High Resolution Weatherproof IR Camera - Surveillance
Contents
1. SAMSUNG TECHWIN High Resolution Weatherproof IR Camera User Manual SC0 5083R um High Resolution Weatherproof IR Camera User Manual Copyright 2014 Samsung Techwin Co Ltd All rights reserved Trademark samsunGTEcHwWIN 4 is the registered logo of Samsung Techwin Co Ltd The name of this product is the registered trademark of Samsung Techwin Co Ltd Other trademarks mentioned in this manual are the registered trademark of their respective company Restriction Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this document shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document but no formal guarantee shall be provided Use of this document and the subsequent results shall be entirely on the user s own responsibility Samsung Techwin reserves the right to change the contents of this document without prior notice Warranty If the product does not operate properly in normal conditions please let us know Samsung Techwin will resolve the problem for free of charge The warranty period is 3 years However the followings are excluded f the system behaves abnormally because you run a program irrelevant to the system operation Deteriorated performance or natural worn out in proc2. The language communication and lens settings will remain the same 32 camera operation troubleshooting TROUBLESHOOTING If you have trouble operating your camera refer to the following table If the guidelines do not enable you to solve the problem contact an authorized technician Problems Troubleshooting Nothing appears on the screen e Check that the power cord and line connection between the camera and monitor are properly connected Check that you have properly connected BNC cable to the camera Check the type of lens e ONILOOHSATENOUL e The image on the screen is dim e 5 lens stained with dirt Clean your lens with soft clean cloth e Set the monitor or DVR to the proper condition e camera is exposed to very strong light change the camera position The image on the screen is dark e Adjust the contrast feature of the monitor or DVR e f you have an intermediate device set the 750 Hi z properly The camera is not working e Check that you have properly connected the camera to an properly and the surface of the appropriate power source camera is hot The DAY NIGHT menu does not e Check that AGC of EXPOSURE SETUP menu is OFF Work The INTELLIGENCE function does e Check that INTELLIGENCE of menu is not work Color is not correct e Check the setting of WHITE BAL SETUP menu The screen flickers continually e Ensure the camera is not pointing towards t
3. User BLC HLC WDR Wide Dynamic Range 120dB Contrast Enhancement Digital Noise Reduction SSDR Off On SSNR4 Off On 34 specifications SCO 5083RN SCO 5083RP Defog AUTO MANUAL OFF Purple Fringe Reduction Purple Fringe Reduction Off Low Middle High Digital Image Stabilization Off On Tampering Off On e Motion Detection Off On n Intelligent Video Fence Apear Disappear Counting Off On O Privacy Masking Off On 24 programmable zones with 4points polygonal masking a Gain Control Off Low Middle High White Bancs ATW Outdoor Indoor Manual AWC MERCURY lt 1 800K 10 500K Electronic Shutter Speed 1 sec 1 12 000 sec Digital Zoom Off On 1x 16x Reverse Off H Rev V Rev HV Rev Profile Basic Day amp Night Backlight ITS Indoor User Alarm 1 Out Communication Coaxial Control SPC 300 Compatible RS 485 Coax Pelco C Coaxitron Protocol RS 485 Samsung T Samsung E Pelco D Pelco P Panasonic Bosch Honeywell Vicon AD GE IR Distance 50m Environmental Operating Temperature Humidity 30 C 55 C 14 F 131 F Less than 90 RH X Start up should be done at above 10 C Ingress Protection IP66 Vandal Resistance IK10 Electrical Input Voltage Dual 24VAC 10 amp 12VDC 10 Power Consumption 9 5W Mechanical Color Material Dark Gray ALDC Dimension
4. X H 78x 231mm Weight 1 5Kg The specification for this product may change without prior notice for product improvement English_35 DIMENSION Unit mm SAMSUNG 36 specifications MEMO SALES NETWORK SAMSUNG TECHWIN CO LTD 6 Pangyo ro 319beon gil Bundang gu Seongnam si Gyeonggi do SEOUL 463 400 Rep of KOREA Tel 82 70 7147 8753 8764 Fax 82 31 8018 3740 www samsungsecurity com SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 100 Challenger Rd Suite 700 Ridgefield Park NJ 07660 2nd Floor No 5 The Heights Brooklands Weybridge Surrey KT13 ONY UK Toll Free 1 877 213 1222 Direct 1 201 325 6920 Tel 44 1932 82 6700 Fax 44 1932 82 6701 Fax 1 201 373 0124 www samsungsecurity co uk www samsung security com www samsungtechwin com www samsungsecurity com
5. and 10 500 OUTDOOR Use it in a color temperature range of 1 800K to 10 500K including Natrium Auto adjustment is made to optimize the camera color to the outdoor environment e INDOOR Select this when the color temperature is between 4 500K and 8 500 Automatically adjusts the camera color for optimization to the indoor environment MANUAL Select this to fine tune White Balance manually Set White p 1 RED GAIN Balance first by using the 9 BLUE GAIN ATW or AWC mode After that 3 RETURN button to MANUAL mode ain fine tune the White Balance and the Function Setup switch AWC SET To find the optimal luminance level for the current environment point the camera towards a sheet of white paper and press the Function Setup switch If the environment changes readjust it e Mercury This is an auto compensation function that optimizes camera colors for the environments such as mercury lamps 4 White Balance may not work properly under the following conditions In this case select the AWC mode Select this When the color temperature of environment surrounding the subject is out of the control range e g clear sky or sunset Q When the ambient illumination of the subject is dim f the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically the White Balance operation may become unstable 20 camera operation EXPOS
6. ATW ATW ATW OUTDOOR INDOOR BACKLIGHT OFF USER BLC OFF OFF SSNR4 ON ON ON ON DAY NIGHT AUTO AUTO AUTO AUTO AUTO 4 f you select the ITS the shutter will be set to 1 200 sec Noise can be detected at night SSDR Samsung Super Dynamic Range If an object has a large variance between bright and dark areas it will keep bright areas bright and make selected dark areas bright so that the overall brightness can be maintained 1 When the SETUP menu screen is displayed select SSDR by using the Function Setup switch so that the arrow indicates SSDR 2 Use the Function Setup Switch to SSDR SETUP change the SSDR level in the sub menu according to the contrast between bright and dark areas 8 CJ 8 CJ L1 L1 CI r1 CI CI am CO I I SSDRON SSDR OFF English 19 carnera operation White Bal White Balance Use the White Balance function to adjust the screen color 1 When the SETUP menu screen is displayed select White Bal by MAIN SETUP using the Function Setup switch so 1 PROFILE that the arrow indicates White Bal 2 SSDR 2 Select a desired mode using the gt 3 WHITE BAL Function Setup switch Select one of the following 6 modes as appropriate for your purpose ATW Select this when the color temperature is between 1 800K
7. exposure and preserve much of the on screen details when the camera aims a strong light source LEVEL Adjusts the brightness 3 MASK COLOR 4 MASK TONE 5 TOP 6 BOTTOM 7 LEFT level of a monitoring area LIMIT Enable to change the operating condition MASK COLOR TONE Change the color brightness of the masking area Black Red Blue Cyan Magenta TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced RETURN Return to the MAIN SETUP menu If the white balance menu is set to manual then HLC performance can be limited If you use the defog and HLC functions at the same time saturation can occur in a bright environment Because there can be a difference in the effectiveness of HLC according to the amount of light area in the screen optimize the installation angle for the best HLC performance When dark the HLC is only activated when a bright light exceeding a specifi c size In NIGHT ONLY mode The HLC is not activated in day light or when bright light is not present at night In NIGHT ONLY mode 8 RIGHT 9 RETURN I 22 camera operation e WDR When there are both bright and dark areas at the same time this mode makes both areas distinctive LEVEL Select one from low middle high to adjust the brightness of the WDR setup WDR SETUP VHIWVO WDR ON RETURN Return to the MAIN SETUP menu 2 n WDR mode the max
8. gt m e DET SIZE Selects an object size to detect on the screen O e DET AREA Set the areas of E motion detection MOTION DETECT AREA 5 SEL AREA Select from four MODE 5 areas that users Want 3 SENSITMTY MODE Determine whether to 4 TOP use the selected area 5 BOTTOM SENSITIVITY Set the 6 LEFT sensitivity of 7 RIGHT the motion 8 RETURN detection When you adjust the higher level the more sensitive TOP BOTTOM LEFT RIGHT Area location can be adjusted RETURN Return to the MOTION DET menu NON DET AREA Specify a detection exception area to mask Select a mask area number and specify the size and position SEL AREA You can select up to 4 areas MODE Determines whether to use the area selected in the AREA TOP BOTTOM LEFT RIGHT Adjust the size and position of the selected area RETURN Return to the MOTION DET menu INDICATOR If an object moves in a pattern set by the user it will be displayed on the screen as a box e ALARM OUT When object movement is detected the detection signal will be outputted EXTERNAL Send signals through external terminals OSD Display signals on the screen RETURN Return to the MOTION DET menu e RETURN Return to the VIDEO ANALYTICS menu English 29 camera operation INTELLIGENCE Set the intelligent INTELLIGENCE video detection gt 1 SENSITIVITY pong rang function 2 DET SE e SENSITIVITY Set the
9. object s brightness or color is similar to that of the background f there is little movement near the screen edge If multiple movements keeps occurring randomly such as scene switching or sudden light changes If an object fixed in the same location keeps moving Moving away from the camera or approaching the camera Little location change on the screen If a moving object approaches the camera If random objects obstruct the view of each other If more than one objects merge or one object divides into multiple objects If an object moves too fast the same object should have overlapping areas between the consecutive frames I there are reflections blurs shadows created by a strong light such as direct sunlight lights and headlights Severe snow rain and wind Sunset or sunrise If the size is greater than the max size or smaller than the min size motion is not detected To avoid false detection caused by noises set the max min detection size suitable for the installation environment But the same movement in the same location can cause a different detection size So include margins when you set the min max detection size EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose e SAVE Save the current settings and exit the MAIN SETUP menu NOT SAVE Do not save the current settings and exit the MAIN SETUP menu e RESET Revert camera to factory settings
10. 20s 30s 40s 60s If you set the AGC mode to off on the exposure menu you cannot switch the day night mode to auto When a bright light source is in the screen or there are frequent brightness changes if you use the auto night day mode and set the switching time to short 3 5 sec a hunting can be caused In this situation it is recommended to use the default setting 30 sec 4 RETURN 26 camera operation EXTERN Ground to the grounding terminal to allow automatic switching between COLOR and B W Black White COLOR The picture is always displayed in color B W The picture is always displayed in black and white BURST MODE Activate or deactivate the burst mode to maintain or remove the color signal IR When IR LED is turned on in B W the objects can be clearly identified due to the function that decreases screen saturation of objects within a short distance e DEFOG You can use the defog mode to allow the camera to automatically detect the fog density of the screen and display a clear image despite smog fog or general poor visibility If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates VHIWVO DEFOG MANUAL SETUP gt 1 LEVEL Select a desired mode using the Function Setup switch AUTO Adjust the level automatically MANUAL Depending on the defog level set by the user adjust the clarity of i
11. E 5 PROTOCOL 6 COAX o 5 gt d 2 CAM ID Determines the camera s identification number between O and 255 BAUD RATE You can select 2400 4800 9600 19200 38400 57600 bps UART MODE You can select NONE EVEN or ODD for the parity bits RET PKT Specify whether to return the same command to the controlling device when a control command is delivered to the camera COAX You can select whether to use COAX communication RETURN Return to the SPECIAL menu MAGE ADJ IMAGE SETUP If the SPECIAL menu screen is gt 1 GAMMA displayed use the Function Setup 2 PED LEVEL Switch so that the arrow indicates 3 COLOR IMAGE ADJ 4 H REV Select a desired mode using the 5 V REV Function Setup switch 6 D 200M GAMMA The setting range is 0 2 7 SHARPNESS 1 0 The closer to 1 0 the setting is the darker it gets gt 0 20 0 25 0 30 0 35 0 40 0 45 0 50 0 55 0 60 0 65 0 70 0 75 0 80 0 85 0 90 0 95 1 0 PED LEVEL The setting range is 1 100 The closer to 100 the setting is the higher the PED level gets COLOR GAIN The setting range is 1 100 The smaller the setting value is the smaller the color gain gets and the more color blind it gets H REV Hip an image horizontally 8 PFR 9 RETURN English 25 camera operation V REV Flip an image vertically D ZOOM You can use a digital zoom of x1 x16 SHARPNESS Select a mode to adjus
12. R OSD KEY UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT English_15 connection RS 485 communications Using RS 485 communication the camera menu can be accessed using Samsung Techwin s System Controller or the DVR e for accessing the camera from a computer Use a RS 485 converter to connect the camera s control port with the computer s serial cable Ex Serial port COM1 of computer gt Serial Cable gt RS 485 Converter gt Camera s RS 485 control port e for accessing the camera from a Dw or the System controller connect the camera s RS 485 and RS 485 terminals to the RS 485 control board s terminals of desired device with a RS 485 cable Control ports of RS 485 Controller RS 485 ports of the camera CONNECTION TERMINAL 4854 C CONNECTION TERMINAL 485 Default RS 485 communication settings Item CAM ID BAUD RATE UART MODE RET PKT Default ENABLE Video Cable The camera s video output port is connected to the monitor with a BNC coaxial cable shown below If the distance between the camera and the monitor exceeds the recommended maximum please use an auxiliary video amp Distance 300 3C2V RG 59 U 450m 5C2V RG 6 U 600m 7C2V RG 11 U t is recommended that pure copper coax cable is used and not copper coated steel as this will cause issues with the communication over the coaxial cable To ensur
13. URE 1 When the SETUP menu screen is displayed select EXPOSURE by using the Function Setup switch so that the arrow indicates EXPOSURE 2 Select a desired mode using the Function Setup switch EXPOSURE SETUP pd BRIGHTNESS Adjusts the video HBRGHINES brightness eie uu 3 SHUTTER 3 e LENS Using this function you 4 can control the screen 5 SSNR4 m brightness 6 RETURN gt DC Select Auto Iris Lens e IRIS SPEED DC Adjusts the Iris control speed of the DC lens If the control speed is too slow or fast please use this menu to adjust the speed FOCUS ADJ DO To correctly adjust the focus of LENS activate the focus setup mode located at the bottom of each lens menu Manual The shutter does not automatically move but is fixed to the maximal degree in this mode e SHUTTER You can select the shutter MIN 1 1 12000 MAX 1 60 1 12000 NTSC 1 50 1 12000 PAL AFLK Select this when you experience picture flicker this happen when there is a clash with the installed lighting frequency 4 The greater the shutter value the brighter the screen is but the more the residual images of objects there are f the min shutter value is large it can cause noise spots and white areas but still operate normally f you do not use the AGC mode on the exposure menu it cannot be set above 1 60 1 50 sec Depending on the setting range of the minimal max
14. arked Class 2 and rated from 24 Vac 50 60Hz min 0 8A or 12 Vac min 0 8A Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus Samsung Techwin cares for the environment at all product manufacturing C stages to preserve the environment and is taking a number of steps to provide customers with more environment friendly products The Eco mark represents eco Samsung Techwin s will to create environment friendly products and indicates compl that the product satisfies the EU RoHS Directive English 7 NOILVWHOANI AL34VS contents INTRODUCTION CONNECTION CAMERA OPERATION TROUBLESHOOTING SPECIFICATIONS 8 contents 17 17 33 34 36 Features Components and Accessories Components names and Functions Adjust the lens s zoom and focus Connecting to Monitor Connecting to Power Using Communications Menu Configuration Menu Setup Troubleshooting Specifications Dimension introduction FEATURES High Resolution Use of a 1 3mega pixel CMOS device provides clear pictures with a horizontal resolution of 1000TVL e Excellent Sensitivity The built in high sensitivity COLOR CMOS produces a clear image Color 0 05Lux F1 4 0 001Lux 1sec F1 4 5OIRE 0 02Lux F1 4 0 0006Lux 1sec F1 4 SOIRE B W OLux IR LED On NOILONGOULNI e Intelligence Withou
15. d 9 area RETURN Return to the VIRTUAL FENCE menu COUNT Displays how many times a subject passes over the fence on the screen RETURN Return to the INTELLIGENCE menu e APPEAR Detects an object that emerges or disappears from the screen or stays onscreen without movement e INDICATOR Outlines an object on the screen in a box when its movement matches a custom Motion Type 2 In the following cases the appear indicator may malfunction When multiple movements occur randomly When a fixed object keeps moving in the same location When a new object covers an object with changes e ALARM OUT When object movement is detected the detection signal will be outputted EXTERNAL Send signals through external terminals OSD Display signals on the screen RETURN Return to the INTELLIGENCE menu e RETURN Return to the VIDEO ANALYTICS menu RETURN Return to the SPECIAL menu e RETURN Return to the MAIN menu English 31 camera operation Before use set the max min movement size within the range Depending on the shape of an object there can be errors in size detection From the top of the screen a max of sixteen objects can be expressed f the camera shoots an object a short distance away the video analysis function can be degraded n the following cases motion detection or video analysis event performance can be degraded or malfunctions can occur If an
16. e picture quality only single channel video output connector can be used while camera connected to other video equipments 16 connection camera operation MENU CONFIGURATION MAIN SETUP BASIC DAY NIGHT BACKLIGHT e 15 INDOOR USER SSDR e OFF e ATW OUTDOOR INDOOR MANUAL AWC SET MERCURY BRIGHTNESS LENS SHUTTER Bana AGC SSNR4 RETURN e OFF USER BLC e uc BACKLIGHT e Wor DISPLAY COMM ADJ IMAGE ADJ SPECIAL DAY NIGHT DEFOG PRIVACY 05 VIDEO ANALYTICS RETURN EXIT SAVE NOT SAVE RESET MENU SETUP For function setting you can use the function setting switch inside the dome cover Function Setup switch English 17 VHINWVO carnera operation MAIN SETUP Select the functio 1 PROFILE Change the status using the Function 2 SSDR using the Function Setup switch 3 WHITE BAL Setup switch 4 EXPOSURE 5 BACKLIGHT 6 SPECIAL 7 EXIT 1 Press the Function Setup switch Main SETUP menu is displayed on the monitor screen 2 Select a desired function using the Function Setup switch e Place the cursor over a desired item 3 Set up a selected item by using the Function Setup switch 4 To finish the setting select EXIT and press the Function Setup switch item with the icon also has sub menus To select a sub menu select an item with the icon and press the Function S
17. e with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus NO c c rn 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus 13 Unplug this apparatus when a card is used Use caution when moving the cart apparatus combination to avoid injury from tip over 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 This product is intended to be supplied by a Listed Power Supply Unit m
18. en tested and found to comply with the limits for a Class A digital device pursuant to part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense IC Compliance Notice This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations of ICES 003 Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact ei
19. er from the 2 camera by turning the cover counterclockwise To adjust the zoom amp focus loosen the individual levers before tightening them again To ensure the weatherproof integrity is maintained Before installation the front cover it s necessary to push tight first and then turn it clockwise to locking indication English_11 Introduction Back Function jack GREEN 485 Signal port for RS 485 communication YELLOW 485 Signal port for RS 485 communication BLUE ALARM OUT Output port that signals when a motion is detected GRAY EXT D N External signal input port for Day Night mode setup BLACK GND Earth grounding port for external signal Q Video output jack Video signals are output through this port Connect this port to the Video IN port of a monitor Power input terminal Connect the power as specified for each model here 12 introduction ADJUST THE LENS S ZOOM AND FOCUS Remove the sunshield from the camera Remove the front cover from the camera by turning it counterclockwise Unlock the Zoom or Focus lever before adjusting the lens A N Adjust the zoom amp focus by moving the lever counterclockwise for NEAR amp WIDE and clockwise for TELE amp FAR position 5 After adjustment tighten the zoom or focus levers taking care not to adjust the zoom focus position NOILONGOULNI 6 Please close and tighten the front cover T Replace
20. er supply or replacing battery may cause explosion fire electric shock or damage to the product 3 Do not connect multiple cameras to a single adapter Exceeding the capacity may cause abnormal heat generation or fire 4 Securely plug the power cord into the power receptacle Insecure connection may cause fire 5 When installing the camera fasten it securely and firmly The fall of camera may cause personal injury 4 safety information Do not place conductive objects e g screwdrivers coins metal parts etc or containers filled with water on top of the camera Doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way samsung is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 1 9 Do not drop objects on the product or apply strong shock to it Keep away fro
21. ess of time Design and specifications are subject to change without prior notice Before operating the camera confirm the camera model and correct input power voltage To help you understand this manual thoroughly we ll introduce our model description ill SC0 5083R SERIES e NTSC MODEL e PAL MODEL SC0 5083RN SC0 5083RP i MODEL DESCRIPTION SCO 5083RX mi SIGNAL SYSTEM e SIGNAL SYSTEM NTSC MODEL P PAL MODEL Safety information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING To prevent damage which may result in fire or electric shock hazard do not expose this appliance to rain or moisture e To prevent injury this apparatus must be securely attached to the floor wall in accordance with the installation instructions WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the pow
22. etup switch An item with the icon is unavailable due to function settings PROFILE 1 When the SETUP menu screen is displayed select PROFILE by using the Function Setup switch so that the arrow indicates PROFILE 2 Select a desired mode using the Function Setup switch according to MAIN SETUP the picture display you want 1 PROFILE BASIC The most j dn The most common envi ronment is set to meet 3 WHITE BAL e DAY NIGHT It will be set 4 EXPOSURE automatically so it 5 BACKLIGHT optimizes to the day 6 SPECIAL or night conditions 7 EXIT respectively BACKLIGHT It will be set automatically so you can distinguish the object from the background in a severe backlighting scene ITS It will be set automatically so you can easily check the traffic conditions 18 camera operation INDOOR It wil be set automatically to help you take a picture in a regular indoor lighting condition USER Automatically configures the camera to your custom settings 1 Select USER for Simple Setup mode 2 Configure the menu options to your USER settings 3 The settings are automatically saved as USER mode 4 Profile user mode don t initialize when menu resets 3 In the PROFILE menu you can confi gure the following camera settings at once BASIC DAY NIGHT BACKLIGHT ITS INDOOR USER SHUTTER 1 5 1 12000 1 5 1 12000 1 5 1 12000 1 200 1 12000 A FLK AGC HIGH HIGH HIGH HIGH HIGH WHITE BAL
23. he sun When coaxial communication is not e Make sure that the camera and monitor are installed within available the recommended distance e Use the video amplifier equivalent to coaxitron if the recommended installation distance is exceeded English 33 specifications SPECIFICATIONS SCO 5083RP Video Imaging Device 1 3 1 3M CMOS Total Pixels 1312 H x 1069 V Effective Pixels 1305 H x 1049 V Scanning System Progressive Scan Synchronization Internal Frequency H 15 734KHZ V 59 94Hz 15 625KHz V 50Hz Horizontal Resolution Color 1000 TVL B W 1000 TVL Min Illumination Color 0 05Lux F1 4 50IRE 0 001Lux 1sec F1 4 SOIRE 0 02Lux F1 4 30IRE 0 0006Lux 1sec F1 4 B W OLux IR LED On S N Ratio 52dB AGC off Weight on Video Output CVBS 1 0 Vp p 750 composite Lens Type Focal Length Zoom Ratio Max Aperture Ratio Angular Field of View 3 10mm F1 4 82 0 Wide 26 5 Tele V 59 7 Wide 19 9 Tele Min Object Distance 0 5m Focus Control Manual Lens Type DC Auto Iris Mount Type Board Type Operational On Screen Display English Chinese Korean Japanese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese Camera Title Off On Displayed 15 characters Day amp Night Auto ICR External Color B W Backlight Compensation Off
24. imal shutter the screen exposure can become saturated AGC OFF LOW MIDDLE HIGH The higher the gain level the brighter the screen but the greater the noise SSNR4 This function reduces the background noise in a low luminance environment OFF Deactivates SSNR4 Noise is not reduced ON Activates SSNR4 so that noise is reduced 4 When adjusting the noise reduction level of the SSNR4 mode remember that the higher the level set the more the noise level will be reduced but that after image may also occur English 21 carnera operation BACKLIGHT The camera uses our own W7 chips that are designed to clearly display the object and the background despite severe reverse light 1 When the SETUP menu screen is displayed select BACKLIGHT by using the Function Setup switch so that the arrow indicates BACKLIGHT 2 Select a desired mode using the Function Setup switch depending on the camera purpose e USERBLC Enables a user to select a desired area on a picture and view that area more clearly LEVEL Adjusts the brightness level of a monitoring area TOP BOTTOM LEFT RIGHT Adjust the area to be enhanced RETURN Return to the MAIN SETUP menu HLC High Light Compensation This function masks the strong light to minimize white out due to over BLC SETUP 1 LEVEL 2 TOP 3 BOTTOM 4 LEFT 5 RIGHT 6 RETURN HLC SETUP gt 1 LEVEL 2 LIMIT MIDDLE NIGHT ONLY
25. itch ANALYTICS 1 TAMPERING TAMPERING If the screen view is obstructed or the TAMPERING camera location gt 1 SENSITIVITY is changed 2 ALARM OUT tampering 3 RETURN 4 detection you can issue an event signal by setting it SENSITIVITY Set the sensitivity to tampering detection ALARM OUT Outputting of detection signals can be set EXTERNAL Send signals through external terminals OSD Display signals on the screen RETURN Return to the TAMPERING menu RETURN Return to the VIDEO ANALYTICS menu 2 n the following cases the initially set tampering detection function can malfunction monitoring environment with a simple background or an environment with low light level or at night the detection performance can deteriorate Sudden changes in the lighting and severe camera shaking can be wrongly detected as tampering Immediately after tampering the camera tampering detection can take up to a max of five seconds f camera tampering is detected after some time five sec stabilization will be done before restarting During stabilization there is no detection 28 camera operation MOTION This product generates signals each time an object gt 1 DET SE lt 1 movement is detected 2 DET AREA in the four areas of 3 NON DET AREA 4 the screen so efficient 4 INDICATOR MOTION DET monitoring can be 5 ALARM OUT 4 pa achieved 6 RETURN
26. lect the position d to display the title on the screen by using the UA Function Setup switch and press the Function 4t Setup switch When the position is determined ois aoe pale asc erae select END and press the Function Setup switch to return to the DISPLAY menu 2 When the CAM TITLE menu is OFF no title will be displayed on the monitor screen even if you enter one and Numbers are available in this mode f you move the cursor to CLR and press the Function Setup switch all the letters are deleted To edit a letter change the cursor to the bottom left arrow and press the Function Setup switch Move the cursor over the letter to be edited move the cursor to the letter to be inserted and then press the Function Setup switch 24 camera operation DISP ID Display camera ID on top left corner of the screen FONT COLOR You can change the OSD font color White Yellow Green Red Blue LANGUAGE You can select the menu language according to your requirements RETURN Return to the SPECIAL menu e COMM ADJ Communication Adjust SAMSUNG 7 RETURN T Samsung E Pelco D Pelco P Panasonic Bosch Honeywell Vicon AD GE ment This function sets up the camera COMM SETUP pd communication status when controlling the 1 PROTOCOL SAMSUNG T gt camera through an external control device m 1 D PROTOCOL Select the 4 UART MODE 8 N 1 a communication 5 RET PKT ENABL
27. m a location subject to excessive vibrationor magnetic interference Do not install in a location subject to high temperature over 55 C low temperature below 30 or high humidity Doing so may cause fire or electric shock If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it Remove the power plug from the outlet when then there is a lightning Neglecting to do so may cause fire or damage to the product Keep out of direct sunlight and heat radiation sources It may cause fire Install it in a place with good ventilation Avoid aiming the camera directly towards extremely bright objects such as sun as this may damage the CMOS image sensor Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus The Mains plug is used as a disconnect device and shall stay readily operable at any time 10 Do not expose the camera to radioactivity Radioactivity exposure may damage the CMOS English 5 NOILVWHOANI AL34VS Safety information FCC Statement This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation CAUTION This equipment has be
28. mage LOW MIDDLE HIGH OFF Released state 2 f the defog mode is set to Auto and if the amount of fog is reduced the function level will be also reduced If you want to maintain the same level of defogging set it to Manual If there is little fog and the manual fog level is high the screen contrast can get high PRIVACY Mask an area you want to hide on the screen PRIVACY AREA SETUP gt 1 AREA the SPECIAL menu screen is gt MODE displayed use the Function Setup 3 MASK COLOR Switen SO that the arrow indicates 4 TRANSPARENCY PRIVACY 5 SELPOS Select a desired mode using the 6 X POS Function Setup switch 7 Y POS AREA You can select up to 24 ETE PRIVACY areas MODE Determines whether to use the area selected in the AREA English 27 camera operation MASK COLOR Determine area color You can select Green Red Blue Black White Gray TRANSPARENCY Adds or removes transparency from the masking area SEL POS X POS Y POS Adjust the size and position of the selected area RETURN Return to the SPECIAL menu DIS Digital Image Stabilizer This function mitigates any picture movement due to external factors such as wind e VIDEO ANALYTICS If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates 2 MOTION VIDEO ANALYTICS 3 INTELLIGENCE Select a desired mode using the 4 RETURN Function Setup sw
29. min shutter value is set to 1 2 to 1 480 n WDR mode there can be noise between a bright and dark area Depending on light conditions unnatural changes or symptoms can occur on the screen so deactivate the user mode English 23 carnera operation SPECIAL 1 When the SETUP menu screen is displayed select SPECIAL by using the Function Setup switch so that the arrow indicates SPECIAL 2 Select a desired mode using the Function Setup switch SPECIAL SETUP gt 1 DISPLAY e DISPLAY 2 COMM ADJ lt 1 If the SPECIAL menu screen is A ee displayed use the Function Setup see 5 DEFOG switch so that the arrow indicates 6 PRIVACY DISPLAY a DS Select a desired mode using the 8 VIDEO ANALYTICS Function Setup switch 9 RETURN CAM TITLE If the DISPLAY menu screen CAMERA TITLE SETUP is displayed use the Function ABCDEFGHIJKLM Setup switch so that the arrow NOPQRSTUVWXYZ Md abcdefghijklm indicates CAM TITLE nopqrstuvwxyz Set it to ON by using the 0123456789 Function Setup switch Press the Function Setup switch Use the Function Setup switch to move to a desired letter and select the letter by pressing the Function Setup switch Repeat this to enter multiple letters You can enter up to 15 letters Enter a title move the cursor to POS and LR POS END press the Function Setup switch The entered FRONT DOOR title appears on the screen Se
30. sensitivity FENCE 4 of the motion 4 APPEAR detection When 5 INDICATOR you adjust the 6 ALARM OUT higher level the 7 RETURN _ more sensitive e DET SIZE Selects an object size to detect on the screen e FENCE VIRTUAL FENCE SEL FENCE You can select gt 1 SELFENCE up to 4 FENCE 2 MODE MODE Determines whether 3 TYPE to use the fence 4 POSITION selected in the 5 COUNT FENCE 6 RETURN Two types line and area of fences are available POSITION Defines the position and detection direction of a line or fenced area 1 LINE FENCE SEL POS Selects a LINE FENCE position from gt 1 SELPOS POS1 POS 2 XPOS XPOS Y POS 3 YPOS Adjust the size and position 4 DIRECTION of the selected line fence RETURN DIRECTION RIGHT Detects objects moving left to right on the fence line LEFT Detects objects moving right to left on the fence line RIGHT LEFT Detects all objects moving crosswise on the fence line RETURN Return to the VIRTUAL FENCE menu 30 camera operation 2 AREA FENCE SEL POS Selects a gt 1 SELPOS position from 2 XPOS XPOS Y POS Adjust 4 DIRECTION the size and position of the 5 RETURN selected area fence 9 DIRECTION e ENTER Detects objects entering the fenced area n EXIT Detects objects exiting the fenced area ENTER EXIT Detects all objects entering and exiting the fence
31. t Compensation REVERSE D ZOOM SHARPNESS and PRIVACY functions are provided e Communication RS 485 Coaxial communication methods are supported Coaxial Communications Pelco Coaxitron RS 485 Samsung T Samsung E Pelco D Pelco P Panasonic Bosch Honeywell Vicon AD GE e OSD The camera s OSD is complimented by 17 languages English Chinese Korean Japanese German Italian French Spanish Russian Czech Polish Romanian Serbian Swedish Danish Turkish Portuguese COMPONENTS AND ACCESSORIES Check if the following items are included in the product package High Resolution Weatherproof IR Camera Quick Mona pa d d Wa ty 1 SCO 5083R Screws Sunshield Template Wrench Knob Sunshield Video Output Cable 10_ introduction COMPONENT NAMES AND FUNCTIONS Front NOILONGOULNI Camera Sunshield Knob Sunshield Fixing the sunshield onto the camera Focus lever Set focus of lens by turn the focus lever Zoom lever Set zoom magnification of lens by turn the zoom lever Front cover Q Function Setup Switch Display the menu on the screen and move the cursor to four directions to confirm status or after changing a selected item video Output Terminal to Monitor Used for monitoring of video output When camera installation 777 When you adjust to the ZOOM amp FOCUS of the lens Please remove the front cov
32. t an external sensor you can use this product to detect motion and generate alarms and thus more efficient monitoring can be achieved e SSNR4 Samsung Super Noise Reduction Function The high performance W7 effectively removes low light gain noise and afterimage to provide clear images even in dark environments e Day amp Night This camera has a function that automatically selects the mode that is appropriate for daytime or night time conditions The COLOR mode operates in daytime condi tions to provide optimum colors and B W mode operates in night time conditions to enhance the definition of the image e SSDR Samsung Super Dynamic Range For images with high contrast between bright and dark areas from difficult lighting conditions such as backlighting this camera selectively illuminates darker areas while retaining the same light level for brighter areas to even out the overall brightness e PROFILE You can set a mode according to the camera installation conditions BASIC DAY NIGHT BACKLIGHT ITS INDOOR USER e WDR By adopting a proprietary W7 chip the camera delivers clear high quality pictures even in backlight by increasing exposure in dark areas while decreasing it in bright areas a corrected image with clear details results DIS Digital Image Stabilizer The DIS function compensates for any camera movement to produce more stable pictures English 9 introduction e Miscellaneous Functions HLC High Ligh
33. t the thickness of an image s sharpness Increase or decrease the level of each mode to adjust the level of sharpness Depending on the image adjust it to an appropriate value OFF LOW MIDDLE HIGH PFR Purple fringe can be reduced RETURN Return to the SPECIAL menu 2 When the V REV or H REV mode is enabled the text on the screen does not flip Ifyou increase the SHARPNESS level too high the picture may become distorted or noise may appear When you use the function if there is an object near the strong light the color can be missing e DAY NIGHT You can display pictures in color or in black and white If the SPECIAL menu screen is displayed use the Function Setup switch so that the arrow indicates DAY NIGHT Select a desired mode using the Function Setup switch according to the picture display you want AUTO The mode is switched to Color in a normal SENA 1 BURST MODE environment but 2 DURATION switches to B W mode 3 DWELL TIME when ambient illumination is low To set up the switching time for AUTO mode press the Function Setup switch You can turn on or off the burst signal on B W mode BURST MODE Activate or deactivate the burst mode to maintain or remove the color signal DURATION This function is used to select the brightness of light where switching occurs DWELL TIME You can select day night switching delay time from 3s 58 78 10s 15s
34. the sunshield SAMSUNG FRONT COVER ZOOM LEVER FOCUS LEVER FAR NEAR 4 f the front cover is cross threaded or not correctly tightened the camera housing will not be weatherproof English_13 connection CONNECTING TO MONITOR Please connect the Video output jack located on the back of the camera to the monitor Camera Monitor e As the connecting method varies with the instruments refer to the manual supplied with the instrument e Only connect the cable when the power is turned off CONNECTING TO POWER You can connect power as shown in the following figure 14 connection When the resistance value of copper wire is at 20 C 68 F Copper wire size AWG 24 0 22mm 22 0 33mm 20 0 52mm 18 0 83mm Resistance value Q m 0 078 0 050 0 030 0 018 Voltage Drop V m 0 028 0 018 0 011 0 006 As shown in the table above voltage decreases as the wire gets longer Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera Standard voltage for camera operation DC 12V 10 AC 24V 10 There may be some deviation in voltage drop depending on the type of wire and the manufacturer NOILO3NNOO 2 Be sure to connect power only after all the installation is complete USING COMMUNICATIONS Coaxial Communications System 050 Control method CAMERA CONTROLLER SET MENU ENTE
35. ther the retailer where they purchased this product or their local government Office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system 6 safety information mportant safety instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordanc
Download Pdf Manuals
Related Search