F+D GmbH - F+D Feinwerk
Contents
1. Initial Start Up 2 Initial Start Up 2 1 Preparation of Location Location of installation must be even and stable Please allow sufficient room e to connect the cables and e to operate the printer The printer has to be used according to the conditions of operation for which the printer was conceived 2 2 Security Advice ze e The housing or the interior of the printer are not allowed to come into contact with liquids e Before operating the printer please make sure that your mains supply is operated at 230V 50 Hz or 115V 60 Hz e n order to avoid the risk of an electric shock do not remove the cover The interior of the PRO 300 does not contain any parts to be serviced by the operator e Maintenance work can only be effected by qualified service personnel e Incase the printer is not used for a while remove the mains plug from socket Always remove on the plug never pull at the cable e Interrupt operation immediately if liquids or parts enter the interior of the PRO 300 Shut off at the mains plug and inform qualified service personnel e Before transporting the printer all paper and transfer ribbon rolls must be removed e To drive the printer via centronic interface the enclosed delivered cable or an equivalent printer cable according to the IEEE 1284 specification the single conductors are twisted two by two and twice shielded must be used 2 3 Unpacking After unpacking the printer pl2. 6000 steps The Image Abort forces an abort of the printing process This is sensible if at the end of an image area there are only blanks The image abort encourages the image creation at high printing speeds Parameter d image abort 12 mm in number of motor steps automatically image abort d 0000 Display 0000 dot 002 The Printer automatically find out the image abort to get the best printing Paper End 000 999 steps In case that within the set step no new label is recognized the error message Paper End will be displayed Parameter d paper end 12 mm in number of motor steps Paper Jam 0000 6000 steps In case that within the set step no paper end is recognized the error message Paper Jam will be displayed Parameter d paper jam 12 mm in number of motor steps Without Label Synchronization There will be no check if paper jam incurred With Label Synchronization F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 17 Operating Dispensing Position 000 999 steps To the position of the start of the label an additional forward feed is effected in order to remove the previously printed label Parameter d dispensing position 12 mm in number of motor steps After each dispensing operation and after the label has be
3. Transfer cutter Transfer can be applied in combination with all other components not present present In case transfer is logged on a monitoring of the transfer ribbon is PRINTER SPECS effected as well as the drive of the transfer ribbon rewinding device transfer Transponder For describing of Transponder the hardware RFID Device option must be existing PRINTER SPECS not present transponder present The Transponder is described before printing at the same moment a writing control is executed With successful describing there sounds a short signal sound and with PRINTER SPECS a write error there sounds a long signal sound with indicating of the RS232 error In the error case the label is not printed RS232 4800 9600 19200 38400 baud 7 data bits 8 data bits 1 stop bit 2 stop bits without parity even parity odd parity without XON XOFF with XON XOFF PNP When you switching the PC on and the printer is connected the driver installation is started automatically yes Plug and Play is active transport direction transponder label no position of the antenna to the label Plug and Play isn t active F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 21 Operating USB Mode During the use of the Windows
4. Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 11 Operating 3 2 Main Menu Mode This menu is called up by depressing the MENU key Depressing the key for only a short time skips to the start of the menu Depressing the key longer skips directly to that option of this menu where it has been exited from last time The menu is exited by depressing tne MENU key After call up ofthe menu the menu display is shown and the functions of the keys are different The first line of the LCD screen displays the first main menu Scrolling the main menu is effected with the v key Main menus are always displayed in the first LCD line and also in capital letters In this example the main menu PRINTER SPECS is indicated PRINTER SPECS The menu can be exited by depressing the MENU key PRINTER SPECS CHARACTER LCD 3 3 Sub Menu Mode General With the gt key the displayed main menu can be skipped In order to display the various sub menus of the chosen main menu continue to depress the P key Sub menus as long as they are not chosen are displayed in the 2nd LCD line in capital as well as small letters For this example the main menu LABEL DATA has been chosen and the sub menu Number of Labels The menu can be exited by depressing the MENU key By depressing the key the displayed sub menu is chosen In order to display the various options of
5. 8 10 12 14 Arial 6 8 9 10 12 14 16 18 as well as by steps up to 255 Code 2 of 5 Interleaved Code 39 Code 128 EAN 8 EAN 13 EAN 128 PDF 417A Barcodes variable in height module width and ratio Optionally with control line check digit subscript line and start stop code line box with varying line widths 2 level technology for fixed and variable objects text barcode logo All objects can be copied into the image memory in transparent non transparent mode Text as well as barcode objects can be placed precisely and indexed numerically Intel 32 bit 8 MB Parallel IEEE 1284 ECP RS 232S 4800 38 400 baud 6 operation keys 2 x 16 digit LCD 2 LED s Thermal paper standard paper plastic foils self adhesive and cardboard labels label height 10 500 mm Label width 30 110 mm paper guide way centred to the thermal print head outer diameter 140 mm max core diameter 12 40 and 50 mm Length max 450 m width max 110 mm roll diameter max 75 mm core diameter 25 4 mm Yes Paper and ribbon end synchronization scan through optical sensoring HxWxDinmm 275 x 250 x 351 9kg 230 115 V auto switch 50 60 Hz Current 1 1 2 2 A fuse T 3 15 A 10 45 C 20 80 humidity non condensing Label dispenser cutting device RFID Device internal and external rewinder Windows 95 98 NT 4 0 2000 und XP Labelling Software SprintLabel F D also supplies custom tailored consumables such as thermal papers la
6. Select Installation fortsetzen hat den Windows Logo Test nicht bestanden der die Kompatibilit t mit Windows XP berpr ft warum ist dieser Test wichtig Das Fortsetzen der Installation dieser Software kann die korrekte Funktion des Systems direkt oder in Zukunft beeintr chtigen Microsoft empfiehlt strengstens die Installation jetzt abzubrechen und sich mit dem Hardwarehersteller f r Software die den Windows Logo T est bestanden hat in Yerbindung zu setzen Installation fortsetzen Installation abbrechen 4 F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 26 User Manual PRO 300 Maintenance Hardwareupdate Assistent A m 8 Select Fertig stellen Fertigstellen des Assistenten Die Software f r die folgende Hardware wurde installiert Klicken Sie auf Fertig stellen um den Yorgang abzuschlie en Fertig stellen Running Update 1 Connect the printer via USB port to the USB port of the PC 2 While switching on the printer please press the buttons lt CUT gt lt CLEAR gt to reach the programming mode The display will show PROGRAM UPDATE Please copy the files to the hard disk Then activate the MS DOS mode at the PC or use the file Update bat position 6 is inapplicable then D Om P w Now the new version can be load to the printer u
7. This screen see picture opposite should always be displayed when printer is switched on Meaning of the status symbols gt XON status l XOFF status no label set edited a label set edited 1 Macro 1 active Number of labels which still have to be printed by the actual label set Menu Screen Will be opened when MENU key is depressed Inside the menu structure the upper line shows the main menu and the lower line shows the sub menu Error Screen Is displayed by the printer in case an error incurred Status Screen Will be displayed when STATUS key is depressed By depressing the key again the second part of the status window will be displayed By depressing the key anew the standard screen will be displayed or in case of an error the error listing is displayed see Software Manual Status Message PRO 300 S02 V2 02 DEVICE 1008 00 0000 0131072 31 10 2001 D ECP 1 Status Screen 2 Status Screen F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 10 User Manual PRO 300 Operating 3 1 2 Power and Error Display Power Display This display is green and lights up in case the mains switch of the printer is switched on Error Display This display is red and lights up or blinks in those cases the error screen is active 3 1 3 Keys PRINT key Of the actua
8. a sub menu the key is depressed furthermore Current active settings are marked with a hook and most of the time also displayed as first option For this example the main menu LABEL DATA has been chosen and the sub menu Number of Labels LABEL DATA Copies The menu can be exited afterwards via key and then by depressing the MENU key SAVE key If an option is selected it can be taken over with the SAVE key and stored in the current macro A confirmation will be displayed for about 2 seconds on the screen After storage this menu option will automatically be exited In case the stored value should be checked afterwards this can be effected by depressing the key The menu can then be exited by depressing the key and then the MENU key F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 12 User Manual PRO 300 Operating Input of numerical values A menu option can also mean a further choice of different options Alternatively at this point a numerical value could be expected to be input according to the actual menu The PRO 300 places a simple editor at your disposal Example Change the number of labels from 10 to 60 Copies Input Key to call up editor 0540 l i Copies Input key for first numerical position lt 0 gt Copies Input key for next numerical position
9. copy macro store it with the SAVE key Thus the macro is stored macro 1 gt 2 Init Macro With it you put back the macro 1 2 or 3 on the default values init macro of macro 0 0 gt 1 Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH Fo Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de 16 User Manual PRO 300 Operating 3 3 4 Label Data Copies 0000 9999 Number of labels to be printed Image Width 0000 1280 dots Image Width determines the width of the print area LABEL DATA copies LABEL DATA image width LABEL DATA image hight LABEL DATA image abort LABEL DATA paper end at LABEL DATA paper jam at LABEL DATA dispensing pos LABEL DATA cutting pos LABEL DATAv TOF Offset The input value must be larger than the label height in dots otherwise an unauthorized paper end error message will be given Parameter d image width 12 mm in number of dots minimum width 5 3 mm d 64 maximum width 106 6 mm d 1280 The value for the image width can at any time be smaller than the real label format The resulting print area will thus be in image middle Image Height 0000 6000 steps Image Height determines the height of the print area Parameter d image height 12 mm in number of motor steps minimum height 10 mm d 120 maximum height 500 mm d 6000 Image Abort 0002
10. lt 00 gt Se Copies Input key for next numerical position lt 000 gt Input key for actual digit depress key 6x u Copies Input key for next numerical position lt 0060 gt Input key to exit editor In case the number is incorrect the editor can be called again by depressing the key once again The option is exited either by depressing the gt key or the SAVE key F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de PRO 300 ok press MENU PRINTER INFOS MACRO NAVIGATER LABEL DATA PRINT PARAMETERS PRINTER SPECS CHARACTER LCD 3 3 1 Menu and Parameters print status boot macro 0 3 macro 1 macro 2 macro 3 macro 0 0000 heating time tph 30 to 30 printer mode no print key with print key multilingual Firmenadresse copy macro macro 1 gt 2 1 gt 3 macro 2 gt 3 2 gt 1 macro 3 gt 1 3 gt 2 image width 1184 dot 98 mm printing speed 75 mm s 300 mm s aut papersensor start USA England Germany Denmark France Sweden Italy Netherlands barcodes EAN 8 13 C_205_ C_39 macro 0 gt 1 macro 0 gt 2 macro 0 gt 3 image height 0714 dot 59 mm synchronisation no with FF no no FF yes with FF man papersen
11. not the case with pure hardware errors Here the user has to contact the Service Department HARDWARE messages cannot be deleted via CLEAR key Reaction of the red LED blinking constantly The first display line contains the error category and the error number the second display line hints at a possible error source HARDWARE 240 cutter Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 33 Accessories Options 7 Accessories Options F D Order Form Fax 49 0 6229 70067 Customer AE Name EE Eegen Ee en Tele eier Printer nee ee Spare part Amount Description Remarks Article No Cutting Device complete 3073 01 735 30 40 Dispenser complete 3073 01 835 30 40 Rewinding Device with fixing screws 3073 01 889 90 40 Thermal Print head with pre assembled adaptor 3073 01 762 90 40 Serial Cable 2m DB9 DB9I 3073 01 921 40 40 2m DB9 DB25 3073 01 922 40 40 m DB9 DB according to customer 3073 01 914 40 40 Parallel Cable 2m _ Centronics 9120 11 303 20 00 Cleaning set 3069 01 301 90 40 Foils and Papers Recommended by F D Amount Size Transfer Ribbon Remarks Article No width long 100 x 200m F13 black Resin max 100mm s
12. printer will be displayed here You can print the barcodes select font by using the SAVE key Logos All logos stored in the printer will be displayed here You can print the select logo by using the SAVE key PRINTER INFOS Insert data fonts Amount of data submitted to the PRO 300 The amount is displayed in a hexadecimal number Warnings PRINTER INFOS Details of warnings including confirmation possibilities logos PRINTER INFOS insert data PRINTER INFOS warnings Print out stored label set Barcodes fonts logos and labels stored in the printer can be printed out easily and is described below 1 Go to menu Printer Infos Labels PRO 300 ok gt g1 2 Depress the button in order to chose the desired label 0000 3 Confirm your choice by depressing the SAVE key The menu will be exited and the label will be printed at the same time a black shape appears on the LCD left of the 1 in accordance to the set macro 4 Depress the PRINT key again for a short time in order to print a further label F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 15 Operating 3 3 3 Macro Navigater What is a macro With the printer a macro means a fixed set of printer characteristics such as transfer printing heating time cutting device etc All parameter which are c
13. 110 x 450m F40 black Resin Wax max 250mm s 3070 99 801 90 89 60 x 450m_ F41 black 3070 99 802 90 89 110 x 400m F42 black Wax max 300mm s 3070 99 803 90 89 60 x 400m F43 black 3070 99 804 90 89 Thermal Label 100 x 60 THE Top D 1200 R Standard max 100mm s 100 x 60 THE Top U 1200 R Highspeed max 300mm s Thermal Paper endless 110 x 250m TP F9 Standard max 100mm s Thermal Transfer 100 x 60 __ Gloss 1500 R with F40 F41 F42 F43 3070 04 506 40 89 75 x 46 Gloss with F40 F41 F42 F43 75 x 46 Alu with F13 Transfer white with F40 F41 F42 F43 with F40 F41 F42 F43 F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 34 User Manual PRO 300 Technical Data 8 Technical Data Printing Method Print Resolution Printing Speed Print Width History Control Fonts Font Sizes Barcodes Drawing Capability Specialities Processor RAM Interfaces Operation Panel Labelling Material Transfer Ribbon Label Reverse Monitoring Measurements Weight Electrical Environmental Conditions Options Driver Software Thermal Direct or Thermal Transfer Printing 12 dots mm 300 mm sec 106 6 mm Hardware 2 internal bitmap fonts Courier bold Arial bold optional bitmap fonts loadable Width and Height 2 6 mm Courier 6
14. Feinwerk und Drucktechnik Ihr kompetenter Partner f r Thermodrucksysteme User Manual Label Printer PRO 300 User Manual PRO 300 Introduction Contents Ee ee EE 4 2 RANA Start D DEE 5 2 1 Preparation of Location 5 2 2 Security AQVICC s EE 5 2 3 ONPACKING EE 5 2 4 Connection Of Mains Cable s eccisessceneirrin i nnie Aiie A AAEREN A AEEA iE EEE 5 25 Insertion of Paper and Transfer F ibbon aaa 6 20 Phintout ta Test Label cornrne a A ees 7 21 EE 7 2 85 Soral MaN CO E Ee 8 2 9 gt SSB Interface en EE 8 2 10 Transporting the Printer 12 icichiinit ae wie ie ee de es 8 3 Operating E 9 31 Control Panel EE 9 Sibel ee RE EE 9 3 17 2 Power and Error DiSplay essere repra eee eeeeena nee eeeceeeaaaeeeeeseeeaaaaeeeeeeeeeaaeeteeeneeaaas 10 31 3 E 10 3 2 Main Men Mode len nenne an hen enden 11 3 3 Sub M nu Modo nn na A AAS 11 3 3 1 Menu and Pararnete rs seirene onnea Een EAA AE EEEE eaa AEEA EERE REER 13 dee Printer INOS eege ae AEE EE 14 3 3 3 EE TEE 15 3 3 4 Label Data uni ege Reeg ge EENS gees 16 3 3 5 Print Parameters EE 18 336 Printer SPECS a ern fen nn onen 19 3 3 72 Chancer LOD EE 22 e EE Ee 23 4 1 Ribbon and PDaperChangoig ern 23 4 2 Cleaning of the Thermal Print Head 23 4 3 Cleaning of the Feed t olers 211 ccscccccecccccsnsceeeensesesceneeesanaaeecsanaeaeaenessesanaeestenaeseseninsttsaaes 23 4 4 Changing of Thermal Print Head 23 4 5 Update o
15. ally at least 2 labels have to be transported unprinted As with the previous point but when switching the printer on no forward feed will be effected Queue Processing no yes with FF This setting is necessary for label paper with index marking Each label will be synchronized to the label start FF will effect a forward feed to the next label Paper jam as well as paper end will be checked subject to the input values When switching the printer on a forward feed will be effected to the next possible label With labels smaller than 60 mm yes Normally the printer parameter can either be sent before or after the label set Thus giving the possibility of subsequent changes of the settings In case there are more label sets in the input memory queue no definite allocation of the printer parameter between the 2 label sets is possible any more Thus the printer parameter of the following label set could circumstances permitting influence the actual label In order to avoid this the following menu points must be observed Menu PRINT PARAMETERS sub menu Queue Processing chose option yes By depressing the SAVE button the option is saved and if required be stored in the macro With this setting printer parameter will only be processed before the label set Only after the desired number of labels is printed the evaluation of the following printer parameter including the new set of labels takes place F D Feinwerk und Dru
16. aper transfer ribbon combination not suitable apply combination as preset by manufacturer or determine by tryout Inside the printed image small islands are not printed e Dust particles on the paper lift the print head at this point and prevent the printing e Adamaged printer roller leading to a lack of pressure at this point The unit must be sent to F D for repair see 2 10 Printed image too weak on one side e Thermal print head has to be adjusted anew horizontally e Adjust contact pressure spring of thermal print head Unprinted stripes run diagonally over the printed image e Reason is the formation of folds in the transfer ribbon e Check guidance of thermal ribbon e Adjust roller with thermal transfer ribbon laterally until ribbon is fold free e Remove unwound ribbon and re insert thermal transfer ribbon e f thermal transfer ribbon crinkles considerably the heating time is set too high and thus also leads to formation of wrinkles reduce heating time e In case winding and re winding device are no longer parallel they have to be adjusted anew F D Feinwerk und Drucktechnik GmbH FD KirchenstraRe 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 31 Service Diagnosis 6 2 Error Correction Error Description Reason for Error Error Correction No green LED Mains Cable Chang
17. ationstechnik EG Richtlinie EMV 89 336 EWG Elektromagnetische Vertraglichkeit EN 55024 1998 St rfestigkeit Einrichtungen der Informationstechnik EN 55022 1998 Funkst reigenschaften 7 j RI wm S d D Sa Neckarsteinach den 16 12 2002 e D CO Uwe Stanitz Gesch ftsf hrer F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 36 User Manual PRO 300 Index 10 Index Auto Gate 21 Carrier Foil Rewinding Device 28 Changing of Thermal Print Head 23 Character LCD 22 Cleaning of the Feed Rollers 23 Cleaning of the Thermal Print Head 23 Communication driver seeseennsennennnnennnn 25 Control Panel cine dran 9 COPIES secin eeen E E 16 Cutting Device u uccnensnnenenennennnnennnnn 20 28 Cutting Positon nennen 17 Ren E EE 19 Dispensing Device cc ccceeeeeeeeeeeeeeeeenneeeees 28 Dispensing Position 17 Error Correction ccrann 31 External Rewinder Wimder 29 Front Rewinder 00 ccccccccccecceeeeeeeeeeeeeeeeeeeeeeeees 28 Hardware Modtications 28 Heating Time TPH u 18 Image Abort and 16 Image Height 22 44 16 Image WIG EE 16 Improvement of the Printing Quality 30 Insertion of Paper ssneeesen
18. ax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 27 Maintenance Running Update 1 2 oar o Connect the printer via serial port to the serial port of the PC While switching on the printer please press the buttons lt CUT gt lt CLEAR gt to reach the programming mode The display will show PROGRAM UPDATE Please copy the files to the hard disk Then activate the MS DOS mode at the PC or use the file Update bat position 6 is inapplicable then Now the new version can be load to the printer under MS DOS using the command mode com1 9600 n 8 1 copy b Dateiname comx for example copy b PEDS2100 upd com lt Enter gt During data transmission the display shows READ DATA CHECK DATA und WRITE DATA When data transmission is finished the printer will be restart Now the new software is available in the printer F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 28 User Manual PRO 300 Hardware Modifications 5 Hardware Modifications 5 1 Thermal Direct Printing The direct printing requires special thermal direct paper which reacts to temperature due to special pre treatment This enables the printing without colour ribbon but it is sensitive to light heat and various chemicals 5 2 Transfer Devi
19. bels and transfer ribbons F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 35 Declaration of Conformity 9 Declaration of Conformity F D Feinwerk und Drucktechnik GmbH Kirchenstr 38 69239 Neckarsteinach EG Konformit tserkl rung Die Ger te mit der Typenbezeichnung PRO300 sind Etikettendrucker die nach dem Prinzip des Thermodirektdruckes zum Bedrucken von thermosensitiven Materialien oder als Thermotransferdrucker mittels Thermotransferfolie zum Bedrucken anderer Materialien eingesetzt werden Hiermit erkl ren wir f r das nachfolgend bezeichnete Ger t aufgrund seiner Konzipierung und Bauart sowie in der von uns in Verkehr gebrachten Ausf hrung bei Einsatz innerhalb der in der Betriebsanleitung vorgegebenen Grenzen die Konformit t gem der Richtlinien 98 37 EG 73 23 EWG sowie 89 336 EWG des Rates zur Angleichung der Rechtsvorschriften der Mitgliedsstaaten Bei einer nicht mit uns abgestimmten Anderung der Maschine oder des Verwendungszwecks verliert diese Erkl rung ihre G ltigkeit Ger tefamilie PRO300 Angewandte EG Richtlinien und Normen EG Maschinenrichtlinie 98 37 EG Sicherheit von Maschinen EN 292 T1 u T2 1991 A1 1995 EG Niederspannungsrichtlinie 73 23 EWG Sicherheit von Einrichtungen der EN 60950 1992 A4 1997 Inform
20. bon round rewinding device Insert clamp strap into the groove and hole Turn the rewinding device one full circle clockwise and thus tension the transfer ribbon Hinge printer device down and secure again Notice The shiny side of the ribbon must point towards the thermal print head The somewhat more dull side is the colour layer which must point towards the paper Synchronization NO BON Za Recognition of label start is effected via scan through light barrier and requests synchronization marks between the labels The synchronous light barrier has a clearance A 5 mm from the edge of the paper e Therefore the depth D of the synchronization mark should be at least gt i l 6 mm from the left paper edge in order to have an edge radius R of A i less than 3 mm The width W has to be at least 1 5 mm Label i distances or printed synchronization marks could also be recognized if the sensor had been adjusted accordingly D 2 6 Printout of a Test Label Switch printer on Put paper into the printer PRO 300 ok gt g 1 Press the STATUS button 0000 Press the PRINT button The LCD display shows left side of the 1 corresponds to the preset macro a black rectangle Additionally the green power LED is lit 6 Press again PRINT button and the test label will be printed IRUN Notice Please check in advance e Is thermal print head inserted e Is printer device upper closed e Is paper reel an
21. ce A durable printing format is achieved by means of using wax or resin coated ribbons whose colour film is heated by the thermal print head and thus transferred onto the label material The transfer device consists of a retarding winding device and a motor driven rewinding device 5 3 Carrier Foil Rewinding Device Self adhesive labels of paper plastic or metal foil are pre punched on a carrier foil The smooth resin like surface of the label facilitates the removing of the label after the printing process To rewind the carrier foil there exists the option carrier foil rewinding device This device is situated between the printing module and the roller support The carrier foil exits the printing module at the front is directed around the dispensing roller at the lower end of the printing module and then put on the carrier foil rewinding device In case the clamp strap is inserted into groove and drilled hole the rewinding device is turned one full circle anti clockwise and thus the carrier foil is tensioned The maximum diameter is 90 mm 5 4 Front Rewinder The rewinding of self adhesive labels without being removed from the carrier foil is possible with a front rewinder Its semicircular form guides the label paper fold free to the rewinding device inside the printer When rewinding labels up to 25 m of standard material can be rewound In case of rewinding punched material the tensioner must be rotated backwards 5 5 Cuttin
22. cktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 19 Operating 3 3 6 Printer Specs Printer Mode without Print key with print key Printing is only possible by depressing the PRINT key Automatic paper sensor start When switching to another label paper there might incur problems with synchronization should both paper types be very different In order to guarantee a reliable synchronization it might be necessary to carry out the following option Before starting the printout the paper sensor has to be positioned at a part of the label which has not yet been printed In the case of an incorrect measuring the notice ERROR appears on the screen In order that the printer retains the change made when subsequently switched on the new information has to be committed to memory For that you have to select the option manual paper sensor and store it with the SAVE Key Manual paper sensor 0 127 LED For determination of the optimum sensor adjustment mi hysteresis hysteresis STATUS button decrease sensor current CLEAR button increase sensor current S x Proceeding 5 5 The label material has to be positioned with the A carrier in the area of the paper sensor C L 6 The point of switching A determine of after 4 7 The label has
23. d transfer ribbon inserted 2 7 Parallel Interface In order to connect the parallel cable align the wider side of the plug to the wider side of the printer connector Afterwards fasten the plug with the two existing clamps in order to produce a stable electrical contact Then connect the cable to the computer corresponding parallel interface Notice Before connecting the cable the printer and the PC have to be switched off F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 8 User Manual PRO 300 Initial Start Up 2 8 Serial Interface In order to connect the serial cable align the wider side of the plug to the wider side of the printer connector Afterwards fasten the plug with the two existing screws in order to produce a stable electrical contact Then connect the cable to the computer corresponding serial interface The serial interface also serves for communication with the PC but it is slower than the parallel interface By using the keyboard you can set Baud rate 4800 9600 19200 38400 Data bits 7 8 Stop bit 1 2 and Parity without with even odd Protocol without XON XOFF with XON XOFF Standard settings are printed in bold Notice Before connecting the cable the printer and the PC had to be switched off 2 8 1 Serial Printer Cable DB9S Printer Sc
24. driver this attitude is not used This attitude is used only for F D programs single Only one printer can be used multi Several printers can be used Auto Status The short status is sent automatically to each printer over the active interface no automatically short status isn t active yes automatically short status is active Key lock To prevent problems you can disable different keys The following keys can be deactivated lt PRINT gt lt STATUS gt lt MENU gt If the menu key is disabled you arrive nevertheless with the combination of keys lt MENU gt and lt STATUS gt in the printer menu F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 22 User Manual PRO 300 Operating 3 3 7 Character LCD Schedule ANSI ASCII multilingual Country USA England Germany Denmark France Sweden Italy Spain Norway Netherlands Update Flashdata Here logos and fonts can be store in the printer The data is transferred via serial or parallel interface For the conversion and implementation of logos the tool FDLogo can be used This is available on the homepage www FuDdruck de Change to the menu CHARACTER LCD Update FlashData Activate the Update mode by pressing the key In the display the following message will be sho
25. e The higher this value the higher the loading on the thermal print head Printing speed Printing speed determines the transportation speed of the label paper within the printing range 75 100 125 150 175 200 225 250 275 or 300 mm s PRINT PARAMETERS heating time tph PRINT PARAMETERS printing speed PRINT PARAMETERS synchronisation PRINT PARAMETERS Queue process more than 1 label will be forward fed yes without FF Synchronization no with FF This setting is required when using endless paper No label synchronization will be effected FF causes a forwarding of the paper according to the set image height Paper end will be detected paper jam not When switching the printer on a forward feed of 1 label will be effected no without FF As with the previous setting but when switching printer on no labels will be lost as no forward feed takes place The PRO 300 assumes that when the printer is switched on the label paper is already positioned correctly If this is not the case positioning can be effected by depressing the FF key several times yes AUTO FF The printer autonomously determines image height paper jam and paper end Afterwards positioning to label start or dispensing position will be effected Labels up to a maximum length of 50 cm will be supported whereas the space between the labels should not be wider than 10 cm Larger distances between the labels will cause a paper error message Norm
26. e Mains Cable Mains Plug Establish correct contact Mains Fuse Change Mains Fuse Internal Power Supply defective Manufacturer Service No printed image Print Parameter incorrect Adjust print parameter anew Transfer ribbon inserted Insert transfer ribbon according to incorrectly drawing Thermal Paper incorrect Use material recommended by manufacturer Transfer ribbon of other quality Use transfer ribbon recommended by manufacturer Label material is transported Dirty Transport Rollers Clean transport rollers see 4 3 insufficiently buckled printed image Label material is not Transport rollers are not driven Manufacturer Service transported at all Transfer ribbon is not Transfer ribbon torn Insert transfer ribbon anew and transported at all depress Print Key Unauthorized Paper Jam Paper Sensor set incorrectly Execute the option Start in menu Paper End Error Message Printer Specs aut papersensor In dispensing mode the label is Paper Jam Bring label into dispensing position retracted before it can be by using the key and remove it taken out remove Dispensing Table if necessary Every error switches the display from the standard window to the error window and activates the error LED It is also possible that several errors occur at the same time for example sequence errors where the error with the highest priority is displayed The priority increases with the increasing error code number Inside the status display up to 8 err
27. ease check contents of the box e Printer PRO 300 e Mains Cable DIN Standard e Centronics Cable IEEE 1284 specification e Sample Reel of Thermal Paper e CD with Printer Driver User Manual and Software Manual 2 4 Connection of Mains Cable At the rear of the printer the connector for mains cable and the mains switch are located e Switch off PRO 300 0 must be depressed on mains switch e Connect mains cable consider firm connection Use earthed socket only e Switch on PRO 300 1 must be depressed on mains switch Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de 6 User Manual PRO 300 Initial Start Up 2 5 Insertion of Paper and Transfer Ribbon Insertion of Paper The label printer is suited to print onto thermal paper Normal paper plastic foil and metal foil can only be printed by using the option transfer device These materials are available on reels or adhesive labels 1 Open the cover and remove the white paper guide disk 2 Push reel onto wind off spindle 3 Push paper guide disk back 4 Unwind some label material or paper respectively and load the material into the right and left paper guide while print head device is opened 5 Adjust paper guide width by the black knurled screw The label material should not be depressed down by this action leave appr
28. en removed the next label will be re positioned to the start of the label The dispensing position will be ignored should the cutting device be logged on Cutting Position 000 999 steps To the position of the start of the label an additional forward feed is effected in order to cut the previously printed label Parameter d cutting position 12 mm in number of motor steps The cutting position describes the distance between the thermal print head and the cutting device This normally lies at 16 6 mm d 200 By changing this value the cutting position can be moved After each cutting operation and before the next printing process the label will be re positioned to the start of the label The cutting position will only be considered should cutting device be logged on TOF Offset 00 99 steps 50 Distance between start of printout to label edge d number of input steps motor steps paper end min a image width image heigth image abord E E D D a Si TOF offset L F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 18 User Manual PRO 300 Operating 3 3 5 Print Parameters Heating Time TPH from 30 to 30 in steps of 5 By this the blackening intensity of the paper is set The higher this value the higher the intensity of black Notic
29. f printer sofiware rn nne nrn nnn nnee en rannen eeen 25 4 5 1 Update via USB interface uunnunnnneennnnnnennnennnnnnennnnnnnnnnnnnnnnonnnnnnnnnnnnnnennnnnnannnnn 25 4 5 2 Update via Parallel mntertace rennet 26 4 5 3 Update via Serial interface o ccccccccccccccccssssceeecesennneceeeeesensneeeeeessssssneeeeessssnseseeeesennaees 26 5 Hardware JEDES esgegeseebeegugesbtorege d Zeie guud SCENE edd neuere Re 28 9 1 Thermal Direct Printing sn nnnnnnnnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnr nn 28 5 2 Transfer Device ernennen ana Kae ernten Eee er hr 28 5 3 Carrier Foil Rewinding Device cccccccceceeseeeeenseeececeeeteseneeeesaaeeseceeeeeteeneeeetanaeeeeeneeteeeaes 28 9 4 Front Rewinder 2 ccccecceccececeeceeeeeeeeeeeeeeeceeeeecs see eaeeaeeaseeaaaaaaeaaesaeeaeeeeeeeeseeeeeeeeseneteeteeteees 28 5 5 Cutting Device nuunesnnnnnnssnnnnnnnnnnnennnnnnnrnnnnnnnnnnnnennnnannnrennnnnnnsnnnrnsnnnnnrenannnnnssnnnnnanannenn 28 9 6 DISPENSING DEV CE cece nteee cette ennne nett ee een anette teeta aaeeeeeeeeeeaaaeeeeeeeeesaaeeeeeeeeeiaaeeeeeeenenaaes 28 5 7 External Rewinder Winder neren ennn 29 5 8 REID DOVICG IEE e ne anne nennen depp theses tape Banken hen Puh bbyap Ne 29 ee 30 6 1 Improvement of the Printing Oualty 30 6 2 Error Ee 31 6 2 1 EmrorLevel EE 32 6 2 2 Emor TE 32 6 2 3 Emor Level 3 ET 32 Fe AceessornesS TEE 33 8 Technical Eeer 34 9 Declaration of ee E 35 10 WOK EE 36 Documen
30. g Device The cutting device separates the label from the rest of the paper stock It is mounted as an attachment to the base plate The connection bush is situated below the printing module in the assembly plate The position of the cut is set up in the menu with reference to the synchronization mark The cutting device can separate paper up to a weight of 180 g m Paper particles should be removed as they could lead to malfunctions when jammed in the rotating knife 5 6 Dispensing Device In the case that the printed labels are directly applied to the object then the dispensing device comes into action The carrier foil is guided around the dispensing edge at 90 downwards and tightened via the dispensing roller and the carrier foil rewinding device Thus the label is peeled and presented on the dispensing table When removed a sensor signal triggers the printout of the next label F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 29 Hardware Modifications 5 7 External Rewinder Winder The external rewinder is an accessory to the label printer which rewinds large label rolls after printing This unit is connected to the printer by means of an adaptor plate The external rewinder can be combined with the external winder if desired to ensure that equally large label roll
31. hangeable in the menu of the PRO 300 can be combined as a macro Otherwise they will be lost when the printer is switched off The PRO 300 contains 3 macros numbered from 1 to 3 With these macros the printer can chose between 3 different fixed configurations The macros are stored in the printer The content of this memory will remain even if the printer is switched off As soon as the printer is switched on that macro set in the boot macro will automatically be loaded into the work area Thus the printer knows all printing options when it is switched on Macro 0 has been preset by the manufacturer as default macro This cannot be changed Macros 1 2 and 3 also contain preset values like macro 0 but these can be changed by the user MACRO NAVIGATER boot macro 0 3 MACRO NAVIGATER copy macro MACRO NAVIGATER init macro The loaded macro will be displayed in the standard display 1st LCD line 16th position Boot Macro 0 3 The actual boot macro will be marked with a hook or displayed in the standard display respectively By depressing the button the desired boot macro 0 3 macro is selected and chosen by depressing the SAVE key With the y macro 1 change of the boot macro the printer is automatically restarted afterwards the new macro is active immediately Copy Macro Around the content of the current macro in another macro to take over you can copy a macro For this select the respective menu option and
32. hirm RxD TxD DTR GND DSR RTS CTS OO JO Om P Gabi gt 1 2 3 4 5 6 7 8 9 2 9 USB Interface To connect the PC with the cable please use the flat side type A of the plug Notice Before connecting the cable the printer and the PC had to be switched off Put now the smaller plug type B of the USB cable on the back of the printer into the intended socket 2 10 Transporting the Printer 1 Switch printer off 2 Unplug carefully the mains cable and the interface cable serial and or Centronics cable 3 Use original packing material for transportation where possible Notice Before transporting the printer all paper and transfer ribbon rolls must be removed F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 9 Operating 3 Operating 3 1 Control Panel The control panel consists of e LCD Screen 2x16 digits e 2 LEDs Power and Error e 6 keys PRINT key FF SAVE key MENU key STATUS V key CUT key CLEAR key 3 1 1 LCD Display The information shown on the display depends on present operating mode of the printer In total 4 different sub screens can be opened Standard Screen This mode displays the actual short status of the printer which is of PRO 300 ok interest during the printing process
33. itch printer off 2 Release the print head upper and rotate upwards 3 Wipe with a special cleaner of F D dampened cloth several times smoothly over the printing dy Notice Do not use any hard or sharp edged objects 4 3 Cleaning of the Feed Rollers Above all paper and dust particles stick to the feed rollers and have to be removed 1 Switch printer off 2 Release the print head upper and rotate upwards 3 Clean feed roller with special cleaner of F D and bobble free cloth 4 After the rollers are dry hinge print head device down and latch Notice Do not use acetone or any other solvents amp 4 4 Changing of Thermal Print Head Notice The thermal print head is a sensitive mechanical electronic and electro static component Do not ze use any sharp edged items and take care that you arenot electro statically charged Electrostatic charges can damage the thermal print head therefore it is absolutely necessary to execute a charge equalization in advance Knurled screw f 1 Switch printer off and unplug mains plug i i 2 Release the print head upper and rotate upwards 3 Unlock knurled screw in the middle of the print head upper and pull print head forwards 4 Disconnect cables 5 Fitthe new thermal print head The thermal print head is pre assembled onto an adapter and also pre adjusted 6 Connect cables to new thermal print head Here the correct positioning of the connector has to be paid attention t
34. l label set one label will be printed FF key Transports the paper through the printer without printing and synchronizes to print start MENU key The menu screen will be displayed This gives the user the possibility to check the set printer functions or change them respectively The menu will be exited by depressing the same key again By depressing this key for a longer time period that particular part of the menu can be skipped to where the last skip back took place During a print job this can be stopped by depressing the key for a while and depressing the key again enables finishing the print job STATUS key The status screen will be displayed In case of an error this key depress key 2x displays the 2nd status screen with up to 8 error codes The menu will be exited by depressing the same key again CUT key Should a cutting device be available this can be activated by depressing the Cut key CLEAR key Functions only when error screen is opened By means of CLEAR key the displayed warning message can be erased In case several errors are indicated at the same time only the warning message with the highest priority at that time will be displayed The CLEAR key can only be depressed for that amount of time until all warning messages are displayed or erased respectively ERROR and HARDWARE messages cannot be erased F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000
35. nder MS DOS using the command usb2prn exe Dateiname Beisp usb2prn exe PRDS2119 upd lt Enter gt 7 During data transmission the display shows READ DATA CHECK DATA und WRITE DATA 8 When data transmission is finished the printer will be restart 9 Now the new software is available in the printer 4 5 2 Update via Parallel interface Please take note that an update is only possible if the present version is 1 13 or higher Running Update 1 Connect the printer via parallel port to the LPT port of the PC 2 While switching on the printer please press the buttons lt CUT gt lt CLEAR gt to reach the programming mode 3 The display will show PROGRAM UPDATE 4 Please copy the files to the hard disk 5 Then activate the MS DOS mode atthe PC or use the file Update bat position 6 is inapplicable then 6 Now the new version can be load to the printer under MS DOS using the command copy b file name Iptx for example copy b PRES2126 upd Ipt1 lt Enter gt 7 During data transmission the display shows READ DATA CHECK DATA und WRITE DATA 8 When data transmission is finished the printer will be restart 9 Now the new software is available in the printer 4 5 3 Update via Serial interface Please take note that an update is only possible if the present version is 1 13 or higher F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 F
36. nnnnennneeennnnnnn 6 Insertion of Transfer Ribbon 7 Key LOCK EE 21 Keesen dE innen 10 Label Dita nennen 16 Main Menu Mode sasseeesneneneenneenreenerressresreene 11 Mains Switch 5 Maintenance 23 Makro Navigater sn 15 Menu and Parameiers eneee 13 r Lu DEET 9 Paper End 16 Paper Jam aiaa 16 Paper Gensor nenn 19 Parallel Interface 7 Plug and Plan 20 Print Stats 14 Print Parametere 18 Printer Mode nennen 19 Printer Infos 14 Printer Spets senneianann dire 19 Printing speed 18 Print out stored label set 14 Programm Update 26 REID Device iirc nica Se nie 29 EE E 20 Serial Interface 8 Service Diagnose 30 Sub Menu Mode 11 Synchronization n s ee eeeeeeeeeeeeeteeaeeeeees 18 Technical Data 34 Test Label rctra see ee aa 7 Thermal Direct Printing 28 TOF Offset eh ana ceceoeinnd Se receeseniatin dee 17 RRE 20 Transfer Device da 28 Transponder 20 Update Logos and Font en 22 Update of printer software s ssssseseenrreee eere 25 F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de to F D Feinwerk und Drucktechnik GmbH Kirchenstr 38 D 69239 Neckarsteinach Tel 49 0 6229 700 0 Fax 49 0 6229 700 67 Mail hotline FuDdruck de Web www FuDdruck de Copyright by F D 3073 02 998 90 06 S
37. o F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 24 User Manual PRO 300 Maintenance 7 Nest the thermal print head from the lower side into the rectangular holes on the prit upper via the tabs 8 Rotate the print head to the upper side ul the thread bush mates with the knurled s 9 In order to tighten the knurled screw dra down the printer upper and lock tab locking of printer upper ES Bm a depending very much on the boundary conditions such as paper quality printing speed heating time Notice Unfortunalety it is not possible to claim for warranty as the lifetime of the thermal print head is quality of thermal ribbon Ae Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH Fo Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 25 Maintenance 4 5 Update of printer software A new printer software firmware can be load via the USB serial or parallel port to the PRO 300 4 5 1 Update via USB interface Please take note that an update via USB is only possible if the present version is 2 06 or higher Hardwareupdate Assistent First install the F D USB Treiber Willkommen This is no printer driver but itisan communication driver Mit diesem As
38. or codes will be displayed in the 2nd status window depress status key 2x The error messages as displayed in the LCD display are divided into 3 categories Error Codes 01 99 WARNING lowest priority 100 239 ERROR 240 255 HARDWARE highest priority Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de 32 User Manual PRO 300 Service Diagnosis 6 2 1 Error Level 1 In this error status all printer functions are still allowed After warning message s have been deleted by depressing the CLEAR key the printout will be started which can be incorrect With this error category most of the time incorrect control sequences or object sequences by the user are the reason As far as possible these are replaced by standard values WARNING messages can always be erased by depressing the CLEAR key Reaction of red LED blinking slowly The first display line contains the error category and the error number WARNING 023 the second display line hints at a possible error source control sequence Deviating from this standard reaction to warnings further possibilities can be set via the menu Menu PRINTER INFOS Warnings confirm This menu corresponds to the above description Warnings are deleted by depressing the CLEAR key Menu PRINTER INFOS Warnings display only Warnings are di
39. ox 0 5 mm play Notice It is important that the distance between the paper and the mounting plate on the paper guide is equal to that on the label reel The reel can be moved easily The paper guide disks should only press lightly against the reels Uneven wound or misaligned label reels lead to printing errors and paper jam The maximum diameter ofthe paper reels on the internal rewinder lies at 90 mm 6 Hinge print head device down and secure Printer Device Upper Paper Guide Disk Lock Rewinder Device for Transfer Ribbon Ma Colour Layer Label Tensioner Rewinder Device for S Optional Label Base Material Printer Device Lower Knurl Screw Paper Guide Label Reel Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 Initial Start Up Insertion of Transfer Ribbon Printers equipped with the option Transfer Device feature a wind off wind on mechanism positioned above the printer upper section see diagram on previous page 1 Push transfer ribbon reel onto winding device below operator panel Centre reel to print head Guide ribbon according to diagram on previous page below the opened printer device upper Wind transfer rib
40. pezifications subject to change without prior notice
41. s Value 37 LED Update FlashDa Send Data COURIOEF COURI14F ARIALOSF AMAL Agr V 000 dot 002 mm Queue process no yes no with print key label taken scrolling no yes FDLogo byteam XXXXH acknowledge display only ignore 70 ignore paper end at paper jam at dispersing pos cutting pos 120 dot 10 mm 6000 dot 500 mm 060 dot 5 mm 200 dot 16 mm o gt TOF offset oe 50 dot 50 FE no not present not present 4800 Baud yes present present 9600 Baud yes always 19200 Baud 38400 Baud USB Mode autom Status yes no lt PRINT gt no yes lt STATUS gt lt MENU gt ER English French German keys and character explanation V key leaf through the main menu P key leaf through the sub menu key select option default V V 14 User Manual PRO 300 Operating 3 3 2 Printer Infos Print Status Print out of all parameter to be set Image width and image height must be set to gt 54 mm 648 dots each You can print the print status by PRINTER INFOS using the key print status Labels All label sets stored in the printer will be displayed here You can print the select label by using the SAVE key PRINTER INFOS Barcodes labels All barcodes stored in the printer will be displayed here You can print the select barcode by using the SAVE key Fonts PRINTER INFOS All fonts stored in the
42. s can be wound and rewound 5 8 RFID Device If one wants to print a label and atthe same moment the chip in the label describe the RFID Device Radio Frequency IDentification is exactly the correct The data transfer between Transponder and reader takes place about the aerial coil without touch Besides the principle of the electromagnetic induction is used The types of transponder Infineon MY D Philips I Code and Texas Instruments Tag it are supported The working frequency amounts to 13 56 MHz F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 20 User Manual PRO 300 Service Diagnosis 6 Service Diagnosis 6 1 Improvement of the Printing Quality Unprinted stripes run over the printed image in printing direction e Dust particles are fixed onto the thermal print head and have to be removed with a special cleaner of F D dampened cloth e Dot failure due to mechanical influence or electrostatic charging the thermal print head has to be changed See maintenance notice change thermal print head Entire printed image too weak e Check printing parameter and change if necessary reduce speed increase heating time e Clean thermal print head with special cleaner of F D dampened cloth when printer is turned off do not use hard or sharp edged items e In transfer printing mode used p
43. sistenten k nnen Sie Software f r die folgende 1 Connect the printer to the USB interface at Hardwarekomponente installieren the PC USB Device 2 Switch on the printer The following A Falls die Hardwarekomponente mit einer CD window appears D oder Diskette geliefert wurde legen Sie diese zer 3 Select Software von einer Liste installieren and Weiter Wie mochten Sie vorgehen Software automatisch installieren empfohlen Klicken Sie auf weiter um den Vorgang fortzusetzen Hardwareupdate Assistent Wahlen Sie die Such und Installationsoptionen ay 4 The following window appears Diese Quellen nach dem zutreffendsten Treiber durchsuchen 5 Select Quel le Verwenden Sie die Kontrollk stchen um die Standardsuche zu erweitern oder 6 Select Weiter einzuschr nken Lokale Pfade und Wechselmedien sind in der Standardsuche mit einbegriffen Der zutreffendste Treiber wird installiert C Wechselmedien durchsuchen Diskette CD Eolgende Quelle ebenfalls durchsuchen Q ADRIVERSUSB_Treiberswin2000_XPSV1 02 Durchsuchen O Nicht suchen sondern den zu installierenden Treiber selbst w hlen Verwenden Sie diese Option um einen Ger tetreiber aus einer Liste zu w hlen Es wird nicht garantiert dass der von Ihnen gew hlte Treiber der Hardware am besten entspricht Hardwareinstallation A Die Software die f r diese Hardware installiert wird F D Label USB Printer for Win2k XP 7
44. splayed as usual but do not have to be confirmed by the user The printing process will not be interrupted Menu PRINTER INFOS Warnings ignore Warnings are neither displayed nor do they have to be confirmed Via status request and status display they can be called in Menu PRINTER INFOS Warnings N ignore 70 Warning 70 character will be completely ignored and is preset as a standard in the printer 6 2 2 Error Level 2 In this status all printer functions are allowed but it can no longer be printed This error category most of the time shows serious label set errors memory overflows or paper errors Paper errors can normally be cleared Other errors require in the main a switching off and on of the printer ERROR messages cannot be deleted via CLEAR key Reaction ofthe red LED blinking quickly The first display line contains the error category and the error number ERROR 185 the second display line hints at a possible error source insert memory 6 2 3 Error Level 3 In this status all printer functions are allowed but it can no longer be printed This error category concerns either an incorrect printer configuration or a hardware error An incorrect printer configuration means for example a logged on cutting device although no cutting device is connected If this is triggered a hardware error message is the result Hardware errors due to incorrect printer configuration can be resolved by the user This is
45. t 3073 02 998 90 06 Revision June 2007 F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de 4 User Manual PRO 300 Introduction 1 Introduction With the PRO 300 you have purchased a professional label printer Developed and produced by F D Feinwerk und Drucktechnik GmbH the PRO 300 sets new bench marks in the field of industrial application of label printers Based on years of experience with the HFP printer line a new generation of printers was created Above all the printing speed 300 mm s as well as the printing quality have been improved considerably In addition many more possibilities for comfort and operation are now at the customers disposal The PRO 300 can be handled simply and easily by means of a LCD display and 6 keys Nevertheless you should take the time to read this user manual in order to be able to use all the possibilities of this printer to an optimum At the beginning you will learn how to initialise this printer After you are familiar with the operation of the printer this manual will render a good service to you for quick reference Please keep this manual safe F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 5
46. to be positioned in the area of the lin paper sensor 0 A l B 127 8 Point of switching B determine of after S sensor N 9 The correct sensor value Z is the mean value of 1st measuring 2nd measuring the two measurements C carrier material scan material L label do not scan material A measuring point 1 B measuring point 2 Z A B 2 Z ideal value Dispensing When dispensing labels the label has to be transported after printing so far so that it can be taken out easily Time of taking the label out will either be monitored by label taken option or by means of operation of the print key Dispensing position 0 corresponds to the positioning at the start of the label In order to be able to take the previous label the value for the dispensing position has to be increased no with print key After the print job is finished the paper will be reset to the dispensing position for enabling the take or tear off of the label After pressing the print key it turns again back in the printing position and the next print order can be carried out with label taken The label taken device can be installed as an option The device ensures that the next label will only be printed if the previous one has been taken out A dispensing position gt 0 always means that the following label has to be repositioned before printing takes place Logging on of the label taken device is only possible label taken without the cutting de
47. vice The dispensing position will be ignored in case the cutting device is logged on Tel 06229 7000 Fax 06229 70067 F D Feinwerk und Drucktechnik GmbH FD Kirchenstra e 38 D 69239 Neckarsteinach E Mail hotline fuddruck de Internet http www fuddruck de 20 User Manual PRO 300 Operating Cutting Device Separating labels by cutting a cutting device option must be installed PRINTER SPECS no printer mode Should a cutting device be connected but not logged on the logging on will be effected automatically when switching the printer on yes The label will always be synchronized to the TOF position Thus during a print job no forward backward positioning has to be effected The motor can run between 2 labels in brakeless mode By means of ESC k sequence a cutting operation at the end of the print job can be activated Furthermore the cutting device can also be triggered via the CUT key The dispensing position will be ignored in case the cutting device is logged on Notice When single labels should be cut off it is important that each label has a minimim height of 25 mm PRINTER SPECS yes always dispensing Each label within a print job should be cut After the printing of a label the cutting position will be driven to cut and only before the next printout takes place the TOF position will be re positioned PRINTER SPECS aut papersensor PRINTER SPECS man papersensor PRINTER SPECS
48. wn gt Data to be transmitted has to be prepared for the printer Activate the MS DOS mode at the PC Now new data can be transmitted with the command line copy b file name Iptx Example copy b logos upd Ipt1 lt Enter gt via MS DOS to the printer mm ko Connect the printer via the parallel interface to the LPT port of the PC CHARACTER LCD schedule CHARACTER LCD country CHARACTER LCD Update FlashData CHARACTER LCD scrolling CHARACTER LCD language FLASH DATA Send Data 8 During the transmission process the message BUSY will be displayed 9 After successful transmission the printer states READY 10 The data is now firmly stored in the printer Scrolling The menue text will be pushed in from aside no yes Lanquage language to choose from menu CHARACTER LCD german english french F D Feinwerk und Drucktechnik GmbH Kirchenstra e 38 D 69239 Neckarsteinach Tel 06229 7000 Fax 06229 70067 E Mail hotline fuddruck de Internet http www fuddruck de User Manual PRO 300 23 Maintenance 4 Maintenance 4 1 Ribbon and Paper Changing Change the paper or transfer ribbon respectively as described under 2 5 4 2 Cleaning of the Thermal Print Head Depending on the application as well as the environmental conditions of the thermal printer the print head must be cleaned every 10 to 20 working hours 1 Sw
Download Pdf Manuals
Related Search