Home

PRintX-FPR

1. 3 2 General characteristics e Allow finger rotation 18 e Allow displacement 5 mm e False acceptance ratio up to 0 001 e Equal error rate 0 001 e Verification name lt 1 s e Enrolment time lt 5 s Synel Industries Ltd 4 PRint FPR Unit Layout 4 Unit Layout i pe a LED Operation Status Indicator SSS 1 Fingerprint sensor 5 Installation 5 1 General e The unit is installed at sensitive locations to assess user entrance rights to secure areas e The unit works together with other units to increase security of the sensi tive locations where it is installed e The back panel of the unit serves as an installation template to mark the location of the screws Synel Industries Ltd 5 PRint FPR Installation 5 2 Finding the best location for the unit Follow the guidelines below to find the best place to mount the terminal Place the terminal by an easily accessible power outlet Do not place the communication cable near a source of electromagnetic radiation or radio interference such as power lines large machinery etc Do not place terminal where exposed to extreme hat or cold water steam violent vibrations or strong electromagnetic radiation including high voltage power lines and electrical equipment The installation location selected should be as far as possible from sources of electrical reference such as power equipment computers motors pumps etc Maintain at least
2. PRint FP PRintX FPR User Manual PRint FPR PRint FPR 08 28 08 Part no 650445 PRint FPR 222 01 This document has been prepared for PRint FPR device All rights reserved Repro duction or use without express permission of editorial or pictorial content in any manner is prohibited No patent liability is assumed with respect to the use of the information contained herein While every precaution has been taken in the prepara tion of this manual Synel Industries Ltd assumes no responsibility for errors or omissions Neither is any liability assumed for damages resulting from the use of the information contained herein DCM and SY are trademarks of Synel Industries Ltd All trade names referenced herein are either trademarks or registered trademarks of their respective companies Synel Industries Ltd 2 PRint FPR Introduction 1 Introduction The PRint FPR biometric controllers with Optical sensor or Capacity sensor are part of the Synel series of access control portals PRint FPR units combine fingerprint verification and identification PRint FPR units work together with other units according to the security level required for the specific location of the unit Working in conjunction with other units defining parameters and maximizing security using passwords defined by the user 1 1 Operation modes e Enroll New fingerprint templates can be enrolled at the unit and stored for future recognition e
3. Verification The verification mode of access control requires a card code combination The template is stored with reference to a card code Up to 4000 card code combinations and templates are stored When an employee swipes a card or keys in a code the unit checks whether the card code number exists if it does the unit also checks the template assigned to that number e Identification The identification mode does not require a card code combination Up to 9090 fingerprint templates are stored in the termi nal s memory When an employee places a finger on the sensor the FP fingerprint unit polls all existing templates for a match and confirms or rejects access accordingly e Erase Deletes one or all stored templates from the memory 2 Package e PRintX FPR unit e PRintX FPR mounting panel e RJ 11 Connection box with 5V power input e RJ 45 Connection box e A mounting set that includes the following 2 screws for mounting the mounting panel 1 screw for securing the unit to mounting panel Wall anchors 2 Brick 2 Plaster e Mounting template e User manual on CD Synel Industries Ltd 3 PRint FPR Specifications Recommended PRintX 40 Power supply adaptor 12 to 15 Vdc max 880 mA 3 Specifications 3 1 Technical Specifications e Dimensions 15 5 x 7 x 6 1 cm e Weight 350g e Operating temperature 10 to 50 C e Relative humidity 95 e Power supply 5Vdc 20 5A e Output relay rating 24 V 3 A
4. a one meter distance from computer displays Keep the cable by at least 30 cm away from any other cable Use a power adaptor dedicated to the proximity unit Make sure the adapter carries a safety recognition marking such as UL CSA or CE Use a linear power supplier and not a switching power supplier which generates an electro magnetic field that shortens the reading range It is advisable to connect an independent power supplier to the reader Make sure there are no metallic materials surrounding the unit When mounting on a drywall gypsum wall make sure that there are no rear metallic reinforcements to the wall Make sure that it is safe to drill into the wall at the desired location The terminal should be mounted at employee eye height Consider accessibility of handicap users if necessary The standard recommended height is 140cm 7 Place the reader so that the user will be fully facing it when swiping the badge since this is the best swiping position Caution The terminal contains computer components Thus should not Synel Industries Ltd 6 PRint FPR Installation 5 3 be mounted where it will be exposed to extreme heat or cold water steam violent vibrations high electromagnetic radiation including high voltage power lines and electrical equipment Mounting the unit Select a location for the terminal using the above guidelines for finding the best location Hold the mounting template to the wall and
5. ce a finger for sampling purposes while the Enrolment process is on Orange Waiting for fingerprint validation while performing veri fication Green Successful operation Red Failure 6 2 Access Control using PRint FPR Place the user finger on the PRintX sensor A fingerprint recognised as matching a fingerprint template stored in the unit allows access activates door relay Ne An un recognised fingerprint denies access and initiates a buzzer sound door relay is not activated 6 2 1 FPU operation Instructions and Best practices 1 Do not use your thumb to enrol Place the higher joint of your finger on the ridge lock and lower your finger onto the sensor surface make sure all other fingers are held straight to avoid creating an angle between the enrolled finger and the sensor surface incorrect positioning 3 Touch the sensor s plastic casing black in order to discharge static electricity Keep your finger steady Synel Industries Ltd 9 PRint FPR Maintaining good working order 4 Press your finger gently onto the panel avoid excessive pressure as it will blur the print 5 Make sure your finger is touching the sensor s drive ring 6 Use the same finger for enrolment as well as for verification 7 If your finger is extremely dry touch your forehead or the side of your nose before placing it on the sensor 8 Do not use a wet moist finger for scanning 7 Maintaining go
6. mark the places to drill holes for the screws and cables Drill the holes for the connection cable and screws with 6mm drill bit Inset the screw anchors for either plaster or concrete Connect communication cable from external components to communication box as needed Mount the panel to the wall and adjust it so that it is straight and the cable is in place Slide the unit downward onto to the mounting panel The hinges at the side of the panel 1 should slide into the track of the mounting panel 2 Synel Industries Ltd 7 PRint FPR Operation 8 Once the unit is in place you can screw the security screw connecting between the panel and the unit at the top of the unit and panel 6 Operation The PRintX P reader allows the following basic operations Enrolment scanning a fingerprint determining the quality of the fingerprint scan and storing a good template as a reference Synel Industries Ltd 8 PRint FPR Operation Identification compares the currently scanned fingerprint to fingerprint templates stored in the database Verification proofing of the currently scanned fingerprint against stored fingerprint templates for that user and an entered code or card PRintX interacts with a PRintX 40 unit Erase deleting one or all stored templates from the memory 6 1 Operation Status Indicator LED A flashing orange LED indicates that the employee is Flashing orange requested to pla
7. od working order Do e You should always touch the conductive plastic before touching the PRintX P sensor in order to safely discharge any static electricity on your skin or clothing Do not e Place the fingerprint sensor close to a heating source such as a radiator or hot plate e Spill any liquids on the sensor with the exception of isopropyl alcohol e Subject the fingerprint sensor to heavy shocks or vibrations e Allow the sensor to come in contact with metallic objects Synel Industries Ltd 10

PRintX-FPR

Contents

Download Pdf Manuals

Related Search

Related Contents