Compact Prime and Zoom lenses ZEISS Mount Change Instructions
Contents
1. 9 Now remove the lens from the camera 10 Remove the EF mount and EF adapter ring cf section C 2 4 11 Determine the total thickness of the shims that are already installed in the lens groove Increase or decrease the total shim thickness according to the tables in the appendix by using a flat bladed screw driver or a pair of tweezers 12 Place the black EF adapter ring on the lens barrel and tighten the screws using a torque of 0 4 Nm 13 The next step is to place the silver EF mount on the EF adapter ring and tighten the screws wl using a torque of 0 4 Nm 14 Recheck the flange focal distance of the lens see section D in combination with the camera you use E Appendix Table for shims to adjust Compact Prime CP 2 lenses when used on digital cameras Shim color Thickness mm silver 0 013 Ee gold 0 019 BN purple 0 025 EE light blue 0 032 eT red 0 038 SSS blue 0 051 T white 0 064 D o S S green 0 076 PE orange 0 102 N light purple 0 127 ES clear 0 152 Example Using a Compact Prime CP 2 35mm T2 1 lens with an EF mount scaled in feet and a test chart at a test distance of 4 ft an actual distance of 4 ft 1 is measured Due to the table on page 14 a silver shim 0 013 mm must therefore be added to the total thickness of the shims Note Any combination of shims is possible to achieve the required thickness and therefore2. Accessories and spare parts All interchangeable mount sets include mount lens caps adaption ring with support bracket screws and a set of shims CP 2 EF mount Indent No Interchangeable Mount Set EF for CP 2 18 T3 6 1846 490 Interchangeable Mount Set EF for CP 2 21 T2 9 CP 2 25 T2 1 CP 2 28 T2 1 or CP 2 35 T2 1 1846 492 Interchangeable Mount Set EF for CP 2 15 T2 9 CP 2 35 T1 5 SuSp CP 2 50 T1 5 SuSp 1846 494 CP 2 50 T2 1 CP 2 65 1 1 5 Susp or CP 2 85 T 2 1 Interchangeable Mount Set EF for CP 2 50 T2 1 Macro 1846 496 Interchangeable Mount Set EF for CP 2 100 T2 1 CF 1846 499 Interchangeable Mount Set EF CP 2 135 T2 1 1998 731 PL mount Interchangeable Mount Set PL for CP 2 18 T3 6 1846 489 Interchangeable Mount Set PL for CP 2 21 T2 9 CP 2 25 T2 1 CP 2 28 T2 1 or CP 2 35 T2 1 1846 491 Interchangeable Mount Set PL for CP 2 15 T2 9 CP 2 35 T1 5 SuSp CP 2 50 T1 5 SuSp 1846 493 CPZ 50 T2 1 CP 2 65 1 1 5 SuSp or CP 2 85 T 2 1 Interchangeable Mount Set PL for CP 2 50 T2 1 Macro 1846 495 Interchangeable Mount Set PL for CP 2 100 T2 1 CF 1846 498 Interchangeable Mount Set PL CP 2 135 T2 1 1998 730 F mount Interchangeable Mount Set F for CP 2 15 T2 9 1998 736 Interchangeable Mount Set F for CP 2 18 T3 6 1871 042 Interchangeable Mount Set F for CP 2 21 T2 9 CP 2 25 T2 1 CP 2 28 T2 1 or CP 2 35 T2 1 1871 043 Interchangeable
3. E incl screws 1856 667 Torx torque wrench T6 torque moment 0 4 Nm 0520 065 Torx Pan Head screw M2 x 8 SUS 410 50 pcs 500 022 Front Lens Cap Focal Lengths 18 85mm amp 100mm CF 0097 227 Front Lens Cap Focal Length 50mm Macro 1775 836 Rear Lens Cap EF 1793 167 Rear Lens Cap PL 102160 0052 000 Rear Lens Cap F 1793 178 Rear Lens Cap MFT 1889 118 Rear Lens Cap E 1907 145 Siemens Star test chart DIN A3 laminated 1849 755 Set of shims CP 2 1853 634 juawdojanap jed uyra Hulobuo jo jjnsaJ e se pue Alantjap Jo adods pue ublisap ul abupun o p fqns 00d ZLOZ IIA ZD MW Auewad ul pajulid WSL OL0 OL NA Phone 49 7364 20 6175 Fax 49 7364 20 4045 Carl Zeiss AG Camera Lenses 73446 Oberkochen Germany www zeiss com cine
4. the lens barrel 7 When the torx screws have been tightened the lens can be fitted to a camera with a PL mount and used 8 Check the flange focal distance of the lens see section D in combination with your camera screw of the lens barrel Instructions on changing to an EF or to any other CP 2 mount 4 Please note the correct orientation of the Micro 4 3 and the E mount to the serial number on the lens barrel 1 Ensure that the groove on the rear side of the black EF adapter ring fits over the small screw of the lens barrel 5 Tighten the torx screws using a torque of 0 4 Nm 2 Place the silver EF mount on the EF adapter ring in such a way that the blue dot on the mount has the same orientation as the ZEISS logo and the support bracket points to the serial number on the lens barrel D Adjusting the lens to your camera As the flange focal distance varies from camera type to camera type it is necessary to adjust the CP 2 lens to the camera used when changing the mount or camera model shimming In order to perform this adjustment Carl Zeiss provides shims in different thicknesses that are color coded When the mount has been unscrewed these shims can be placed in a groove in the lens barrel Any possible combination of shims can be used to achieve the required thickness and therefore the required flange focal distance The lens already contains shims when delivered Car
5. 0 03 Compact Prime CP 2 85 T2 1 and CP 2 85 T1 5 Super Speed Meter distance scale Feet distance scale Distance to test chart mm 1500 Distance to test chart ft 5 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 1492 0 03 Aft 11 4 8 0 05 1494 0 02 Aft 11 5 8 0 04 1496 0 02 Aft 11 6 8 0 02 1498 0 01 4ft 11 7 8 0 01 1500 0 00 5ft 0 0 00 1502 0 01 5ft 1 8 0 01 1504 0 02 5ft 2 8 0 02 1506 0 02 5ft 3 8 0 04 1508 0 03 5ft 4 8 0 05 Compact Prime CP 2 100 T2 1 CF Meter distance scale Feet distance scale Distance to test chart mm 2000 Distance to test chart ft 7 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 1987 0 04 6ft 11 4 8 0 03 1990 0 03 6ft 11 5 8 0 02 1993 0 02 6ft 11 6 8 0 02 1997 0 01 6ft 11 7 8 0 01 2000 0 00 7ft 0 0 00 2003 0 01 7ft 1 8 0 01 2007 0 02 7ft 2 8 0 02 2010 0 03 7ft 3 8 0 03 2013 0 04 7ft 4 8 0 03 Compact Prime CP 2 135 T2 1 Meter distance scale Feet distance scale Distance to test chart mm 2000 Distance to test chart ft 7 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total wa
6. 1075 0 05 Aft 3 0 02 1100 0 04 Aft 4 0 03 12 Compact Prime CP 2 21 T2 9 Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 940 0 04 3ft 8 0 04 955 0 03 3ft 9 0 03 970 0 02 3ft 10 0 02 985 0 01 3ft 11 0 01 1000 0 00 Aft OI 0 00 1015 0 01 Aft 1 0 01 1030 0 02 4ft 2 0 02 1045 0 03 Aft 3 0 03 1060 0 04 Aft 4 0 04 Compact Prime CP 2 25 T2 9 and CP 2 25 T2 1 Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 960 0 03 3ft 8 0 05 970 0 02 3ft 9 0 04 980 0 02 3ft 10 0 03 990 0 01 3ft 11 0 01 1000 0 00 Aft 0 0 00 1010 0 01 Aft 1 0 01 1020 0 02 Aft 2 0 03 1030 0 02 Aft 3 0 04 1040 0 05 Aft 4 0 05 Compact Prime CP 2 28 T2 1 Meter distance scale Feet distance scale Compact Prime CP 2 50 T2 1 CP 2 50 T2 1 Macro and CP 2 50 T1 5 Super Speed Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at b
7. A e fig I 7 Compact Prime and Zoom lenses ZEISS Mount Change Instructions We make it visible A Adjusting the flange focal distance to the lens Congratulations on the purchase of this Compact Prime CP 2 lens set We are convinced that your new lenses will bring you much pleasure and success The Compact Prime CP 2 lenses are the latest members of the ZEISS family of lenses for digital and film cameras They deliver great flexibility by introducing interchangeable mounts that allow the lenses to be used with a wide range of cameras from traditional cine to HDSLR systems Available in five different mounts PL EF F Micro 4 3 and E this new family of ZEISS lenses enables cinematographers to be completely free in their choice of camera systems The Compact Prime CP 2 lenses cover the full frame image format without vignetting In this manual we take a Compact Prime CP 2 35mm T 2 1 with EF mount scaled in feet as an example to explain how to change a lens mount and the subsequent matching of your lens to a DSLR camera Proceed in the same sequences to switch to any other CP 2 mount B Overview General instructions m The use of a T6 torque wrench with a torque of 0 4 Nm is strongly recommended This wrench can be purchased from Carl Zeiss see appendix page 17 m Ensure that the environment is clean and free from dust so that no dust particles can enter the lens during the following procedure m Smudges and fi
8. Mount Set F for CP 2 35 T1 5 SuSp CP 2 50 T1 5 SuSp CP 2 50 T2 1 1871 046 CP 2 50 T2 1 Macro CP 2 85 T1 5 SuSp or CP 2 85 T 2 1 Interchangeable Mount Set F for CP 2 100 T2 1 CF 1871 044 Interchangeable Mount Set F CP 2 135 T2 1 1998 732 Micro 4 3 mount Interchangeable Mount Set MFT for CP 2 18 T3 6 1889 230 Interchangeable Mount Set MFT for CP 2 21 T2 9 CP 2 25 T2 1 CP 2 28 T2 1 or CP 2 35 T2 1 1889 231 Interchangeable Mount Set MFT for CP 2 15 T2 9 CP 2 35 T1 5 SuSp CP 2 50 T1 5 SuSp 1889 232 CP 2 50 7 2 1 CP 2 85 T1 5 SuSp or CP 2 85 T 2 1 Interchangeable Mount Set MFT for CP 2 50 T2 1 Macro 1889 233 Interchangeable Mount Set MFT for CP 2 100 T2 1 CF 1889 234 Interchangeable Mount Set MFT for CP 2 135 T2 1 1998 733 18 E mount Indent No Interchangeable Mount Set E for CP 2 18 T3 6 1907 608 Interchangeable Mount Set E for CP 2 21 T2 9 CP 2 25 T2 1 CP 2 28 T2 1 or CP 2 35 T2 1 1907 609 Interchangeable Mount Set E for CP 2 15 T2 9 CP 2 35 T1 5 SuSp CP 2 50 T1 5 SuSp 1907 610 CP 2 50 1251 CP 2 85 T1 5 Susp or CP2 85 T 2 1 Interchangeable Mount Set E for CP 2 50 T2 1 Macro 1907 611 Interchangeable Mount Set E for CP 2 100 T2 1 CF 1907 612 Interchangeable Mount Set E for CP 2 135 T2 1 1998 735 ZEISS Diopters Diopter 0 5 meter feet 1430 420 Diopter 1 0 meter feet 1430 399 Diopter 2 0 meter feet 1430 309 Accessories Support Bracket EF F MFT
9. est focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 960 0 04 3ft 10 0 03 970 0 03 3ft 10 1 2 0 03 980 0 02 3ft 11 0 02 990 0 01 3ft 11 1 2 0 01 1000 0 00 Aft OI 0 00 1010 0 01 Aft 1 0 01 1020 0 02 Aft 1 1 2 0 02 1030 0 03 4ft 2 0 03 1040 0 04 4ft 2 1 2 0 03 Compact Prime CP 2 35 T2 1 and CP 2 35 T1 5 Super Speed Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 980 0 03 3ft 10 0 05 985 0 02 3ft 10 1 2 0 04 990 0 02 3ft 11 0 03 995 0 01 3ft 11 1 2 0 01 1000 0 00 Aft 0 0 00 1005 0 01 Aft 1 0 01 1010 0 02 Aft 1 1 2 0 03 1015 0 02 Aft 2 0 04 1020 0 03 Aft 2 1 2 0 05 14 Distance to test chart mm 1500 Distance to test chart ft 5 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 1480 0 03 Aft 11 0 03 1485 0 02 Aft 11 1 4 0 03 1490 0 01 Aft 11 1 2 0 02 1495 0 01 Aft 11 3 4 0 01 1500 0 00 5ft OI 0 00 1505 0 01 5ft 1 4 0 01 1510 0 01 5ft 1 2 0 02 1515 0 02 5ft 3 4 0 03 1520 0 03 5ft 1
10. l Zeiss recommends that the camera Is set to the usual standard settings cf works settings You can obtain further details from the instruction manual of the camera you use Procedure In the following chapter we explain how to adjust your Compact Prime CP 2 to a DSLR camera 1 Fasten the Carl Zeiss test chart on a wall at the appropriate test distance see tables on page 12 16 the test distance is depending on the focal length and ensure that the illumination is bright and uniform 2 Mount the camera and lens on a tripod and level the camera making sure that the centre of the image is aligned with the centre of the Siemens star 3 Activate the live view of your camera select the maximum magnification 4 Set the distance ring to the test distance according to the tables in the appendix This setting must not be changed during the adjustment process 5 Set the aperture of the lens to full speed 6 Obtain maximum image sharpness on the live view by varying the distance between the test chart and the camera 7 Now remeasure the distance between the image plane mark on the camera body and the test chart the actual distance find od fi 8 If the distance has changed the flange focal distance of the lens must be adjusted by using the colored shims You find a list of tables in the appendix for each focal length to calculate the resultant change of the flange focal distance
11. ngerprints on the lens surface can be gently removed with a soft brush and then with a dry and clean cotton cloth The ZEISS lens cleaning kit will give superior results and is highly recommended for this purpose m When matching the lens ensure that the colored shims lie on top of each other in the groove of the lens barrel and do not cover the screw holes m Please handle the shims carefully as they can easily kink or tear which makes them unusable General drawing Ea Lens H Groove of the lens barrel Shim EJ Adapter ring with attached silver support bracket BH Mount including threaded black inner ring e g EF D Torx screws C Changing the mount 1 Remove the rear lens cap A 2 Remove the four torx screws of the silver EF mount with a T6 torque wrench and place the mount and the screws on one side The size of the black inner ring depends on the focal length of the lens and is securely fastened to the EF mount or F MFT or E Mount at the factory 3 Remove the eight torx screws of the black EF adapter ring and place the ring and the screws on one side The silver support bracket is already installed on the EF adapter ring at the factory and does not need to be removed ep 4 Now you see the colored shims in the groove of the black lens barrel 5 Place the PL mount on the lens in such a way that the groove on the rear side of the PL mount fits over the silver screw on
12. sher thickness mm 1992 0 05 6ft 11 4 8 0 06 1994 0 03 6ft 11 5 8 0 05 1996 0 02 6ft 11 6 8 0 03 1998 0 01 6ft 11 7 8 0 02 2000 0 00 7ft 0 0 00 2002 0 01 7ft 1 8 0 02 2004 0 02 7ft 2 8 0 03 2006 0 03 7ft 3 8 0 05 2008 0 05 7ft 4 8 0 06 16 Compact Zoom CZ 2 70 200 T2 9 Meter distance scale Feet distance scale Distance to test chart mm 4500 Distance to test chart ft 15 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 4460 0 09 14ft 10 0 11 4470 0 07 14ft 10 1 2 0 08 4480 0 04 14ft 11 0 06 4490 0 02 14ft 11 1 2 0 03 4500 0 00 15ft 0 0 00 4510 0 02 15ft 1 2 0 03 4520 0 04 15ft 1 0 06 4530 0 07 15ft 1 1 2 0 08 4540 0 09 15ft 2 0 11 Compact Zoom CZ 2 28 80 T2 9 Meter distance scale Feet distance scale Distance to test chart nm 2000 Distance to test chart ft 7 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 1960 0 07 7ft 10 0 10 1970 0 06 7ft 10 1 2 0 07 1980 0 04 7ft 11 0 05 1990 0 02 7ft 11 1 2 0 02 2000 0 00 7ft 0 0 00 2010 0 02 7ft 1 2 0 02 2020 0 04 7ft 1 0 05 2030 0 06 7ft 1 1 2 0 07 2040 0 07 7ft 2 0 10 Compact Prime and Zoom lenses
13. the desired flange focal distance Always use the closest possible combination of shims Tables for adjusting the flange focal distance of Compact Prime CP 2 lenses All Compact Prime CP 2 lenses cover the full frame image format 36 x 24 mm ANSI Super 35 and Normal 35 image format except the CP 2 18mm T3 6 This lens covers the APS H image format Key Minus sign Shims must be removed Plus sign Shims must be added Compact Prime CP 2 15 T2 9 Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at best Change of total Object distance Change of total focus mm washer thickness mm at best focus ft washer thickness mm 860 0 04 3ft 4 0 04 895 0 03 3ft 6 0 03 930 0 02 3ft 8 0 02 965 0 01 3ft 10 0 01 1000 0 00 Aft 0 0 00 1035 0 01 4ft 2 0 01 1070 0 02 4ft 4 0 02 1105 0 03 4ft 6 0 03 1140 0 04 4ft 8 0 04 Compact Prime CP 2 18 T3 6 Meter distance scale Feet distance scale Distance to test chart mm 1000 Distance to test chart ft 4 Object distance at best focus mm Change of total washer thickness mm Object distance at best focus ft Change of total washer thickness mm 900 0 04 3ft 8 0 03 925 0 03 3ft 9 0 02 950 0 02 3ft 10 0 01 975 0 01 3ft 11 0 01 1000 0 00 Aft 0 0 00 1025 0 01 Aft 1 0 01 1050 0 02 Aft 2 0 01
Download Pdf Manuals
Related Search