iConverter® NMM2
Contents
1. When a port is operating in Manual mode its Pause j operation mode is based on the Pause Disable Enable DIP switch setting Figure A DIP switch Location SW2 RESERVED NOTE DIP switches marked Reserved must be kept in the Left factory default position SW3 UTP AUTO MANUAL When this DIP switch is in the UTP Auto Negotiate AN position factory default the UTP port automatically determines the speed and duplex mode of the connecting UTP device DIP switches SW3 SW4 and SW5 determines the speed and duplex modes advertised by the module See Figure C on the following page for more information Switch Left Default Right OFF PAUS y Pause Disable Pause Enable SW2 RESERVED AN MAN W UTP Auto neg UTP Manual 100 10 SA UTP 100Mbps UTP 10Mbps FDX HDX o UTP Full duplex UTP Half duplex Swe A DS Disabled A EN Enabled Backplane Port A Backplane Port A Ta B EN Enabled W she rar poe a rplane P Port B SW8 RESERVED Figure B DIP switch Description SW4 UTP 10 100Mbps When the UTP AN MAN DIP switch is in the manual MAN position the 10 100 DIP switch determines the speed of operation for the UTP port SW5 UTP FULL HALF DUPLEX When the UTP AN MAN DIP switch is in the manual MAN position the UTP Full Half Duplex FDX HDX DIP switch determines the duplex operation mode of the UTP port SW3 SW4 SW5 Function The UTP2. 040 8000N 001A 3 09 Omnitron Systems Technology 140 Technology Dr 500 Irvine CA 92618 949 250 6510 tel 949 250 6514 fax www omnitron systems com osr Omnitron Systems Technology Inc iConverter NMM2 Network Management Module QUICK START GUIDE The Converter NMM2 provides real time management trap notification and remote configuration of iConverter equipment It supports SNMPv1 SNMPv2c SNMPv3 and Telnet protocols SMNPv3 provides secure access to devices by a combination of authenticating and encrypting packets over the network For more information including the complete User Manual on the NMM2 module access Omnitron s documentation download web page to view all relevant documents http www omnitron systems com downloads_iconverter php INSTALLATION PROCEDURE 1 Configure DIP Switches 2 Install Module in Chassis and Connect Cables 3 Configure Module via Command Line Interface 4 Verify Operation 1 CONFIGURE DIP SWITCHES DIP SWITCHES The location of the DIP switch is illustrated in Figure A and the description is shown in Figure B SW1 PAUSE When the UTP port is operating in Auto Negotiation its Pause operation mode is determined by the Pause capability advertised during AN between itself and the link partner The port advertises its Pause capability Symmetrical or No Pause during AN based on the Pause Disable Enable DIP switch setting Switch 1 Switch 8 LEFT
3. module does not have a password and will skip the Password Entry screen and go straight to the Management Options screen If a password has been set the Password Entry screen will be displayed Type the password and press lt ENTER gt the NMM2 will respond with the Management Options screen From the Management Option screen it recommended to configure e serial port password option 3 from the Management Options screen e telnet password option 3 from the Management Options screen e IP address of the module option 3 from the Management Options screen e SNMP parameters option 4 from the Management Options screen See the full version of the User Manual for more information
4. 4 VERIFY OPERATION Once the module has been installed and configured per steps 1 3 verify the module is operational by viewing the status of the LED indicators The table below provides a description for each indicator The Power LED indicates the module is receiving power from the chassis The NUM2 has an LED indicator for each available power supply in the chassis 19 Module Chassis has three 5 Module Chassis has two The Master Slave and Management LEDs indicate the operation and configuration of the management channel A blinking Mgt LED indicates the NMN2 is polling the chassis The UTP 10 or 100 LED indicates the module has established a connection across its UTP port A blinking LED indicates the presence of data LED Function 7 z Color OFF State ON Blinking State Legend ewer Green No Power Module has power Pwr Power Supply Status ON Power available PS Green Power Supply not installed Biking Supply installed but not powered Master Slave Green Slave Mode ON Chassis Master Msr Slv all Green Not polling chassis ON Polling chassis 10Mbps UTP ET 10Mbps not selected or ON Active 10Mbps UTP link 10 disconnected Blinking UTP data activity 100Mbps UTP Creen 100Mbps is not selected or ON Active 100Mbps UTP link 100 disconnected Blinking UTP data activity P H Green Half duplex Full duplex Figure D LED Indicators
5. port is set to Auto Negotiation AN 100 FDX with the following modes advertised 100F 100H 10F 10H The UTP port is set to Auto Negotiation AN 100 HDX with the following modes advertised 100H 10F 10H The UTP port is set to Auto Negotiation AN 10 FDX with the following modes advertised 10F 10H The UTP port is set to Auto Negotiation AN 10 HDX with the following modes advertised 10H The UTP port is set to Manual Negotiation and is forced to 100F The UTP port is set to Manual Negotiation and is forced to 100H The UTP port is set to Manual Negotiation and is forced to 10F The UTP port is set to Manual Negotiation and is forced to 10H MAN 100 FDX MAN 100 HDX MAN 10 FDX MAN 10 HDX Figure C Speed and Duplex Settings SW6 SW7 A B BACKPLANE ENABLE The NMM2 can be configured for In Band or Out of Band management When the Backplane Enable switch is in the DS position factory default the front panel UTP management port is enabled and the Backplane Ethernet Port is disabled This is defined as Out of Band management When the DIP switch is in the EN position the Backplane Ethernet Port is enabled This is defined as In Band management This allows Ethernet Backplane connectivity to adjacent modules via the chassis Backplane A or B depending on the switch setting Refer to the full version User Manual for the appropriate A B backplane config
6. uration settings SW8 RESERVED NOTE DIP switches marked Reserved must be kept in the Left factory default position 2 INSTALL MODULE IN CHASSIS AND CONNECT CABLES a Itis recommended that the NMM2 be installed in Slot 1 Carefully slide the module into the open slot in the chassis Align the module with the installation guides and ensure that the module is firmly seated against the backplane Secure the module by fastening the front panel thumbscrew push in and turn clockwise to tighten to the chassis front Verify the Pwr LED is ON indicating the chassis is powered b Connect the UTP port via a Category 5 cable to a 10BASE T or 100BASE TX Ethernet device Management Station 3 CONFIGURE MODULE VIA COMMAND LINE INTERFACE To access the Command Line Interface CLI connect the NUM2 RS 232 Serial Console Port to the COM port of a computer equipped with terminal emulation software such as HyperTerminal The Console Port DCE is a mini DIN 6 female connector which can be changed to a DB 9 connector with the included adapter The NMM2 Console Port is a Standard RS 232 asynchronous serial interface Start HyperTerminal and select the correct COM Port in the HyperTerminal Connect To window Set the serial port to the following Bits Per Second 57 600 Stop Bits 1 Data Bits 8 Parity NONE Hardware Flow Control NONE Once connected press lt ENTER gt to bring up a command line prompt on the attached PC Anew NMM2
Download Pdf Manuals
Related Search