Travelite 375r
Contents
1. The mount bushing on the L bracket allows for two possible ways of mounting to the stand support RIGHT Method B may be found useful if the light is required to point down calumetphoto com HI Flash Power Control TRAVELITE The flash power control output level is variable over 5 stops from full to 1 32 power The maximum power available depends upon the model See specification table and is denoted by the numbers 1 6 on the side control panel The power settings are denoted in 1 5 stops The numeric divisions indicate full stop divisions When switched on from either AC or battery supply the unit will charge Once the unit has charged to the desired power level the green flash ready lamp will illuminate indicating that the unit is ready to fire Note If the unit is subjected to rapid operation over extended periods it may automatically go into an overheat condition In this condition the flash ready lamp will blink to indicate overheat and modeling functions will be disabled in order to allow the unit to cool The unit will automatically resume operation once cooled sufficiently In an overheat condition the unit will typically take 20 minutes to cool down By switching the unit off and then on again after approximately 10 minutes the unit can be re activated in order to get a few extra shots if needed Modeling Lamp Controls The modeling lamp control output level is variable over 5 stops from full to 1 32 power2. AC Batte E ry Middle Continuous Power Selec Bottom Off Lamp Level Top Proportional AC Inlet Middle Full Bottom User Set Fuse land Spare Fuse Sync Socket 85 130W 10AF Battery Power Inlet Photocell Reflector Release Flash Power Control Modeling Lamp Control Flash Ready Open flashTest A calumetphoto com TRAVELITE Connecting and Using Your Travelite Operating Your Travelite The Calumet Travelite may be operated either on an AC supply or with a Calumet Travel Pak For AC operation the AC switch page 4 should be in the upper position P9 For battery operation the switch should be in the lower position The center position is OFF NOTE When operated from a battery source the modeling functions are not available e Ensure the power source is off e Connect the unit using the appropriate cable e lf using the Travel Pak ensure the connector locks are fully tightened e Switch the power source on then switch on the Travelite e The unit will charge and indicate it is ready for use by illuminating the green flash ready light e Press the test button to check the unit fires WARNING HIGH VOLTAGE NEVER CONNECT THE TRAVELITE TO BOTH AC SUPPLY AND BATTERY SUPPLY AT THE SAME TIME THIS APPLIANCE MUST BE GROUNDED WHEN USED WITH AC DISCONNECT THE AC PLUG WHEN CHANGING MODELING LAMPS AND FLASH TUBES Mounting Your Travelite Mount your Travelite on a dependable support system
3. 485 On Off 2 5w Photoflood 250w Halostar 6 4 lbs 6 x 15 x 5 50ws 5V 5600 K 300 K 10A F 95 130V AC 60 Hz 1 350 2 6 Sec Full to 1 32 5 stops Mode Intermittent Continuous Off Level Proportional Full User 250w Supplied 1 650 Full to 1 32 5 stops 100 Clear BW1486 UV BW1485 On Off 2 5w Photoflood 250w Halostar 7 5 Ibs 6 x 15 x 5 Due to our policy of constant product improvement Calumet Photographic reserves the right to change eguipment specifications at any time and without notice calumetphoto com 11 U S A 630 860 7447 x2258 United Kingdom 08000 964396 Germany 040 4231600 Belgium 31 20 697 7171 IT S WHERE THE PROS GO Netherlands 020 697 7171 Calumet Travelite Five year Parts and Labor Warranty Calumet warrants the Travelite Flash Units to be free from defects in material and workmanship for five years from date of purchase If this product is found to be defective in material or workmanship Calumet Photographic will at its option repair or replace it without charge subject to the following limitations and exclusions e Warranty extends to the original purchaser only and is not transferable or assignable e Returned product must be accompanied with proof of purchase e Warranty shall not apply to any product which has in Calumet s judgment been subject to misuse abuse negligence accident or unauthorized repair e Tube lamp pc cord fuse and power cord are not covered
4. The modeling lamp control dial is denoted by the numbers 1 6 on the side control panel The power settings are denoted in 14 stops The numeric divisions indicate full stop divisions The 3 position lamp mode control switch on the rear panel controls the following functions Top Intermittent Lamp goes out when unit is flashed and comes back on when the unit is ready Middle Continuous Lamp stays illuminated regardless of ready state Bottom Off Lamp is off The 3 position lamp level control switch on the rear panel controls the following functions Top Proportional Lamp level varies proportionately to the flash power control dial Middle Full Lamp level is maximum regardless of modeling lamp control dial settings Bottom User Set Lamp level varies with the modeling lamp control dial Ready Indication The illuminated open flash test button on the side of the unit shows the charge state as follows Power down LED off Battery mode only when charger has powered down Charging LED flashes quickly Ready LED lit continuously Dumping LED flashes slowly 6 calumetphoto com TRAVE LI TE Synchronization There are several ways to trigger your Travelite Open Flash For testing or multiple flash applications the open flash button can be used Sync Socket The standard 1 4 socket on the rear panel of the unit may be used for direct connection to a camera set to X synchronization Two Travelites m
5. Ti A Radio Enabled e USER GUIDE Table of Contents TRAVELITE Description Page Introduction Safety Notes Control Panel Guide Connecting and Using Your Travelite Flash Power Control Modeling Lamp Controls Ready Indication Synchronization Changing the Modeling Lamp Changing the Fuse Y N N N OD E DY GM Pp O Changing the Flash Tube Travelite Accessories 8 9 Mounting and Removing Reflectors 9 Specifications 10 11 2 calumetphoto com TRAVELITE Introduction Dear Valued Customer Thank you for choosing the Calumet Travelite professional flash system Accurate ergonomic powerful and simple to use the Travelite was designed by working closely with photographers to develop a flash that meets the high standards demanded in professional studios today All S Type accessories from the Calumet Bowens range can be used with the Travelite For details of all related products please call 1 800 CALUMET 225 8638 contact your local Calumet retail center or visit calumetphoto com In order to obtain the full benefit from your purchase please take a few moments to familiarize yourself with this user manual Thank you Calumet Photographic Safety Notes ALWAYS e Always switch power off and disconnect from the supply before changing modeling bulb or flash tube e Always disconnect the supply before changing the fuse Never replace with a fuse of a different rating A spare fuse
6. ay be connected together using a Y connector An Infrared receiver or flash slave may also be plugged into this socket The socket operates at 5V and Is safe for use on digital cameras Built in Photocell The Travelite has a built in switchable photocell enabling the unit to be triggered by the flash from any other flash unit or a small camera mounted flash gun It is mounted behind the red transparent cover on the top ofthe unit The photocell on off switch is located on the rear control panel Radio Freguency RF Card Module The Travelite unit can be triggered wirelessly by purchasing and installing either a Calumet LiteLink Radio Trigger Card Kit CE1561 or Calumet Radio Card Kit for PocketWizard CE1563 and using their respective trigger unit Kits include one radio trigger card and one plug in antenna Changing the Modeling Lamp Switch off Travelite and disconnect from the power supply Allow lamp to cool before removing Unscrew modeling lamp from lampholder in the center of the reflector and replace with new lamp Note It is recommended that a Photoflood or Halostar bulb with a maximum wattage of 275 watts is used The manufacturer will not accept liability on the use of any lamp with a greater wattage than 275 Changing the Fuse The modeling and flash circuitry is protected by a single 10 amp fuse mounted on the rear panel Never replace the fuse with one of a different rating As the fuse may blow when the modelin
7. by this warranty Calumets obligation is limited to repair or replacement only and no one Is authorized to assume any obligation not in accordance with the above For technical assistance or to place an order call toll free 1 800 CALUMET 225 8638 CALUMET PHOTOGRAPHIC 2009 Calumet Photographic Inc All rights reserved Bowens is a registered trademark of Bowens International LTD All other www calumetphoto com trademarks are the property of their respective owners BWL 0550 04 09
8. charge option to prolong battery Universal 2 Amp SLA Charger CE1108 life no location photographer should be without small Battery BW7690 this unigue power pack Karge AA Dimensions 6 7 w x 5 5 d x 8 h Weight 11 lbs Includes small battery charger El calumetphoto com and head cable Travel Pak BW7693 Accessories Reflectors Calumet s light control reflectors are built to withstand many years of rigorous daily use They feature extremely strong housing and steel bayonet type mounts for guick positive mounting The inner steel ring provides additional durability for freguent reflector changes From studio sets to location sites Calumet s comprehensive system of accessories can handle any situation or assignment Mounting and Removing Reflectors A range of reflectors is available for your Travelite To mount slide the neck of the reflector over the front of the unit Align the three pegs on the reflector with the three slots in the retaining ring Press down and turn clockwise to lock To remove reflector pull back reflector release page 4 turn the reflector fully anti clockwise and withdraw If an umbrella is to be used a 6 Umbrella reflector should be mounted and the umbrella fitted through the hole in the mounting bracket on the reflector and locked in position with the knurled screw Note Take care when mounting and removing reflectors not to damage the flash tube assembly The flash tube is very delicate avoid
9. g lamp fails always check the fuse when replacing the bulb A spare fuse is supplied in the fuse holder Always switch the unit off and disconnect the Travelite unit from the power supply before changing the fuse Changing the Flash Tube Ensure that the unit is switched off and disconnected from the AC supply and then wait thirty minutes before touching removing flash tube Remove the protective cap and unwind the twisted trigger wire from the flash tube support Gently pull the flash tube assembly out of the unit To replace the assembly hold the flash tube as shown and taking care to support both legs of the tube gently but firmly push the flash tube into position and wind the trigger wire around the flash tube support Always replace with the correct flash tube assembly UV Coated BW1485 Clear BW1486 calumetphoto com EA TRAVELITE LiteLink Radio Trigger System LiteLink Radio Trigger System With the Calumet LiteLink Radio Trigger system you can free yourself from sync cables This multifunctional device can be used to trigger flash units film and digital cameras and light meters up to 300 away Because Litelink is a radio transmitter rather than IR it allows for triggering around corners or through walls and is not affected by high ambient light situations Choose from four individual channels each providing a unique ID for different flash devices or combine them to trigger all equipment within a given set
10. is fitted in the fuse holder under the AC inlet see page 4 e Always exercise care when handling eguipment that has been in use The reflector and front end of the unit can become Very Hot e Always avoid placing cables where they can be tripped over Protect from heavy sharp or hot objects which may cause damage and replace damaged cables immediately e Due to the high voltage high energy used in Travelites all servicing must be carried out by a Calumet authorized service center e Always remove the power cord by gripping the plug NEVER pull the cord e Always ensure that any extension cord used has a sultable current rating to prevent overheating and never use coiled extension cords e Always remove the flash head covers before USING DO NOT S e Do not use in an environment where moisture or flammable vapor is likely to come in contact with the unit e Do not plug your Travelite into an AC supply and a Travel Pak battery at the same time e Do not restrict air vents while in use e Do not use a unit with damaged housing moldings flash tube or modeling lamp If the unit is dropped or damaged in any way always have it checked out before using e Do not operate the unit without a safe grounded AC supply calumetphoto com EN Control Panel Guide TRAVELITE Rear Control Panel Carry handle RF Module Cover Plug in Antenna Photocell On Off Sold Separately Lamp Mode Top Intermittent
11. unnecessary handling of the glass tube Always switch the unit off and disconnect from power supply before fitting and changing reflectors WARNING HIGH VOLTAGE DO NOT TOUCH THE FLASH TUBE ASSEMBLY FOR d 30 MINUTES AFTER DISCONNECTING FROM SUPPLY 6 Umbrella Reflector 120 7 Grid Reflector CE1885 CE18630 High Performance Back Lite Reflector Reflector CE2560 BW1878 CE1886 15 Soft Lite Reflector CE1899 17 Sunlite Reflector 40 CE1868 8 Reflector 60 CE1887 Visit calumetphoto com for the widest range of photographic lighting accessories calumetphoto com EA TRAVELITE Radio Enabled Maximum Stored Energy Sync Voltage Flash Color Temperature Circuit Protection Supply Voltage Voltage Stabilization Guide Number Full Power 50 Keylite ISO 100 Typical Recycle Time Full Power Modeling Lamp Control Modeling Control Switches Modeling Lamp Flash Duration t 0 5 Full Power Flash Power Control Flash Ready Indication User Replaceable Flash Tube Photocell Recommended Modeling Lamps Weight Dimensions w x x h 101 calumetphoto com Travelite Specifications Comparison Chart Travelite 375r Travelite 750r 3 5ws 5V 5600 K 300 K 10A F 95 130V AC 60Hz 1 220 1 7 sec Full to 1 32 5 stops Mode Intermittent Continuous Off Level Proportional Full User 250w Supplied 1 900 Full to 1 32 5 stops 100 Clear BW1486 UV BW1
12. up or studio Because of its low voltage operation it is perfect for digital cameras Each unit can be used as either a transmitter or receiver and operates off of two AAA batteries LiteLink Set of 2 CE1560 Radio Trigger Card Kits These simple kits upgrade Calumet Travelite and Bowens Gemini R radio enabled monolights to become compatible with LiteLink and all U S PocketWizard Radio Trigger Systems Kits include radio trigger card plug in antenna and Blas lt Malli Plug in antenna into side Insert Radio Trigger Card Ap AA acts IEEE of unit Remove RF into slot and replace RF Calumet LiteLink Radio Card Kit CE1561 Module Cover Module Cover Calumet Radio Trigger Kit for PocketWizard CE1563 The Bowens Travel Pak The Bowens Travel Pak Starter Kit The Travelite is great in the studio but what if you need to work on location Thanks to this handy battery pack your Calumet Travelite can leave the studio to go on location anytime anywhere travelpak Able to power two Travelites simultaneously with a total power of up to 1500ws the Travel Pak is capable of bringing a 375ws unit to full charge as fast as 4 seconds and can offer in excess of 200 flashes on a single charge The large battery offers double capacity compared to its smaller l CHARGE Ano WT Om Lai Also available for the Bowens Travel Pak Travel Pak to Travelite Spare Cable CE1111 counterpart Travel Pak 26 Cable BW7632 With a fast slow
Download Pdf Manuals
Related Search