Home

43cm/17" TFT Rack Console (RC25)

1. O Cable management part fixing pin O Support bracket Used for installation in an asym PRIMERGY rack Rack mount parts O Cage nut M5 x4 O Centering screw M5 Torx T20 x2 Used for installation in an asym PRIMERGY rack O Security lock x4 O Unlocking tool x1 locuments Quick Start Guide This guide x1 CD ROM x1 User s Manual Quick Start Guide Warranty Sheet Safety Precautions and Other Important Information x 1 1 Remove the cable management part monitor cable keyboard and mouse cables two PS 2 cables or one USB cable AC power cable and six cable ties from the accessory box 2 Use cable ties to anchor the cables to point a on the cable management part and continue anchoring them to points b c d e and f e Monitor cable and keyboard and mouse cables have a white marking that indicates the point on the cable to be fixed at point a on Point the cable management part AC power cable connector bush a There is no marking on the AC power cable Align the end of the housing of the monitor a NS cable with the base of the AC power cable ft y bush and anchor them to point a This will E AI allow the cables to be installed without any slack when connected to the back of the i Monitor cable connector Rack Console Attach cables on the folded cable management part without any slack in the cables PS 2 cable MS PS 2 cable KB Monitor ca
2. Quick Start Guide fo FUJITSU 43cm 17 TFT Rack Console RC25 Thank you for purchasing the 17 inch Rack Console RC25 In this guide you can find precautions and information about unpacking this product checking and installing the items in the package and connecting the cables This guide contains important safety precautions that must be taken when you unpack install this product and connect the cables Carefully read and thoroughly understand this guide before performing operations The attached CD ROM User s Manual and Safety Precautions and Other Important Information also provide important information for using this product safely Carefully read these documents as well before using this product in order to ensure safe and correct use Keep these documents handy for reference at all times Conventions Symbols and terminology that are used in this guide are described below Point Double quotations This symbol indicates the possibility of physical damage such as damage to this product or physical injury which may result through improper operation This symbol indicates supplemental comments or hints information Double quotation marks are used to indicate the title of a chapter or document to be referenced or important terms Sequential numbers preceding text indicate the order of Sequential numbers operations described by the text Circled numbers in a figure indicate the order o
3. ack Mount Kit See above for the installation procedure i gt ed Left rear side rack brace ao asymmetrical PRIMERGY rack bS we G ay Centering screws M5 Torx T20 7 S Front side rack brace Insert the unlocking tool into the opening in the Easy mounting clip disengage the lock and then remove the RC25 Rack Mount Kit from the front side rack brace 1 Pull out the intermediate members of the slide rails until the members are locked 2 Pull out the retainers to the front ends of the rails 3 Insert the Rack Console into the slide rails Push the Rack Console until it locks on the slide rails Retainer 1 Secure the rear bracket of the cable management part with the finger screw on the rear protrusions of the RC25 Rack Mount Kit on the left rear side rack brace iors Rear bracket fy In 2 Fix the front bracket to the fitting on the rear of the Rack Console 3 Insert the pin for fixing the cable management part into the hole Firmly push the pin until the ball lock is securely in place Pin for fixing the cable management Ring for removing part the pin CAUTION If the ring for removing the pin SSS rests on the Rack Console or RC25 Rack Mount Kit after the pin has S been inserted it might not be possible to store the Rack Console Therefore be sure that the ring rests on the center of the unit as shown in this figur
4. ble or USB cable as the cable to CAUTION connect the keyboard and mouse If both cables are connected and any operational problem occurs on the keyboard or mouse the server must be rebooted Opening and Closing the Monitor To open the monitor 1 Grip the monitor handle and open the monitor upward To close the monitor 1 Make sure that nothing is connected to the Virtual Media USB port on the front side of the device 2 Hold the handle and slowly close the monitor downward Handle II L EEANN When you open the monitor upward if you cannot open it with one CAUTION hand or you feel it is too heavy to open with one hand open it with both hands When closing the monitor make sure there is nothing connected to the front Virtual Media USB port and be careful to not pinch your fingers between the monitor and the keyboard 1 Push the fixing springs on the ends of the right and left slide rails and slide the device back into the rack slowly 2 Tighten the finger screws on the right and left front ends of the device Finger screw screws Be careful not to pinch your hands or fingers in the slide rails or CAUTION Rack Console itself when you stow the Rack Console NC14010 L593 02
5. ble wer AC power cable e Arrange the cables as shown in the figures AC power cable on bottom with the monitor cable on top and the ee and mouse cables to the side The figures show the cables anchored at point a Monitor cable PS 2 Keyboard cable Monitor cable USB cable PS 2 Mouse cable AC power cable AC power cable tie cable NX cable tie When using PS 2 cables for the keyboard and mouse When using a USB cable for the keyboard and mouse Attach cables on the folded cable management part and arrange them as indicated without any slack in the cables between fixing points Slack cables may dangle unnecessarily when the device is installed Removing the RC25 Rack Mount Kits 1 Loosen the finger screws on the right and left front ends and then remove the slide fixing brackets T Remove the RC25 Rack Mount Kits Bs Push the fixing springs to unlock the RC25 Rack Mount Kits Mount Kits and then pull them out backwards SS Unlock the intermediate member locks of the slide rails and store the intermediate members in the outer members Point RC25 Rack Z Oter member AS member Slide fixing bracket for transport 4 Remove the spring locks on the rear Finger screw side of the RC25 Rack Mount Kits k Spring lock Keep the removed slide fixing brackets and spring locks in a safe place They may be required if you move the device to another location Point Installing the RC25 Rack Mou
6. e Connecting Cables 1 Turn off all devices that are connected to the RC25 except for hot plug connections 2 Connect the PS 2 or USB cable and monitor cable to this device The Virtual Media Port USB is used to connect a Virtual Media KVM switch sold separately to this device For more information see the User s Manual for the KVM switch you are using 3 Plug the AC power cable connector into the power socket on this device By iP areas Connect the cables to the z TI monitor port keyboard port ol and mouse port on the server E or a KVM switch USB Ps 27 Plug the Rack Console s power AC power ae AT cable USB cable cable into the power outlet cable a KB PS 2 Make sure that all connections cable are completed before turning al EA on the power of the Rack MW 8 Console server KVM switch ey i and other devices vy Power outlet Monitor port Keyboard and mouse ports either USB or PS 2 Remark virtual media cable has to be ordered optionally Connector color is gray to distinguish from USB keyboard touch pad cable black connector Connect the following cables to this device as shown in this figure so there is no slack f AC power cable on bottom oint Monitor cable on top e If the cables are pulled too tightly after connecting the monitor cable to this device adjust the lengths of the cables Select either the PS 2 ca
7. f Circled numbers operations Unpacking 1 Open the package box and remove the top board This guide is located on top of the device 2 Remove the accessory box 3 Open the plastic bag and remove the Rack Console e Make sure to open the plastic bag before removing the device e Put your hands in the two square spaces A and B on the front and rear of the Rack Console Firmly support the bottom of the device while removing it from the package Top board Plastic bag A Rack Console 7 A Accessory X box i Quick Start Guide When you open the package check for damage to the product e When you remove the product from the package open the plastic bag that covers the device and directly hold the device to lift it Otherwise you may drop the device and it may cause personal injury or damage the device We recommend keeping the box and packing material in which the Rack Console was purchased They may be required if you move the device to another location If something is missing from the package contact your supplier or local Fujitsu representative engineer A26361 K1 a8 1 240 17 7619 Point Packing List Make sure that the items in the following list are included in the shipping package Rack Console ccessories Monitor cable 3m PS 2 Keyboard cable 3m PS 2 Mouse cable 3m USB cable 3m AC power cable 3m Cable tie o00000 gt a O Cable management part
8. nt Kits to the Rack 1 Attach one cage nut on each of the right and left front side rack braces and attach another cage nut on the left rear side rack brace 2 Insert the two protrusions on the rear side of the RC25 Rack Mount Kits into the rear side rack braces so that the inserted RC25 Rack Mount Kits are at the same height unit U One RC25 Rack Mount Kit is for the left rear side rack brace and the other is for the right Find the letters LEFT or RIGHT on the side of each RC25 Rack Mount Kit and attach each RC25 Rack Mount Kit to the suitable side of the rack Keep the RC25 Rack Mount Kits horizontal at the same height unit U and attach them to the front side rack braces Check that the Easy mounting clips and centering screws are inserted firmly into the front side rack braces Insert the Security locks into the left and right Easy mounting clips on the front side of the RGS Zack Mount Kits Cage nut Easy eper Security 4 rack braces l Cage nut f x Security p N 1 locks 9 pi Cage nut e i Front side rack braces n Rear side rack brace To install in an asymmetrical PRIMERGY rack To remove the RC25 Rack Mount Kit 1 Use two centering screws M5 Torx T20 to 1 Insert the unlocking tool between the Easy install the support bracket on the left rear side mounting clip and the Security lock as shown in rack brace the figure and then remove the Security lock 2 Install the RC25 R

43cm/17" TFT Rack Console (RC25)

Contents

Download Pdf Manuals

Related Search

Related Contents

43cm/17&quot; TFT Rack Console (RC25)

Contents

Download Pdf Manuals

Related Search

Related Contents

43cm/17" TFT Rack Console (RC25)