Manual for POE-151
Contents
1. PLANET IEEE 802 3af Power over Ethernet Injector POE 151 User s Manual e fP y m i O nr Trademarks Copyright PLANET Technology Corp 2006 Contents subject to revision without prior notice PLANET is a registered trademark of PLANET Technology Corp All other trademarks belong to their respective owners Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC Warning This equipment has been tested a2. iner a a ND a ee at 4 T4 SPECIFICA HON cereo T A a a i 5 TO PRODUC T OUTLOOK tada dada iden 5 2 HARDWARE INSTALLATION ua A A 6 2 ERROR INS TADA MON a ee NG ee ee a e eto 6 2 1 1 Belore Stan UD a diia 6 212 POE 151 Me Inector Instala Me seie a a E a A 7 2 1 3 POE 151 and POE 151S the IEEE 802 3af Injector and Splitter installation 7 2 1 4 Gonnect with IEEE 802 3af devias did 8 3 TROUBLESHOCOTINCG O aE e 9 APPENDIX A NETWORKING CONNECTION Qu ccecceeceeceeceeceeceecceceeccesceseeceeceeeceseeseuscasensenseusenseneceeeeeseeeees 10 A 1 SWITCH S RJ 45 PIN ASSIGNMENTS 0cceccecceceececcecceceecccuececnecececeecueaeeaececueaesaeceesesaesaeseesesaesnesueaeeneaeeas 10 A 2 RJ 45 CABLE PIN ASSIGNMENT reas 10 1 INTRODUCTION 1 1 Checklist Thank you for purchasing our POE 151 IEEE 802 3af Power over Ethernet Injector your Power over Ethernet Injector package shall contains following contents Check the contents of your package for following parts e Power over Ethernet Injector x1 e User s manual CD x1 Power Adapter x1 e Power cord x 1 If any of these pieces are missing or damaged please contact your dealer immediately if possible retain the carton including the original packing material and use them against to repack the product in case there is a need to return it to us for repair 1 2 About the Power over Ethernet Injector The POE 151 is an IEEE 802 3af Power over Ethernet In
3. of POE 151S to the RJ 45 port of remote device 3 Connect proper DC plug from DC OUT of POE 151S to remote device 4 Power on the remote device and the LED indicator on POE 151S will remains on the screen in Figure 3 appears 100 meters Data Power a00 POE 151 POE 151S WAP 4000 Figure 3 Connection architecture over POE 151 151S A Notice 1 According to IEEE 802 3af standard the POE 151 will not inject power to the cable if not connecting to IEEE 802 3af devices 2 Please ensure the output voltage is correct before applying power to remote device 2 1 4 Connect with IEEE 802 3af devices Due to the capability of IEEE 802 3af standard the POE 151 can directly connect with any IEEE 802 3af end nodes like wireless access point VoIP phones and Internet camera where support IEEE 802 3af In line Power over Ethernet port The screen in Figure 4 appears 100 meters Data Power POE 151 WAP 4060PE Figure 4 Connection to IEEE 802 3af device Once POE 151 detects the existence of an IEEE 802 3af device the LED indicator will be steady ON to shows it is providing power A Notice If the connected device is not fully complying with IEEE 802 3af standard or in line power device the LED indicator of POE 151 will not be steady on 3 TROUBLESHOOTING This chapter contains information to help you solve problems If the Switch is not functioning properly make sure the Ethernet Switch was set
4. up according to instructions in this manual The PoE LED is not lit Solution Check the cable connection between POE 151 and IEEE 802 3af device Can the POE 151 work with Gigabit Ethernet device Solution The POE 151 use 4 wire for data transmission pair 1 2 pair 3 6 and 4 wire for power supply pair 4 5 pair 7 8 thus Gigabit Ethernet device connect to POE 151 will not send data over the power wire and the transmit speed shall change to 100Mbps Why connect my PoE device to POE 151 and it cannot power on Solution 1 Please check the cable type of the connection from POE 151 to the other end The cable should be an 8 wire UTP Category 5 or above EIA568 cable within 100 meters A cable with only 4 wire short loop or over 100 meters all will affect the power supply 2 Please check and assure the device that fully complied with IEEE 802 3af standard APPENDIX A NETWORKING CONNECTION A 1 Switch s RJ 45 Pin Assignments RJ 45 Connector pin assignment MDI MDI X Contact Media Dependant In Media Dependant In terface terface Cross it Rx receive TX transmit DC current 7 8 Ground Remark Gigabit Ethernet is not allowed to use POE 151 since pair 4 5 and pair 7 8 are all being used for data transmission in Gigabit Ethernet data transmission Only 10Base T and 100Base TX can apply with POE 151 products A 2 RJ 45 cable pin assignment The standard RJ 45 receptacle conn
5. ce up to 100 meters e Auto detect of POE IEEE 802 3af equipment protect devices from being damaged by incorrect installation e Work with EIA568 category 5 4 pair cables for 10Base T or 100Base TX e EMI standards comply with FCC CE class B 1 4 Specification Model Ethernet Connector Ethernet Data rate Input voltage Number of device can be powered Ethernet cable LED indicator Dimension W x D x H EMI Standard Compliance 1 5 Product Outlook POE 151 2 x RJ 45 1 for data DC in 1 for Data out 10 100Mbps vary on Ethernet device attached DC 48V 0 4A TIA EIA 568 Category 5 5e cable 1 x power 1 x POE ready in use 73 X55 x 24 mm FCC Class B CE mark IEEE 802 3 Ethernet IEEE 802 3u Fast Ethernet IEEE 802 3af Power over Ethernet Apeay e yE Z08 1331 304 O y o 2 4 Li c Y D uMd s O 10d gt d Puy PLANG Power over Ethernet Injector 48V DC Ethernet 2 HARDWARE INSTALLATION This product provides two different running speeds 10Mbps 100Mbps in the same device and automatically distin guishes the speed of incoming connection This section describes the hardware features of POE 151 Before connecting any network device to the POE 151 read this chapter carefully 2 1 Prior Installation 2 1 1 Before star
6. ector There are 8 wires on a standard UTP STP cable and each wire is color coded The following shows the pin allocation and color of straight cable and crossover cable connection Straight Cable SIDE 1 SIDE 2 12734567 8 SIDET 4 whitelO0range 1 White Orange 2 Orange 2 Orange 3 White Green 3 White Green 4 Blue Blue 5 White Blue 5 White Blue 123465 6T 6 SIDE 2 6 amp Green Green T White Brown T White Brown 8 Brown 8 Brown Cross Over Cable SIDE 1 SIDE 2 1234567 8 SIDE 1 1 White Orange 1 White Green i 2 Orange 2 Green 3 White Green 3 White Orange a 4 Blue 4 Blue LL 6 White Blue 5 White Blue 1234567 8 SIDE 2 6 Green 6 Orange T White Brown T White Brown 8 Brown a Brown Figure A 1 Straight Through and Crossover Cable Please make sure your connected cables are with same pin assignment and color as above picture before deploying the cables into your network 2080 A31120 000
7. jector that provide DC 48V over Ethernet cables The POE 151 IEEE 802 3af Power over Ethernet Injector inserts DC Voltage into Cat 5 cable allowing the cable between the Injector POE 151 and Splitter POE 151S 5V 9V 12V to transfer data and power simultaneously The maximum distance be tween the Injector POE 151 and Splitter POE 151S 5V 9V 12V is 100 meters With POE 151 installed it is combines the Ethernet digital data with power over the twisted pair cables as an IEEE 802 3af Power over Ethernet Injector And the IEEE 802 3af Power over Ethernet splitter shall separate the digital data and the power into two outputs With IEEE 802 3af Power over Ethernet devices installed the system administrator only have to use a single RJ 45 Ethernet cable to carries both power and data to each devices Besides to connect through POE 151 and POE 151S 5V 9V 12V you could also have following benefit that cost saving easy for networking planning and higher reliability What s more upon any IEEE 802 3af devices installed the POE 151 or POE 151S 5V 9V 12V all can make the connection while migrating or splitting the power and the Ethernet digital packets such as connecting the POE 151 to an IEEE 802 3af complied devices AP or IP phone 1 3 Features Comply with IEEE 802 3af Power over Ethernet IEEE 802 3 802 3u 10 100Base TX Provide DC 48V power over RJ 45 Ethernet cable to device with Ethernet port LED indicators power input indication e Distan
8. nd found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Revision PLANET IEEE 802 3af Power over Ethernet Injector FOR MODEL POE 151 REVISION 1 0 MARCH 2006 Part No EM_POE151v1 2080 A31 120 000 TABLE OF CONTENTS 1 INTRODUCTION a da 4 SS A A A A ee 4 1 2 ABOUT THE POWER OVER ETHERNET INJECTOR ia lis 4 Lo FEATURE
9. pair 4 5 and pair 7 8 XA Notice 1 The POE 151 EEE 802 3af Power over Ethernet Injector will only work under Category 5 UTP STP cable with 4 pair Please refer to appendix A for detail information 2 Gigabit Ethernet device cannot be used to work with POE 151 since 1000Base T will use the 4 pair for data transmission refer to appendix A Co work with POE 151 the speed will change to 100Mbps follow the port s auto negotiation 3 The POE 151 and POE 151S can be installed in pair However the use of third party device is allowed if the device complied with IEEE 802 3af standard 2 1 2 POE 151 the Injector installation 1 Connect a standard network cable from Switch workstation to Ethernet port of POE 151 2 Connect the long cable that will be used to connect to the remote device to the port Ethernet DC The screen in Figure 1 appears 3 Connect the AC adapter to DC 48V of POE 151 The power LED will be steady on Switch POE 151 Figure 1 the Injector installation 2 1 3 POE 151 and POE 151S the IEEE 802 3af Injector and Splitter installation 1 Connect a standard network cable from Ethernet DC of POE 151 to Ethernet DC of POE 151S The POE LED of POE 151 POE 151S will light on continuance The screen in Figure 2 appears From POE 151 or IEEE 802 3af Power Supply equipment POE 151S RJ 45 Figure 2 Connection to POE 150S 2 Connect the UTP cable in the package from Ethernet
10. t up Before your installation please refer to the followings for your cabling 100Base TX The 10 100Base TX port comes with Auto Negotiation capability It automatically supports 100Base TX and 10Base T networks Users only need to plug a working network device into the 10 100Base TX ports then power on the POE 151 The port will automatically runs in 10Mbps 20Mbps 100Mbps or 200Mbps after the negotiation with the connected device Cabling The 10 100Base TX ports use RJ 45 sockets similar to phone jacks for connection of unshielded twisted pair cable UTP The IEEE 802 3u Fast Ethernet standard requires Category 5 UTP for 100Mbps 100Base TX 10Base T networks can use Cat 3 4 or 5 UTP see table below Maximum distance is 100meters 328 feet Cable Type Connector Cat 3 4 5 2 pair RJ 45 100Base TX Cat 5 UTP 2 pair RJ 45 Any Ethernet devices can connect to the POE 151 by using straight through wires The 10 100Mbps port is auto MDI MDI X can be used on straight through or crossover cable Before your installation it is recommended checking your network environment lf there is any issue for your install a networked device where is very difficult to find a power socket for your AC DC adapter POE 151 should provide you a way to provide DC power for this Ethernet device conveniently and easily The POE 151 comes with an AC DC adapter with DC 48V input and injects this DC power into the un used pin of the twisted pair cable
Download Pdf Manuals
Related Search