- Microgate
Contents
1. between 10 and 30 Volts which is able to supply at least 30W peak power and about 2W average power A car battery guarantees several days autonomy Important note the adaptor ACC062 for the RadioSpeed displayboard is not suitable for outdoor use Consequently Microgate does not accept any responsibility for damage to persons or things due to incorrect use of the adaptor 1 3 1 Battery Recharge If the batteries are low either the discharge recharge or the immediate recharge procedure can be carried out In the first case the batteries are first discharged and only subsequently recharged This allows the batteries to maintain their original capacity over a long period To select discharge recharge keep the START STOP MODIFY CHARGE DISCHARGE button on the control panel pressed down for at least 2 seconds with the displayboard switched off after connecting an external power source to the connector SUPPLY The operation will take from a minimum 7 hours to a maximum of about 10 hours depending on the initial battery charge level If you choose immediate recharge instead the operation will last about 7 hours However although this type of recharge takes less time it should only be used in exceptional circumstances as it shortens the life of the batteries To select immediate recharge keep the yellow LAP RESET SETUP DIRECT CHARGE button on the control panel pressed down for at least 2 seconds with the displayboard switched o2. ALPHANUMERIC DISPLAYBOARD RadioSpeed User Manual Version 1 0 MICRO amp GATE Microgate S r l Via Stradivan 4 39100 BOLZANO pa http www microgate i RadioSpeed Displayboard User Manual MICRO GATE RadioSpeed Displayboard User Manual 3 INDEX ALPHANUMERIC DISPLAYBOARD RADIOSPEELD 4 1 1 CONTROL PAN BE 1 1 1 1 1 1 1 at 5 1 2 CONNECTIONS zacon 1 1 1 1 1 1 00 6 1 3 POWER SUBPEY 1 E etree aie nase rae 0 7 1 3 1 Battery ya 7 1 4 RADIOSPEED FIRMWARE 2200300 see srs SEERE ES ENS 9 1 4 1 Firmware Updating s lt 7 26 9 5 SPEEDME PERS cist cis oth bo tae bk Sh ha EA aha ul se 10 1 MICRO GATE 1 RadioSpeed Displayboard ALPHANUMERIC DISPLAYBOARD RADIOSPEED MICRO GATE RadioSpeed Displayboard User Manual CONTROL PANEL SUPPLY 5 6 SERIAL Green button START STOP MODIFY DISCHARGE CHARGE used for e modification of values in program setting keep pressed down for fast forward e selection of battery discharge and recharge 7 pole A
3. ff after connecting an external power source to the connector SUPPLY In both recharge modes it is possible to interrupt the process by pressing the START STOP and LAP RESET keys simultaneously MICRO GATE RadioSpeed Displayboard User Manual 8 The LOW BATTERY led on the control panel tells you the battery charge status the type of power source used and the recharge operation status when the battery is being recharged EXTERNAL SUPPLY STATUS LED LOW BATTERY e Displayboard On or Off Green Green Pause e Batteries Charged Displayboard On or Off Green Red Pause e Batteries Discharged INTERNAL SUPPLY BATTERY STATUS LED LOW BATTERY Displayboard Off 01 e Batteries Charged or Discharged Displayboard On Green Pause Green Pause e Batteries Charged Displayboard On Red Pause Red Pause e Batteries Discharged CHARGE DISCHARGE STATUS LED LOW BATTERY e Start of Discharging Pause Red Pause Red FAST e Discharging Over Start of Recharging Pause Green Pause Green FAST e Recharging Over Green DIRECT CHARGE STATUS LED LOW BATTERY e Start of Recharging Pause Green Pause Green FAST e Recharging Over Green MICRO GATE RadioSpeed Displayboard User Manual 9 1 4 RADIOSPEED FIRMWARE Every time it is switched on RadioSpeed displays the firmware version stored at that mome
4. mphenol or plug socket connector for external power supply and battery recharge Yellow button LAP RESET SETUP DIRECT CHARGE used for e confirmation of program settings e selection of immediate battery recharge selection Internal battery status signal Led 6 pole Amphenol input output connector for Serial On Off switch MICRO GATE 1 1 oar 7 pole Amphenol Connector 6 pole Amphenol Connector User Manual CONNECTIONS MICRO GATE RadioSpeed Displayboard SUPPLY 7 pole Amphenol Ground Ground Ground External supply input 8 25V External supply input 8 25V External supply input 8 25V Remote on off input SERIAL 6 pole Amphenol SERIAL RS232 TX output SYNC IN SERIAL RS485 RX input SERIAL RS485 RX input Ground SERIAL RS232 RX input 1 2 23 6 0 Q RadioSpeed Displayboard User Manual 7 1 3 PowER SUPPLY Power can be supplied in three ways By connecting the RadioSpeed displayboard to the MICROGATE battery charger In this way it is possible to keep the batteries charged at the same time This guarantees perfect functioning also when the mains power supply is interrupted e By using the internal batteries of the displayboard In this case autonomy is usually above 30 hours of continuous functioning depending on the type of display used By connecting the displayboard to any continuous current supply whether steady or not
5. nt ET FIRMWARE TYPE FIRMWARE VERSION Figure 1 As can be noted in Figure 1 the Firmware Version consists of 2 the two numbers It is important to provide the MICROGATE staff with this number if you require technical assistance 1 4 1 Firmware updating Free RadioSpeed Firmware updating is possible by downloading the latest versions from the site http www microgate itor requesting them from MICROGATE Once the update file has been obtained the operations to be performed are simple Switch off RadioSpeed Press the START STOP MODIFY e LAP RESET SETUP buttons simultaneously and while keeping them pressed down switch on the displayboard attention the power supply must be disconnected before switching on the displayboard the led on the displayboard should slowly blink red green Connect the PC serial to the RadioSpeed SERIAL connector using the 20m CAB010 cable or the 2m CAB001 From the PC run the uFlasher program containing the latest Firmware version During programming the LOW BATTERY led on the displayboard turns ORANGE After about 2 minutes programming is over uFlasher shows the message Device successfully programmed At this point the led turns GREEN The RadioSpeed Firmware has been successfully updated Now you can switch off the displayboard A B Any error in programming is indicated by the LOW BATTERY led on the displayboard which turns RED In the unlikely eventuality that thi
6. s should happen simply repeat the procedure indicated above MICRO GATE RadioSpeed Displayboard User Manual 10 1 5 SPEEDMETER This mode allows you to measure the speed on the basis of any length The speed is calculated on the basis of the measurement of the time interval between two START STOP impulses So you need only place two photocells at the desired distance and set them to the Start and Stop If the bidirectional mode has been set the measurement base can be run in both directions Bidirectional mode is not recommended if it is not essential The system is able to manage up to 20 transits at the same time in the measurement base Setup is possible to set the length of the measurement base the reset time and the mono or bidirectional mode Keep LAP SETUP pressed for at least two seconds to enter Setup km 0 Set the kilometers with START MopIFY Press LAP SETUP m 0 Set the meters with START MODIFY Press LAP SETUP cm 0 Set the centimeters with START MODIFY Press LAP SETUP Rst Press LAP SETUP M 0 Set the minutes with START MODIFY Press LAP SETUP S 0 Set the seconds with START MODIFY Press LAP SETUP Bi 0 Set bidirectional mode using START MODIFY 0 No 1 Yes Press LAP SETUP MICRO GATE MICRO amp GATE Microgate S r l Via Stradivari 4 39100 BOLZANO ITALY http www microgate it
Download Pdf Manuals
Related Search