzles Press this button again to remove the information from the display REVEAL MIX Only Teletext mode text mode superimposed on the q TV picture TV mode External Equipment Connection You can connect additional equipment such as VCRs camcorders etc to your set Examples are shown below Antenna connection 1 Connect RF out on the VCR to the Antenna input on the rear of the TV 2 Connect the antenna cable to the antenna in jackon the
26. u programmed Programmes can be tuned using automatic or manual modes Auto Programme All programmes that can be received are stored by this method It is recommended that you use Auto programme during installation of this set 1 Press the MENU button 2 Select the Setup menu 3 Select the Auto Programme menu 4 Press the PRA v button to select System 5 Select a TV system with the VOL lt p button BG Germany Asia M East Africa Australia I UK Hong Kong South Africa DK CIS China East Europe M USA KOREA Philippines Select the Start menu to start Auto Programme Press the MENU button to stop Auto programme Press the TV AV button to return to normal TV viewing 0 No Auto Programme System BG Start Position av Adjust lt gt L Back MENU Exit TV AV POWER dX O Setting up TV Programme Manual Programme Manual ene Manual Programme lets you manually tune and arrange the programmes in whatever order you desire Also you Gyaramme can assign a programme name with 5 characters to each Table V UHF programme number SB R 1 Press the MENU button Memorize 2 Select the Setup menu Namo sss oo J 3 Select Manual Programme menu Position ay Adjust lt gt 4 Select a programme with the VOL lt p button or Back MENU Exit TWAV number buttons Press the PR v button to select Channel menu Press the VOL lt p butt
27. y from the TV falling Cleaning Unplug the TV before cleaning the face of the LCD Screen Dust the TV by wiping the screen and cabinet with a soft clean cloth If the screen requires additional cleaning use a clean damp cloth Do not use liquid or aerosol cleaners Contents Before operating the set please read this manual carefully Supplied Accessories Controls Controller of panel Remote controller Basic Operation e Turning the TV On and Off Programme selection Volume adjustment Q View Sound mute Junction EELEE ENESE ENTIE TEETE OOE izotop do edo EAEI On screen Language selection On Screen Menus and Displays Setting up TV Programme ecce creec eee ttt ities Auto Programme Manual Programme Programme Edit Picture Control h1h1 1414 rienda aN iA AeA AATA ia AERD Manual picture Control cities Auto picture control Sound Control 0 0 0 aaa Other funection saw o AAA A A EA Clock Childlock Radio Control Teletext TOP text FLOF text Special Teletext function cc ieee eee teenie terest erisireenrieeieeerices External Equipment Connection Antenna connection Headphone jack Connecting the PC asa monitor Product specification Troubleshooting 21 22 21 21 21 22 23 24 23 23 23 23 24 27 28 29 Supplied Accessories E Make Sure the following accessories are provided with Product
Download Pdf Manuals
Related Search