MA-5288H
Contents
1. 8x8 HDMI Matrix Switcher with Full 3D Support User Manual Compliance ae rev 130701 fel VI Made in Taiwan CIELE visual interface Doors zp JACH I dts ao TR D AUDIO Safety and Notice The MA 5288H 8x8 HDMI Matrix Switcher with Full 3D Support has been tested for conformance to safety regulations and requirements and has been certified for international use However like all electronic equipments the MA 5288H should be used with care Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit e Follow all instructions and warnings marked on this unit e Do not attempt to service this unit yourself except where explained in this manual e Provide proper ventilation and air circulation and do not use near water e Keep objects that might damage the device and assure that the placement of this unit is on a stable surface e Use only the power adapter and power cords and connection cables designed for this unit e Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning ESD CAUTION TABLE OF CONTENTS INTRODUCTION seenneeee RR E 1 FEATURES csseseenneteet RR EE 1 PACKAGE CONTENTS cc TREE EE 1 SPECIFICATIONS cce DEDE 2 PANEL DESCRIPTIONS TREND EEQOQEE 3 HARDWARE INSTA2. DEFAULT EDID Begin default EDID selection LEARN EDID Begin EDID learning from one output CLEAR Clear the previous IR operation procedure TAKE Trigger the previous setting F1 Reserved F2 Reserved Mute Output Ex Mute Output 3 Output Status Ex Output 4 Input 2 Save Current Mapping Ex Save current mapping to 5 Preset Mapping Ex Preset saved mapping from 5 Learn default EDID Ex Default EDID 2 Input 3 Learn Output EDID Ex Learn Output 4 Input 3 Mute Output Number 1 8 Take 1 Press MUTE button 2 Press output number key 3 to select Output 3 3 Press TAKE button Status Output Number 1 8 Take 1 Press STATUS button 2 Press output number key 4 to select Output 4 3 Press TAKE button Save Output Number 1 8 storage site Take 1 Press SAVE button 2 Press output number key 5 to select the storage site 5 3 Press TAKE button Preset Output Number 1 8 storage site Take 1 Press PRESET button 2 Press output number key 5 to select the storage site 5 3 Press TAKE button Default EDID Output Number 1 8 default EDID Input Number input 1 8 Take 1 Press DEFAULT EDID button 2 Press output number key 2 to select default EDID 2 3 Press input number key 3 to select Input 3 4 Press TAKE button Learn Output Number Output 1 8 Input Number input 1 8 Take 1 Press LEARN button 2 Press
3. Panel Push in Button Please refer to the Operation Approach Method A Push in Button Page 6 2 IR Remote Control Please refer to the Operation Approach Method B IR Remote Control Page 7 8 3 Software Control Please refer to the Operation Approach Method C Software Control through RS 232 port Page 11 12 There are eight embedded default EDID as below Full HD 1080p 60 24bit 2D amp 2ch Full HD 1080p 260 24bit 2D amp 7 1ch Full HD 1080p 60 24bit 3D amp 2ch Full HD 1080p 260 24bit 3D amp 7 1ch HD 1080i 60 720p 60 24bit 2D amp 2ch HD 1080i960 720p 260 24bit 2D amp 7 1ch Full HD 1080p 260 36bit 2D amp 2ch Full HD 1080p 60 36bit 2D amp 7 1ch CO N O OFF A Cc N Q Can every TV work with the HDMI matrix A Basically the answer is YES But if your TV can not support 1080p please refer the EDID LEARNING section to learn EDID from your TV Q What is EDID Why do I need to learn EDID A EDID contains the whole information of the display such as the resolution and audio setting which this display can support Therefore based on the EDID information media player will pick up the most suitable resolution and audio setting to the display In order to faithfully transmit the EDID information from display to the media player learning EDID from display to this device is necessary Q What should I do to learn EDID for the matrix A Due to the limitation of HDMI the source device can only o
4. output number key 4 to select Output 4 3 Press input number key 3 to select Input 3 4 Press TAKE button OU Ow O I UN N e Q O1 Qu o o1 U success fail success F fail Method C Software Control through RS 232 port Ethernet port 1 System Requirement 1 OS Information MS WinXP 7 2 Baud rates 9600 3 Software size 3 MB 4 Minimum RAM requirement 256 MB 1 2 3 Ec IND DU 5 iad 6 il d 2 Ie CS oO Gp Ss oO e m e p Oum E UPDATE 4 RESET 990000900 i dcin a Woven 5 D Firmware Update Buton TI NeworcButon IMamigBubn Defaut ResetBwon mout Switch Buton TA Power onorBution A Muto Output Buon 2 Step by step for connecting matrix and controller otep1 Use RS 232 cable to connect the RS 232 port on matrix and PC otep2 Open the software and then choose the correct com port Step3 Click connection button Step4 Make sure the connection status is on connected status PST 3 FW SW Version Button Click button to show version information Version Info E3 Software version 4X4CB SW 00 01 Firmware version 4X4CB FW 00 02 4 RS 232 Button 1 Click E button to switch to RS 232 function 2 If RS 232 is connected the button will show the sign image to let you know 5 Ethernet Button 1 Click E button to switch to Ethernet function 2 If Ethernet is connected the button
5. pull out and reconnect the power input connector Step6 Click Start button and the firmware will start writing 12 Network Button a FIRMWARE DEFAULT G EDID RWWARE NETWORK Q MAPPING step1 Make sure the connection status is on connected status grp step2 Connect matrix to network through IP control port otep3 Click NETWORK Button and then will be a pop up windows otep4 Click Read From Device to read the device IP address step5 Select Ethernet button and then will be a pop up windows IP Address otep6 Key in the device IP address to the pop up windows and click OK step7 Click the Connect Button h connect then you start control by Ethernet Remark Switch controlling by clicking the shortcut button Ethernet Button Click the button and then click Connect Button to start a RS 232 Button k Click the button and then click Connect Button to start 13 Mapping Button Mapping Configuration Save Mapping Preset Mapping To Mapping 1 From Mapping1 I Rename Mapping Configuration 1 Configuration 2 Configuration 3 Configuration 4 Mapping 1 Mapping2 Mapping3 Mapping4 Configuration 5 Configuration 6 Configuration 7 Configuration 8 Mapping5 Mapping Mapping 7 Mappings 1 Save Mapping a Select Mapping 1 8 b Click Save button to save current mapping 2 Preset Mapping a Select M
6. will show the sign image to let you know 6 COM Port Selection COM COM 4 Click Y button to select COM Port 7 Connection Status com Ea wj eee o 1 7 7 NA a 1 Connected Status Connected ee 2 Connecting Status Gonnectind 3 Disconnected Status MASE i sce is 8 Connect Disconnect Button Click this button s to change connection status COM COM4 w Connected 9 Power On Off Button Click this button to power on off i 0 Power on status Blue Click this button to power off device Standby Mode E 0 Power off status Red Click this button to power on device ED 10 EDID Button DEFAULT RESET Learn EDID from Default View EDID From 1 Full HD 1080p 60 24bit 2D amp 2ch From Input 1 v EDID Information Load EDID File To Input 1 Learn EDID from Display From HDMI Output 1 To Input 1 Create EDID File 1 Learn EDID from Default a Select Default EDID 1 8 Default EDID b Select Input c Click Learn button to learn default EDID 2 Load EDID File to Input a Select Input b Click Load button to select the EDID file 3 Learn EDID From Display a Select HDMI output b Select Input c Click Learn button to learn display EDID 4 Create EDID File a Click Create button to create EDID file 3D Support Activates 3D lution Aspect 4 3 Resolution Add Format VESA Audio Resolution Audio T
7. 1x Rack mounting ear set e 1x Installation software CD e 1x User Manual Additional IR remote controllers and IR blasters can be purchased as optional accessories to control the HDMI sources located separately SPECIFICATIONS Model Name MA 5288H Role of usage True 8x8 matrix Surround sound up to 7 1ch or stereo digital audio 1 Human body model 19kV air gap discharge amp 12kV contact discharge ESD protection 2 Core chipset 8kV PCB stack up 4 layer board impedance control differential 1000 single 50 emma MAeSEH 00000 440 x 156 x 44mm 17 3 x 6 1 x 1 7 Dimensions 524 x 265 x 76mm 20 6 x 10 4 x 3 542 x 411 x 300mm 21 3 x 16 2 x 11 8 20839 71 7o Weight 3062g 6 8 bs 1RU rack mount with ears Wall hanging holes Power supply 12V 5A DC Operation temperature 0 40 C 327104 F Storage temperature 20 60 C 4 140 F Relative humidity 20 90 RH no condensation L x W x H PANEL DESCRIPTIONS Front Panel 1 Source Status Input source indicator LED 2 IR SENSOR IR sensor for receiving the IR commands from IR remote 3 Output Push Button amp 7 segment LED Front panel push buttons used to select the number of display channel amp LED display for output ports 4 Input Push Button amp 7 segment LED Front panel push buttons used to select the number of input source amp LED display for input channels Rear Panel IN j ec bil F __
8. LLATION eene 4 CONNECTION DIAGRAM aaaea a 4 OPERATION APPROACH ssesoresssscermersserereerstiereneereteereteeres a E REEEEEES 5 EDID LEARNING aanmeren nnee eean e aeaea aeae ratae Tesan aaea tana e A mee 16 n ete 17 INTRODUCTION The MA 5288H 8x8 HDMI Matrix Switcher with Full 3D Support provides the most flexible and cost effective solution in the market to route high definition video sources plus multi channel up to 7 1 channel digital audio from any of the four HDMI sources to the remote displays at the same time This solution is well suited for use in home theater conference room presentation systems or other similar setting or application FEATURES e Support HDMI Deep Color amp full 3D e HDCP compliant e Allows any source to be displayed on multiple displays at the same time e Allows any HDMI display to view any HDMI source at any time e Supports 7 1 channel digital audio e Supports default HDMI EDID and learns the EDID of displays e The matrix master can switch every output channels to any HDMI inputs by push in button IR remote control RS 232 control and Ethernet control e Easy installation with rack mounting and wall mounting designs for master and receiver respectively e Fast response time 2 5 seconds for channel switch PACKAGE CONTENTS e 1x MA 5288H e 1x IR Receiver e 1x DC 12V 5A e 1x IR Remote control e
9. ____ _ so E 12V DC 12V DC power jack OUTPUT 1 8 HDMI outputs INPUT 1 8 HDMI inputs System IR Receiver Ext IR receiver RS 232 RS 232 control port 10 Ethernet Ethernet control port O O N Oo C HARDWARE INSTALLATION MA 5288H as master 1 Connect all sources to HDMI Inputs on the 8x8 HDMI Matrix MA 5288H 2 Connect all display to HDMI Outputs on the 8x8 HDMI Matrix MA 5288H 4 Connect the 12V 5A DC power supply to the 8x8 HDMI Matrix MA 5288H CONNECTION DIAGRAM m HDMI RS 232 mmm CAT5 5e 6 IR incoming MA 5288H IR Receiver RS232 CABLE e e a g o g go g N m lt m Wim ILI CAT 5 5e 6 Flat Panel Display Blu ray Player OPERATION APPROACH Method A Push in Button preset d ae save MT Prt UTP S IF a IP L S learn default 1 IN OUT MAP 1 Use the or output push button to select the number of display 2 Use the or input push button to select the number of input source change selected input output port in ascending order change selected input output port in descending order After you select the desired input output port the LED will blink twice and the setting will be effective 2 Save Mapping Mode 1 Keep pushing output save button until the output LED shows d to enter the Save Mapping Mode 2 Use the or input push button to select the mapping configurat
10. apping 1 8 b Click Recall button to recall previous mapping which are saved 3 Rename Mapping a Rename the mapping Mapping1 Mapping8 b Click Confirm button to confirm the change 14 Default Reset Button Click this button to do factory default reset The default reset process will take about 80 90 seconds ED 15 In Out Switch Button Click the button on the checkerboard to select Input amp Output port User can click the input number button to let all outputs select the same input Ex All outputs select input 3 A OA Kc Bn BOG Bw 16 Mute Output Button Click the circle button to turn off output s video and audio Ex Mute Output 2 o CNBERERE e EDID LEARNING The EDID learning function is only necessary whenever you encounter any display on the HDMI output port that cannot play audio and video properly Because the HDMI source devices and displays may have various level of capability in playing audio and video the general principle is that the source device will output the lowest standards in audio format and video resolutions to be commonly acceptable among all HDMI displays In this case a 720p stereo HDMI signal output would be probably the safest choice Nevertheless the user can force the matrix to learn the EDID of the lowest capable HDMI display among others to make sure all displays are capable to play the HDMI signals normally There are THREE methods to do EDID Learning as below 1 Front
11. e input learn button before the setting is effective The LED will show 0 0 if the setting is success The LED will show F F if the setting is failure 5 EDID Learning Mode Push input learn button to select the input channel which you want to learn EDID from HDMI output and then keep pushing input learn button when you select your desired input channel Push the or output push button and then the LED will show E L one time to enter Learn Output EDID Mode Use or output push button to select the output port number Release input learn button after selecting the desired output port number and then the LED will blink twice and the setting will be effective It will quit the Learn Output EDID Mode if you push the input default button before the setting is effective The LED will show 0 O if the setting is success The LED will show F F if the setting is failure Method B IR Remote Control 1 IN OUT Switch 7 Segment LED IN OUT Switch Output Number 1 8 Input Number 1 8 Ex Input 2 1 Press output number key 3 to select Output 3 To Output 3 2 Press input number key 2 to select Input 2 DS UQ oo00 o 90 eoo000 NdN 2 Function Key OFF Standby mode ON Power on the matrix switcher MUTE Turn off output s video and audio STATUS Preset output status SAVE Save current mapping mode PRESET Preset mapping mode
12. fore the best method is to learn EDID from the amplifier directly Please refer to EDID LEARNING section and follow the steps to learn the EDID When learning EDID from the amplifier user just needs to connect the matrix and amplifier Please don t connect HDMI cable between amplifier and TV when the EDID learning is proceeding Q When play the same content upon multi displays why only the TV equipped with amplifier can have 7 1ch audio and the others don t have 7 1ch audio even no stereo A Due to the limitation of HDMI the source only can choose one video and one audio format to play which can be either 1080p and 7 1ch or 1080p and stereo audio It means when the user sets the matrix at 1080p and 7 1ch the source will only play the content under this format Therefore if the TV cannot decode 7 1ch audio there is definitely no audio WARRANTY The SELLER warrants the MA 5288H 8x8 HDMI Matrix Switcher with Full 3D Support free from defects in the material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer Should this product fail to be in good working order within 1 year warranty period The SELLER at its option repair or replace the unit provided that the unit has not been subjected to accident disaster abuse or any unauthorized modifications including static discharge and power surge This warranty is offered by the SELLER for its BUYER with direct transaction only This warranty is void if
13. ion 1 8 which you want to save current input output mapping 3 After you select the desired mapping configuration number the LED will blink twice and the mapping setting will be saved 4 If you push the output preset button before the mapping setting is saved the LED will show to quit the Save Mapping Mode 3 Preset Mapping Mode 1 Keep pushing output preset button until the output LED shows P to enter the Preset Mapping Mode 2 Use the or input push button to select the saved mapping configuration 1 8 which you want to recall 3 After you select the desired mapping configuration number the LED will blink twice and the mapping setting will be effective 4 If you push the output save button before the mapping setting is effective the LED will show to quit the Preset Mapping Mode 4 Default EDID Mode Push input default button to select the input channel which you want to learn default EDID and then keep pushing input default button when you select your desired input channel Push the or output push button and then the LED will show E d one time to enter Learn Default EDID Mode Use or output push button to select the default EDID mode 1 8 Release input default button after selecting the desired default EDID mode and then the LED will blink twice and the setting will be effective It will quit the Learn Default EDID Mode if you push th
14. the warranty seal on the metal housing is broken Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for 90 days from the day of reshipment to the BUYER If the unit is delivered by mail customers agree to insure the unit or assume the risk of loss or damage in transit Under no circumstances will a unit be accepted without a return authorization number The warranty is in lieu of all other warranties expressed or implied including without limitations any other implied warranty or fitness or merchantability for any particular purpose all of which are expressly disclaimed Proof of sale may be required in order to claim warranty Customers outside Taiwan are responsible for shipping charges to and from the SELLER Cables and power adapters are limited to a 30 day warranty and must be free from any markings scratches and neatly coiled The content of this manual has been carefully checked and is believed to be accurate However The SELLER assumes no responsibility for any inaccuracies that may be contained in this manual The SELLER will NOT be liable for direct indirect incidental special or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages Also the technical information contained herein regarding the MA 5288H features and specifications is s
15. ubject to change without further notice
16. utput one format of video and audio In other words the source device cannot output 720p and 1080p video at the same time or output stereo and surround sound at the same time Therefore you may need to manually setup each HDMI input for desirable audio video output format The mechanism of EDID Learning is to pick up the HDMI display with the lowest capability among the ones you would use for this input source For example if user would like to play the Input 2 upon output 2 output 8 and output 4 and only output 3 cannot support 1080p support up to 720p only please learn the EDID from the display connected to the output 3 at the Input 2 port Of course if outot 3 would get the HDMI signals from every HDMI input please learn EDID information from output3 to all four HDMI inputs For more information about EDID Learning please refer to EDID LEARNING section My TV can support 1080p but why there is no audio gt The factory default EDID of this device is 1080p amp 2ch audio However there would be a problem after you change to use 1080p amp 7 1ch if the TV cannot support 7 1ch audio Please use the default EDID 1080p amp 2ch audio Q When set an audio amplifier AV receiver between TV and the matrix to extract 7 1ch audio but why there is still no audio A Basically the default EDID of the chosen input can support 7 1ch audio but the problem is that the EDID of the amplifier still cannot match the default setting There
17. ype Stereo Frequency Content 44 1kHz Monitor Name 13 Character EDID Content Save EDID on Computer b Select the EDID content c Click Save EDID on Computer to save the generated EDID as a file 5 View EDID content a Select Input HDMI output or From File b Click View button to read the EDID and analysis View EDID From Input 1 v EDID Information Manufacturer ID MIT 720x400 70 Hz 640x480 60 Hz 640x480 67 Hz 640x480 72 Hz 640x480 75 Hz 800x600 56 Hz 800x600 60 Hz 800x600 72 Hz 800x600 75 Hz 832x624 75 Hz 1024x768 60 Hz 1024x768 870 Hz 1024x768 75 Hz 1280x 1024 75 Hz 1152x870 75 Hz Resolution 1600 x 1200 amp 60 Resolution 1600 x 900 amp 60 Resolution 1680 x 1050 amp 60 Resolution 1440 x 90060 Resolution 1360 x 765 60 Resolution 1280 x 960 60 Resolution 1280 x 800 860 Resolution 1280 x 720260 Descriptor Block 1920x1080 60Hz Descriptor Block 1920x 1200 60Hz Monitor name HDMI Matrix Illl v c Click Save As to save the read EDID as a file on computer KD 11 Firmware Update Button DEFAULT RESET Step1 Make sure RS 232 is connecting and the connecting status is otep2 Click FIRMWARE UPDATE Button and then will be a pop up windows File Size Progress Step3 Click Load File to select the firmware file which you want to update Step4 Click Break button Step5 Quickly
Download Pdf Manuals
Related Search
MA 5288H ma 528 purdue