Home

Operating Manual

1. Press a key to quit NOTE this function can be used to start the car with an emergency start Enter the PIN CODE and read the number of keys at the end of the operation the car can be started once excluding the immobilizer function using a key without transponder or with disabled transponder If a wrong PIN has been entered or there are errors during communication the display will show error message No 1 see chap 10 WARNING ERROR MESSAGES 7 4 READING IMMO ID This function is used to view the immobilizer identification ID IMMO a code comprising 14 alphanumerical characters essential for finding the PIN CODE In such cases the PIN CODE is issued by the car manufacturer Select and press ENTER the display will show IMMO ID READING XXXXXXXXX IMMO XXXXXXX XXXXXXX XX Press ESC to quite Only the next 14 characters make up the word IMMO relating to immobilizer identification Press ESC to quit Copyright Silca 2005 31 SDD Operating Manual English 7 5 ERRORS This function is used to check for any anomalies in the immobilizer memory After selection press ENTER the display will show Please wait Present errors NO ERRORS If there are no anomalies in the memory the display will show PRESENT ERRORS NO ERROR DETECTED Press any key Press any key ERRORS FOUND If there are anomalies in the memory the display will show how many XX errors there are in the ce
2. SilcaDiagnosticDevice Operating Manual Code D428885XA Vers 8 0 SDD Operating Manual English 2005 SILCA S p A Vittorio Veneto This manual has been drawn up by SILCA S p A All rights reserved No part of this publication may be reproduced or used in any form or by any means photocopying microfilm or other without the written permission of SILCA S p A Published May 2005 Printed in Vittorio Veneto by SILCA S p A via Podgora 20 Z l 31029 VITTORIO VENETO TV Italy 2 Copyright Silca 2005 Operating manual English SDD INDEX 1 MACHINE DESCRIPTION ie 8 1 1 MAIN CHARACTERISTICS oooccococcocoooocooconooconcooncnnnonnn canon canas 8 12 TECHNICAL DATA tonal iii 8 1 3 WORKING PARTS 9 1 4 SYMBOL ei 10 15 ELECTRICAL ELECTRONIC OIRCUIT ii 11 2 EE 12 li PACO iena 12 2 2 TRANSPORT 12 2 3 UNPACKING cooococcoccococononconoononconnononcnno ono 12 2 4 HANDLING 12 3 ACCESSORIES PROVIDER 13 4 INSTALLATION AND PRERARATION 13 A1 PREPARATION FOR USE INITIAL OPERATIONS 13 4 2 CHECKING FOR DAMAGE 13 4 3 ENVIRONMENTAL CONDITIONS iieii 13 4 4 SOFTWARE UPDATING conoces 13 5 REGULATION AND GAUGING ssessssennssenennsenneosennenenrnensnnreosnnrenenrrrnenrrnnns 13 6 USING THE MACHINE ie 14 ol SURE 14 62 PASSWORD lla 14 6 2 1 PASSWORD MEMORISED 15 6 3 MAIN MENU 15 6 4 IMMOBILIZER MENU 15 6 4 1 SELECTING THE CAR MAKE 16 6 4 2 CAR MODEL NOT ENABLE
3. Keys Mem Number of keys stored in memory PIN CODE if storage is confirmed by an operator IMMO ID Immobilizer control unit ID To enter the data use the T keys to position on the desired item Press gt to enter and select the field where the text is to be typed Press ENTER to confirmed To quit and memorize the data press ESC Is the information InServed COrrect NO gt YES Select YES NO and press ENTER No to return to the data entry window Yes to store the data in the file ERASE SELECTED KEY This function is used to erase a key from the immobilizer The position in the memory where the key has been stored must be known POSITION X Select ERASE SELECTED KEY from the menu and press ENTER the display will show ERASE SELECTED KEY Avallable key to erase dea WLECE Ee Eet This screen shows the position in the memory occupied by keys that operate on the car Digit the position in the memory to be erased and press ENTER The display will show a number to be confirmed Press ENTER to continue Press ESC to quit Copyright Silca 2005 Operating manual English SDD The display will show Key erasing lin POSIEIOr X Want to go on NO gt YES Select YES NO and press ENTER No to return to the previous menu Yes to erase the key from the position in the memory Position X ESC to quit The display will show DALES
4. Select YES NO and press ENTER No to return to the IMMOBILIZER function menu Yes to memorize the data relating to the operation completed Select ESC to quit Copyright Silca 2005 Operating manual English SDD The display will show DO you Want to Save PIN CODE Select YES NO and press ENTER No the data are archived except for the PIN CODE Yes the user data are archived USER DATA ARCHIVE To enter the user data the display will show USER DATA POS 001 DATE 19 07 01 SURNAME XXXXXXXXXX NAME XXXXXXXXXX REGNOS Ooo 10645 AD SURNAME required 12 characters NAME NUMBER PLATE optional 12 characters The following data will be saved automatically POS Location where the data will be saved DATE Operation date MAKE Make of the vehicle for which the operation was performed MODEL Model of the vehicle for which the operation was performed YEAR Model year Keys Mem Number of keys stored in memory PIN CODE if storage is confirmed by an operator IMMO ID Immobilizer control unit ID To enter the data use the T keys to position on the desired item press gt to enter and select the field where the text is to be typed Press ENTER to confirmed To quit and memorize the data press ESC Is the information inserted Correct NO gt YES Select YES NO and press ENTER No to return to the data entry window Yes to s
5. i 16 6 4 3 CAR MODEL ENABLED conan 16 6 4 4 COMMUNICATION PROCEDURE WITH THE IMMOBILIZER 17 6 5 REMOTE CONTROLS RKEl i 17 6 6 SETUP 3 17 6 6 1 ENABLING Di 17 6 6 2 LANGUAGE 32 19 6 6 3 SERIAL NUMBER 33 ic nooo consonancia 19 6 6 4 CLOCK Bi a 19 6 6 5 VERSION 35 20 6 6 6 MEMORIZE PASSWORD 36 20 6 6 7 KEYS REFERENCES conan 20 67 ARA 20 0 71 SEARCH l a da 21 072 DATA PRINTOD Losing tb yaaa ese ka 22 6 7 3 ARCHIVE ERASE 22 e E NEE 22 6 8 1 KEYBOARD II 22 6 8 2 TEXT NEE 22 6 8 3 GRAPHICS 53 23 6 8 4 UPDATE SWITCH CAN SA 23 A 23 Copyright Silca 2005 3 SDD Operating Manual English 6 9 1 DIN 23 002 DEALE ee Ee 23 6 9 3 IMPORTER aaa aa aaaaaaaaaaa 24 GUI PMI S Te e ene TR eee 24 7 VAG FUNCTIONS MENU AUDI SEAT SKODA VOLKSVAGEN 25 7 1 VAG GROUP 25 7 2 PROGRAMMING NEW KEYS 27 7 3 NUMBER OF KEYS MEMORIZED 30 7 4 READING IMMO ID 31 5 TERRORS eee E ee 32 TO ERASE ERRORS a eo ol es 33 8 OPEL VAUXHALL FUNCTIONS MENU 34 8 1 OPEL VAUXHALL lai 34 8 2 PROGRAMMING KEYS ococcciocococococococonononononononononononnnnncnonanonorcncncnos 35 8 2 1 PROGRAMMING KEYS A 35 624 B EEN 35 8 2 1 2 ERASE SELECTED KEY coccccccciciciococococncncncnninnnonininininonss 38 8 2 1 3 ERASING CURRENT KEN 40 8 2 1 4 ERASING ALL KEYS 41 8 2 2 PROGRAMMING ks
6. POS Location where the data will be saved DATE Operation date MAKE Make of the vehicle for which the operation was performed MODEL Model of the vehicle for which the operation was performed YEAR Model year Keys Mem Number of keys stored in memory PIN CODE if storage is confirmed by an operator IMMO ID Immobilizer control unit ID To enter the data use the T keys to position on the desired item press gt to enter and select the field where the text is to be typed Press ENTER to confirm Select ESC to quit and save the customer data Is the information inserted Correct NO Select and press ENTER No to return to the data entry screen Yes to save the customer data entered in the archive Select ESC to quit NUMBER OF KEYS IN MEMORY This function is used to view the number of keys stored in the immobilizer memory After selection the display will show NUM OF KEYS IN MEM Turn ignition omn Press any key Turn the key to the ON position and press a key Copyright Silca 2005 61 SDD 9 2 1 3 ATTENTION 62 Operating Manual English The display will show Keys number in memory XX Press any key Press a key to continue The display will show Tl Lon Ore Press any key Turn the key to the OFF position and press a key Remove the key ERASE ALL KEYS This function is used to erase all the keys stored
7. 13 There is an internal anomaly in the body computer 84 Copyright Silca 2005 Operating manual English SDD Press any key to continue ERROR MESSAGE N 14 PROGGRAMME RKE Procedure failed Press any key The remote control to be programmed is not the right one or is broken or errors have occurred during programming Make sure the remote control is the right one and efficient then repeat programming Press any key to continue ERROR MESSAGE N 15 Error found XXXX Eliminate the error before programming keys and or remote Controls Press any key If errors are found in the immobilizer programming cannot take place Delete the errors using the DELETE ERRORS function then repeat programming Press any key to continue ERROR MESSAGE N 16 The Body computer main control unit is not properly programmed programming operations cannot be carried out Have the body computer properly programmed by an authorized dealer then proceed with programming Press any key to continue Copyright Silca 2005 85 SDD 11 86 Operating Manual English HELP MENU This function is enabled after the selection of car make and model The following help functions are available F1 Press the function key F1 to read information relating to the MAKE MODEL selected MAKE MODEL YEAR REFERENCE SILCA ORIGINAL TRANSPONDER MEMORIZATION P
8. ERASING ALL KEYS This function is used to erase all the keys stored in the immobilizer memory to continue enter the PIN CODE ERASE ALL KEYS from the PROGRAMM KEYS menu and press ENTER The display will show ERASE ALL KEYS All key will be erased Want to go on TEO gt NO Select and press ENTER No to return to the previous menu Yes to erase all the keys stored in the immobilizer memory Select ESC to quit Enter the PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number DATES INSERTION PIN CODE Select ESC to quit Press ENTER to continue There is already a key in the ON position on the ignition unit The display will show Turn the key in OFF position Press any key Copyright Silca 2005 Operating manual English SDD Turn the key to the OFF position and press a key Deletion of all the keys then takes place After a few seconds 10 40 the display will show All keys has been erased po Deletion terminated After a few seconds the display will show TUE 1001 LOM OR Press any key Turn the key to the ON position and press a key 8 3
9. 42 8 2 2 1 NEW KEY ADDING e 43 8 2 2 2 OLD KEY ADDING coococcccccococcononononocnonononononanananano nora 45 8 2 2 3 ERASING ALL KEYS 48 93 READ ERROR EH 49 8 ERASE ERRORS serma 50 8 5 IMMO ID READING 300 50 8 5 1 PROGRAMMING KEYS C 51 8 5 1 1 ADD AN 51 8 5 1 2 ERASE ALL KEYS 54 8 5 1 3 NUMBER OF KEYS IN MEMORY 55 9 FORD FUNCTIONS MENU a aananniiainaanannannasaanannannannannanaanannannanaanannannanaanann 56 Of FORD EUROPA ele 56 9 2 PROGRAMMING NEW KEYS 59 9 2 1 PROGRAMMING NEW KEYS A 1 L cccccscsssesesecececererereseeeneeen 59 9 2 1 1 ADDkK N AN 59 9 2 1 2 NUMBER OF KEYS IN MEMORY 61 9 2 1 3 ERASE ALL KEYS 62 9 2 2 PROGRAMMING NEW KEYS B MASTER KEY SYSTEM 64 9 2 2 1 PROG MASTER KEY cooccoccccoiioiccocnononcncncnnonononcnononononcnnss 64 9 2 2 2 NUMBER OF KEYS IN MEMORY 66 9 2 3 PROGRAMMING NEW KEYS C 3 KEY SYSTEM 66 9 2 3 1 PROGRAMMING KEYS 66 9 2 3 2 NUMBER OF KEYS IN MEMORY 69 9 2 4 PROGRAMMING NEW KEYS D MASTER KEY SYSTEM 69 9 2 4 1 PROG MASTER KEY 69 9 2 4 2 NUMBER OF KEYS IN MEMORY 70 9 2 5 PROGRAMING NEW KEYS E MASTER KEY SYSTEM 70 9 2 5 1 PROG MASTER KEY 71 9 2 5 2 NUMBER OF KEYS IN MEMORY 73 9 2 6 PROGRAMMING NEW KEYS EL 73 9 2 7 PROGR MASTER KEY IG 74 9 2 8 PROGRAMMING NEW KEYS mn 76 4 Copyright Silca 2005 Operating manual English SDD GE READ ERROR S sdl re ene ne ner R TI dd ER
10. ON BOARD PROGRAM A 1 Programming new keys without use of programmed keys Copyright Silca 2005 Operating manual English SDD F3 F4 Press the F3 function key the display will show the position of the connector Graphic Image Select ESC to quit Press the F4 function key the display will show a description of the position of the connector POSITIONS Remove the cover Situated at the side of the hand brake Select ESC to quit Copyright Silca 2005 87 SDD 12 ATTENTION ATTENTION 12 1 88 Operating Manual English MAINTENANCE for repairs or replacement of parts for maintenance the CE mark is guaranteed only if original spare parts provided by the manufacturer are used The machine does not require special maintenance do not open the machine for any reason whatsoever Before starting any type of maintenance checks or replacement of parts read the following instructions Do not carry out any maintenance operations with the machine turned on Always disconnect from the mains Follow the instructions in the manual Use original spare parts PROBABLE CAUSE DISPLAY A CHECK POWER SUPPLY CONFIGURATION DISPLAY IS BLANK WITH MACHINE ON B CHECK CONNECTION WIRING REPLACE DISPLAY AFTER SALES SERVICE REPLACE ELECTRONIC CONTROL BOARD AFTER SALES SERVICE KEYPAD A CHECK CONNECTION WIRING NOT RESPONDING TO CONTROLS REPLACE KEYP
11. Red key Red key system petrol MK Red key Red key system diesel petrol with procedure different from MKD MKB 2KD 2 key system diesel 3KD 3 keys 3 key system diesel not used much outside the UK market 19 2KD 2 key system models 1 900 cc Turbo diesel 2 3 2K 2 key system models 2 300 cc Petrol The most complex case which may take longer to programme is the one with a red key where although the year of manufacturer and fuel type are known e g Diesel there are two possible procedures MK MKD ONLY ONE OF WHICH WILL WORK In this case there is no choice but to try them both which may prolong memorization time if the right one is the second one tried For other cases which do not involve red key systems it is very important for the customer to provide the right information 2 3 KEYS SYSTEM DIESEL PETROL so that it can be identified without error In any case if the information is partial or wrong e g the customer cannot say whether a Diesel car has a 2 or 3 key system it will simply increase the time required for memorization as two procedures will have to be tried 2KD 3KD ONLY ONE OF WHICH WILL WORK FIESTA FIESTA Use the arrow keys to select the make then press ENTER Press ESC to quit Copyright Silca 2005 57 SDD ATTENTION Operating Manual English FUNCTIONS MENU This section is used to carry out the functions involved in particular to to memorize new keys in the immobilizer
12. The display will show the message Insert MASTER key and TURN ON in Dosi i Press any key Turn the key to position 1 first click on ignition block and press any key to continue After a few seconds the display will show Safety access procedure Elapsed time XX max 560 sec Copyright Silca 2005 69 SDD ATTENTION 9 2 4 2 9 2 5 70 Operating Manual English The device and central immobilizer unit now start to communicate which may take up to 560 seconds If communication and data exchange has been successful at the end of the operation the display will show Safety access obtained After a few seconds the display will show Turm 11 1011 OLT and fit the 3 keys one after the other turning them to the ON position The lst fitted will be the master key Press any key Programming of the keys in the car now starts fit the three keys to be programmed in sequence and turn to the ON position taking care to fit tte MASTER KEY first the one already in the ignition block Press any key to continue Check in sequence that the second and third keys programmed start the Cats DO NOT USE THE MASTER KEY FOR THIS TESTI Press any key KEY TESTING to check that the procedure has been carried out properly test ignition of the engine by using the second and third keys programmed If one or both the keys do not start the car repeat the operation Never use the master k
13. an error with the keys has occured Press any key KEY TESTING to check that the memorized keys work test by turning on the car engine If there are problems repeat the operation Press a key to continue ARCHIVING OPERATIONS USER DATA All the operations carried out can be stored in the machine memory The display will show Do you want to save the customer data NO STED 11143 Select YES NO and press ENTER No to return to the IMMOBILIZER functions menu screen Yes to memorize the data relating to the operation completed ESC to quit The display will show Do you want to save PIN CODE Select YES NO and press ENTER No the data are archived except for the PIN CODE Yes the user data are archived USER DATA ARCHIVE This section is used to enter the user data to be saved for the operation completed The display will show USER DATA POS 001 DATE 19 07 01 SURNAME XXXXXXXXXX NAME XXXXXXXXXX REGNO XXXXXXXXXX TLS AD SURNAME required 12 characters NAME NUMBER PLATE optional 12 characters Copyright Silca 2005 29 SDD 7 3 30 Operating Manual English The following data will be saved automatically POS Position in which the data will be saved DATA Date of the operation MAKE Car make for which the keys has been memorized MODEL Car for which the keys has been memorized YEAR of the model Keys mem N
14. even when all the original keys are missing add new keys in the immobilizer PROG NEW KEYS A to create a new MASTER key red key and two normal keys PROG NEW KEYS B D E erase the code of all keys from the immobilizer memory provided at least two being reprogrammed PROG NEW KEYS A C or reprogrammed three PROGR NEW KEYS B D E check how many keys are in the immobilizer memory erase any anomalies in the immobilizer memory the structure of the programming system for FORD is such that one or more keys cannot be erased individually from the vehicle OPERATIONAL NOTES ALWAYS USE THE 03 OBDII FORD CABLE USE THE SPECIFIC 06 CABLE FOR MODELS WITHOUT THE DIAGNOSTICS SOCKET Use the machine to programme erase keys from the immobilizer memory only when absolutely necessary the programming or deletion procedure may take up to 30 minutes if possible use the direct manual programming deletion procedure described in the HELP F2 menu TRYING TO START A CAR WITH A KEY NOT IN THE MEMORY In such cases the immobilizer system protection is activated and the vehicle cannot be started even with enabled keys in this situation the immobilizer warning light flashes rapidly To release the vehicle place an enabled key into the ignition block and take to the ON position until the immobilizer warning light goes out the procedure takes a few minutes The structure of the FORD functions menu is as follows There is alrea
15. in order to enable the make involved to communicate with the centralized immobilizer unit The current machine configuration is enabled for AUDI FORD Europe OPEL VAUXHALL SEAT SKODA VOLKSWAGEN specific enabling is required when updating the program using the special USERS AGREEMENT included in the software updating kit SOFTWARE UPDATING The machine can be updated by means of connection to the RS232 serial line on a personal computer POWER SUPPLY From the car through an OBD Il connector 3 From the car through the cigarette lighter plug From the mains through a universal feeder and special cable TECHNICAL DATA ALIMENTAZIONE 8 45 Volt typically 12Volt from the vehicle diagnostic inlet or cigarette lighter plug Universal feeder INPUT OUTPUT 90 264 Vac 15 Vdc Pow En DIMENSIONS Lenght 235 mm Width 150 mm Height 70 mm Weight 450 g Copyright Silca 2005 Operating manual English SDD 1 3 WORKING PARTS A Retroilluminated LCD graphic display B 23 key keypad numerical functions arrows ESC ENTER C Parallel Port 25 Poles use only for printer D Serial Port RS232 9 Poles use only for Serial cable E Interface connection 15 Poles for power supply and communication with vehicle F Standard OBD II cable complete with universal adapter switch G Cigarette lighter power cable H F
16. in the immobilizer memory To do this two keys must be memorized The procedure for deletion of the memorized keys requires programming of two keys so that the immobilizer can start the vehicle Select the item ERASE ALL KEYS from the PROG NEW KEYS menu and press ENTER The display will show ERASE ALL KEYS It 1S necessary to have 2 programmed key Want to go on YES gt NO Select YES NO and press ENTER No to return to the data entry screen Yes to store the data entered in the archive ESC to quit The display will show Tien Dena 101 Ons Press any key Insert the key turn to the ON position and press a key Copyright Silca 2005 Operating manual English SDD The display will show Safety access procedure Elapsed time XX max 800 sec A dialogue then begins between the device and the immobilizer central unit which may take up to 800 sec If communication and data transfer has taken place successfully at the end of the operation the display will show Safety access obtained The deletion of all keys will then begin After a few seconds the display will show All keys has been erased Please wait Key deletion terminated The programming of the 2 keys in the vehicle then takes place After a few seconds if programming of the 1st key has taken place successfully the display will show the message Keys number in memory Please wai
17. issued by the car manufacturer Select and press ENTER the display will show IMMO ID READING XX XXXXXXXX XXXX XXXX XXXX KEY NUMBER 50 Copyright Silca 2005 Operating manual English SDD 8 5 1 8 5 1 1 The immobilizer identification IMMO ID is shown KEY NUMBER mechanical key code info available only on some car models Press to continue IDENTIFIER VIN XXXXXXXXXXXXXXXX Press ESC to gilt The following data are shown on this screen VIN Vehicle Identification Number Press J ESC to quit PROGRAMMING KEYS C This function is used to add keys to the immobilizer or erase them To programme new keys the PIN CODE must be known To enable the function select PROG KEYS and press ENTER The display will show PROG KEYS C gt ADD KEYS ERASE ALL KEYS NUM OF MEMORIZED KEY ADD KEY This function is used to add a maximum total of five operating keys to the system Select ADD KEYS and press ENTER the display will show ADD KEYS If you don t have PIN CODE you don t codify any key The PIN CODE is required Secret number with 4 digits The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID a
18. place the cursor in the required field and press gt Enter the characters to be searched for Press ENTER to proceed the search SEARCH METHOD POS DATE Digit a number or the date and press ENTER the display will show the corresponding record use the key to view the previous record the gt key to view the next record MAKE MODEL SURNAME NUMBER PLATE Digit the initial or part of the text to be searched for and press ENTER the display will show the first record available in order of position POS use the key to view the previous record the gt key to view the next record If none of the search criteria are met or there are no data in the archive the display will show NO INFORMATION RECOVERED Press any key and repeat the search USER DATA User data that meet the criteria are shown as follows USER DATA 0 DATE zZ070572007 BRAND AUDI MODEL A4 YEAR 95 98 SURNAME ROSSI NAME MARIO dI DI REG NO TV9988776 KEYS PIN 4567 IMMO ID F1 Copyright Silca 2005 21 SDD 6 7 2 6 7 3 6 8 6 8 1 6 8 2 22 Operating Manual English Use the gt keys to view the user data in sequence depending on the search selected Press key F1 to view the IMMO ID DATA PRINTOUT At present this function is not active ARCHIVE ERASE This function is used to erase all user data in the archive Select ERASE ARCHIVE from the ARCH
19. to continue the display will show If the warning light on the console is blinking repeat the procedure because an error with the keys has occured Press any key KEY TESTING to check that the memorized keys work test by turning on the car engine If there are problems repeat the operation Press a key to continue ARCHIVING OPERATIONS USER DATA The flow chart is the same as that described on page 60 PROGR MASTER KEY G This function is used to create a new MASTER key Red Key When a new MASTER key is programmed all the previously programmed keys are automatically deleted 3 keys are programmed one of which is the master key To activate the function select PROG NEW KEYS and press ENTER The display will show The master key memorizing procedure requires the programming of 3 keys in the central immobilizer unit the first of which is the MASTER KEY PROG MASTER KEY G You need to have three keys for programming Do you want Een Ge on PAS NO Tl AS Select NO YES and press ENTER NO returns to the previous menu YES proceeds with programming ESC returns to the previous screen The display will show the message Vr LI on Press any key Turn the key to the ON position and press a key After a few seconds the display will show Copyright Silca 2005 Insert all the keys to be memorized one after the other turning each one to the ON position If
20. x NO Select and press ENTER No to return to the previous menu Yes to erase the key from the position in the memory Position X ESC to quit DATES INSERTION PIN CODE gt XXXX ELN gt XXXX AD The PIN CODE must be entered and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Select ESC to quit Press ENTER to continue There is already a key in the ON position on the ignition unit Copyright Silca 2005 Operating manual English SDD The display will show Turn the key TA OFF posrttor Press any key Turn the key to the OFF position and press a key Deletion of the key inserted then takes place After a few seconds the display will show ERASING CURRENT KEY IN X position After a few seconds the display will show Turn Gneo On Press any key Turn the key to the ON position and press a key At the end of the operation return to the PROGRAMM KEYS A 8 2 1 4 ERASING ALL KEYS This function is used to erase all the keys stored in the immobilizer memory to continue enter the PIN CODE ERASE ALL KEYS from the PROGRAMM KEYS menu and press ENTE
21. A KEL ERASE SELECTED KEY ERASING CURRENT KEY ERASE ALL KEYS tU AD 8 2 1 1 ADD A KEY This function is used to add a new key Copyright Silca 2005 35 SDD 36 Operating Manual English Select ADD A KEY and press ENTER the display will show ADD A KEYS PROGRAM SELECTED KEY LN X POSITION gt NO YES Select YES NO and press ENTER No to return to the previous menu Yes to store the new key in the memory position X Press ENTER to confirm Press ESC to quit The display will show DATES INSERLION PIN CODE ZA A Enter the PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Select ESC to quit Press ENTER to continue KEY PROGRAMMING There is already a key in the ON position on the ignition unit The display will show TUE Lone tom OIT and insert the key to cOd1 ES Press any key Turn the key to the OFF position and insert the key to be programmed Press a key The programming stage of the key then takes place on the vehicle After a few seconds the display will show Copyright Silca 2005 Operating manual English SDD THE BEX H
22. AD AFTER SALES SERVICE NO COMMUNICATION WITH THE A CHECK THAT THE RIGHT CAR MODEL HAS BEEN CENTRALIZED UNIT SELECTED B CHECK THE WIRING REPLACE SW ADAPTER The instructions above relating to the probable causes of the faults described should be considered indicative and not a complete list of the possible causes of malfunctions Contact the After Sales Service in the event of any other problems arising CHECKING WIRING If it is necessary to check the machine s internal wiring proceed as follows Disconnect the supply wire Detach any other wires connected to the machine Remove the 4 screws located on the back of the machine Remove the cover carefully paying attention to the wiring Check that all the connectors are properly in place Copyright Silca 2005 Operating manual English SDD 13 Fig 4 14 14 1 WASTE DISPOSAL EU regulations establish special arrangements for the disposal of waste WASTE DERIVING FROM THE MACHINE The machine produces no waste during its use MACHINE The machine is made of re usable materials Re cycling is recommended ecological practice PACKING The machine is consigned in a cardboard packing box which can be re used if undamaged When it is to be thrown away it is classified as solid urban waste and it should be placed in the special paper collecting bins To facilitate disposal of the waste generated by the machine during its operation and of the machi
23. AS BEEN STORED After a few seconds the display will show Cura Ioni Elon Om Press any key Turn the key to the ON position and press a key KEYS TESTING ATTENTION to check that the memorized key works test by turning on the car engine If there are problems repeat the operation ARCHIVING OPERATIONS USERS DATA At the end of the memorizing operations the following message will appear Do you want to save the customer data Select YES NO and press ENTER No to return to the IMMOBILIZER function menu Yes to memorize the data relating to the operation completed Select ESC to quit The display will show Do you want to save the customer data NO Select YES NO and press ENTER No the data are archived except for the PIN CODE Yes the user data are archived Copyright Silca 2005 37 SDD 8 2 1 2 38 Operating Manual English USER DATA ARCHIVE To enter the user data the display will show USER DATA POS 001 DATE 19 07 01 SURNAME XXXXXXXXXX NAME XXXXXXXXXX REGNOS XXXXXKXXXX 110645 AD SURNAME required 12 characters NAME NUMBER PLATE optional 12 characters The following data will be saved automatically POS Location where the data will be saved DATE Operation date MAKE Make of the vehicle for which the operation was performed MODEL Model of the vehicle for which the operation was performed YEAR Model year
24. ASE E 78 9 5 NUMBER OF KEYS IN MEMORY esse teeeeeeeeeeeeaaes 19 96 IMMO ID READING il 80 10 WARNING ERROR MESSAGES 22aaaaaaaaaaanaaaanan nnnnannnnnnnnnunnnnnnnnnnnnnnnnnnnnn 81 11 PEEPMENO ilaele dear 86 12 MAINTENANCE eege 88 12217 CHECKING Eege 88 13 WASTE DISPOSAL 2 00 lella 89 TA ASSISTANCE istics cera 89 T HOW TO REQUEST SERVICE niiina lire 89 Copyright Silca 2005 5 SDD Operating Manual English 6 Copyright Silca 2005 Operating manual English SDD Fig 1 GENERAL The device is designed to the principles of European CE Directives The materials used in its manufacture are not dangerous and their use complies with directives Its design features make the machine and all its components completely safe to use FURTHER RISKS There are no further risks arising from the use of the machine PROTECTION AND SAFETY PRECAUTIONS FOR THE OPERATOR The operations for which the machine has been designed are easily carried out at no risk to the operator SAFETY REGULATIONS To operate under conditions of maximum safety do not use the device without reading and understanding clearly the contents of this operating manual e Check the electrical wiring periodically if the wires are worn they should be repaired or replaced e Never work with wet greasy or oily hands e Disconnect the device from the mains when it is not in use or in order to carry out maintenance work e Never tug at the power supply wire
25. D is able to automatically recognize the various central units connected and therefore uses the right communication procedure Simply identify CAR MODEL YEAR OF MANUFACTURE OPEL VAUXHALL AGILA ASTRA ASTRA ASTRA CALIBRA COMBO Use the arrow keys to select the make then press ENTER Press ESC to quit FUNCTIONS MENU This section is used to carry out the functions involved in particular to programme new keys in the immobilizer also when all the original keys are missing erase from the memory the code for one or more missing keys check how many keys are in the memory view immobilizer identification IMMO ID V I N and mechanical code only on certain models erase any anomalies found in the immobilizer memory ATTENTION the structure of the programming system for OPEL VAUXHALL allows keys to be added or erased individually in the vehicle The structure of the OPEL functions menu is as follows OPEL VAUXHALL gt KEYS PROGRAMMING PRESENT ERRORS ERRORS RESET IMMO ID READING tl AS Select and press ENTER Depending on the model of vehicle that is chosen the different types of menu may appear PROGRAMMING KEYS type A type B and type C 8 2 PROGRAMMING KEYS 8 2 1 PROGRAMMING KEYS A This function is used to add keys to the immobilizer or erase them To activate the function select KEY PROGRAMM and press ENTER KEYS PROGRAM A gt ADD
26. E ADDRESS The stamp shown above is often found in the vehicle maintenance booklet Copyright Silca 2005 23 SDD 6 9 3 6 9 4 24 Operating Manual English IMPORTER This is the ID code for the country in which the 7 digit code is applied for different from country to country The code is included in the rubber stamp used by the dealer to validate work on the vehicle DEALER NAME ADDRESS Table of currently known Importer Codes COUNTRY IMPORTER CODE ITALY 264 ENGLAND 210 ISRAEL 730 USA 444 CANADA 999 SPAIN 572 PORTUGAL 261 RIUNION ISLAND 387 To activate the function select IMPORTER and press ENTER PIN 4 This is the 4 digit code to enter as PIN CODE on the SDD during the PROG NEW KEYS or No KEYS MEM stages It is calculated by the device when the other codes are known Code7 Dealer Code Importer Code and date of issue CALCULATION OF PIN 4 To calculate the PIN 4 proceed as follows Insert the day month and year of issue of CODE 7 To activate the function select DATE and press ENTER Insert the PIN 7 DEALER and Importer CODE To activate the function select the figure to insert and press ENTER an asterisk will confirm that the figure has been entered VAG CONVERTER PIN 7 3 DEALER IMPORTER PIN 4 DATE XX XX XXXX EXIT F1 TLE esc Y The pin 4 will appear automatically once all the data have been entered DATA PIN 7 DEALER I
27. INSERTION PIN CODE gt XXXX PIN gt XXXX AD Enter the PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Press ESC to quit the function Press ENTER to continue There is already a key in the ON position on the ignition unit The display will show Turn the key in OFF Posteo Press any key Turn the key to the OFF position Press a key The deletion of key No X then takes place After a few seconds the display will show Key erased On xX position Copyright Silca 2005 39 SDD ATTENTION 8 2 1 3 40 Operating Manual English After a few seconds the display will show Turn L1ognition on Press any key Turn the key to the ON position and press a key At the end of the operation return to the PROGRAMM KEYS A KEYS TEST to check that the key no longer works test by trying to turn on the car engine ERASING CURRENT KEY This function is used to erase a key inserted into the immobilizer unit to continue enter the PIN CODE Select ERASING CURRENT KEY and press ENTER the display will show ERASING CURRENT KEY Key erasing Lil POsttion
28. IVE menu the display will show ARCHIVE ERASE ARCHIVE RESET gt NO YES Select and press ENTER Select ESC to quit TEST 5 This section contains all the controls with which to carry out a rapid operational test on the machine Select TEST from the MAIN MENU The display will show KEYBOARD TEAL GRAPHICAL UPDATE SWITCH CAN lo AD KEYBOARD 51 This function is used to test the operation of all the keys on the device keypad Select KEYPAD from the TEST menu To carry out the test press all the keys on the device one after the other To quit press any key three times Test result TEST PASSED all the keys are working properly TEST FAILED not all the keys has been pressed possible causes One or more keys not working properly The same key has been pressed for three times in a row TEXT 52 This function is used to test the operation of the display in the Text mode Select TEXT from the TEST menu 0123456789abcdefghijk 0123456789abcdefghijk 0123456789abcdefghijk 0123456789abcdefghijk 012345678 9abcdefghijk 0123456789abcdefghijk 0123456789abcdefghijk 0123456789abcdefghijk Check that the characters on the display correspond Press a key to quit Copyright Silca 2005 Operating manual English SDD 6 8 3 6 8 4 6 9 6 9 1 6 9 2 GRAPHICS 53 This function is used to test operation of the display in the GRAPHICS mo
29. If communication and data transfer has taken place successfully at the end of the operation the display will show Safety access obtained The key programming stage will then begin on the vehicle After a few seconds the following message will appear KEYS CODING If the key programming stage is successful the following message will appear along with the new amount of keys that has been memorize Keys number in memory XX Please wait After a few seconds the following message will appear Dion LOREELON OLE Press any key Turn the key to the OFF position and press a key KEY TESTING ATTENTION to check that the memorized keys work test by turning on the car engine If there are problems repeat the operation OPERATION ARCHIVES USER DATA At the end of the programming operation the display will show Do you want to save customer data NO 60 Copyright Silca 2005 Operating manual English SDD 9 2 1 2 Select YES NO and press ENTER No to return to the screen showing IMMOBILIZER functions menu Yes to memorize the data for the operation just completed ESC to quit USER DATA ARCHIVE To enter user data the display will show USER DATA POS 001 DATE L9707707 SURNAME XXXXXXXXXX NAME POLLICI REG MOE XXXXXXXXXX 05 AD SURNAME required 12 characters NAME NUMBER PLATE optional 12 characters The following data will be saved automatically
30. MPORTER ADVANCED OPTIONS The function can also be used for inverse calculation E g If you have the correct data for The DATE of ISSUE of CODE 7 3 of the 4 CODES required the missing CODE can be found Just insert the 3 items of known data and the missing figure will appear automatically Copyright Silca 2005 Operating manual English SDD 7 1 VAG FUNCTIONS MENU AUDIT SEAT SKODA VOLKSVAGEN VAG GROUP The functions on these vehicles are Programme new keys max 8 keys in the memory Reading of the number of keys memorized Read IMMO ID Read the errors present Delete all errors To make use of this function use Switch Adapter CABLE OBDII 00 STANDARD CABLE VAG 01 OPTIONAL PIN CODE Comprising 4 alphanumeric characters On the label together with the mechanical code New key s If applied for to the dealer it will have 7 All keys to be enabled Max 8 ae SE SR the Copyright Silca 2005 25 Copyright Silca 2005 Operating manual English SDD ATTENTION 7 2 SELECTING THE CAR MAKE In this case SDD is able to automatically recognize the various central units connected and therefore uses the right communication procedure Simply identify CAR MODEL YEAR OF MANUFACTURE VOLKSWAGEN BORA CADDY CADDY GOLE GOLF GOLE CABRIO Use the arrow keys to select the make then press ENTER Press ESC to quit FUNCTIONS MENU This se
31. R The display will show ERASE ALL KEYS All key will be erased Want to go on YES gt NO Select and press ENTER No to return to the previous menu Yes to erase all the keys stored in the immobilizer memory Select ESC to quit Enter the PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE Copyright Silca 2005 41 SDD Operating Manual English If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number DA ES INSERTION PIN CODE gt XXXX PIN gt XXXX AD Select ESC to quit Press ENTER to continue There is already a key in the ON position on the ignition unit The display will show Turn the key in OFF posit ron Press any key Turn the key to the OFF position and press a key Deletion of all the keys then takes place After a few seconds 10 40 the display will show All keys has been erased Deletion terminated After a few seconds the display will show VIN eo dee on On Press any key Turn the key to the ON position and press a key 8 2 2 PROGRAMMING KEYS B This function is used to add keys to the immobilizer or erase them Is not possible to erase keys individually on the vehicle To activate t
32. READ ERRORS This function is used to check for any anomalies memorized in the immobilizer Select the item READ ERRORS and press ENTER the display will show Please wait present errors NO ERRORS If there are no anomalies in the memory the display will show ERROR READING NO ERROR DETECTED Press any key ERRORS FOUND If there are anomalies in the memory the display will show ERROR READING Detected XX errors Press any key Copyright Silca 2005 49 SDD Operating Manual English The display will show how many errors XX there are in the immobilizer memory Press any key to see ERR XXXXXXXXXXX 1 X Description Of the error ERR XXXXXXXXXXXX code for error found Press L 0D to scroll all the errors found in sequence Press ESC to return to the previous menu 8 4 ERASE ERRORS Select ERASE ERRORS and press ENTER the display will show ERASE ERRORS Erase actual errors gt NO YES 14 QI Select and press ENTER No to return to the previous menu Yes to erase the errors in the memory Select ESC to quit The display will show the message TERMINATED ERASING Press ESC to quit Select ESC to return to the main menu 8 5 IMMO ID READING This function is used to view immobilizer identification ID IMMO a code comprising alphanumerical characters essential for finding a missing PIN CODE in such cases the PIN CODE is
33. ROCEDURE MAX NUMBER OF KEYS THAT CAN BE MEMORIZED CONNECTOR TO USE ADAPTER TO USE CONNECTOR POSITION Example BRAND MAKE A2 95 96 CONNECTS 00 Pos Con F3 F4 KEY REF HU66ATO Orig Tr MEG CR RW2 ID 48 F2 F3 F4 Ion Ni KEY 8 Self P F2 Connect type of cable to use to connect with the immobilizer see ID label on the cable Pos Con position on the vehicle of the diagnostics socket to which the device can be connected press F3 F4 to access the information KEY REF Silca key to use for the car model selected Orig Tr type of transponder used on the original key RW2 ID ID code for transponder used by RW2 No KEY max number of keys that can be memorized on the vehicle when the maximum number of keys is reached a key must be erased from the memory in order to memorize a new one Self P description of the direct programming procedure NOTE correspondence of the original transponder to the Silca key to be used should be checked with the RW2 for the type of transponder The F2 F3 F4 help menus are now available see last bottom line F2 Direct programming is a memorization deletion method for new keys on the vehicle which does not require diagnostics The procedure is active on certain models only as its use depends on the policy of the car manufacturer Press the F2 function key the display will show the direct programming procedure BRAND MAKE
34. TRONIC CIRCUIT FLOW CHART MAIN PARTS graphic display keypad IS buffer battery GC control circuit board serial port RS232 9 poles parallel port 25 poles not in use interface inlet 15 poles C1 C2 C3A C3B Display connector Keypad connector Connector for future applications Copyright Silca 2005 SDD SDD 2 1 Fig 3 2 2 2 3 2 4 12 Operating Manual English TRANSPORT The machine and its components are easily transported by one person and its handling does not incur any hazards PACKING The packing ensures safe transport for the machine and protects all its parts Da TRANSPORT To avoid knocks damaging the machine we recommend using the original carrying case and packing every time it is transported UNPACKING To remove the machine from its packing 1 take care not to damage the box when opening as it can be used again transfers dispatch to the manufacturer for repairs or maintenance 2 check the contents of the packing case which comprise 1 carrying case 1 machine 1 universal feeder 1 feeder adapter 1 centralized unit connecting cable universal OBDII 00 connector 1 universal switch adapter 1 connecting cable for FORD centralized units OBDII 03 connector 1 serial cable 1 power supply cable with cigarette lighter plug 1 set of documents user s manual guarantee form and user s agreement 1 pro
35. Turn the key to the OFF position and press any key KEY TESTING ATTENTION To check that the memorized keys work carry out at least 2 tests to start the engine If the test is negative repeat the operation ARCHIVING OPERATION USER DATA the flow chart is the same as that described on page 60 68 Copyright Silca 2005 Operating manual English SDD 9 2 3 2 9 2 4 9 2 4 1 ATTENTION NUMBER OF KEYS IN MEMORY the flow chart is the same as that described on chap 9 2 1 2 pag 61 PROGRAMMING NEW KEYS D MASTER KEY SYSTEM This function is used to create a new MASTER key Red Key When a new MASTER key is programmed all the previously programmed keys are automatically erased 3 keys are programmed one of which is the master key To activate the function select PROG NEW KEYS and press ENTER The display will show PROG MASTER KEY D gt PROG4MASTER KEY No KEYS MEM PROG MASTER KEY This function is used to create a new MASTER key The master key memorizing procedure requires the programming of 3 keys in the central immobilizer unit the first of which is the MASTER KEY Select PROG MASTER KEY and press ENTER the display will show PROG MASTER KEY You need to have three keys for programming Do you want to go on LEO NO tl AS Select and press ENTER NO returns to the previous menu SI proceeds with programming ESC returns to the previous screen
36. ble for enabling the immobilizer function Copyright Silca 2005 17 SDD Operating Manual English select the item REMOTE CONTROLS to wiew the vehicle makes available for enabling the Remote control Select and press ENTER After selection the display will show J ENABLING FLAGS gt AUDI FORD NISSAN OPEL SEAT Select the make required to view the enabling levels available and those already enabled ENABLE FLAGS BRAND LEVEL1 LEVELZ ki gt LEVEL3 To enter the enabling password to be requested by means of the document provided with the software updating floppy disk password application FORM select the level of enabling and press ENTER Select ESC to quit NOTE the levels marked are already enabled ENTERING THE PASSWORD After selection of the enabling level the display will show ENABLE FLAGS CAR BRAND Insert the Password f r apbpilrtatton LEVEL X XXXXXX Enter the password made up of 6 numerical characters Press ENTER to continue ESC to quit WRONG PASSWORD If a wrong password has been entered a beep advises the user and the display shows PASSWORD ABILITATION GROUP CAR BRAND WRONG Repeat the operation ATTENTION after 3 attempts the device locks to release disconnect from the power supply then re Connect 18 Copyright Silca 2005 Operating manual English SDD CORRECT PASSWORD If the Password entered is corr
37. c If communication and data exchange has been successful the display will show Safety access obtained After a few seconds the display will show Safety access procedure Elapsed time XX max 1000 sec The device and central immobilizer unit now begin to communicate which may take up to 1000 sec If communication and data exchange has taken place properly the display will show safety access obtained The deletion of all keys will then begin After a few seconds the display will show All keys has been erased Please wait All the keys has been erased Programming of the 2 keys in the car now starts After a few seconds if the 1st key has been programmed successfully the display will show the message Copyright Silca 2005 67 SDD Operating Manual English Keys number in memory Please walt After a few seconds the display will show Follow the procedure Turn Lone LON OLLA Insert the second key Jara LOnttTOR ON within 10 sec Press any key Turn the 1st key to the OFF position fit the 2nd key and turn to the ON position all within 10 seconds Press any key to continue The programming of the 2nd key in the vehicle then takes place After a few seconds if the key has been programmed successfully the display will show the message Keys number in memory Please wait After a few seconds the display will show TUEN LONIGO OLE Press any key
38. ction allows the functions to be carried out in particular to programme new keys in the immobilizer also when all the original keys are missing erase the code for a missing key from the immobilizer memory check how many keys are stored in the immobilizer memory view the immobilizer ID ID IMMO erase any errors in the immobilizer memory the programming system for the VAG group is structured so that every time programming takes place all the keys that will be used on the given car must be memorized again It is therefore not possible to add erase a single key individually If the wrong PIN CODE is entered 3 times consecutively the immobilizer unit will block To release it leave the key in the ON position from 30 minutes to 24 hours according to the vehicle The following is the structure of the VAG function menu VOLKSWAGEN gt PROG NEW KEYS MEM KEYS NUMBER IMMO ID READING PRESENTI ERRORS ERRORS RESET dI AS Select and press ENTER PROGRAMMING NEW KEYS This function can be used to add keys to the immobilizer or erase them To activate the function select PROG NEW KEYS and press ENTER The display will show PROG NEW KEYS r If you don t have PIN CODE you don t codify any key The PIN CODE is required secret number with 4 digits The PIN CODE is located on the black plastic tag provided with the car key on purchase Copyright Silca 2005 27 SDD 28 Op
39. de Select GRAPHICS from the TEST menu and check that all the pixel on the display are illuminated Press a key to quit UPDATE SWITCH CAN 54 This funxtion is used for manual updating of the internal software for the CAN BUS SWITCH Select UPDATE CAN BUS SWITCH from the TEST menu The display will show Optimization in Drogress Updating of the CAN BUS switch starti now When updating is complete the SDD re starts automatically 7 4 PIN CONV This function is used to convert a 7 digit pin code issued by the dealer to a 4 digit pin code for use on Volkswagen Audi Seat and Skoda vehicles To activate the function select 7 4 PIN CONV and press ENTER VAG CONVERTER PIN 7 DEALER TMPORTER PIN 4 DATE XX XX XXXxX E F1 UGD esc Y Use the up down arrow keys to select then press ENTER press ESC to exit PIN 7 This is a 7 digit code issued by the dealer How to apply for the code Use the function READ IMMO ID in SDD to read the series number of the central unit Provide the authorized dealer with the following data a Central unit series number b Chassis number c Copyoflog book d ID documentfor applicant DEALER This is the ID code for the authorized dealer different from dealer to dealer who issues the 7 digit code The code is included in the rubber stamp used by the dealer to validate work on the vehicle DEALER NAM
40. dy a key in the ON position on the ignition unit The display will show Tarni CORE LOM OIL Press any key Turn the key to the OFF position the display will show gt PROG NEW KEYS gt PROG NEW KEYS PROG MASTER KEY PRESENT ERRORS No KEYS MEM No KEYS MEM ERRORS RESET IMMO ID READING IMMO ID READING PRESENT ERRORS PRESENT ERRORS ERRORS RESET ERRORS RESET 58 Y AD TY AI Select and press ENTER Copyright Silca 2005 Operating manual English SDD 9 2 PROGRAMMING NEW KEYS 9 2 1 PROGRAMMING NEW KEYS A I L This function is used to add keys to the immobilizer or erase them To enable the function select PROG NEW KEYS and press ENTER The display will show PROG NEW KEYS A 1 L gt ADE A REY NUM OF MEMORIZED KEY ERASE ALL KEYS 9 2 1 1 ADD KEY This function is used to add a new key Select ADD and press ENTER the display will show Turn TOnttion On A Turn the key to the ON position ESC to quit ENTER to continue After a few seconds the display will show Insert the new key LUE Ignttion on Press any key Insert the key to be programmed turn to the ON position and press a key The display will show Safety access procedure Elapsed time XX max 800 sec A dialogue then begins between the device and the immobilizer central unit which may take up to 800 sec Copyright Silca 2005 59 SDD Operating Manual English
41. eat programming Press any key to continue Procedure interrupted Keys memorized before procedure started are enabled Press any key All keys memorized before programming started are still enabled for operation Press any key to continue ERROR MESSAGE N 10 FEL 1 Acquisition falled Key already acquired Repeat procedure Press any key The key to be programmed has already been programmed repeat programming Press any key to continue Procedure interrupted Copyright Silca 2005 83 SDD Operating Manual English Keys memorized before procedure started are enabled Press any key All keys memorized before programming started are still enabled for operation Press any key to continue ERROR MESSAGE N 11 PROG NEW KEYS KEY 23 Acquisition failed Key DOL Present OL without transponder Repeat procedure Press any key The key to be programmed is without a transponder Replace with a new key with transponder and repeat programming Press any key to continue Procedure interrupted Keys memorized before procedure started are enabled Press any key All keys memorized before programming started are still enabled for operation Press any key to continue ERROR MESSAGE N 12 Key memorization failed EEPROM memory error Press any key There is an internal anomaly in the immobilizer Press any key to continue ERROR MESSAGE N
42. ect the display will show ABILITATION GROUP CAR BRAND ABLE TATED The device is now enabled for the level selected 6 6 2 LANGUAGE 32 This function is used to select the language for the device Select the item LANGUAGE from the Setup menu the display will show LANGUAGE ITALIANO DEUTSCH FRANCAIS ENGLISH ESPANOL GREEK 1145 AD Select the language and press ENTER 6 6 3 SERIAL NUMBER 33 This function is used to view the serial number of the machine Select the item SERIAL NUMBER from the Setup menu the display will show SDD SERIAL NUMBER XXXXXXXXXXXXX 6 6 4 CLOCK 34 This function is used to set the machine s internal clock Select the item CLOCK the Setup menu the display will show CALENDAR CLOCK TIME OOO DATE XX XX XXXX 1145 QI Select the time or date to be altered Press ESC to quit Select ENTER to continue Follow the instructions given by the device Copyright Silca 2005 19 SDD 6 6 5 6 6 6 6 6 7 6 7 20 Operating Manual English VERSION 35 This function is used to view the FIRMWARE SW DATABASE version on the device Select the item VERSION from the Setup menu Ver SW XXX XX XXX Ver DB XX sxx Release gt XXXXXXX Ver SW version of the internal program Ver DB version of the car makes models database Update database update level g
43. eeder set Connection Feeder Feeder connection Copyright Silca 2005 9 SDD Fig 2 1 4 10 Operating Manual English MAIN FEATURES KEYPAD The machine keypad allows the user to interact with it rapidly and easily At any given time only the keys involved in the cycle in progress are enabled d DdD R H L H arrow keys move the cursor to the left or right Y A ft 4 arrow keys move the cursor UP or DOWN ENTER key confirms data entered or selection made ESC key quits or returns to the previous screen status LIQUID CRYSTAL DISPLAY Retroilluminated LCD graphic display 128x64 pixel or 21x8 characters SYMBOLS The box shows the machine screen and relative displays as shown below MAIN MENU IMMOBILIZER REMOTE CONTROLS KREE DATABASE EEE 34 PIN CONV UGD ESC D 1 2 i 4 J 6 Methods for selecting a specific function Use the arrow 1 keys to the point where the cursor gt shows the item required then press ENTER Digit a number xx from the keypad to access the item required directly from the menu KEYBOARD TEXT GRAPHICAL I Z 3 4 UPDATE SWITCH CAN UGD ESC D e g to access the GRAPHICS TEST menu 53 either use the arrows to select first the TEST menu 5 press ENTER then the GRAPHICS menu 3 and press ENTER or digit 53 which corresponds to the GRAPHICS TEST 53 Copyright Silca 2005 Operating manual English ELECTRICAL ELEC
44. erating Manual English The tag gives the mechanical code and the PIN CODE protected by a black plastic film scrape off with a coin If the PIN CODE is lost apply to a VAGE dealer for another one press ESC to quit press ENTER to continue The display will show DATES INSERTION PIN CODE gt XXXX Keys number S PLN N Keys Enter the PIN CODE and press ENTER Enter the Number of keys to be stored in the memory and press ENTER Press ESC to quit Press ENTER to continue The display will show CONNECTING tof t FF F Wait a few seconds to communicate with the immobilizer If a wrong PIN has been entered or there are errors during communication the display will show error message No 1 see chap 10 WARNING ERROR MESSAGES MEMORIZING KEYS lf communication has been successful the display will show COMMUNICATION OK Sequentially insert the keys and turn each one to the ON position Press any key Memorization of the keys in the car will now begin Insert all the keys to be memorized one after the other turning each one to the ON position If errors occur during programming the immobilizer warning light located on the dashboard will flash rapidly Repeat the operation Press a key to continue the display will show Copyright Silca 2005 Operating manual English SDD ATTENTION If the warning light on the console is blinking repeat the procedure because
45. errors occur during programming the immobilizer warning light located on the Operating manual English SDD ATTENTION Safety access procedure Elapsed time XX max 600 sec A The device and central immobilizer unit now start to communicate which may take up to 600 seconds lf communication and data exchange has been successful at the end of the operation the display will show Safety access obtained After a few seconds the display will show VAN OA EE and fit the 3 keys one after the other turning them to the ON POSICION The lst fitted will be the master key Press any key Programming of the keys in the car now starts fit the three keys to be programmed in sequence and turn to the ON position taking care to fit the MASTER KEY first the one already in the ignition block Press any key to continue Check in sequence that the second and third keys programmed start the car DO NOT USE THE MASTER KEY FOR THIS TEST Press a key KEY TESTING to check that the procedure has been carried out properly test ignition of the engine by using the second and third keys programmed If one or both the keys do not start the car repeat the operation Never use the master key to start the car Press any key to memorize the user data ARCHIVING OPERATION USER DATA the flow chart is the same as that described on page 60 Copyright Silca 2005 75 SDD 9 2 8 ATTENTION 76 O
46. ess any key to continue The display will show Turn the ignition OFF Press any key Turn the key to the OFF position and press a key Remove the key 9 6 IMMO ID READING This function is used to view the immobilizer identification Serial number Select and press ENTER the display will show IMMO ID READING XXXXXXXXX IMMO XXXXXXX XXXXXXX XX Press ESC to quit Select ESC to quit 80 Copyright Silca 2005 Operating manual English SDD 10 WARNING ERROR MESSAGES ERROR MESSAGE 1 COMMUNICATION ERROR ECU disconnected Preso FoC CO GULL ERROR MESSAGE 2 Communication error Press any key These error messages may appear during communication with the immobilizer if the connection is cut off or in the case of physical disconnection between the device and immobilizer disconnect the device from the socket and repeat the operation ERROR MESSAGE 3 Not recognized Orotocoal Press any key This message appears when a car model is selected but none of the queries from the different protocols used receive a coherent reply from the immobilizer Check that you have selected the right makemodel ERROR MESSAGE 4 NOT VALID PIN This message appears when the PIN CODE entered is not properly composed or is not recognized by the immobilizer Copyright Silca 2005 81 SDD Operating Manual English ERROR MESSAGE 5 Key not programmed Repeat procedure Press an
47. ey to start the car Press any key to memorize the user data ARCHIVING OPERATION USER DATA the flow chart is the same as that described on page 60 NUMBER OF KEYS IN MEMORY the flow chart is the same as that described on chap 9 2 1 2 pag 61 PROGRAMING NEW KEYS E MASTER KEY SYSTEM This function is used to create a new MASTER key Red Key When a new MASTER KEY is programmed all previously programmed keys are automatically erased 3 keys are programmed one of which is the master key Copyright Silca 2005 Operating manual English SDD 9 2 5 1 ATTENTION Select PROG NEW KEY and press ENTER The display will show PROG NEW KEYS E gt PROG MASTER KEY No KEYS MEM PROG MASTER KEY This function is used to create a new MASTER key The master key memorizing procedure requires programming of 3 keys in the central unit the first one of which is the MASTER KEY Select PROG MASTER KEY and press ENTER the display will show PROG MASTER KEY You need to have three keys for programming Do you want to go on gt YES NO 14 oa Select and press ENTER NO returns to the previous menu SI proceeds with programming ESC returns to the previous screen The display will show the message Insert MASTER key and TURN ON in POsit Lon L Press any key Turn the key to position 1 first click on the ignition block and press any key to continue Af
48. g for the program and database The words S N XXXXXXXXXXXXX give the machine serial number Check that the serial number shown on the display is the same as that on the document USER S AGREEMENT and on the label attached to the back of the machine Press F1 to continue PASSWORD When selection has been made the following message appears INSERT PASSWORD XXXXXXXX To use the machine enter the password issued by the supplier dealer comprising 8 numerical characters enter the password and press ENTER CORRECT PASSWORD If the password is correct the message below appears RIGHT PASSWORD After a few seconds the program enters the main menu Copyright Silca 2005 Operating manual English SDD WRONG PASSWORD If a wrong password has been entered a beep advises the user and the display shows WRONG PASSWORD INSERT PASSWORD XXXXXXXX Repeat the operation and press ENTER 6 2 1 PASSWORD MEMORIZED If the password has already been memorized on the machine cap 6 6 6 pag 20 when F1 is selected the following message appears PASSWORD SAVED Wait a few seconds for the display to show the main menu 6 3 MAIN MENU There are two ways to choose the menu MAIN MENU IMMOBILIZER REMOTE CONTROLS pond UP DATA BASE FEST Jae EEN CONV 1045 3 d Z 6 4 3 6 Use the IL arrow keys for selection then press ENTER or digit the number corresponding t
49. gram floppy disk 1 mains power cable HANDLING Always replace the machine in its carrying case after use Copyright Silca 2005 Operating manual English SDD 4 1 4 2 4 3 4 4 ATTENTION ACCESSORIES PROVIDED The device comes complete with universal feeder feeder adapter centralized unit connection cable OBD Il 00 connector complete with universal switch adapter FORD connection cable FORD OBDII 03 serial cable power supply cable with cigarette lighter plug documentation user s manual guarantee form and USER S AGREEMENT program floppy disk to be used in the event of loss of the program on the machine INSTALLATION AND PREPARATION Installation can be carried out by the purchaser and does not require special skills The machine is supplied ready for use however some checks and preparation are necessary before use PREPARATION FOR USE INITIAL OPERATIONS power the machine by means of the interface input 15 Poles E check that the serial number stamped on the device is the same as the one shown on the display enter the password to enable use see chap 6 2 PASSWORD select the language enter enabling for the car make if applicable see chap 6 6 1 ENABLING 31 CHECKING FOR DAMAGE The device will not normally damage if transport unpacking and installation have all been carried out according to the instructions in this manual however i
50. he function select PROGRAMM KEYS and press ENTER KEYS PROGRAM B gt NEW KEY ADDING OLD KEY ADDING ERASE ALL KEYS 42 Copyright Silca 2005 Operating manual English SDD 8 2 2 1 NEW KEY ADDING This function is used to add a key that has never been programmed in the immobilizer Select NEW KEY ADDING and press ENTER the display will show _ NEW KEY ADDING KEY STORING Select YES NO and press ENTER No to return to the previous menu Yes to programme the new key The display will show LAL One OLE Press any key Turn the key to the OFF position the display will show DATES INSERTION PIN CODE gt XXXX Enter PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Press ESC to quit Press ENTER to continue PROGRAMMING THE KEY The display will show INSERT THE NEW KEY TURN IGNITION ON Please walt Copyright Silca 2005 43 SDD Operating Manual English Enter the new key to be programmed and turn it to the ON position after a few seconds the display will show TOE TOnreLon OTT Press any key Turn the NEW key to the OFF posit
51. ilca 2005 65 SDD Operating Manual English KEY TEST ATTENTION to check that the procedure has been carried out properly check car ignition using the second and third keys programmed If one or both of the keys do not start the car repeat the operation Never use the Master key to start the car Press any key to memorize the User data ARCHIVING OPERATION USER DATA the flow chart is the same as that described on page 60 9 2 2 2 NUMBER OF KEYS IN MEMORY the flow chart is the same as that described on chap 9 2 1 2 pag 61 9 2 3 PROGRAMMING NEW KEYS C 3 KEY SYSTEM This function is used to add or erase keys in the immobilizer To activate the function select PROG NEW KEYS and press ENTER The display will show PROG NEW KEYS C gt PROG KEYS No KEYS MEM 9 2 3 1 PROGRAMMING KEYS This function is used to add two operating keys deleting all the previously memorized keys Select PROG KEYS and press ENTER the display will show You need to have two keys for programming ESC to quit ENTER to continue INSERT THE NEW KEY TURN IGNITION ON Press a key Enter the key to be programmed turn to the ON position and press any key 66 Copyright Silca 2005 Operating manual English SDD Nel display compare Safety access procedure Elapsed time XX max 800 sec The device and central immobilizer unit now begin to communicate which may take up to 800 se
52. inue Copyright Silca 2005 SDD 55 SDD 56 Operating Manual English FORD FUNCTIONS MENU FORD EUROPA The functions on these vehicles are Programme new keys max 8 or 15 keys in the memory Read IMMO ID Read the errors present Delete all errors To make use of this function use Switch Adapter CABLE OBDII 03 STANDARD CABLE FORD 06 OPTIONAL PRG NEW KEYS A 1 L 1 key is required B D E G Master Key System 3 keys are required C 3 Keys System 2 keys are required F A number of keys is required H Master Key System 2 keys are required WHERE TO FIND THE PLUG DIAGNOSTICS Copyright Silca 2005 Operating manual English SDD SELECTING THE CAR MAKE In this case SDD is unable to automatically recognize the various central units connected To identify the type of communication procedure to launch identify CAR MODEL YEAR OF MANUFACTURE DIESEL PETROL FUELLED RED KEY SYSTEM the new car had one red and 2 black keys procedures MKD MKB MK 2 KEY SYSTEM the new key had 2 black keys procedures 2K 2KD 3 KEY SYSTEM the new car had 3 black keys procedure 3KD A characteristic of the list of FORD models is the column containing a legend IN SQUARE BRACKETS that identifies the communication procedure for those models which may require a different procedure pes Tess Tee MKB Red key Red key system petrol MKD
53. ion Press a key to continue The display will show Tuer Lenton hi Please wait Turn the NEW key to the ON position Programming of the key on the vehicle then starts After a few seconds the display will show The key has been stored Press any key Press a key The display will show Other key to stored Select YES NO then press ENTER No to store the user data in the archive Yes to programme a new key At the end of the operation the display will show Extract the programmed key Press any key Press a key to store the user data in the archive 44 Copyright Silca 2005 Operating manual English SDD ATTENTION 8 2 2 2 TESTING KEYS to check that the programmed keys work properly carry out an ignition test on the car If necessary repeat the operation OLD KEY ADDING This function is used to add a key that was previously erased in the immobilizer Select OLD KEY ADDING and press ENTER the display will show OLD KEY ADDING KEY STORING gt NO YES Select YES NO and press ENTER No to return to the previous menu Yes to programme the new key The display will show Harm TOATCTLION OTE Turn the key to the OFF position the display will show DATES INSERTION PIN CODE Enter PIN CODE and press ENTER The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the f
54. iven by the manufacturer s code MEMORIZE PASSWORD 36 This option can be used to bypass the password which is required every time the machine is turned on Select the item MEMORIZE PASSWORD from the Setup menu the display will show MEMORIZE PASSWORD Select and press ENTER Select ESC to quit KEYS REFERENCES This option can be used to view the Silca or llco keys references on HELP F1 menu Select the item KEYS REFERENCES from the Setup menu the display will show KEYS REFERENCES Select the reference to display gt SILCA LLCO Select and press ENTER Select ESC to quit ARCHIVE 4 This section contains all the controls for searching printing or deleting user data stored in the device memory Select ARCHIVE from the MAIN MENU and press ENTER the display will show DATA BASE 1 SEARCH 2 PRINT DATA 3 ARCHIVE RESET Copyright Silca 2005 Operating manual English SDD 6 7 1 SEARCH 41 This control is used to make a search for POS Position in which the operation carried out was saved DATE date on which the operation was memorized MAKE car make MODEL car model SURNAME customer s surname NUMBER PLATE car number plate Select SEARCH from the ARCHIVE menu the display will show SEARCH XX XXXXXXXX XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX DPI AD Use the 4 arrow keys to
55. make sure it does not come into contact with oil sharp edges or heat e Itis dangerous to use the device in areas at risk damp or wet e Always work in a well lighted area e Keep the work area clean and remove all tools before turning on the machine e All visitors children in particular must keep at a safe distance and not touch the machine or electrical wiring e Do not use the device for purposes different from those described in the Operating Manual POWER SUPPLY The machine is supplied with electricity at 12 Vdc provided by the vehicle battery or as an alternative can be powered from a 15 Vdc universal feeder supplied with the machine TURNS ON The machine turns on automatically when the connection OBD II or Optional is connected to the diagnostics socket or one of the feeder wires supplied with the machine is used IDENTIFICATION OF THE SDD DEVICE The device has an identification plate showing its serial number Fig 1 E SILCA SpA Via Podgora 20 Z l y 31029 VITTORIO VENETO TV ITALY 0 0438 9136 Telefax 0438 913800 Telex 410579 SILCA I manufacturer s address machine TYPE N MATRICOLA SERIAL No serial No working voltage absorbed CE mark current absorbed power year of working manufacture freauencv Copyright Silca 2005 7 SDD 1 1 1 2 Operating Manual English MACHINE DESCRIPTION The machine is used to easily programme keys with transponders i
56. n the centralized immobilizer units of a number of car models In particular it can memorize all the keys in the centralized immobilizer unit erase keys already in the memory read the immobilizer ID code IMMO ID if applicable read the mechanical code for the key if applicable add one or more keys read the number of keys in the memory if applicable read any errors anomalies in the centralized immobilizer unit erase zero any errors found provide help The machine is provided with a password to prevent unauthorized use Users have at their disposal a functions menu to meet all possible requirements during operation NOTE Once the machine is connected to the power mains it s automatically switched on To turn it off exit from function and unplug the machine from the mains MAIN CHARACTERISTICS OPERATIONS Add keys to the centralized immobilizer unit or erase them SPECIAL FUNCTIONS Storage in an archive of operations carried out user data archive Multilingual program Machine test Help operational help for type and position of connectors procedures keys types of transponder etc PASSWORD A main password is necessary to operate the machine required every time it is turned on The password is issued by the supplier dealer on receipt of the special USERS AGREEMENT For given car makes special enabling is necessary i e a password to be entered once only
57. nd car chassis number Press ESC to quit Press ENTER to continue The display will show DATES INSERTION PIN CODE gt XXXX Copyright Silca 2005 51 SDD ATTENTION ATTENTION 52 Operating Manual English Enter the PIN CODE and press ENTER Select ESC to quit Press ENTER to continue KEY PROGRAMMING The key programming stage will then begin on the vehicle If a wrong PIN has been entered or there are errors during communication the display will show error message see chap 10 WARNING ERROR MESSAGES If the PIN is correct the display will show Turn the ignition OFF insert the key Lo program Press any key Turn the key to the OFF position and insert the key to be programmed Press any key The key have been stored Other key to stored Press ENTER to memorize a new key see KEY PROGRAMMING a maximum of five keys can be programmed including those already operatinal Press ESC to go to archiving operation user data TESTING THE KEY to check that the memorized keys and remote controls work test that all the remote controls lock and unlock the car and that the memorized keys start the engine always leave an interval of 30 40 sec between ignitions If the test is negative repeat the operation ARCHIVING OPERATIONS USERS DATA At the end of the memorizing operations the following message will appear Do you want to save the customer data
58. ne itself at the end of its useful life refer to identification of the main types of waste by the relative European CER code CER code Electronic circuit boards 16 02 16 Batteries 16 06 05 Paper and cardboard packaging 15 01 01 Plastic packaging 15 01 02 DISPOSING OF THE BATTERY The battery Fig 4 must be disposed of according to current regulations ASSISTANCE Silca provides full assistance to purchasers of the machine To ensure complete safety for the operator any job not specified in this manual should be carried out by the manufacturer or in the special Service Centres recommended by Silca On the back cover of this manual there is a list of the Service Centres and relative addresses HOW TO REQUEST SERVICE The guarantee attached to the machine ensures free repairs or replacements of faulty parts within 12 months of purchase All other service calls must be arranged by the customer with Silca or with a Silca service centre Waste is any substance or object deriving from human activity or natural cycles thrown away or to be thrown away Copyright Silca 2005 89 SDD 90 Copyright Silca 2005 Operating Manual English
59. ntralized unit memory PRESENT ERRORS Detected XX errors Press any key Press any key to view a description of the error ERR XXXXXXXXXXX 1 XX Description Of the error ERR XXXXXXXXXXXX error code x Press TY to scroll all the errors found in the memory Press ESC to quit 32 Copyright Silca 2005 Operating manual English SDD 7 6 ERASE ERRORS After selection press ENTER the display will show ERRORS RESET Erase actual errors gt NO YES Select YES NO and press ENTER No to return to the previous menu Yes to erase the errors in the memory ESC to quit After a few seconds the display will show TERMINATED ERASING Press ESC CO QUIE Press ESC to quit Copyright Silca 2005 33 SDD Operating Manual English 8 OPEL VAUXHALL FUNCTIONS MENU 8 1 OPEL VAUXHALL The functions on these vehicles are 40 Programme new keys max 5 keys in the memory Read IMMO ID Read the errors present Delete all errors To make use of this function use Switch Adapter CABLE OBDII 00 STANDARD L ty Code LL LIO Engine Type No Key No Radio Type Code Serial No CD Changer Type Code Serial No Phone Telematic Type Serial No 4 digit numerical New key s Max 5 On the Car Pass label WHERE TO FIND THE PLUG DIAGNOSTICS 34 Copyright Silca 2005 Operating manual English SDD SELECTING THE CAR MAKE In this case SD
60. ny key Press a key to view a description of the error ERR XXXXXXXXXXX 1 X Description Of Che errors 4 1165 AD ERR XXXXXXXXXXXX error code Press 1 Y 5 to scroll all the errors found Select ESC to quit The display will show Turn LONE LOM OTE Press any key Turn the key to the OFF position and press a key 9 4 ERASE ERRORS Select NO YES then press ENTER the display will show ERRORS READING Erase the active errors gt NO YES 78 Copyright Silca 2005 Operating manual English SDD Select and press ENTER No to return to the previous menu Yes to erase the errors in the memory Select ESC to quit The display will show Turn ignition on Press any key Turn the key to the ON position and press a key After a few seconds the following message will appear TERMINATED ERASING Press ESC CO GULE Select ESC to quit The display will show Tarm VIn r On OLT Press any key Turn the key to the OFF position and press a key 9 5 NUMBER OF KEYS IN MEMORY This function is used to view the number of keys memorized in the immobilizer After selection the display will show NUM KEYS IN MEM Turn ignition on Press any key Turn the key to the ON position and press any key The display will show Keys number in memory XX Press any key Copyright Silca 2005 79 SDD Operating Manual English Pr
61. o be programmed into the ignition block and turn to the ON position Carry out all these operations within 10 seconds Press any key to continue If the two keys has been memorized the display will show Keys number in memory Press any key If the number of keys memorized is different repeat the procedure making sure that the transponders in the keys are the right ones and working properly Press any key to continue The display will show TUE CONE Tol OTE Press any key Turn the key to the OFF position and press any key KEY TESTING to check that the memorized keys work test by turning on the car engine If there are problems repeat the operation ARCHIVING OPERATIONS USER DATA the flow chart is the same as that described on page 60 READ ERRORS This function is used to check for anomalies in the immobilizer memory Select then press ENTER the display will show ERRORS READING EE eC Mae son Ont Press any key Turn the key to the ON position and press a key NO ERRORS If there are no anomalies in the memory after a few seconds the display will show Copyright Silca 2005 77 SDD Operating Manual English ERRORS READING NO ERROR DETECTED Press any key ERRORS FOUND If there are anomalies in the memory the display will show how many errors XX there are in the central unit ERRORS READING Detected XX errors Press a
62. o the function 6 4 IMMOBILIZER MENU This function contains the database of vehicle makes models years for which the device is enabled and can carry out the specific functions involved Select IMMOBILIZER from the MAIN MENU to view a list of car makes on the display IMMOBILIZER MENU AUDI SEAT SKODA gt VOLKSWAGEN OPEL FORD Copyright Silca 2005 15 SDD 6 4 1 6 4 2 6 4 3 16 Operating Manual English SELECTING THE CAR MAKE Use the arrow keys to select the make then press ENTER Press ESC to quit After selecting the make the display will show the list of car models VOLKSWAGEN BORA CADDY CADDY GOLF GOLF GOLF CABRIO FUNCTION F1 Press the F1 key to show information relating to the make model selected type and position of connectors procedures keys types of transponder etc see chap HELP MENU SELECTING THE CAR MAKE SDD is not always able to automatically recognize all the immobilizer central units and is therefore unable to automatically choose the communication procedure to launch It is therefore NECESSARY to select the right MAKE gt MODEL gt ANY OTHER CHARACTERISTICS Petrol Diesel red key system etc to which the specific communication procedure is associated CAR MODEL NOT ENABLE If a car model that is not enabled is selected a beep is heard and the display shows VOLKSWAGEN Device not abilitated for this model Insert
63. ollowing information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Press ESC to quit Press ENTER to continue PROGRAMMING A KEY The display will show INSERT THE NEW KEY TURN IGNITION ON Please walt Copyright Silca 2005 45 SDD Operating Manual English Enter the OLD key to be programmed and turn to the ON position the display will show TUE ignition OTE Please walt Turn the OLD key to the OFF position the display will show Turn TOATELON n Please walt Turn the OLD key to the ON position The key is then programmed in the vehicle After a few seconds the display will show The key has been stored Press any key Press a key The display will show Other key to stored Select YES NO then press ENTER No to store the user data in the archive Yes to store the OLD key in the memory again At the end of the operation the display will show Extract the programmed key Press any key Press a key to store the user data in the archive 46 Copyright Silca 2005 Operating manual English SDD ARCHIVING OPERATIONS USERS DATA At the end of the memorizing operations the following message will appear Do you want to save the customer data Select YES NO and press ENTER No to return to
64. password from men SETUP ABILITATION 21 A CAR MODEL ENABLED If a car model that is enabled has been selected the display shows Insert the key and turn on the console Press ESC to quit Press ENTER to continue Copyright Silca 2005 Operating manual English SDD 6 4 4 COMMUNICATION PROCEDURE WITH THE IMMOBILIZER The following message appears Please walt CONNECTING ss The communication procedure with the immobilizer starts if the car model selected is correct and the immobilizer is detected the Functions menu by make appears otherwise an error message is shown see chap 10 WARNING ERROR MESSAGES 6 5 REMOTE CONTROLS RKE The choices in the menu are MAIN MENU IMMOBILIZER REMOTE CONTROLS J SETUP DATA BASE TEST 1 4 PIN CONV Ep esc D al 2 3 4 5 6 To select use the up down arrow keys until the gt cursor is on the required optino then press the ENTER key 6 6 SETUP 3 This section contains the various setting menus for the machine Select Setup from the main menu and press ENTER ENABLE FLAGS LANGUAGE SERIAL NUMBER CALENDAR CLOCK RELEASE STORE PASSWORD PICS AD 7 KEYS REFERENCES Select and press ENTER 6 6 1 ENABLING 31 After selection the display will show ENABLE FLAGS gt 1 IMMOBILIZER 2 REMOTE CONTROLS TLE esc 2 select the item IMMOBILIZER to wiew the vehicle makes availa
65. perating Manual English PROGRAMMING NEW KEYS H This function is used to add or delete keys in the immobilizer To activate the function select PROG NEW KEYS and press ENTER The display will show the procedure to memorize the key provides for the programming of at least 2 keys in the centralized unit PROG MASTER KEY G You need to have two keys for Programming DO Vou Want TO Go son gt YES NO TIL AS SelectNO YES and press ENTER NO to return to the previous menu YES to proceed with programming ESC to return to the previous screen The display will show the message Turn 1OnItion On Press any key Turn the key to the ON position and press any key to continue After a few seconds the display will show Safety access procedure Elapsed time XX max 600 sec Communication then starts between the device and immobilizer centralized unit and may last up to 600 seconds If the communication and data exchange have taken place successfully the display will show Safety access obtained After a few seconds the display will show Follow the procedure DEN LO ne On SEE Insert the second key TUE Lona tom On within 10 sec Press a key Copyright Silca 2005 Operating manual English SDD ATTENTION 9 3 Programming the keys in the vehicle then takes place Turn the key in the ignition block to the OFF position and remove Fit the second key t
66. r both the keys do not start the car repeat the operation Never use the master key to start the car Press any key to memorize the user data ARCHIVING OPERATION USER DATA the flow chart is the same as that described on page 60 NUMBER OF KEYS IN MEMORY the flow chart is the same as that described on chap 9 2 1 2 pag 61 PROGRAMMING NEW KEYS F This function is used to add or delete keys in the immobilizer To activate the function select PROG NEW KEYS and press ENTER The display will show PROG NEW KEYS F Keys number Y N keys Y Enter the number of keys to be programmed and press ENTER Press ESC to quit Press ENTER to continue The display will show Safety access procedure Elapsed time XX max 800 sec The device and central immobilizer unit now start to communicate which may take up to 800 seconds If communication and data exchange has been successful at the end of the operation the display will show Safety access obtained The key programming stage will then begin on the vehicle After a few seconds the following message will appear COMMUNICATION OK Sequentially insert the keys and turn each one to the ON position Press any key Memorization of the keys in the car will now begin Copyright Silca 2005 73 SDD ATTENTION 9 2 7 ATTENTION 74 Operating Manual English dashboard will flash rapidly Repeat the operation Press a key
67. s programmed is the MASTER KEY Select PROG MASTER KEY and press ENTER the display will show PROG MASTER KEY You need to have three keys for programming DO You Want TO GG On gt LES NO Tl AS 64 Copyright Silca 2005 Operating manual English SDD Select and press ENTER NO returns to the previous menu SI proceeds with programming ESC returns to the previous screen The display will show Turn ignition on Press any key Turn the key to the ON position and press a key to continue After a few seconds the display will show Safety access procedure Elapsed time XX max 560 sec The device and central immobilizer unit then begins a dialogue that could last up to 560 seconds If communication and data exchange has been successful the display will show Security access obtained After a few seconds the display will show T rn ignition Ofr and fit the 3 keys ne after the other turning them to the ON POSITION The lst fitted will be the master key Press any key The key programming stage on the car begins at this point Fit the 3 keys to be programmed one after the other and turn to the ON position making sure to fit first the key that will become the MASTER KEY Press a key to continue Check in sequence that the second and third keys programmed start the Cati DO NOT USE THE MASTER KEY BOR THIS TEST Press a key Copyright S
68. t After a few seconds the display will show Follow the procedure Turn LON eet volt Insert the second key Tarn 1001 100 ON within 10 sec Press any key Turn the 1st key to the OFF position insert the 2nd key and turn to the ON position do not take more than 10 seconds Press a key to continue Copyright Silca 2005 63 SDD Operating Manual English The programming of the 2nd key in the vehicle then takes place After a few seconds if programming takes place successfully the display will show the message Keys number in memory Please walt After a few seconds the display will show Eura OA LE LO Olas Press any key Turn the key to the OFF position and press a key OPERATION ARCHIVES USER DATA the flow chart is the same as that described on pag 60 9 2 2 PROGRAMMING NEW KEYS B MASTER KEY SYSTEM This function is used to create a new MASTER key Red Key When a new MASTER KEY is programmed all the previously programmed keys are automatically erased and 3 keys are programmed one of which is the master key To activate the function select PROG NEW KEYS and press ENTER The display will show PROG NEW KEYS B gt PROG MASTER KEY No KEYS MEM 9 2 2 1 PROG MASTER KEY This function is used to create a new MASTER key ATTENTION The memorization procedure for the master key requires the programming of 3 keys in the central unit The first of the 3 key
69. t is always advisable to check that the machine has not suffered any damage Should faulty operation arise that is not connected with the above mentioned conditions please contact After Sales Service ENVIRONMENTAL CONDITIONS To ensure that the best use is made of the machine and that the keys with transponders produced work properly it is important to bear in mind operating conditions and temperature Given the characteristics of the transponders on the keys in order to memorize them THE TEMPERATURE MUST BE ABOVE 5 C Ideal working conditions for the machine are therefore temperature from 5 to 40 C SOFTWARE UPDATING The machine software can be updated by connection to a personal computer the RS232 socket for connection to the PC is located on the front 4 page 11 near the display Use the RS232 serial cable provided and follow the instructions for updating REGULATION AND GAUGING The machine is designed not to require any gauging or regulation Copyright Silca 2005 13 SDD 6 1 6 2 14 Operating Manual English USING THE MACHINE This chapter describes all the operations required to memorize erase or add keys to the centralized immobilizer unit START UP When the machine is turned on the display shows the logo After a few seconds the following message appears Update XXXXXXX S N XXXXXXXXXXXXX F1 to continue The words Update XXXXXXX give the level of updatin
70. ter a few seconds the display will show Safety access procedure Elapsed time Xx J max 2560 Ses The device and central immobilizer unit now start to communicate which may take up to 560 seconds If communication and data exchange has been successful at the end of the operation the display will show Copyright Silca 2005 71 SDD Operating Manual English Safety access obtained After a few seconds the display will show Pie Leonie Lom On Press any key Turn the key to the ON position Il and press any key safety access procedure Elapsed time XX max 1000 sec The device and central immobilizer unit now start to communicate which may take up to 1000 seconds If communication and data exchange has been successful at the end of the operation the display will show Safety access obtained After a few seconds the display will show Start the car with all 3 keys START WITH MASTER KEY Press any key Programming of the keys in the car now starts fit the three keys to be programmed in sequence and turn on the engine taking care to fit the MASTER KEY first the one already in the ignition block Press any key to continue 72 Copyright Silca 2005 Operating manual English SDD ATTENTION 9 2 5 2 9 2 6 KEY TESTING to check that the procedure has been carried out properly test ignition of the engine by using the second and third keys programmed If one o
71. the IMMOBILIZER function menu Yes to memorize the data relating to the operation completed Select ESC to quit The display will show Do tt want to save PIN CODE Select YES NO and press ENTER No the data are archived except for the PIN CODE Yes the user data are archived USER DATA ARCHIVE To enter the user data the display will show USER DATA POS 001 DATE 19 07 01 SURNAME XXXXXXXXXX NAME XXXXXXXXXX REG NO OOOO 110645 AD SURNAME required 12 characters NAME NUMBER PLATE optional 12 characters The following data will be saved automatically POS Location where the data will be saved DATE Operation date MAKE Make of the vehicle for which the operation was performed MODEL Model of the vehicle for which the operation was performed YEAR Model year Keys Mem Number of keys stored in memory PIN CODE if storage is confirmed by an operator IMMO ID Immobilizer control unit ID To enter the data use the T keys to position on the desired item Press gt to enter and select the field where the text is to be typed Press ENTER to confirmed To quit and memorize the data press ESC Copyright Silca 2005 47 SDD 8 2 2 3 48 Operating Manual English Is the information I Sette CCrrect NO gt YES dI 2 Select YES NO and press ENTER No to return to the data entry window Yes to store the data in the file
72. tore the data in the file Copyright Silca 2005 53 SDD 8 5 1 2 54 Operating Manual English ERASE ALL KEYS This function is used to erase all the keys stored in the immobilizer memory to continue enter the PIN CODE The PIN CODE is located on a card similar to a credit card handed to the customer on purchasing a car The card gives the following information Mechanical Code Car radio Code Secret Code PIN CODE If the PIN CODE is lost apply to an authorized OPEL dealer for another one providing the IMMO ID and car chassis number Select ERASE ALL KEYS and press ENTER The display will show ERASE ALL KEYS All key will be erased Select and press ENTER No to return to the previous menu Yes to erase all the keys stored in the immobilizer memory Select ESC to quit DATES INSERTION PIN CODE gt XXXX Enter the PIN CODE and press ENTER Select ESC to quit Press ENTER to continue All keys has been erased Press any key Press a key to continue Turn the ignition OFF Press any key Turn the key to the OFF position and press a key Copyright Silca 2005 Operating manual English 8 5 1 3 NUMBER OF KEYS IN MEMORY This function is used to view the number of keys memorized in the immobilizer After selection the display will show NUM OF KEYS IN MEM Keys number in memory XX Press any key Press a key to cont
73. umber of keys memorized PIN CODE if memorization is confirmed by the operator IMMO ID Immobilizer identification To enter the data use the keys to position the cursor on the item required press gt to enter and select the field in which to digit the text NOTE to select the letter required press the corresponding key N times The programming capacity of the archive is approx around 100 users data Glossary e e Press ENTER to confirm To quit and memorize the data press ESC Select YES NO and press ENTER CET ER ER WER 5 JKL5 6 CS ER CS o Is the information Inserted COLG CE NO gt YES No to return to the data entry screen Yes to store the data in the archive NUMBER OF KEYS MEMORIZED This function is used to view the number of keys memorized in the immobilizer After selection the display will show MEM KEYS NUMBER If you don t have PIN CODE you dont codify any key The PIN CODE is required to use this function Copyright Silca 2005 Operating manual English SDD press ESC to quit press ENTER to continue The display will show DATES INSERTION PIN CODE gt XXXX PIN XXXX Po Enter the PIN CODE press ESC to quit press ENTER to continue The display will show CONNECTING tof to RF FF At the end of the operation the display will show Keys number in memory Y Press any key
74. y key This message appears when key programming is not successful Repeat the procedure ERROR MESSAGE 6 REMOTE CONTROL not programmed Repeat procedure Press any key This message appears when remote control programming is not successful Repeat the procedure ERROR MESSAGE N 7 PROG NEW KEYS KEY 1 Acquisition failed Key faulty Repeat procedure Press any key The key to be programmed is faulty replace with a new key and repeat programming Press any key to continue Procedure interrupted Keys memorized before procedure started are enabled Press any key All the keys memorized before programming started are still enabled for operation Press any key to continue ERROR MESSAGE N 8 KEY i Acquisition failed Authentication failed Repeat procedure 82 Copyright Silca 2005 Operating manual English SDD na any key The key to be programmed is a wrong key replace with the right key and repeat programming Press any key to continue Procedure interrupted Keys memorized before procedure started are enabled Press any key All the keys memorized before programming started are still enabled for operation Press any key to continue ERROR MESSAGE N 9 KEY 1 Acquisition failed Disabled key Repeat procedure Press any key The key to be programmed has been erased and cannot be re programmed Replace with a new key and rep

Operating Manual

Contents

Download Pdf Manuals

Related Search

Related Contents