Trantec S5 Wireless Microphone Series
Contents
1. Headphone monitoring as standard XLR switchable mic and line and 4 jack AF outputs AF processing menu S5 5 only Over 1400 customer selectable channels Fully integrated PC software monitoring facility via USB port All metal construction of receiver and transmitters Rack kit and front mounting antenna adaptors included S5 5 only Page 2 S5 Wireless Microphone Installation Guide Rev 1 5 Safety Our aim is to Supply you with a product that provides you with countless hours of trouble free use In order to achieve this goal we recommend the following Keep the system away from direct sources of heat e g Central heating radiators heaters and direct sunlight Do not expose the unit to an environment where it could be splashed with liquids as this may result in fire or electric shocks Should the transmitters remain unused for an extended period of time we recommend that the batteries are removed to avoid any potential leakage Keep the system clean by using a slightly damp cloth Never use household cleaning agents or solvents Avoid using or storing the system in damp conditions Always use the AC power adaptor supplied with the receiver and always disconnect from the AC outlet when not in use Never remove the external covers of the equipment exposing the electronics or modify the unit in any way Do not handle the mains lead with wet hands Never pull the cord of the AC adaptor always grasp the main body of th2. Jog Wheel Now rotate the Jog EXIT Tu Wheel to adjust the mute setting DECCA ang 1s Men es RX SETTINGS MUTE AUDIO PILOT marker shows the current mute setting in relation to the RF A and B scales Please note high mute settings will decrease range and low mute settings increase the interference potential We Mute 6 recommend a setting of 4 to 6 The pci mm mute level changes in real time as the na setting is varied ee EXIT PHANTOM Lc I Ff ee Oe Audio Processing S5 5 only Press the Jog Wheel to enter the Rx SETTINGS MAIN MENU Rotate till RX SET is MUTE AUDIO PILOT underlined then press On the RX EXIT PHANTOM LCD SETTINGS menu rotate till AUDIO is underlined and press Options PROCESSING AUDIO PROCESSING available here are PHASE REV PHASE REUB LL x i UTO LoCUT and HiBOOST The default EXIT HiBOOSTO factory setting for all these options is OFF Navigate to each option by rotating the Jog Wheel and press to check the box for each option when it is underlined PHASE REV reverses the audio output phase LoCUT reduces the low frequency response HIBOOST increases the high frequency response Page 11 S5 Wireless Microphone Installation Guide Rev 1 5 All three of the above functions AUDIO PROCESSING change in real time as the option is PHASE REV A LoCUTo selected Rotate the Jog Wheel to EXIT HiBOOSTO underline EXIT after making your ces selections and press
3. away from the transmitters at all times Always ensure the transmitters are separated by at least 50 cm Never position the transmitter antenna directly against the body or the hand This will reduce the operating range Ensure the correct setting of the Mute for effective control of interference whilst the transmitter is turned off The default is normally 5 but may need to be increased with multi channel set ups Do not mix separate Banks in multi channel set ups Use the SCAN function to check for external interference Set the transmitter AF gain so the receiver VU indicates 0 db with occasional peaks to 6 dB Keep the microphone instrument lead away from the antenna on the beltpack Do not mix with other brands of Wireless Microphone as Trantec cannot guarantee multi channel compatibility Page 19 S5 Wireless Microphone Installation Guide Rev 1 5 Troubleshooting Guide e No operation of Transmitter Replace the current battery with a fresh one of the correct Alkaline AA type e No RF signal on receiver Check the transmitter and receiver are Tuned to the same channel e Poor range Check the mute level setting For normal range we recommend a mute setting of 4 6 e AF Signal distorted Check the receiver XLR mic line switch for a correct match to your Mixer Amplifier Reduce the gain of the transmitter if the VU meter shows over 6aB e AF Signal low level with high background noise Adjust the tra
4. complete with all necessary connecting leads for 4 channels A 19 rack tray is available as an accessory for mounting one or two ADU units Trantec recommends that a maximum of 12 channels is wired as illustrated below For larger installations please consult www trantec co uk To channels 9 12 ANT B ANT A ATO RIITISSBA a FIL 2E 1 1 I CHA N UTAN BPF TETE oe 2e I m CHA N TAN A Ae RANA TE 2 sec sd AASA CHAF i i ai c E ir a i s Sii Lupe Taare Page 23 S5 Wireless Microphone Installation Guide Rev 1 5 Antenna Head Amplifiers Trantec head amplifiers are designed to reduce the effect of long RF antenna cable runs between the receivers or ADUs and remote antennae The S ADU and S5 Series Receiver can supply power to the head amplifier Please note head amplifiers can introduce some unwanted effects such as RF blocking and increased intermodulation especially in multi channel applications To minimise such effects Trantec offers the following guidelines 1 For cable runs of greater than 10 M and less than 20 M when using RG58 cable insert a head amplifier attenuation 830 MHz is approx 5 dB per 10 M For cable runs of greater than 20 M and less than 40 M when using RG213 cable insert a head amplifier attenuation 830 MHz is approx 2 5 dB per 10 M 40 M is the recommended maximum length of cable run Ensure that transmitters are always at least 3 M from the r
5. 3 AF Hi Z Pin 4 Internal AF load resistor Link pins 3 and 4 and connect screened cable to pin 1 ground and pins 3 and 4 as illustrated Page 26 S5 Wireless Microphone Installation Guide Rev 1 5 Technical Specifications Overall System Frequency Bands available A1 692 722 MHz B1 722 752 MHz B2 740 752 MHz C1 794 830 MHz C2 794 806 MHz D1 863 865 MHz D2 854 865 MHz 5 3 only D3 830 865 MHz E1 668 698 MHz F1 636 666 MHz G1 606 638 MHz 85 5 only G2 606 622 MHz S5 3 only RF Switching BW 36 MHz typ RF grid spacing 25 kHz RF Bandwidth lt 200 kHz AF Frequency response 60 Hz 20 kHz AF Distortion lt 0 8 at nom deviation 22 kHz AF Dynamic range gt 110 dBA AF Noise reduction Trantec proprietary Temperature range 10 C to 55 C Receiver Specification Type Dual Diversity featuring PLL Dual Double conversion receivers IF Freq 1 IF 55 875 MHz 2nd IF 10 7 MHz Sensitivity lt 1 uV 12 dB SINAD Ist Image gt 70 dB RSSI range 10 steps 30 dB range Antenna Inputs TNC 50 Q AF switches Low Cut High Boost Phase Reversal S5 5 only AF Output level XLR Line 15 dBm max XLR Mic 25 dBm max Unbalanced 4 jack socket 9 dBm max Antenna Phantom 9 V 60 mA short circuit protected on each RF port Bank Specification 10 banks x 24 channels S5 5 6 banks Japanese version 9 banks x 12 channels 5 3 Infra Red Link Range 15 cm max Computer Interface Computer monitoring via
6. accessory for S5 3 systems 1 Unscrew 3 x lid retaining screws M3x6 from the front left side of the chassis viewed from the front and fit the small angled rack bracket using the supplied screws There are 3 of these supplied with each receiver 2 Unscrew 3 x lid retaining screws M3x6 from the front right side of the chassis and fit the supplied long angled bracket using the screws supplied 3 Fit the 2 supplied antenna extension cables into the front panel long bracket and tighten their TNC nuts Screw the TNC plugs of each into the antenna sockets on the rear of the receiver Should front mount antennae not be required fit the 2 plastic blanking plugs supplied into the spare holes Page 22 S5 Wireless Microphone Installation Guide Rev 1 5 Multi Channel Configuration with ADU The S5 series is designed for simultaneous use of several systems Ensure each system is assigned a different operating channel Use only channels from one bank to ensure multi channel compatibility Try to ensure that each transmitter is separated by 0 5 M 1 5 ft during operation It is recommended that for systems with 4 or more channels the Trantec Antenna Distribution Unit ADU is used This allows the use of only one set of antennae to feed several receivers Each ADU is capable of driving 4 units simultaneously with separate outputs for additional ADU units The diagram below shows a typical 12 channel installation Each ADU comes
7. rear panel USB interface Power Consumption 300 mA 12 Vdc nominal Beltpack Transmitter Specification Power Supply Single Alkaline AA cell 1 5 V nom Power consumption typically 120 mA Operating time typically 8 10 hrs min Controls On Off AF Gain Adjust Frequency adjust Gain Range 2 dBm to 20 dBm in 10 steps Dimensions 55 mm x 80 mm x 20 mm Weight 110 g Due to our continual policy of research and development we reserve the right to alter specifications without prior notice Page 27 S5 Wireless Microphone Installation Guide Rev 1 5 Lavalier Microphone Specification Directional Characteristics Omni Directional Frequency 50 Hz 18 kHz Element Back Electret Condenser Sensitivity 54 dB 3 dB Impedance 4 KQ 30 at 1kHz Dimensions 10 5 x 24 7 mm Cable 1 3 Mx 2 2 mm Connector 4 Pin Mini XLR Weight 20 5 g excl accessories Dynamic Handheld Specification Power Supply Single Alkaline AA cell 1 5 V nom Power consumption typically 120 mA Operating time typically 8 10 hrs min Capsule Audio Technica MU 36B Element Moving Coil dynamic Polar Pattern Hyper Cardioid Frequency Response 100 10000 Hz Sensitivity 51 dB 3 dB Controls On Off AF Gain Adjust Frequency adjust AF Mute Gain Range 3 steps 6 dB Dimensions 32 mm x 250 mm Weight 350 g Grille diameter 51 mm Condenser Handheld Specification Power Supply Single Alkaline AA cell 1 5 V nom
8. to return to the main screen __ p m c a Mili Headphone Volume Rotate the Jog Wheel while the HERDPHONE main screen is showing to go to the INI headphone volume adjustment A bar a RNBAZIIZINAI graph of the volume is shown and can be altered by again turning the Jog Wheel Push to exit and return to the main screen The unit will return to the main screen automatically if there is no user intervention for approximately 2 seconds Any change you have made will be saved Scanning The scanning feature can determine which frequencies are currently being used in the vicinity of your receiver From the main screen press the Jog Wheel to go to MAIN MENU rotate till FREQ SEL is underlined and push Then rotate till SCAN is underlined and push The scanning process takes about 10 seconds and you will then be shown the Bank selection screen If interference is found on a frequency during the scan the bank containing that frequency is made unavailable on the receiver You can then select any bank from those available and any frequencies from within those banks m m m hh Eo hj SLHNNM ING Page 12 S5 Wireless Microphone Installation Guide Rev 1 5 Pilot Tone iiia MX SETTINGS The S5 series has the ability to MUTE AUDIO PILOT disable the pilot tone as a means of EIT PHANTOM LCD either identifying outside interference or allowing compatibility with non pilot tone devices The default fac
9. Installation Guide Lolo Le i ard Crrantec Contents 20 Di 22 23 24 20 26 27 28 29 30 Introduction System Overview Safety Important Instructions Getting Started Receiver Set Up Receiver Frequency Selection Miscellaneous Settings Handheld Transmitter Set Up Beltpack Transmitter Set Up Operating Hints Troubleshooting Guide Rack Mount Kit Multi Channel Configuration with ADU Antenna Head Amplifiers Mini XLR Wiring Connections Technical Specifications Warranty CE Declaration of Conformity WEEE Statement Page 1 S5 Wireless Microphone Installation Guide Rev 1 5 Introduction The Trantec S5 series represents our commitment to our customers by providing high quality reliable Wireless audio links using our considerable design expertise gained over many years as a leading edge manufacturer We would like to thank you for purchasing this product and would like you to study this guide especially the safety instructions before installing and using this equipment S5 Series System Overview The S5 series is a professional UHF wireless microphone system with features including 24 channel simultaneous operation 5 3 12 channel 10 preset banks including 1 custom user 55 3 9 Banks True dual receiver diversity to minimise drop outs Intuitive LCD and operating system on both receiver and transmitter Infra red programming for fast system set up Software transmitter function locks
10. Power consumption typically 120 mA Operating time typically 8 10 hrs min Element Electret condenser capsule Polar Pattern Cardioid Frequency Response 90 Hz 20 kHz Sensitivity 51 dB 3 dB Controls On Off AF Gain Adjust Frequency adjust AF Mute Gain Range 3 steps 6 dB Dimensions 32 mm x 233 mm Weight 300 g Grille diameter 51 mm Due to our continual policy of research and development we reserve the right to alter specifications without prior notice Page 28 S5 Wireless Microphone Installation Guide Rev 1 5 Warranty All Trantec products are guaranteed for a period of 12 months from the date of purchase against defects in materials and workmanship In the event of a claim under guarantee the product should be returned in its original packing to an Authorised Service Centre or BBM Electronics together with proof of purchase i e sales purchase receipt from an authorised dealer BBM will repair or replace the device at its discretion BBM offers no warranty whatsoever under the following circumstances mechanical damage incorrect operation incorrect voltage wear and tear and defects that were known at the time of purchase In addition the warranty will be null and void in the event of unauthorised repair or modification including removal of any of its covers E amp OE Due to our continual policy of research and development we reserve the right to alter specifications without prior notice Trantec Sy
11. Rotate the Jog Wheel till TX SET is Tx SETTINGS underlined and press to enter TX FREQUENCY gi ICK SETTINGS With FREQUENCY PE underlined press the Jog Wheel All Align the transmitter and receiver infra red windows with the transmitter no more than 15 cm from SEND BANK 4 TO Tx ali19n IR Windows the receiver With SEND underlined PE AL CANCEL press the Jog Wheel and wait a few seconds All frequencies in the bank selected will be transferred to the transmitter and its current frequency will be set to match the receiver s current frequency The receiver will return to its main display For S5 5 If the receiver is currently in a SINGLE or USER frequency it will transfer the USER bank For Japanese units only fixed banks 1 to 6 are available For S5 3 If the receiver is currently in a SINGLE frequency it will transfer Banki Page 10 S5 Wireless Microphone Installation Guide Rev 1 5 Miscellaneous Settings RX Settings Mute Squelch Settings The S5 series uses sophisticated internal mute functions including Pilot Tone Noise and RSSI to prevent noise break through from external sources when the transmitter is in the OFF position The RSSI Received signal strength portion is user adjustable via the RX SETTINGS MENU To Access this press the Jog Wheel for 1 second and enter the MAIN MENU or for 3 seconds if not in mute press With MUTE underlined press FREQ SEL Ru the
12. cient magnitude to constitute a risk of electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the litera ture accompanring the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION TO PREVENT ELECTRIC SHO CE DO NOT USE THIS POLARIZEIN PLUG WITH AN EXTEN SION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN EE BULLY IH SERTED TO PREVENT BLADE EXPOSURE NOTE SINCE THIS PRODUCT IS PLUGGARLE EQUIPMENT THE SOCcKEET OUTLET MUST BE IN STALLED NEAR THE EGUIFMENT AND SHOULD BE EASILY ACCESSIBLE Page 4 S5 Wireless Microphone Installation Guide Rev 1 5 Getting Started The S5 series is a high quality fully featured wireless microphone system with many features including an intuitive operating system To enable you to get started we recommend you initially set up the system as outlined in the next few pages Receiver Set Up DG inlet 1 4 jack output DC strain relief Mic Line switch USB port XLR output ol i TRANTE Wi SS Rear View LCD Jog wheel Diversity switch A B indicators Infra red port Power switch indicator Mute indicator Power On Off Headphone output 830 400MHz BK1 01 Mute 5 RFS MUTE ww LEE S a eee eee e aaa anadate aa Front View Page 5 S5 Wireless Mi
13. crophone Installation Guide Rev 1 5 1 Attach the 2 supplied antennae to the rear panel TNC antenna connectors as shown left 2 Connect the AC DC adaptor into i the DC inlet as marked on the rear panel feeding the cable through the attached strain relief Observe that the front panel on off switch surround is illuminated red 3 Connect the rear panel audio output from either the 1 jack or XLR to your mixing console or amplifier Note the XLR balanced output can be switched for either mic or line The system can be also monitored from the headphone socket using the Jog Wheel to adjust the volume level 4 Switch the On Off switch to the On position The switch surround will now be illuminated green and the receiver will default to its initial setting BK1 01 The system is now ready for use Page 6 S5 Wireless Microphone Installation Guide Rev 1 5 Receiver Frequency Selection Frequency Selection Options 1 To change the selected channel in BANK1 Press and hold the Jog wheel for approximately 3 seconds if the receiver is not in mute to enter the MAIN MENU You will enter the MAIN MENU immediately if the receiver is in mute With FREQ SELECT underlined press the Jog Wheel Rotate the Jog Wheel till BANK is underlined and press Press to select BANK1 Rotate the Jog wheel to change the channel Finally press to select the new frequency See the attached frequenc
14. d the Power On LED located in the end cap is illuminated 4 Check For Received Signal Check that the display indicates the same channel as the receiver The receiver should now show a received signal on its RF bar graphs and after 20 seconds the transmitter battery status 5 Gain Adjustment Turn on the transmitter and wait for the flashing decimal point on the LCD to stop flashing Press the Up or Down buttons al y to increase or decrease the head TRANTEC sensitivity The display will show 0 1 or 2 with 0 gain being for max SPL 6 Frequency Adjustment Turn on the transmitter and adjust the frequency whilst the decimal point is flashing approx 6 secs via the Up or Down buttons When the correct frequency is selected turn the transmitter off then on again to activate the newly selected channel Page 15 S5 Wireless Microphone Installation Guide Rev 1 5 7 Mute Switch Incorporated in the handheld end cap is a Power On LED and Audio Mute switch To mute the audio flick the switch towards the LED Power On LED Page 16 S5 Wireless Microphone Installation Guide Rev 1 5 Beltpack Transmitter Set Up Power switch Power LED i Battery Infra red port compartment Uw Down LED Battery indicator Antenna 1 Battery Fitting Open the battery compartment by sliding the door forward and up Insert a battery observing the correct polarity as shown The do
15. e frequency G31 00MH z will be flashing Rotate the Jog T Wheel to select this section of a new HUCEPT frequency and press to accept The second part of the frequency will now GJA F239 MHz start flashing Change the second part of the new frequency as above You AECEPT can then change each letter of the user name in the same way All ASCII characters are available for the user name If you wish to exit this menu at any time press and hold the Jog Wheel Press the Jog Wheel for 1 second to exit then rotate till ACCEPT is underlined and press to select the new custom frequency and user name Go to the next step to program a transmitter via the receiver infra red port Please note For S5 3 product the single user frequency will be added to the transmitter with receiver Bank1 The S5 3 does not have USER bank In the case of the S5 5 it will be added to the Custom USER bank You can download USER banks via the Trantec software Please refer to the software manual on this CD for more information Units for the Japanese market do not have USER or SINGLE options in the FREQUENCY SELECT menu Page 9 S5 Wireless Microphone Installation Guide Rev 1 5 4 Program a transmitter with Bank information via receiver Infra red port Press and hold the Jog wheel for approximately 3 seconds if the receiver is not in mute to enter the MAIN MENU You will enter the MAIN MENU immediately if the receiver is in mute
16. e unit when connecting disconnecting to an AC power outlet Route the AC power lead in such a way that it is not likely to be stepped on or tripped over Do not use if the AC power lead becomes damaged A damaged AC lead may cause fire or give you an electric shock Never touch any part of the system during a thunderstorm as this may result in severe electric shock Dispose of batteries responsibly Do not break open or incinerate and do not place in household waste Consult your local waste authority for advice on disposal Should the covers be removed or there is any other breach of the above instructions the warranty becomes null and void in addition to personal risk from burns and or electric shock If any of the following conditions occur when using the unit switch off and remove the AC adaptor from the AC outlet immediately and contact your nearest dealer Smoke or unusual smell Water or foreign metallic object inside unit Physically damaged housings Page 3 S5 Wireless Microphone Installation Guide Rev 1 5 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi
17. emote receiver antennae at any time Always test the installation without the use of head amplifiers first Only insert these if the range is found to be inadequate and below normal operating range Always ensure that the overall system RF gain does not exceed 6 dB Always insert head amplifiers at the remote antenna end of the installation The antenna head amplifier is NOT designed for outdoor installation and should not be operated in damp conditions Page 24 S5 Wireless Microphone Installation Guide Rev 1 5 Mini XLR Wiring Connections Beltpack Audio Mini XLR Connections Ground Bias 5 V AF Hi Z AF Load Resistor sae Pin 1 Ground Pin 4 Load 22 K Ohms XA TT Pin 2 Blas 5 V Pin 3 AF Input Solder connections for Mini XLR flying socket 4 Page 25 S5 Wireless Microphone Installation Guide Rev 1 5 Wiring for Mini XLR Flying Socket 2 Wire Mic Pin 1 Ground ee Pin2 5V Pin 3 AF Pin 4 Internal AF load resistor Link pins 3 and 4 and add a 10 KQ bias resistor as illustrated Link 3 Wire Mic Pin 1 Ground Pin2 5V Pin 3 AF Pin 4 Internal AF load resistor Link pins 3 and 4 as illustrated Hi Impedance Guitar Instrument Pin 1 Ground Pin 2 5 V Not connected ae Pin 3 AF Hi Z AE Pin 4 Not connected O Connect screened cable to pin 1 O ground and pin 3 AF Hi Z A 2 Link Lo Impedance Microphone No Phantom Pin 1 Ground Pin 2 5 V Not connected Pin
18. gain ona transmitter or accidentally turning a transmitter off during a performance you can lock these features from the receiver Press the Jog Wheel to show the MAIN MENU Rotate the Jog Wheel to underline TX SET and push to select this option Rotate the Jog Wheel till LOCK is underlined and push to select LOCK this Push the Jog Wheel to check the POWERS I box for POWER if required or rotate to te Li go to FREQ GAIN and push to check this box if required LUC QUERO Rotate till EXIT is underlined and push PUWE Re You will then have the option to SEND the TX Locks you have selected to a transmitter or CANCEL If you are sending Locks to a transmitter you should hold it within 15cm of the receiver and with the infra red windows of each aligned Page 14 S5 Wireless Microphone Installation Guide Rev 1 5 Handheld Transmitter Set Up TIDE axa ID End cap Power On Position Up Down Grille Sleeve Infra red port Frequency Battery indicator 1 Opening The Microphone Undo the handheld sleeve by unscrewing the end cap at the base anti clockwise and then gently sliding the sleeve down to expose the LCD and Battery compartment 2 Battery Fitting Place an Alkaline AA cell into the battery compartment noting the correct polarity as shown on the label in the compartment 3 Switch On slide the On Off switch to the On position and observe the display is on an
19. nsmitter gain so the VU bar graph shows 0dB with 6dB peaks e External Head amplifiers not operating Check for shorts in the leads and ensure the receiver PHANTOM PWR is switched on via the RX SETTINGS menu e Receiver LCD contrast poor Enter the receiver RX SETTINGS menu select LCD and press then rotate the Jog Wheel to adjust the contrast The receiver will automatically exit after a few seconds Page 20 S5 Wireless Microphone Installation Guide Rev 1 5 S5 Series Rack Mount Kit 19 Rack Mounting for 2 x S5 Series Receivers The rack mounting kit is supplied as standard with S5 5 systems or is available as an accessory for S5 3 systems 1 Unscrew the front 3 lid retaining screws from opposite sides of each receiver case and fit the angled rack brackets using the supplied screws There are 3 of these supplied with each receiver 2 Remove the 2 plastic plugs from the top of the receiver lid and fit a metal joining strip 2 supplied per receiver in the slots at the side of each lid of the 2 receivers Carefully fit the M3x6 screws 1 supplied with each receiver coloured black 3 Fit 2 joining strips across the bottom of the receiver chassis using 4 M3x6 CSK screws 2 supplied per receiver Page 21 S5 Wireless Microphone Installation Guide Rev 1 5 19 Rack 1 x S5 Series Receiver with Front Mount Antennae The rack mounting kit is supplied as standard with S5 5 systems or is available as an
20. or is marked with a Battery 2 Antenna Fitting Screw the antenna into the antenna bush 3 Microphone Plug a mic into the Mini XLR socket 4 Switch On Flick the On Off switch to the On position and observe the display is on and the battery LED illuminated Check the display indicates the same channel as the receiver 5 Check For Received Signal The receiver should now show a received signal on its RF bar graphs and after 20 seconds the transmitter battery status Page 17 S5 Wireless Microphone Installation Guide Rev 1 5 6 Beltpack AF Gain Adjusment Turn the transmitter on and wait for the flashing decimal point on the LCD to stop flashing Press the Up or Down buttons firmly to increase or decrease the AF gain There are 10 steps with 0 being minimum 7 Frequency Adjustment Turn the transmitter on and adjust the frequency while the decimal point is flashing approx 6 secs via the Up or Down buttons When the correct frequency is selected turn the transmitter off then on again to activate the newly selected channel Page 18 S5 Wireless Microphone Installation Guide Rev 1 5 Operating Hints To maximise operating performance Trantec recommends the following Ensure good line of sight between the receiver antennae and transmitter and avoid obstructions e g concrete walls and metal structures Always ensure the receiver antennae are at least 3 M 10 ft
21. stems BBM Electronics Group Ltd Kestrel House Garth Road Morden Surrey SM4 4LP UK Tel 44 0 20 8330 3111 Fax 44 0 20 8330 3222 E Mail enquiries trantec co uk Web http www trantec co uk Page 29 S5 Wireless Microphone Installation Guide Rev 1 5 CE Declaration of Conformity C 0891 This equipment is in compliance with the essential requirements and other relevant provisions of Directives 1999 5 EC 89 336 EC or 73 23 EC More information is available from www trantec co uk IMPORTANT NOTICE Before using this wireless microphone system please observe the requirements of each country with respect to frequency allocations and individual licensing requirements WEEE Statement must be disposed of separately from normal waste at the end of its operational life Please dispose of this product by taking it to your local recycling or collection point ps This symbol indicates that this piece of electrical electronic equipment BBM Electronics Group Ltd www trantec co uk A subsidiary of TOA Corporation Page 30 S5 Wireless Microphone Installation Guide Rev 1 5
22. tory setting is ON PILOT TONE To disable Pilot Tone press the Jog PILUT TONE Wheel to go to MAIN MENU Rotate till RX SET is underlined and push to go to the RX SETTINGS menu Rotate the Jog Wheel to underline PILOT TONE PILOT and press to uncheck the box Press Exit Rotate the Jog Wheel to exit this Ball screen and press to return to the main screen TMGAIORIFOWGF RX SETTINGS MUTE AUDIO PI DC added to the antenna inputs for EXIT PHANTOM powering head amplifiers The default I factory setting is OFF Push the Jog Wheel to show the MAIN MENU Rotate the Jog Wheel to underline RX SETTINGS and push to show the next menu Rotate to underline PHANTOM PUR PHANTOM and push Press to check ieee yt the PHANTOM PWR box Rotate and METE AR then press to choose EXIT and return to the main screen LCD Contrast Push the Jog Wheel to bring up the uit te MAIN MENU Rotate the Jog Wheel LED CONTRAST to underline RX SETTINGS Rotate to RSTSTette nananana underline LCD and push then rotate the Jog Wheel to alter the LCD CONTRAST Push to exit and return to the main screen The unit will return to the main screen automatically if there is no user intervention for approximately 2 seconds Any change you have made will be saved Page 13 S5 Wireless Microphone Installation Guide Rev 1 5 TX Settings Lock TX Switch To prevent unauthorised or accidental changes of frequency or
23. y table Page 7 S5 Wireless Microphone Installation Guide Rev 1 5 2 To change the selected Bank Press and hold the Jog wheel for approximately 3 seconds if the receiver is not in mute to enter the MAIN MENU You will enter the MAIN MENU immediately if the receiver is in mute With FREQ SELECT underlined press the Jog Wheel This will give you the next menu Rotate the Jog Wheel until BANK is underlined and press to give you the Bank selection screen below right Rotate the Jog Wheel to underline a new bank then press to select Press to select the frequency shown or rotate to change to another frequency within this bank Press again with ACCEPT underlined to accept the new bank See the attached frequency table Go to step 4 to program the transmitter via the receiver infra red port Page 8 S5 Wireless Microphone Installation Guide Rev 1 5 3 To change the selected channel to a Custom single frequency This option allows the customer to select 1 of over 1400 available channels Press and hold the Jog wheel for approximately 3 seconds if the receiver is not in mute to enter the MAIN MENU You will enter the MAIN MENU immediately if the receiver is in mute With FREQ SELECT underlined FREQUENCY SELECT press the Jog wheel With SINGLE SINGLE T USER BANK underlined press the Jog wheel ESITE SCAN With EDIT underlined press the Jog wheel The first part of th
Download Pdf Manuals
Related Search