Engine Gateway Monitor
Contents
1. The completely sealed Veethree EGM with 320 H x 240 V QVGA resolution is fully sunlight viewable and electrically and environmentally rugged it provides tough flexible and maintenance free instrumentation in all types of environmental conditions The EGM unit is waterproof and has built in day and night modes for comfortable monitoring in all types of visibility and weather conditions Veethree EGM supports three engine types NMEA 2000 J1939 e Non electronic Each EGM display can be allocated to the port or single starboard and or the centre engines and when connected displays multiple functional data parameters of an engine The Veethree EGM interface offers four switchable gauge display screens and one fuel management screen to enable easy and real time monitoring of engine performance 1 1 Input or Output Compatibility 1 1 1 J1939 J1939 is the engine data protocol that runs over the industrial CANbus that is used to exchange data between two engines It is used to synchronize RPMs on a twin engine vessel or to drive physical gauges 1 1 2 NMEA 2000 National Marine Electronics Association NMEA 2000 is the standard for serial data networking of marine electronic devices It is the plug and play communication standard that is used to connect marine sensors and display units within ships and boats Communication takes place at the speed of 250 kilobits per second allowing any sensor to communicate with any display2. Engine Gateway Monitor 3 NMEA 2000 ossee 4 Engine ID 23 NMEA 2000 Settings 29 F Fluid Level Instance and Gateway 29 Page 54 Veethree EGM Installation and User Manual Instruments S Secondary Connector cceeeeeeeee 9 P Selecting View Modes cs0c0 45 Power Connection and SPCC o TTT 27 System Configuration ernvrrnnnrrns 22 Precautions ssessssseseessrresssererrsssees Primary Connector Product Specification U UART Viewer r rnnonnnnnennnnnnrannnennne 37 R Go a T ets 20 Restore Defaults rrnnrrrnrrrnvornnrr 40 ETE 18 RPM Calibration cscccssesseeeees 32 Rudder Angle csccsssccesessreeeees 28 V Veethree EGM User Interface 16 Page 55 Veethree Instruments EGM Installation and User Manual Page 56 Veethree Instruments EGM Installation and User Manual Page 57 Veethree Electronics and Marine LLC 2050 47th Terrace East Bradenton Florida 34203 USA Tel Office 941 538 7775 Fax 941 755 1222 www V3instruments com
3. Page 23 Veethree Instruments EGM Installation and User Manual Data Sources The Data Sources menu enables configuration of the input source from where the display receives data EGM can receive input data from any of the following N2K NMEA 2000 J1939 I O senders N183 NMEA 0183 Demo C All the Data Sources submenu can be configured to Demo and N2K NMEA 2000 options DEMO option will override the actual reading being sent to EGM display The Data Sources menu contains the following submenus Engine Battery Fuel Speed Rudder Angle To configure Data Sources 1 Press Key 1 or Key 2 to scroll to the Data Sources submenu in the System Configuration menu Press Key 4 to select Data Sources The Data Sources menu appears Page 24 EGM Installation and User Manual Veethree Instruments BEITE fs Ted Battery Fuel Speed Rudder Angle Figure 18 Data Sources Menu A Engine Configure the following engine parameters in the Engine menu RPM e Oil temperature e Oil pressure e Boost pressure e Coolant temperature e Coolant pressure e Load percentage e Torque percentage e Tilt Trim Engine Hours e Fuel rate e Fuel pressure To configure engine input sources 1 Press Key 1 or Key 2 to scroll to the Engine submenu in the Data Sources menu 2 Press Key 4 to select Engine The Engine menu appears 3 Press Key 1 or Key 2 to
4. SOG Speed over water Display other engine fuel and functional parameters Display engine speed hours and depth Display number of the EGM display page Scroll select and make various configuration and user s custom settings Page 16 EGM Installation and User Manual Veethree Instruments 3 7 Configuration of System Settings A System Configuration must be carried out ONLY by the Installation Engineer or an authorized system administrator Commission the EGM display by configuring the various EGM display settings When the display is powered down it will save and store the configured settings ready for quick and easy access when it is turned on again the next time To access the system setup main menu and configure settings press and hold Key5 for approximately five seconds The Main Menu appears The functionality of the respective soft keys is described below Main Menu Alarm Setup System Configuration About Key 1 To move up to choose a menu option or a submenu Key 2 To move down to choose a menu option or a submenu Key 3 Key 4 To select a menu option ora submenu and to configure display parameters NEVE To return to the previous menu Page 17 Veethree Instruments EGM Installation and User Manual 3 7 1 Main Menu The configuration options available in the Main Menu are User Setup Alarm Setup System Confi
5. Temperature Volume and so on Press Key 4 to select the preferred unit for the selected engine parameter Press Key 5 to save and return to the User Setup menu Volume Distance Flow Rate Speed Depth Figure 13 Measuring Units Settings Page 20 Veethree Instruments EGM Installation and User Manual D E Max RPM and Max Speed To set the maximum engine RPM and speed display settings 1 Press Key 1 or Key 2 to scroll to the Max RPM or Max Speed submenu highlighted in yellow in the User Setup menu 2 Press Key 4 to set the maximum reading value User Setup User Setup _ Language Language Key Tone Key Tone Units Units Max RPM WERE AA Jt Figure 14 Max RPM and Max Speed Settings 3 7 1 2 Alarm Setup Alarms can be enabled and disabled for Analogue J1939 DM1 and NMEA 2000 inputs To enable and disable alarm 1 Press Key 1 or Key 2 to scroll to the Alarm Setup menu highlighted in yellow in the Main Menu 2 Press Key 4 to select Alarm Setup The Alarm Setup screen appears 3 Press Key 1 or Key 2 to scroll to the Analogue or J1939 DM1 or NMEA 2000 options 4 Press Key 4 to toggle and select Enabled or Disabled Press Key 5 to save and return to the Main Menu Page 21 Veethree Instruments EGM Installation and User Manual Alarm Setup Analogue Disabled J1939 DM1 Enabled Figure 15 Alarm Setup 3 7 1 3 System Configuration The System Con
6. the display harness e Connect the spare Black wire from the display used for all analogue senders to the ground 3 5 5 Connecting to Fuel Level Sender Measure the fuel level from the two wire fuel level sender by making the following connections e Connect the fuel level signal from the sender to the Blue wire of the display harness e Connect the spare Black wire from the display used for all analogue senders to the ground 3 5 6 Connecting to a Trim and Tilt Sender Measure the tilt trim one per display from a standard two wire tilt trim senders by making the following connections e Connect the trim tilt sender to the Orange wire of the display harness e Connect the spare Black wire from the display used for all analogue senders to the ground 3 5 7 Connecting to GPS NMEA 0183 Signal The NMEA 0183 GPS is connected to the EGM display to display Speed Over Ground SOG and Course Over Ground COG Connect the NMEA 0183 to the Green wire of the display harness Page 15 Veethree Instruments EGM Installation and User Manual 3 6 Veethree EGM User Interface Left Gauge Pace SELECT KEY1 KEY2 KEY3 B KEY4 KEY5 Figure 9 EGM User Interface Veethree EGM provides a robust and user friendly interface and controls to enable the users to configure customize and monitor engine data Top Gauge Left and Right Gauges Data Box Page Num Soft Keys 1 to 5 Display engine speed
7. to the previous options Press Key 4 to select STATS The statistics screen appears CAN PORT 1 STATISTICS x Frames 0 x Errors 0 ollisions 0 Figure 34 CAN Viewer Statistics Screen B UART Viewer UART Viewer displays the raw NMEA 0183 data that is being received To view NMEA 0183 data in the UART Viewer 1 Press Key 1 or Key 2 to scroll to the UART Viewer submenu highlighted in yellow in the Diagnostics menu Press Key 4 to select UART Viewer The UART Viewer screen appears Page 37 Veethree Instruments EGM Installation and User Manual 3 Press Key 5 to save and return to the Diagnostics Menu UART PORT Rdindex 0 Wrindex 0 Figure 35 UART Viewer C 10 Debug Screen The IO Debug screen displays analog inputs outputs and digital outputs You can also check the display for any bugs To view analog inputs outputs and digital outputs 1 Press Key 1 or Key 2 to scroll to the IO Debug Screen submenu highlighted in yellow in the Diagnostics menu 2 Press Key 4 to select IO Debug Screen The IO Debug Screen appears Press Key 1 to view Analogue Inputs 4 Press Key 2 or Key 3 to view the outputs Press Key 5 to save and return to the Diagnostics Menu Analogue Inputs Description Mode Input Calc Destination Output Analogue 1 R 0 000 Oil Pres 0 000 Analogue 2 R 0 000 Coolant Temp 0 000 Analogue 3 R 0 000 Boost Pres 0 000 Analogue 4 R 0 000 Tilt Trim 0 000 Analog
8. will be restored to their default settings To restore company default settings 1 Press Key 1 or Key 2 to scroll to the Restore Defaults submenu highlighted in yellow in the System Configuration menu 2 Press Key 4 to select Restore Defaults The Restore Defaults screen appears Restore Defaults Figure 39 Restore Defaults Page 40 Veethree Instruments EGM Installation and User Manual Chapter 2 User Operation Page 41 Veethree Instruments EGM Installation and User Manual This page is intentionally left blank Page 42 EGM Installation and User Manual Veethree Instruments 4 User Interface Left Gauge Top Gauge Right Gauge PAGE SELECT KEY2 KEY3 KEY4 KEYS Figure 40 User Interface To select and view a display page To select a gauge The selection of gauge is indicated by a red rectangular box To choose a parameter that will be displayed in the selected gauge on the page To display alarm screen This is applicable only when an alarm is active To open the display settings menu brightness and view modes To access the Main Menu hold down Key 5 for approximately five seconds Page 43 Veethree Instruments EGM Installation and User Manual 5 Interface View Settings Veethree EGM provides the option to adjust user interface brightness and view modes to suit day and night operational requirem
9. CAN High and CAN Low CAN termination resistance must be between 90 ohm and 150 ohm If the measured resistance is not within the range add a 120 Ohm resistor between the CAN High and the CAN Low 3 5 3 Connecting to Non electronic Engine When connecting the display to a non electronic engine signals from the senders are directly connected to the display harness Connect the display to non electronic engine by making the following connections e Connect the oil pressure signal from the sender to the Black with White band wire e Connect the coolant temperature signal from the sender to the Brown with White band wire e Connect the boost pressure signal from the sender to the Red with White band wire e Connect the oil temperature signal from the sender to the Pink wire e Connect the tachometer signal from W or R or AC to the Violet wire C A tachometer signal can be drawn from the W terminal of the alternator If W terminal is unavailable the signal can be drawn from R or AC terminal of the alternator If W R and AC terminals are unavailable an alternator shop can install a tap for the tachometer signal Page 14 Veethree Instruments EGM Installation and User Manual 3 5 4 Connecting to Rudder Angle Sender Measure the rudder angle from the rudder angle sender by making the following connections e Connect the rudder angle signal from the sender to the Yellow with White band wire of
10. E 4 3 33 OPEN BEZEL _ 2 82 VIEWING DISPLAY 2 12 VIEWING DISPLAY 3 33 BEZE 3 75 OUTLINE Figure 2 EGM Front View Side View Page 6 Veethree Instruments EGM Installation and User Manual Figure 3 EGM Side View Rear View WATER PROOF USB CONNECTOR RECOVERY SWITCH MOMENTRY PUSH SECONDARY CONNECTOR MATES WITH DT04 12PB PRIMARY CONNECTOR MATES WITH DT04 I2PA Figure 4 EGM Rear View Page 7 Veethree Instruments EGM Installation and User Manual Primary Connector Signal Description 1 Black GND GROUND 2 Red PWR POWER 10 V DC 30V DC Must be protected by 500 MA circuit breaker fuse 6 3 Brown RLA1 RELAY SOLENOID 5 OUTPUT 1 4 External Alarm 3 2 4 Blue White RLA2 RELAY SOLENOID 4 OUTPUT 2 Optional gauge light switch Figure 5 5 Black CAN2 ISOLATED CAN SUPPLY Connector PIN OUT 6 Red CAN2 ISOLATED CAN SUPPLY 7 White CAN2H ISOLATED CAN DATA H 8 Blue CAN2L ISOLATED CAN DATA L 11 Green CAN1L PRIMARY CAN DATA L 12 Yellow CAN1H PRIMARY CAN DATA H C Pin 5 Pin 6 Pin 7 and Pin 8 together form a DeviceNet CAN cable The DeviceNet CAN cable is used to receive or transmit the NMEA2000 data Pin 11 Green wire and Pin 12 Yellow wire is a twisted pair used for the J1939 i
11. Installation and User Manual 03 16 4 763 mm A INO JONIHISIH HOS LNAWNYLSNI 40 ANITLNO Not to Scale Figure 8 Mounting Template for Through the Dash Installation A DO NOT use the template illustrated in Figure 7 and Figure 8 for installation of your EGM Use the mounting template provided with the EGM display kit 3 3 Mounting EGM To mount the EGM display 1 Choose and attach the appropriate mounting template to the chosen location using adhesive tape 2 Mark drilling holes in the dashboard using the mounting template as a guide 3 Drill holes using a 3 16 or 4 763 mm drill bit Page 12 Veethree Instruments EGM Installation and User Manual C Before proceeding to the next step of fixing studding ensure that the rubber seal on the rear of EGM display is securely in place over the USB port access 4 Fixthe studding provided in the fitting kit into the four positions at the rear of EGM display 5 Feed the studding through the four holes drilled on the dashboard 6 Fix and hand tighten the nuts to the studding to secure the display in its position 7 Integrated rubber gasket will seal the display to the dashboard 3 4 Power Connection e Power the EGM display by connecting it to the engine battery If the EGM display cuts out due to engine cranking then connect the display to domestic battery e Use Black with Red band wire of the harness for the power c
12. Veethree Instruments Engine Gateway Monitor Engine Gateway Monitor EGM 9 PAGE SELECT Installation and User Manual Version 1 2 Copyright Copyright 2014 Declarations and Conformance This equipment is intended for use in international waters as well as coastal sea areas administered by countries of the E U and E E A In case of any queries contact our customer service center at techservice veethree com or 941 538 7775 ext 815 Preface About this document This document provides the information required to install configure and use the Engine Gateway Monitor EGM The EGM manual is structured into two chapters a glossary of terms and definitions and an index of key words Chapter 1 provides contextual description of the EGM installation and configuration procedure Chapter 2 provides monitor description and steps to use EGM interfaces to monitor various engine and fuel parameters and manage alarms Document Conventions Convention Description Bold User Interface terms appear in boldface font Note Note appears with the symbol O and borders above and below the text Warning Warning appears with the symbol Piana borders above and below the text Revision History Revision Number Date 1 0 March 2014 1 1 March 2014 1 2 November 2014 Veethree EGM Installation and User Manual Instruments Contents Chapter 1 EGM Installation and Conf
13. act highly flexible and rugged CANbus displays Features of Veethree EGM Compatible with N2K NMEA 2000 J1939 and non electronic engine types with or without an Engine Control Unit ECU Acts as an Analogue to NMEA2000 and J1939 to NMEA2000 digital gateway to allow engine data to be retransmitted to other NMEA2000 devices Graphical display of primary engine parameters derived from traditional analogue engine senders NMEA 2000 or J1939 networks Primary display options include parameters related to engine status alarms fuel level rudder angle tilt and trim depth speed and heading Displays depth heading Speed Over Ground SOG and speed over water as available on NMEA2000 Displays SOG amp heading as available on NMEA0183 ISO and SAE standard icons and test based multi language menu Data is available in multiple formats and measurement units Output is included for driving an external alarm Page 3 Veethree Instruments EGM Installation and User Manual Veethree EGM is driven by CANvu software that provides selectable icon based display layouts CANvu software includes a comprehensive multi language text based fault warning and acknowledgement system and a series of hidden until lit alarms To allow multifunctionality and increased input or output capability Veethree EGM offers seven analogue inputs one digital input and four outputs one RS232 two CANbus 2 0B and a USB 2 0
14. cessor ROM RAM and an I O control unit NMEA National Marine Electronics Association NMEA 2000 is the standard for serial data networking of marine electronic devices Non electronic Non electronic engine is an engine that is not engine controlled by an ECU ECM It is also termed as Mechanical Engine or Non ECU Engine SOG Speed Over Ground is the speed of the vessel relative to the surface of the earth Page 53 Veethree Instruments EGM Installation and User Manual 10 Index A Fuel Management rrnnrrnnvernvrrvnvernr 34 Fuel Management Page 006 49 ADOU tesa citive aaa eens 52 Adjusting Interface Brightness 44 Alarm Setup ereenn 21 Analogue Settings sccsccsseeees 32 B J Batty rires eten 26 W193 e E 4 C J1939 Settings 31 CAN VIEWET sn ceccsicccvssesaconcetscenscorese K CANvu software Changing the Gauge Display Motes 48 Key TONG sininen 19 Choosing the Mounting Location 11 Configuration of System Settings 17 L Language iisimmin 18 D Data Input Connections 13 M Data SOUrces mmmmrsrnrvvvrersvvrenersvren Data Viewer rrersrnvrnrrrrensvsvensvsvreee Managing AlIBrms eussmsenessssesssiss a0 Diagnostics Menu Max RPM and Max Speed 21 DIMENSIONS c0 coisesacsacevscesassossestssensee Meme FEM vn Mounting Template E N EGM Display Gauges ssmrnnnrrnvrrnnnr 46 Engine 25 NMEA 0183 Settings 30
15. ectrical wires are dressed away from moving or hot engine components Protect the wires or cables running through the drilled holes using grommets and by deburring the holes Disconnect the battery before making any electrical connections Reconnect the battery only after you have checked and ensured proper electrical connections Ensure that the power supply to operate EGM is 10 V to 32 V DC Page 10 Veethree Instruments EGM Installation and User Manual 3 Installation and Configuration 3 1 Choosing the Mounting Location e Choose the installation type Flush mount dash installation or through the dash installation standard e Choose an appropriate location on the dashboard or a suitable place on the bridge to mount the EGM display unit e The chosen mounting location must allow the operator to easily control the display and clearly view the display screen e Ensure that there is a direct path to run all the connecting cables or harness 3 2 Mounting Template Veethree EGM mounting templates for Flush Mount Dash Installation and the Standard through the Dash Installation are provided along with the EGM display kit The mounting template is used to position mark and drill holes on the dashboard to fit the EGM unit CENTER LINE Not to Scale Figure 7 Mounting Template for Flush Mount Dash Installation Page 11 Veethree Instruments EGM
16. enersrreressenerserenersnne 25 Figure 19 Engine nausstndsnnmnsnrnn nisjene RAN 26 Figure 20 Battery eiiean ien A aE 26 Figure 21 Fuel Levelei 27 Figure 22 Speed accents nites ee 28 Figure 23 Rudder Angle c essscesscscetesscesenesseeeseeeesaceecseseeesseeeeseeaees 29 Figure 24 NMEA 2000 Settings rnrrrrrnnvnrenenrrrvrenernerenenrererenerrerserenensene 30 Figure 25 NMEA 0183 ursinii 30 Figure 26 J1939 Settings ececceeesceeeeeeeeeesseeeeeecseeeaeeeseeseeesetaeeeeeas 32 Figure 27 RPM Calibration enoerorononrvrernrrorerenrererererserennsrenerrerenessenenenne 33 Figure 28 Analogue Settings orrnnnnnvvnvnnrerenenrerenernrrerenersereererenessenenenne 34 Figure 29 Fuel Management se eeecceeseeseteeseeeeeeeeeesseeeesaeeeneeeeetenees 34 Figure 30 Diagnostics Menu ou cece sseeceeeseeceteesceeeseeseesaeeeesaeeeneeeeeeenees 35 Figure 31 CAN Viewer neneresverenrrrerenerrererernerenenesserenessnnessenenesserenesserenenne 36 Figure 32 CAN Viewer Log Screen usersunrvnrererenerrererersrrererserensene 36 Figure 33 CAN Viewer Recording Screen seess 37 Page iii Veethree Instruments EGM Installation and User Manual Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 CAN Viewer Statistics Screen um nvnrnrernrrrerrrerrrrerererren 37 UART V
17. ents A simple user friendly toolbar facilitates the functionality 5 1 Adjusting Interface Brightness To adjust user interface brightness of EGM 1 Press Key 5 to open the interface view settings menu The view settings tool bar appears 2 Press Key 1 to decrease and key 2 to increase the brightness of the EGM display screen Figure 41 User Interface View Settings Page 44 EGM Installation and User Manual Veethree Instruments 5 2 Selecting View Modes To select view modes 1 2 3 4 Press Key 5 to open the interface view settings menu The view settings tool bar appears Press Key 3 to set the EGM display screen to the day mode 9 PAGE SELECT Figure 42 Day Mode Press Key 4 to set the EGM display screen to the night mode TEU ETF N 100 Z E 50 KM H 150 A 0 3290 neu 2003 os AD Be 200 1 400 600 gt Se 1000 Figure 43 Night Mode Press Key 5 to save and return to the EGM main interface Page 45 Veethree Instruments EGM Installation and User Manual 6 EGM Display Gauges Veethree EGM has 4 gauge display pages and 1 fuel management page The top gauge includes the data box Top Gauge The Top Gauge in the page is to display Parameter Icon Engine Speed Speed over water Speed over ground The data box displays e Engine speed e Engine hours e Depth Bottom Left and Right Gauge The botto
18. figuration menu is used to configure input sources from where the display will receive information and how it will respond to the information that it receives C Before configuring the system setting switch on power to the system and check if all the display s power up correctly To access the System Configuration menu 1 Press Key 1 or Key 2 to scroll to the System Configuration submenu in the Main Menu highlighted in yellow 2 Press Key 4 to select System Configuration The System Configuration menu appears System Configuration Data Sources NMEA 2000 Settings J1939 Settings Analogue Settings Fuel Management Figure 16 System Configuration Menu Page 22 Veethree Instruments EGM Installation and User Manual The System Configuration menu contains the following submenus Engine ID Data Sources NMEA 2000 Settings J1939 Settings Analogue Settings Fuel Management Diagnostics Restore Defaults Engine ID The Engine ID indicates the engine to which the display is connected To configure Engine ID 1 Press Key 1 or Key 2 to scroll to the Engine ID submenu in the System Configuration menu Press Key 4 to select Engine ID Press Key 4 to set the Engine ID to Port or SGL Starboard or Centre System Configuration DF he Welell mer ts NMEA 2000 Settings NMEA 0183 Settings J1939 Settings Analoque Settings 1 i 1 Figure 17 Engine ID Selection
19. guration About 3 7 1 1 User Setup Configure the following preferences display range and limits in the User Setup screen Language Key Tone Units Max RPM Max Speed User Setup Key Tone Units Max RPM Max Speed Figure 10 User Setup A Language To set the preferred language 1 Press Key 1 or Key 2 to scroll to the Language submenu highlighted in yellow in the User Setup menu Press Key 4 to select Language The Language options list appears Page 18 EGM Installation and User Manual Veethree Instruments 3 Press Key 1 or Key 2 to scroll to the preferred language 4 Press Key 4 to select the preferred language 5 Press Key 5 to save and return to the User Setup menu Language Spanish Swedish French German Italian Figure 11 Language Setting B Key Tone To set the key tone 1 Use Key 1 or Key 2 to scroll to the Key Tone submenu highlighted in yellow in the User Setup menu 2 Press Key 4 to select On or Off User Setup Language Units Max RPM Max Speed Figure 12 Key Tone Setting Page 19 Veethree Instruments EGM Installation and User Manual Units To set the measuring units for the engine parameters 1 Press Key 1 or Key 2 to scroll to the Units submenu highlighted in yellow in the User Setup menu Press Key 4 to select Units The Units menu appears Press Key 1 or Key 2 to scroll to the various engine parameters
20. iewer nennennenveneenrenrrerenrernerreenesnernernesnneereenesnesnsenesnsenne 38 IO Debug Screen Analogue INputs s es 38 IO Debug Screen Outputs sesvrrerrnvrrerenerrerenerrerenernrrerenenn 39 Data VIGWOK es cect ectecias E E 39 Restore Detaul i3 cicciehidniauidiiuiaieniedisaahdieawets 40 User Inte race c iich seic ssties aa a aia 43 User Interface View Settings rrnrvnrnnreronrnverenennrrenennrrenene 44 Day M d u unne innst aa 45 Night Mode cities cndcteved aneeshatti 45 Changing the Gauge Display 48 Fuel Management Page rnrrnrvnnnennnernnrvnnrvnnevnnsvnnnerenssnnenernn 49 EGM Performance Alarm and Warning cseeeeeee 50 Viewing and Suppressing an Alarm sses 51 About EE 52 Product Det ls nanunssndetasdedenegukeshatenuk en 52 Page iv Veethree Instruments EGM Installation and User Manual Chapter 1 EGM Installation and Configuration Page 1 Veethree Instruments EGM Installation and User Manual This page is intentionally left blank Page 2 EGM Installation and User Manual Veethree Instruments 1 Introduction The Veethree Engine Gateway Monitor EGM is a 3 5 display with integrated input and output features PAGE SELECT Figure 1 Veethree EGM Console The Veethree EGM monitors information available over a NMEA 2000 J1939 or information sent from an analogue engine EGM is a part of the new generation product suite of comp
21. iguration 0 1 MAYER AUC UNO me 3 1 1 Input or Output Compatibility 2 0 eee ccneeeeeeeeeeeeeeeeteeeseeeeteeeseeereaes 4 WA 1989 TE EE Aces 4 1 1 2 NMBA 2000 seen Hee nine aden Reis 4 1 2 Product Specificato Nessin 5 1 3 DIMENSIONS iaso tien iets a es 6 2 Getting UATEN 2anr pengane 10 2 1 Mithe BOX EN EE 10 2 2 PreCaUtiONS users 10 3 Installation and Configuration rrnnnnnnnnnnnnnvvnnnnnnnnnnnnnn 11 3 1 Choosing the Mounting Location asrvnonvnnonvnnenvnnenvnnnnrenenrnnenrnrenrnnnnrenen 11 3 2 Mounting Template ccceeceeeesecceeeseeceeeeseeeeseseneeeeneneeeeeseeeeneneeeeeseees 11 3 3 Mounting EGM icciccs cnccie si scdke hese nal eee aed caged sence bek 12 3 4 Power Connection rorrvnanvonrnvnnenvonenvnnnnvonenrnnenvnnenrnnenrensnrnnenvensnrnsenrene 13 3 5 Data Input Connections aerorvvnonvvnonvrnnnvnnenvnnenvnnenvnnenrnnsnrnnenrnsenrnsenrenen 13 3 5 1 Connecting to NMEA 2000 Optional asrrrrronrrrnonnrnnrnnrrnnrnnnrennnnrnnrnnnnnnnn 13 3 5 2 Connecting to J1939 Engines CANDUS rsnrrrnvrrnnvnnnvnnenrnnnnrnrnrnnrvrnrnverener 14 3 5 3 Connecting to Non electronic Engine rrrrnrrnnvrrnnvnnnvenenvnrnnrnrnvenrvrnrnvenenen 14 3 5 4 Connecting to Rudder Angle Sender anrnnnnrnnnvrnnnvnnnvnnnnvnrnnrnrnvnnrvrrrnvenener 15 3 5 5 Connecting to Fuel Level Sender ranrnnnvnnnnrnnnvrnnnvnnnvennnvnnnnrnrnvnnrnennnverenen 15 3 5 6 Connecting to a Trim and Tilt Sender ar
22. m left and bottom right gauge in the page are to display Parameter Icon Oil Temperature Oil Pressure Boost Pressure Page 46 Veethree EGM Installation and User Manual Instruments Parameter Icon Coolant Temperature Coolant Pressure Torque Percentage Tilt amp Trim Alternator Potential Fuel Pressure Fuel Level Throttle Percentage Rudder Angle Fuel Rate Depth Heading Course Over Ground COG Economy Load Percentage Page 47 Veethree Instruments EGM Installation and User Manual Fuel Management Screen The fuel management page data e Fuel rate total e Fuel used total e Trip fuel used e Economy e Fuel level e TimetillO e Distance till O 6 1 Changing the Gauge Display To change the gauge display or customize parameter gauge display on a view page 1 Repeatedly press Key 1 to select a view page on EGM 2 Press Key 2 to select a parameter gauge 3 Press Key 3 to change the gauge data to the currently available data GJ PAGE SELECT Figure 44 Changing the Gauge Display Page 48 Veethree Instruments EGM Installation and User Manual 6 2 Fuel Management Page available via NMEA 2000 and J1939 only screen not shown in analog applications To customize fuel management page 1 Repeatedly press Key 1 to access the Fuel Management page 2 Press a
23. n Alarm 2 Press Key 1 or Key 2 to scroll and view the active alarms 3 Press Key 4 to suppress an active alarm 4 Press Key 5 to return to the main EGM interface Page 51 Veethree Instruments EGM Installation and User Manual 8 About The About page gives software version information and units Software serial number Main Menu User Setup Alarm Setup System Configuration Figure 48 About EGM Main Menu ABOUT PART No CANVU N2KEGM Serial No 1193046 ERS I O SDKC INI FILE 070214WG OS VER B11 K22 RF33 Figure 49 Product Details Page 52 Veethree Instruments EGM Installation and User Manual 9 Glossary Term Phrase Definition Description CANbus Controller Area Network bus is a standard that allows microcontrollers and devices to communicate with each other within a vehicle without any host computer COG Course Over Ground is the actual path of a vessel with respect to the seabed measured in degrees ECU Engine Control Unit is a type of electronic control unit that controls a series of actuators on an internal combustion engine to ensure optimal engine performance EGM Engine Gateway Monitor is a 3 5 display with integrated input and output features J1939 J1939 is an engine data protocol that runs over the industrial CANbus and is used to exchange data between two engines Micro Controller Micro Controller Unit is a chip that contains the Unit pro
24. nd hold down Key 2 to RESET TRIP FUEL This will reset the Trip Fuel Used data to 0 3 Press and hold down Key 3 to RESET ALL FUEL This clears and resets all the counters Fuel Used including Port Starboard Centre and Total Holding down Key 3 will also clear the Trip Fuel counter RESET 5 RESET SIPAGE TRIP FUEL ALL FUEL Figure 45 Fuel Management Page Page 49 Veethree Instruments EGM Installation and User Manual 7 Managing Alarms Veethree EGM has a built in alarm feature that provides visible alarms and warnings when any performance parameter falls below a threshold or exceeds the permissible upper limit When an alarm is active an icon that represents a parameter will flash in red along with a popup warning message in red WARNING Engine Oil Pressure High gt 00 9 PAGE SELECT Figure 46 EGM Performance Alarm and Warning C The Alarms menu is active only if there are any active alarms that have not been viewed and or suppressed The currently supported alarms are e Low Oil Pressure Alarm of 200 kPa 2 bar 29 Psi e High Coolant Temperature of 100 c 212 F e Low Fuel Level of 10 Page 50 Veethree Instruments EGM Installation and User Manual To manage alarms 1 Press key 4 to view the Alarms screen The alarm suppression screen appears Origin Description Engine Hrs FMI Total Active Alarms Figure 47 Viewing and Suppressing a
25. ne Source Address Two DM SPN Version Display Address Figure 26 J1939 Settings Analogue Settings The following analogue parameters can be configured and set using the Analogue Settings menu RPM Calibration Oil Pressure Coolant Temp Boost Pressure Tilt Trim Oil Temp Rudder Angel Fuel Level RPM Calibration RPM calibration is a simple multiplier While the engine is running on idle adjust the number in brackets to the idle RPM specified in the engine manual To configure RPM calibration 1 Press Key 1 or Key 2 to scroll to Analogue Settings highlighted in yellow in the System Configuration menu The Analogue Settings menu appears 2 Press Key 1 or Key 2 to scroll to the RPM Calibration option in the Analogue Settings menu 3 Press Key 4 to select RPM Calibration 4 Repeatedly press Key 4 to set the idle RPM rate Page 32 EGM Installation and User Manual Veethree Instruments Analogue Settings Oil Pressure Coolant Temp Boost Pressure Tilt Trim Oil Temp Figure 27 RPM Calibration B To Configure other Analogue Settings 1 Press Key 1 or Key 2 to scroll to the required submenu highlighted in yellow in the Analogue Settings menu Press Key 4 to select a parameter The analogue parameter screen appears Repeatedly Press key 1 to select the Calibration data box or the Adjust data box Choose WITH GAUGE option if application will use a gauge and the EGM dis
26. nput Page 8 EGM Installation and User Manual Veethree Instruments Secondary Connector DA dew hw Figure 6 Connector PIN OUT Pin Wire Color Black White AN1 Signal Description SENSOR 1 ANALOG INPUT Connect to Oil Pressure Brown White AN2 SENSOR 2 ANALOG INPUT Connect to Coolant Temp Red White AN3 SENSOR 3 ANALOG INPUT Connect to Boost Pressure Orange AN4 SENSOR 4 ANALOG INPUT Connect to Tilt and Trim Pink AN5 SENSOR 5 ANALOG INPUT Connect to Oil Temp Yellow White AN6 SENSOR 6 ANALOG INPUT Connect to Rudder Angle Blue AN7 SENSOR 7 ANALOG INPUT Connect to Fuel Level 10 Violet TACH TACHOMETER INPUT Connect to Tachometer Input 11 Green RS32RX RS232 RECEIVE Connect to GPS NMEA Tx Input Page 9 Veethree Instruments EGM Installation and User Manual 2 Getting Started 2 1 Inthe Box The Veethree EGM box contains the following items Veethree EGM Harness Fitting kit Fixing or mounting template EGM installation and user manual Suncover with Veethree logo If any of the listed items is found missing or damaged contact Veethree Electronics and Marine LLC at techservice veethree com or 941 538 7775 ext 815 2 2 Precautions Follow these safety precautions before installing Veethree EGM Ensure that all el
27. nus CAN Viewer UART Viewer e 10 Debug Screen Data Viewer Frame Counter To access Diagnostics Menu 1 Press Key 1 or Key 2 to scroll to the Diagnostics Menu highlighted in yellow in the System Configuration menu 2 Press Key 4 to select the Diagnostics Menu The Diagnostics menu appears Diagnostics Menu UART Viewer IO Debug Screen Data Viewer Frame Counter Figure 30 Diagnostics Menu A CAN Viewer The CAN Viewer displays the raw CAN data that is received and sent Both CAN PORT 1 data and CAN PORT 2 data can be viewed in this viewer To view raw CAN data 1 Press Key 1 or Key 2 to scroll to the CAN Viewer submenu highlighted in yellow in the Diagnostics menu 2 Press Key 4 to select CAN Viewer Page 35 Veethree Instruments EGM Installation and User Manual The CAN Viewer screen appears CAN PORT 1 Figure 31 CAN Viewer Press Key 1 to pause data recording 4 Press Key 2 to change the port 1 or 2 if required Press Key 3 to select LOG The log screen appears CAN PORT 1 Figure 32 CAN Viewer Log Screen 6 Press Key 3 to clear the log 7 Press Key 2 to change the port 1 or 2 if required 8 Press Key 1 to start recording the CAN data Page 36 EGM Installation and User Manual CAN PORT 1 10 11 Veethree Instruments Figure 33 CAN Viewer Recording Screen Press Key 1 to stop recording Press Key 5 to save and return
28. onnection C There are two Black wires any one of these wires can be used for power connection An inline fuse rated at 500 mA or 1A max must be provided to protect the wiring and the display 3 5 Data Input Connections 3 5 1 Connecting to NMEA 2000 Optional C Before connecting the display to the NMEA 2000 check if an NMEA 2000 backbone is fitted on the vessel 1 Connect the NMEA 2000 DeviceNet cable from the display to the backbone using the T fitting 2 Check if the NMEA backbone is terminated properly This is done by finding each end and ensuring that there is an NMEA 2000 termination device at each end of the backbone 3 Connect the NMEA 2000 termination device at each end of the backbone if it is not found to be connected at each end of the backbone Page 13 Veethree Instruments EGM Installation and User Manual 4 If there is a dual station system connect the system to the NMEA 2000 to share the data between EGMs Carry out this step even if you do not have any other NMEA 2000 equipment 3 5 2 Connecting to J1939 Engines CANbus 1 Identify the CAN Low and the CAN High from the engine ECU Refer engine manual for more information Connect the Green wire to the CAN Low Connect the Yellow wire to the CAN High 2 3 C Both the Green and Yellow wires must remain twisted together 4 Check if the J1939 CAN is properly terminated by measuring the resistance between
29. play Due to hardware limitations on a 24V system the Analog Inputs will not function properly when used parallel with other gauges Press Key 2 or Key 3 to adjust the value in Calibration or Adjust data box Press Key 5 to save and return to the Analogue Settings menu Page 33 Veethree Instruments EGM Installation and User Manual Oil Pressure Calibration Adjustment Final Data Value Figure 28 Analogue Settings Fuel Management available via NMEA 2000 and J1939 only screen not shown in analog applications The maximum capacity of the fuel tank size can be configured in the Fuel Management screen To configure the fuel tank size 1 Press Key 1 or Key 2 to scroll to the Fuel Management submenu highlighted in yellow in the System Configuration menu 2 Press Key 4 to select Fuel Management The Fuel Management menu appears 3 Repeatedly press Key 4 to set Tank Size in liters 4 Press Key 5 to save and return to the System Configuration menu Fuel Management Figure 29 Fuel Management Page 34 Veethree Instruments EGM Installation and User Manual C Each display can be connected to only one fuel tank Hence the display can only read one fuel tank sender Diagnostics Menu The Diagnostics Menu displays the complete information that the EGM display is receiving from different networks The Diagnostics Menu contains the following subme
30. rnnnnrnnnvrnnnvnnnvonnnvnnnnrnrnvnnrvrnrnvenenen 15 3 5 7 Connecting to GPS NMEA 0183 Signal 15 3 6 Veethree EGM User Interface mrrnnnrnnnrnnnvnnnvnnvnnvennrennrernrenvrnnrnnvrannrenn 16 3 7 Configuration of System Settings rrrronrnnnnvnnenvnrenvnnenrnnnnrnnnnrnrenrnnnnnnnnn 17 Ss Zed MAIN aE E td ulsteiniebuiun dl unnteujt 18 Chapter 2 User Operation rrnnnnnvnnnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnenen 41 4 User Interface vives cicesccssvinstesessevecssdsaviessavawedasssansecstsiwaccnneine 43 Veethree Instruments EGM Installation and User Manual 5 Interface View Settings rrrnnnnvvvnnnnnnnnnnnnnnnnvvnnnnnnnnnnnnnnnnenen 44 5 1 Adjusting Interface Brightness rrrnvrnnnvnvrnnnrnvrnerernvnnnrenrrenrrnrnerernnene 44 5 2 Selecting View Modes rrnnrnnnnrnnnvrnnnvnnnnvrnnnnnnnnvrennvnnerernsnnnnenrressnnnennnenn 45 6 EGM Display Gaudes uviieaieietdnasse 46 6 1 Changing the Gauge Display rrrrrnvvnnnvrnnnvrnenvrnnnnrnenvrnnnnvnenrrernnrnenvnenn 48 6 2 Fuel Management Page rrnnnrnnnnnvvnvnnnnvnenrnnvnnnnnnvnnenvnnvnnnvnnvnnnnnnvnsenennnnn 49 7 Managing Aarms aasememmeannemeunnasnneiset 50 8 MOM ee ra sarnana eiaa Aa PEAR ASES eee ee ene nee 52 9 GLOSSY E T E T 53 MONON oo cd E E R T 54 Page ii Veethree EGM Installation and User Manual Instruments Table of Figures Figure 1 Veethree EGM Console rnnnrnvnrnrenennnrerenersvrenerrerenerserersereneneene 3 Figure 2 EGM Front View r
31. scroll to the required submenu option in the Engine menu 4 Press Key 4 to select the required submenu option RPM Oil temperature etc 5 Repeatedly press Key 4 to select and set one of the data input options N2K NMEA 2000 J1939 or 1 0 Page 25 Veethree Instruments EGM Installation and User Manual 6 Press Key 5 to save the setting and return to the Data Sources menu Engine Oil Temperature J1939 Oil Pressure N2K Boost Pressure I O Coolant Temperature J1939 Coolant Pressure N2K 1 Figure 19 Engine B Battery Configure the alternator potential to the different data sources in the Battery menu To configure alternator potential settings 1 Press Key 1 or Key 2 to scroll to the Battery submenu in the Data Sources menu 2 Press Key 4 to select Battery 3 The Battery menu appears 4 Repeatedly press Key 4 to configure the Alternator Potential to N2K NMEA 2000 I O or J1939 5 Press Key 5 to save and return to the Data Sources menu Battery Figure 20 Battery Page 26 EGM Installation and User Manual Veethree Instruments C Fuel To configure Fuel Level settings 1 Press Key 1 or Key 2 to scroll to the Fuel submenu in the Data Sources menu 1 Press Key 4 to select Fuel 2 Repeatedly press Key 4 to configure the Fuel Level to N2K NMEA 2000 I O or J1939 3 Press Key 5 to save and return to the Data Sources menu Figure 21 F
32. ser Manual Veethree Instruments J1939 Settings The following settings can be configured in the J1939 Settings menu Source Address One Indicates the source of the J1939 engine Source Address Two Indicates the source of the transmission DM SPN Version Indicates the version number Display Address Indicates the address of the EGM display Speed Source Determines the type of J1939 PGN used to deliver the speed value to the display It can be set to Wheel or Nav To configure J1939 settings 1 Press Key 1 or Key 2 to scroll to the J1939 Settings submenu highlighted in yellow in the System Configuration menu Press Key 4 to select J1939 Settings The J1939 Settings menu appears Press Key 1 or Key 2 to scroll to the required submenu in the J1939 Settings Press Key 4 to select the required submenu Repeatedly Press Key 4 to select a setting Press Key 5 to save and return to the System Configuration menu C Configure Source Address Two as GLB to indicate that the display accepts data from any source C Configure the Source Address Two option only when an alternator is used C Consult your engine supplier for the appropriate SPN version if you have problem reading alarm data C In single engine setup the default display address is always 40 It is SAE recommendation Page 31 Veethree Instruments EGM Installation and User Manual J1939 Settings Source Address O
33. sreneronesrerennrrerenernereresrserenesrereererenesseresesserenenne 6 Figure 3 EGM Side View srrroronrnrrroronenrorenernerrnensererenenrersersrenerserenensersnenne 7 Figure 4 EGM Rear View uenrrervrrerenerrerenereerenensererenesrerserevenesserenesserenenne 7 Figure 5 Connector PIN OUT nrererenvrrvrenrrrererernrrerersrserenessersrreresessenenenne 8 Figure 6 Connector PIN OUT neererennsrerenrrrererernrrerersrrerenesserseseresessenenenne 9 Figure 7 Mounting Template for Flush Mount Dash Installation 11 Figure 8 Mounting Template for Through the Dash Installation 12 Figure 9 EGM User Interface nr sonsvvvervrvrrenerrererernrrerererserenserenersenenenne 16 Figure 10 User Setup nverenvernnorvernnenerrereservnrnersenenesrenessenenerserenesssrenenne 18 Figure 11 Language Setting mrononnnvvrvnnrerenenrrenernrrerenensernererenessenenenne 19 Figure 12 Key Tone Setting mrarvrnnrnvvrernrrerenenrererernrrerennrsennsrerenessenenenne 19 Figure 13 Measuring Units Settings rmrerrnrnvrrvrenrnrvrrnrrrrenersrrererserenenne 20 Figure 14 Max RPM and Max Speed Settings rrrrrrrrrrrvrrrrrronenenrerenn 21 Figure 15 Alarm Setup doriis insansan 22 Figure 16 System Configuration Menu eernsvrrennrrerenenrerernrnrrererenserene 22 Figure 17 Engine ID Selection ou eeccesceceeseteeeeceeeeeseseeeeeeeetseneeeeaees 23 Figure 18 Data Sources Menu r sernsverenvrerenvrrererereer
34. tings Configure the Fluid Level Instance and Gateway in the NMEA 2000 Settings menu A Fluid Level Instance and Gateway 1 Press Key 1 or Key 2 to scroll to the NMEA 2000 Settings submenu highlighted in yellow in the System Configuration menu Press Key 4 to select NMEA 2000 Settings The NMEA 2000 Settings menu appears Press Key 1 or Key 2 to scroll to the Fluid Level Instance option Repeatedly press key 4 to configure Fluid Level Instance to 1 2 or 3 Press Key 1 or Key 2 to scroll to the Gateway option Repeatedly press Key 4 to select Enabled or Disabled The Enabled option will transmit all the data which the display received over the NMEA2000 network The Disabled option will not transmit any data over the NMEA2000 network Press Key 5 to save and return to the System Configuration menu Page 29 Veethree Instruments EGM Installation and User Manual NMEA 2000 Settings Gateway Enabled Figure 24 NMEA 2000 Settings NMEA 0183 Settings To configure Baud Rate 1 Press Key 1 or Key 2 to scroll to the NMEA 0183 Settings submenu highlighted in yellow in the System Configuration menu 2 Press Key 4 to select NMEA 0183 Settings The NMEA 0183 menu appears 3 Repeatedly press Key 4 to choose and set the appropriate Baud Rate 4 Press Key 5 to save and return to the System Configuration menu NMEA 0183 Figure 25 NMEA 0183 Page 30 EGM Installation and U
35. ue 5 R 0 000 Oil Temp 0 000 Analogue 6 R 0 000 Rudder Angle 0 000 Analogue 7 R 0 000 Fuel Level 0 000 Supply V V 0 000 0 000 Battery 0 000 Figure 36 IO Debug Screen Analogue Inputs Page 38 Veethree Instruments EGM Installation and User Manual Outputs Description Gain Offset Input Final Digital 1 1 ie 0 0 Digital 2 1 fe 0 0 Digital 3 Tach 4 te o 0 Engine hours 1 0 0 o Figure 37 IO Debug Screen Outputs D Data Viewer The Data Viewer screen displays the data such as Units source and Add that the display is reading from networks To view data in the Data Viewer 1 Press Key 1 or Key 2 to scroll to the Data Viewer submenu highlighted in yellow in the Diagnostics menu 2 Press Key 4 to select Data Viewer The Data Viewer Screen appears 3 Press Key 1 and Key 2 to scroll up and down the data rows in the Data Viewer screen 4 Press Key 5 to save and return to the Diagnostics Menu Data Viewer Description Units Source Add RPM Oil Temperature Oil Pressure Boost Pressure Coolant Temperature e Coolant Pressure Load Percentage Torque Percentage Tilt Trim onannoooo Figure 38 Data Viewer Page 39 Veethree Instruments EGM Installation and User Manual Restore Defaults The custom or system specific configuration can be restored to company default settings and to enable re configuration Note that all settings except engine hour setting
36. uel Level D Speed Configure the following parameters in the Speed menu e Speed e Water Speed e Depth e Heading e Mag Variation e Depth Offset e Course Over Ground To configure Speed settings 1 Press Key 1 or Key 2 to scroll to the Speed submenu highlighted in yellow in the Data Sources menu Press Key 4 to select Speed Press Key 1 or Key 2 to scroll to the required submenu option in the Engine menu Page 27 Veethree Instruments EGM Installation and User Manual Press Key 4 to configure the selected submenu to N2K NMEA 2000 I O or J1939 a a The Speed option in the Speed menu can be configured to N2K NMEA 2000 N183 NMEA 0183 or J1939 The Course Over Ground option in the Speed menu can be configured to N183 NMEA 0183 N2K NMEA 2000 and Demo Press Key 5 to save and return to the Data Sources menu Speed Water Speed Depth Heading MET RENE ea Depth Offset Figure 22 Speed E Rudder Angle To configure Rudder Angle input 1 Press Key 1 or Key 2 to scroll to the Rudder Angle submenu highlighted in yellow in the Data Sources menu Press Key 4 to select Rudder Angle Press Key 4 to configure Rudder Angle to N2K NMEA 2000 I O or Demo Press Key 5 to save and return to the Data Sources menu Page 28 EGM Installation and User Manual Veethree Instruments Rudder Angle Figure 23 Rudder Angle NMEA 2000 Set
37. unit or other devices EGM converts displays and retransmits NMEA2000 engine data measured from traditional analogue engine sender signals or from J1939 NMEA2000 Page 4 EGM Installation and User Manual Veethree Instruments EGM as an analogue to NMEA2000 gateway replaces the need for expensive dedicated converter modules It provides the user a full color interactive engine monitor screen that can be used instead of or along with the traditional gauges Hardware 1 2 Product Specification Micro Controller Unit Processor is Free scale iMX 286 at 454 MHz FLASH Memory 128 MB Display a Si TFT LCD 3 5 Resolution 320 H x 240 V QVGA Active Area 70 08 mm H x 52 56 mm V Viewing Angle 130 110 degrees from 6 O clock Number of Colors 64 K Contrast Ratio 300 1 Brightness 750 NIT cd m2 Full sunlight readable Power Requirement 10 V to 32 VDC Sounder Internal Buzzer Connection Two 12 Pin Deutsch DT04 12P Molded in receptacle Communication Environmental RS232 2 CAN BUS 2 0B USB 2 0 Case Material Operating Temperature 20 C to 70 C Storage Temperature 30 C to 80 C Degree of Protection IP 67 ABS Case Color Anthracite Grey Dimensions 95 mm W x 95 mm H x 23 mm rear D Page 5 Veethree Instruments EGM Installation and User Manual 1 3 Dimensions Front View 3 75 OUTLIN
Download Pdf Manuals
Related Search