Home

AUTO-i 700 Manual

1. P2122 TPS APS1 Signal Low P2127 Accelerator Position Sensor 2 Signal Circuit Low Input P2104 Limp Home Mode Forced Idle P1295 Limp Home Mode Power Management position APP sensor B low input Change Unit Full Screen Red Marker function s available n the full screen mode OA ress this button to activate the red marker function Then click on the screen and drag it to make a mark oalll press this button to delete all records by the red marker function before saving ech this button to save the written contents all p ess this button to switch to other screen if data of many items are selected You can use the red marker function on the switched screens cl press this button to deactivate the function 38 CARMAN INTERNATIONAL AU TO i 700 Chapter 5 Diagnosis Menu 1 How To Connect Diagnostic Connector and Select Diagnosis Program It is common to Korean Janpanese European and USA vehicles 1 Locate the diagnostic connector in the vehicle Most vehicles released after year 2002 conform to the OBD II Protocol and have OBD II diagnostic connectors Most OBD II vehicles have their diagnostic connectors on the section over the brake pedal under the steering wheel If an additional adaptor is required the scanner display shows the type of the necessary adaptor and the location of the diagnostic connector LOCATION DRIVER S DASH BOARD Location
2. 9 SYSTEM INFORMATION PCM LOCK MEC SETTING IGN KEY ON CONDITION ENGINE STOP see IE YOU READY PRESSItSET Kaze 56 AUTO i 700 CARMAN veson Chapter 6 Vehicle Diagnosis 8 Misfire Delay Reason This function is to check the number of misfire in each cylinders System information differs from depend on car makers and models 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR 1 DIAGNOSTIC TROUBLE CODES ERASE RESET DTC PARAMETER DATA ACTUATOR TEST RESETTING ADAPTIVE VALUES 2 3 4 5 6 EVAP LEAKAGE TEST 7 PCM LOCK MEC SETTING A MISFIRE DELAY RESON HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR 01 02 03 05 06 07 08 CYL 1 CYL 2 SCHI 04 CYL 4 CYL 5 CYL 6 TOTAL MISFIRE DELAY MISFIRE MISFIRE MISFIRE MISFIRE MISFIRE MISFIRE MISFIRE NO DELAY F2 F3 CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT CURRENT REASON 5 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 9 System Information System Information shows information related with system such as system model and software version etc System information differs from depend on car makers and models 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR DIAGNOSTIC TROUBLE CODES
3. check the vehicle condition and the connection status of the diagnostic connector again mj 46 CARMAN INTERNATIONAL AU TO i 700 Chapter 6 Vehicle Diagnosis 2 The Live data list is displayed as shown in the below picture pe cw 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR SENSOR VALUE UNIT Battery Voltage Main Relay Cooling Temperature Sensor Oil Temperature Air Flow Sensor Intake Temperature Sensor Manifold Absolute Pressure MAP Sensor Barometric Pressure Sensor Engine Speed Graph Mode File Mode Dual DTC Live Data gt gt Graph mode Press th s button to check live data in graphs Press this button to check live data in graphs lt is helpful to convert the current vehicle data to graphs for tendency analysis Up to 30 items can be selected while up to 8 graphs can be displayed at a time To convert live data to graphs such data are need to be fixed Then only these fixed data change File mode Press this button to save sensor data or check the saved files Data are stored in the internal memory and they can be stored synchronized with your PC Dual DTC Press this button to display DTCs at once Guide Info If the selected system has help information this button is activated Then press this button to display information Later it will be supported Change Unit Press this button to move to configuration and ch
4. 3 RJ45 It is not supported just now Later it is supposed to support A Please do not insert a LAN cable 4 DLC connector It is for DLC communication cable to diagnose vehicles Hole for a touch pen It is for keeping touch pen Connectors on left side Connectors on right side D D E 4 Forced Termination This switch can interrupt power emergently if it is overloaded while using 2 USB A Type Connecting to external device 3 HDMI Connecting to external monitor later it will be supported by update 4 USB B TPYE Connecting to PC for update 5 USB mini B USB port for support J2534 communication Later it will be supported on our website 6 J2534 power port power port forJ2534 Later it will be supported on our website 12 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions 6 4 AUTO 1 700 Carrying Case AUTO 1 700 Carrying Case AUTO 1 700 includes a number of adaptors and cables for diagnosing vehicles When the product is not in use store it in the supplied carrying case to prevent damage and loss 6 5 Touch pen Picture no 1 Touch Pen Picture no 2 Hole for Touch Pen You can prevent the touch pen from loss or damage by keeping it into the hole for touch pen like the picture no 2 13 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions 6 6 Rubber Shroud fit to the main body initially The color of rubber shroud can be
5. Chapter 6 Vehicle Diagnosis If it does not show a menu like page 42 and shows Communication Error or does not communicate stably please check first status of the target car km KIA KOREA DOMESTIC Ray Engine Gasoline 1 0 MPI OBD II 16PIN CONNECTOR 4 gt TXT or connection of cables Diagnostic Trouble Code 2 The DTC search screen appears Now you can check current and old DTCs and erase them i p Old DTCs are not activated unless there is no corresponding fault history Diagnostic Trouble Codes detected only when the list save applies can be saved 3 Press DTC to check current troubles 43 CARMAN INTERNATIONAL AUTO i 700 Chapter 6 Vehicle Diagnosis mon i i EN HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR A TXT P2122 TPS APS1 Signal Low ol P2127 Accelerator Position Sensor 2 Signal Circuit Low Input P2104 Limp Home Mode Forced Idle P1295 Limp Home Mode Power Management P0222 Throttle position TP sensor B accelerator pedal position APP sensor B low input sey P0123 Throttle position TP sensor A accelerator pedal position APP sensor A high in P0107 Manifold abosolute pressure MAP sensor barometric pressure BARO sensor P1107 Manifold Absolute Pressure Sensor Circuit Intermittent low ES P0452 Evaporative emission EVAP pressure sensor low input P0685 ECM power relay contr
6. i 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR 1 Throttle Position Sensor 1 130 3 2 Battery Voltage 3 Target Idle Speed 1620 0 rpm Flight Record Start 4 Throttle Pc 132 1 Record Data Viewer Text Mode File Mode Dual DTC Flight Record Start Press this button to start to record the selected live data The data can be recorded for up to 1 hour and the recording time can vary depending on the number of the selected live data When the recording operation is performed for 1 hour it stops automatically Only selected Flight record data by user is saved Ki On the other hand if a user select some list only the selected list is saved but if a user select nothing all list is saved Record Data Viewer Press this button to check or search for the stored file The screen displays the Record Data menu pane where you can check the saved data through the flight record list For the flight record text shot screen capture and gas analyzer functions refer to Chapter 4 Record Data 49 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis Dual DTC The upper half of the screen displays the live data while the lower half of the screen displays the DTC list if there is any DTC the corresponding sensor data can be checked for comparison SENSOR 1 0 Battery Voltage 0 0 11 6 Target Idle Speed 1620 rpm 1620 0 1620 0 Ba
7. ERASE RESET DTC PARAMETER DATA ACTUATOR TEST EVAP LEAKAGE TEST PCM LOCK MEC SETTING 2 3 4 9 RESETTING ADAPTIVE VALUES 6 D 8 MISFIRE DELAY RESON 9 SYSTEM INFORMATION 58 CARIAN INTERNATIONAL AUTO 700 Chapter 7 OBD II EOBDDiagnosis Menu 1 OBD I EOBDOverview E Purpose ofOBD II EOBD OBD II EOBDis intended to find what caused the emission to increase diagnose the part of thecause and light the warning lamp in order to provide faster and more precise repair E OBD II EOBDRegulations If emission increases due to defected parts diagnose components and cause and turn on the Malfunction Indicator Lamp MIL Trouble information shall be read by the standard diagnosis tools GST EM OBD II EOBDRegulations Major Check List The warning light shall be on before the emission reaches 1 5 times of the permissible limitdue to any of the following troubles or performance degradation Catalyst purification rate this diagnosis is for HC emission only This is being phased in for 1 75 times of HC limit from TLEV misfire EGR System O2 sensor and fuel system secondary air system Diagnose all sensors and actuators used for controlling the engine to see if they function properly as well as wirings for an open short circuit Diagnose the entire evaporation system to see if it leaks Perform diagnosis when the PCV valve and the crankcase or the PCV valve and the intake manifol
8. Absolute Pressure M999 8 Barometric Pressure Sensor 101 0 Engine Speed 0 Target Idle Speed Idle State Vehicle Speed Sensor 2 1 Full Screen It shows recorded data of selected item in full screen 2 2 Delete It delete a selected item 2 3 Change filename User can change a file name Chapter 4 Utility 36 CARMAN INTERNATIONAL AUTO 700 3 Screen Capture Press the button on the left upper s de f you need to capture screens while using Conveniently screens are saved TS Image List 40820_134741 40820_134746 0140820_134756 0140820_134801 Screen Capture 0140820_134807 0140820_134908_ 40820_135716_OB 40820_135725_OB 0140820_150717 Full Screen Slide Show Rename Delete Screen Capture 3 1 Full Screen Press this button to show the saved files on a full screen Red marker function is available in the full screen mode the Red Pen function makes a user take a note on the screen and edit it freely 3 2 Slide Show Select several files and press this button to display them in a slideshow 3 3 Rename Press this button to rename the file 3 4 Delete Press this button to delete a file 3 5 Initialization Press this button to initialize by deleting all saved files 3 6 Save Press this button to save changed items P Lobe Unnecessary buttons may not be saved in some items 37 CARMAN INTERNATIONAL AUTO 700 Chapter 4 Utility
9. Wire Duty A B1S1 0 5 A ajaja DIAG MENU 1 2 Intake Temperature Sensor 48 0 C DTC 3 Throttle Position Sensor 1 130 3 03 Injector 3 Time UNTIL STOP KEY PRESS Method DEACTIVATION Condition IG KEY ON ENGINE RUNNING Result PRESS STRT IF YOU ARE READY sore rne m m Actuator graph mode 5 In the figure 3 1 Press Show sensor button to see sensor data After selecting a sensor data Press the graph mode button to change data value to a graph The actuation result 1s judged by noise from the running actuator or Lobe switch and vehicle RPM change Therefore it is recommended to perform the actuation test in a quiet area and use current data values as a reference Lobe If target system does not support sensor actuator and dual display it supports items of actuator without items of sensor 53 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 5 Resetting Adaptive Values The resetting adaptive values initiates ECU by clearing values of sets in ECU The clearing learning values may be different depend on car makers and models 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR cU 1 DIAGNOSTIC TROUBLE CODES Hoo 2 ERASE RESET DTC A 3 PARAMETER DATA DTC 4 ACTUATOR TEST 9 RESETTING ADAPTIVE VALUES 6 EVAP LEAKAGE TEST 2 7 PCM LOCK MEC SETTING JA 8 MISFIRE DELAY RESON 9
10. display the data only selected by the user Battery Voltage Coolina Temperature Sensor Main Relav Cooling T Se 3 emperature Sensor Warnina Lamp State ng rompe 48 0 C Main Relay Warning Lamp State Text View Graph View 1 2 Delete Click this button to delete the file selected by the user 1 3 Rename Click this button to rename the file that was temporarily set when saving the file only in English Chapter 4 Utility 35 CARMAN INTERNATIONAL AU TO i 700 2 Text Shot You can save a measured value you select among system error code and sensor data by choosing specific time during diagnosis and you can use the values of specific time to analyzation You can save all data at once So you can check whole car conveniently 0131121 _145154_HYUNDAI Model HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR Date 11 21 2013 14 52 Sensor Value Warning Li ON Battery Vol E Main Relay ON Cooling Te 16 5 Oil Temper 16 5 A Air Flow Se 0 0 Intake Ten 48 0 Manifold A 999 8 Barometric 101 0 Engine Spe 0 Text Shot Model HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR Date 11 21 2013 14 52 Sensor Warning Lamp State Battery Voltage Main Relay Cooling Temperature Sensor 16 5 Oil Temperature 16 5 Air Flow Sensor 0 0 Intake Temperature Sensor 48 0 Manifold
11. of OBD II diagnostic connector 2 Use the DLC main cable to connect the vehicle s diagnostic connector and AUTO 1 700 3 Turn on AUTO 1 700 If power is not feed through the diagnostic connector and the AUTO 1 700 battery 1s not fully charged you need to connect an additional power supply vehicle battery or cigarette lighter power cable etc 4 Select a kind of vehicle 39 CARMAN ao AUTO i 700 Chapter 5 Diagnosis Menu 5 Select the maker of the vehicle to diagnose RECENT LIST GM DAEWOO HYUNDAI HYUNDAI CHEVROLET DOMESTIC EXPORT HYUNDAI USA RENAULT SAMSUNG Vehicle Maker Selection 6 Select a vehicle on diagnosis menu D 0 HYUNDAI KOREA DOMESTIC HYUNDAI ee Tucson Tucson IX LM Veracruz i40 VF i30 FD i30 GD Genesis Genesis Coupe HE EEE o Vehicle Model selection C O nn 40 carmnn INTERNATIONAL AU TO E i 700 Chapter 5 Diagnosis Menu 7 Select the system to be diagnose 8 0 HYUNDAI KOREA DOMESTIC Veracruz HYUNDAI deren QUICK SEARCHING MODE Engine Gasoline Veracruz Engine Diesel Automatic Transaxle Auto Aircon 4WD Electric Power Steering Auto Head Leveling System Power Tailgate Body Control Module BCM Airbag Brake System ABS VDC System Selection Diagnostic Connector Type TOYOTA models use same connectors with Lexus models 1 16 pin connector common OBD II connector 2 semi circul
12. on please select a item to edit click the edit button on below bar and input information 5 3 Other languages except English can be input using download program of PC Chapter 3 Configuration 33 CARMAN INTERNATIONAL AU TO z i 700 System Information Program Information MODEL AUTO i 700 PROGRAM Main OS Windows CE 6 0 VER 140814 VERSION 20140708 PROGRAM Utility VER 140814 SERIAL NO FIRMWARE VER 12 2 PROGRAM Configration VER 140814 PROGRAM Update VER 140814 All rights reserved Information This computer program is protected under Korean and International laws User Info Information 5 4 Press the Information button Then the information is shown so you can check system and program Chapter 4 Utility 34 CARMAN INTERNATIONAL AUTO i 700 This function is to check flight records text shots and screen captures etc 1 Flight Record You can save service data of a vehicle to analyze it Refer to P49 You can save the desired service data This function is useful when data should be saved to diagnose an intermittent symptom Bai Flight Record 0131121_145059_HYUNDAI Flight Record v HYUNDAI KOREA DOMEST Veracruz Engine Gasoline OBD II 16PIN CONNECTOF 11 21 2013 14 50 4 Battery Voltage Cooling Temperature Senso Main Relay Warning Lamp State Flight Record 1 1 Data View Click this button to
13. 45 D Ee 46 SCI OL EE ee ol Resetting Adaptive Vals rare are 54 EVYAP Leakage KE oo PCM GOckiME e 56 eh Wii ot Per ee ee D7 O o N Q Oo gt Pei soyo et e EE 58 pei Ie Per E 64 Diagnostic Trouble Ce a chi ress aa en aa era ee 66 e Eeer DD ee 68 Monitoring Te ee nee 69 Bee E 12 Aa A gt gt e Dien ECH EE EEN to CHAPTER 9 Program Download 15 eege En CR E 76 Certificate of Information and Communication boupment 78 NARRE RE 19 CARMAN ao AUTO i 700 Safety Instruction Cautions in Use AUTO 1 700 mentioned in this User s Guide is designed for those who have basic qualifications for using this system Users should follow the safety instructions for safe and efficient use of the product The cautions of use are as follows Do not drop AUTO 1 700 Always use it in the rubber shroud to product it Do not place AUTO 1 700on the power distributor Althoush AUTO 1 700 s manufactured to internally prevent the interference from the electromagnetic waves the strong interference by excessive electromagnetic waves may damage the product Excessive surge or electric shock fed by a power cable may damage the power supply system of AUTO 1 700 So do not use the product while the power supply is unstable The voltage rating of the AC DC adapter is 12V DC Be sure to use an AC DC adaptor with the rated voltage Be careful not to let water or o l get i
14. CARMAN INTERNATIONAL AUTO 700 User Guide Ver 140801A Safety Cautions This information is essential to protect your safety and prevent property damage Make sure to read this thoroughly before using AUTO 1700 This information is subject to change or add without notice Please refer to Homepage of Carman International Co Ltd for the latest version Grade A Equipment Communication Equipment for business purpose Pay attention that this is electromagnetic compatibility equipment for business purpose Grade A It is permitted to use except a house CARMAN INTERNATIONAL CO LTD CIRIAN INTERNATIONAL AUTO 700 Table of Contents CAO WEE 4 CHAPTER 1General Descerptons ccc cececcececccccececcecececeececeueceeueaeeceneuees S t Producti ae D E gell ei Wee Ee e e 6 3 Rechargeable Beatie E f L Component Li GE 8 5 Component Figures and Descr ptions ce 11 BD Power SUD DIV anne 24 CHAPTER 2Menu Confeurapon nennen 25 IL Before Getting SEAT ER E 25 2s Nena CT as ee ee ee een ee 26 Et EG 27 RE 31 Mag Kr EEN 32 SW NO AICI 0 PO NE EEE EE TOS a CHAPTER 4Record Tara SIS le EN MO EE 35 AA OXI OEE a 36 EMS Creen Apl ee EE EE 37 CARMAN INTERNATIONAL AUTO 700 CHAPTER 5Diagnosis Men 39 1 How To Connect Self Diagnostic Connector and Select Diagnosis Programi ER 39 CHAPTER 6Vehicle Daoenoesg een een 42 Diagnostic Trouble en EE 42 Erase reset KE
15. MAN INTERNATIONAL AU TO E i 700 Chapter 6 Vehicle Diagnosis 2 The screen as below appears 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR Injector 1 DIAG MENU Injector 2 A Injector 3 DTC Injector 4 Injector 5 Injector 6 Immobilizer Warning Lamp Fuel Pump Relay Fuel Pump Control Fan High Speed Fan Low Speed Actuator 3 Press the start button after selecting a item O HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR 04 Injector 4 05 Injector 5 06 Injector 6 07 Immobilizer Warning Lamp 08 Fuel Pump Relay LIVE DATA 04 Injector 4 Time UNTIL STOP KEY PRESS Method DEACTIVATION Condition IG KEY ON ENGINE RUNNING Result PRESS STRT IF YOU ARE READY Figure 3 1 Actuator Start amp Stop 52 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis Before starting actuation make sure to check the operating condition to inspect the system in the proper condition The actuator time differs by the actuated items 4 Press the Stop button to stop the actuator function Press this button to stop the actuator function during diagnosis Press the arrow button on the right top corner of the screen to stop the actuator function too ro L 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR TXT BER 1 Oxygen Sensor Hot
16. ORTED Fuel System Monitoring Supported SUPPORTED Comprehensive Component Monitoring Supported SUPPORTED Compression Ignition Monitoring Supported Spark IG _ Misfire Monitoring Ready COMPLETED Fuel System Monitoring Ready COMPLETED Comprehensive Component Monitoring Ready COMPLETED Catalyst Monitoring Supported NOT SUPRTD Heated Catalyst Monitoring Supported NOT SUPRTD Readiness Test Results 1 NOT CMPLTD The test has not been completed This appears when the test was not completed owing to the abnormal ECU or sensorrequired to display the test result 2 COMPLETED The test has been completed 3 NON APPLIC The item is not applied to the tested vehicle 63 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 2 PARAMETER DATA You can check the PARAMETER DATA specified by the OBD II EOBD standard in this menu 0 SE 1 M01 READINESS TEST 2 M01 PARAMETER DATA 3 M03 DIAGNOSTIC TROUBLE CODES 4 M04 ERASE RESET DTC 9 M06 MONITORING TEST RESULTS 6 M08 BI DIRECTIONAL CONTROL 7 M09 VEHICLE INFORMATION PARAMETER DATA Selection 2 1 If communication with the vehicle is established successfully the above menu appears Select the PARAMETER DATA If no menu like above picture is diplayed or communication cannot be ESP established check the vehicle condition and the connection status of the diagnostic connector again In addit
17. SYSTEM INFORMATION 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR RESETTING ADAPTIVE VALUES PCM AUTO DETECTION RESET IGN KEY ON CONDITION ENGINE STOP PRESS REST IF YOU ARE READY REST 54 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 6 Evap Leakage Test Press this button to check if there is leakage from a oil tank ER 1 DIAGNOSTIC TROUBLE CODES 2 ERASE RESET DTC 3 PARAMETER DATA 4 ACTUATOR TEST 9 RESETTING ADAPTIVE VALUES A SE 7 PCM LOCK MEC SETTING ES 8 MISFIRE DELAY RESON SYS INFO 9 SYSTEM INFORMATION HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR KKKKKKKKKKKKK KKK KKK KKK KKK ENGINE START KKKKKKKKKKKKK KKK KKK KKK KKK IF YOU READY PRESS TENTER KEY 55 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 7 PCM Lock MEC Setting This function is to prevent data or programs from adjustment System information differs from depend on car makers and models 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR DIAGNOSTIC TROUBLE CODES ERASE RESET DTC PARAMETER DATA ACTUATOR TEST eae RESETTING ADAPTIVE VALUES a EVAP LEAKAGE TEST 7 PCM LOCK MEC SETTING gt 8 MISFIRE DELAY RESON SYS INFO
18. ange system Unit and time etc Please refer to Chapter 3 Configuration for more information E _ _ 4 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis e If you use the fix function values are changed only for the fixed items so you can measure changed values faster and can diagnose more precisely Graph Mode This function is to check live data in graph forms for tendency analysis 0 HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR 1 Throttle Position Sensor 1 130 3 2 Battery Voltage 3 Target Idle Speed 1620 0 rpm 4 Throttle Position Sensor 2 132 1 Text Mode File Mode Dual DTC Graph Mode Text Mode Press this button to switch to the text mode File Mode Press this button to save data and check saved files Dual DTC Press this button to check DTC and sensor data at the same time Auto Press this button to reset graph based on the maximum and minimum values from ECU up A down V In the graph view mode up to 8 live data can be displayed at a time If the number of sensor data displayed on the screen at a time is set to less than 8 the remaining live data are displayed in the list on the bottom Reset Press this button to initiate the Graph View S u 48 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis File Mode Press this button to save data or check the saved data pe
19. ar connector Toyota 17 pin C type connector 3 Rectangular connector Toyota 17 pin R type connector Loupe The screen displays the vehicle diagnostic connector by a vehiclemaker 41 CARIAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 1 Diagnostic Trouble Codes In this menu it s possible to check for any malfunction of the selected vehicle system through the communication with the ECU in the vehicle As AUTO 1 7OOdisplays DTCs Diagnostic Trouble Codes you can easily check where malfunction occurs Also the description for DTCs is displayed as well to help you service your vehicle In order to diagnose DTC correctly please check the connection between connector and AUTO 1 700 Please refer to Chapter5 Diagnosis menu and check details such as Vehicle maker model and displacement etc The helpfunction may differ between vehicle makers ER 1 DIAGNOSTIC TROUBLE CODES LD 2 ERASE RESET DTC 3 PARAMETER DATA 4 ACTUATOR TEST 9 RESETTING ADAPTIVE VALUES EVAP LEAKAGE TEST PCM LOCK MEC SETTING MISFIRE DELAY RESON SYSTEM INFORMATION Picture 1 1 Diagnostic Trouble Codes Note Items of Diagnostic Trouble Codes may differ from depending on makers and models l If a car and a system are selected correctly in the Vehicle Diagnosis menu and communication with vehicle is stable the above picture will be shown 42 CARMAN INTERNATIONAL AU TO i 700
20. bove menu is not appeared and Communication cannot be Lobe established check the vehicle condition and the connection status of the diagnostic connector again Also check if your vehicle supports OBD II Communication 66 CARMAN INTERNATIONAL AUTO i 700 Chapter 8 OBD II EOBDVehicle Diagnosis P2122 Throttle Pedal Position Sensor Switch D Circuit Low P2127 Throttle Pedal Position Sensor Switch E Circuit Low P2104 Throttle Actuator Control System Forced Idle DITC 2 2 DTCs are listed on the screen as shown in above figure You can check values of each sensor Refer to the description of Chapter6 Vehicle Diagnosis for each Ke button s function Live data items in OBD II communication may be different from live data items that are checked by selecting cars because live data items in OBD II standard are provided 67 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 4 Erase Reset DTC 1 Select a car model and system in the diagnosis menu Then if communication with the vehicle is established successfully the menu shown in Figure of Page65 appears Select the ERASE RESET DTC button BD2 EOBD CAN OBD II 16PIN CONNECTOR M01 READINESS TEST M01 PARAMETER DATA _ MO DO YOU WANT TO ERASE Y N _ MO AA CONDITION KEY ON ENGINE OFF _ MO MO MO Erase Reset DTC 2 If the YES amp NO window are s
21. ce Also language can be selected according to a user OS Language ENGLISH Dispaly 3 1 OS Language The language of the operating system and diagnostic program can be set among the languages that are stored n the internal memory 3 2 Brightness Press the and buttons to adjust the screen brightness Please note that if you set up the brightness to the max the battery will be dead earlier Chapter 3 Configuration 31 CARMAN sa AUTO i 700 4 Time Set You can change the date and time stored in the internal memory The time stored in this menu is used when saving a file or executing other functions User can adjust time and date of the scanner Time Set 4 1 Date Set Change the day month and year as desired by pressing the arrow keys A and V 4 2 Time Set Change the hour and minute as desired by pressing the arrow keys u p OS language setting depending on the state set a date and time settings can be changed notation Chapter 3 Configuration 5 Information 32 CARMAN INTERNATIONAL AU TO E i 700 You can input your information or check system information Family name l Personal name Telephone Mobile ee J Fax E Mail d Company Address Information System Info Information 5 1 User information s shown and you can edit and save information 5 2 In order to change the informat
22. changed according to user Rubber Shroud The rubber shroud protects AUTO 1 700 from external electrical and physical impact 6 7 USB Cable USB Cable The USB cable connects the USB ports of Carmanscan AT and your PC to download the diagnosis software or save captured files to your PC CAUTION Please use a USB cable for AUTO 1700 only Other USB cables can cause contact problem 14 CARMAN INTERNATIONAL AU TO i 700 Chapter 1 General Descriptions See CD AUTO C 700 SCOPE 300 CARMAN Components of CD Installation Driver PC Program PDF Program Basic Diagnostic Data User Guide 6 9 Wi Fi USB Dongle Newest diagnostic data can be updated automatically via Wi Fi USB A Type Also without wire captured screens in the scanner can be printed via PC that is connected to a printer Later it will be supported through our website 15 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions on Cigarette Cable 6 10 Cigarette Cable This cigarette cable connects AUTO 1 700 and a vehicle so that it can supply power e AUTO 1 700 has internal battery inside so it can boot without other power but if power of batter is low and it is not charged you can use cigarette cable or AC DC power adapter 6 11 Battery Extension Cable Battery Extension Cable This battery extension cable make AUTO 1 700 to get power from ba
23. d are disconnected Diagnose the thermostat when the coolant temperature fails to reach the specified temperature where the diagnosis can be made to other items in a given time after starting the engine 59 CARMAN INTERNATIONAL AUTO 700 Chapter 7 OBD II EOBDDiagnosis Menu 2 How To Connect Diagnostic Connector and Select Diagnosis Program It is common to Korean Japanese European and USA vehicles 1 Locate the diagnostic connector in the vehicle Most OBD II vehicles have their diagnostic connectors on the section over the brake pedal under the steering wheel OBD II Diagnosticconnector location Since vehicles without the OBD II diagnostic connector do not conform tothe OBD II EOBD communication protocol you can not use the OBD I EOBD vehicle diagnosis function to them OBD II Diagnosticconnector location 2 Use the diagnosis cable to connect the vehicle s diagnostic connector and AUTO i 700 3 Turn onAUTO 1 700 As OBD II vehicles feed power through the diagnostic connector to the module they do not need any additional power supply 4 Press the OBD I EOBD button on main screen of AUTO i 700 to see diagnosis items 5 Diagnosis function includes Auto searching ISO9141 2 KWP2000 J1850PWM J 1850VPW CAN communication Figure 5 1 etc please refer to Chapter 8 OBD II Vehicle Diagnosis for more information Whenever performing diagnosis make sure that the ignition switch is in the ON pos
24. e Lighter Power Cable Power is fed through the cigarette lighter power cable However when the vehicle ignition switch is in the OFF position or upon starting a vehicle power is not supplied to the cigarette lighter socket 2 Vehicle Battery Connect the red clip of the battery extension cable to the battery terminal and black clip to the terminal Connect the cigarette lighter power cable between the battery extension cable and the product In this case power is supplied anytime regardless of the ignition switch status or vehicle starting Be careful no to discharge the battery A DANGER Be careful when connecting the cable as incorrect polarity may damage the main module 3 DLC Cable Where the vehicle satisfies the OBD II communication convention and uses a certain manufacturer s diagnostic connector the DLC main cable can supply power to the product directly without a separate power supply 4 Rechargeable Battery Pack If the built in battery is used you can use the system for 3 to 4 hours without any separate power supply The available time may change based on use and environment Lobe How to charge When the product is not in use connect it to the power source by the AC DC power adapter that came with the product to charge the built in battery 12h 24h 5 AC DC Power Adapter If the AC DC adaptor is used for power supply the battery will be automatically r
25. e the device can be generated and it can cause damage or malfunction So please do not place this device in the cold if possible CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 3 Rechargeable Battery The rechargeable battery pack has the following features Voltage of the rechargeable battery pack gradually decreases even when the system does not run Before using the product for the first time be sure to fully charge the battery Always use the rechargeable battery pack provided by Our Company Using a 3rd party product may cause explosion 7 4V 2200 mAh lithium ion battery pack Do not heat the rechargeable battery pack It may cause explosion Do not short the battery pack terminal It may cause explosion Do not place the battery pack on or near hot material over 60 C It may cause explosion Keep the battery pack away from touch of children or an animal It may cause a fire or injury To prevent the battery pack from being discharged always connect the power source before using the system Screen captures flight record and other information can be erased due to the discharged battery pack The battery 1s consumable and the warranty period is 6 months from ed purchase date If the product s not used over 3 months the contained battery may be discharged and swollen Please charge your battery at least once per 2 or 3
26. echarged depending on programs and it is also used for power supply to the main module 24 CARIAN INTERNATIONAL AUTO 700 Chapter 2 Menu Configuration 1 Before Getting Started 1 1 Before using the system check whether or not the battery is fully charged If it is notcharged then connect external power supply or recharge the battery before using thesystem If you use the system by connecting it to a vehicle you can also feed power to t through the vehicle diagnostic connector If power is not feed by the vehicle diagnostic connector you need to connect the cigarette lighter power cable to feed power before you start communication with the vehicle Voltage mismatch between the ECU and AUTO 1 700 may cause a communication error 1 2 Before using the system make sure to download the diagnosis program The diagnosis program will be stored in the system memory Before using the system check if the diagnosis program matches the option youhave purchased Basically a diagnostic program 1s installed before delivery Also you can get the latest diagnostic data from our website or from where you purchase 25 CARMAN INTERNATIONAL AUTO 700 Chapter 2 Menu Configuration 2 Menu Description When turning ON AUTO 1 700 the main screen with the menu is displayed as follow Main Screen 01 OBD H EOBD This menu is to diagnose and test some parts that are related with exhaust gas on
27. ehicle supports OBD II communication 69 CARMAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis o OBD2 EOBD CAN OBD II 16PIN CONNECTOR MONITORING TEST RESULTS SELECT A ITEM Exhaust Gas Sensor Monitor Banki Exhaust Gas Sensor Monitor Bank2 5 Catalyst Monitor Banki Catalyst Monitor Bank2 EVAP Monitor Cap Off 0 150 EVAP Monitor 0 040 EVAP Monitor 0 020 Purge Flow Monitor 0 OBD2 EOBD CAN OBD II 16PIN CONNECTOR MONITORING TEST RESULTS 2 SE EEO ITEM 08 Purge Flow Monitor 09 OBD MID A2 10 OBD MID A3 11 OBD MID A4 12 OBD MID A3 13 OBD MID A6 14 OBD MID A7 Poe BBBAMIDE SEI 70 CARMAN so AUTO i 700 Chapter 8 OBD II EOBDVehicle Diagnosis 71 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 6 BI Directional Control You can control and test functions related with OBD II system M01 READINESS TEST M01 PARAMETER DATA M03 DIAGNOSTIC TROUBLE CODES M04 ERASE RESET DTC 9 M06 MONITORING TEST RESULTS 6 M08 BI DIRECTIONAL CONTROL 7 M09 VEHICLE INFORMATION BI Directional Control 6 1 If communication wih the vehicle is established successfully the menu above appears Select BI DIRECTIONAL CONTROL If no menu like picture above is displayed or communication cannot be dP established check the
28. haser within the warranty period postage pre paid together with proof of purchase date to Carman International Co LTD Defective products will be repaired at manufacturer s discretion replaced at no charge 2 The warranty does not apply to any units that have been tampered with or to damages incurred through improper use and care defects caused by abuse or through the usage for purposes other than the intended use used in a manner inconsistent with the instructions regarding use and faulty packing or mishandling by any common carrier 3 Repairs not covered by this warranty will be performed at the current cost for parts and labor In no event will Carman International Co Ltd s liability exceed the price paid for the product from direct indirect special incidental or consequential damages resulting from the use of this product its accompanying software or its documentation without obligation to notify any individual or entity Warranties hereunder extend only to customers and are not transferable Warranty Period amp Software update 1 Free Software update for Carman International products is fifteen 15 months from date of purchase After fifteen 15 months from purchase date software updates will be optional and will require separate payment per request Repair Service 1 If you suspect that you have a problem with this product please read the operation manual guide carefully to ensure that you are operating this product p
29. hown Select the YES button to clear DTC or select the NO button to return back to previous step There are current and old DTCs When trying to clear old DTCs they are cleared immediately and they are not set again However when trying to clear current rare DTCs they are cleared for a short period of time but they are activated again In this case clear DTCs again after checking and repairing malfunction parts for the corresponding DTCs 68 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 5 Monitoring Test Results This menu displays the monitoring test results while the vehicle is being normally operated To test systems and units of different manufacturers it is required to specify test IDs and component IDs If there is no test item supported by the vehicle manufacturer an error message will be displayed 1 M01 READINESS TEST 2 M01 PARAMETER DATA 3 M03 DIAGNOSTIC TROUBLE CODES 4 M04 ERASE RESET DTC 9 M06 MONITORING TEST RESULTS 6 M08 BI DIRECTIONAL CONTROL 7 M09 VEHICLE INFORMATION Monitoring Test Results o 1 If communication wih the vehicle is established successfully the menu above appears Select MONITORING TEST RESULTS If no menu like picture above is displayed or communication cannot be Lobe established check the vehicle condition and the connection status of the diagnostic connector again In addition check if your v
30. ice is normal You can use saved data and upgrade the diagnosis program by connecting the product to your PC with wire or wireless You can change the sound effects and display unit of the AUTO 1 700 Provides the LCD brishtness adjustment function You can check the latest data and update it automat cally Support real time screen printing function by wireless gt Support Log Data function to save send the data in the case of communication error so that fast customer support and newest communication s available Support remote assistance for usage of product by connecting PC and scanner with USB connector mj CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 2 Product Specifications Dimension 200mm 180mm 40mm Weight 1 32kg 2 911b CPU O Windows CE 6 0 Diagnosis Cortex M3 120Mhz Main Cortex A8 1Ghz Memory 32GB Micro SD Display 7inch Touch LCD 1024 600 Operating Temp 0 45 32 113 F Storage Temp 20 70C 4 158 F Protocol All Flexibility Dual CAN 2 0A 2 0B Singlewire CAN ISO914 2 KWP2000 J1850P J1587 K L line High Speed Serial Flashing Code Ethernet Button Power button All touch button Operating Voltage BV 35V Please note that if AUTO i 700 has been under 0 C 32F it has to stay in room temperature over 2 hours surely before using it over OC If AUTO 1 700 moves from low temperature to room temperature condensations insid
31. icle like the picture above Press the ENTER button to check system information in detail 74 CARIAN INTERNATIONAL AUTO 700 Chapter 9 Program Download It is necessary to download the vehicle diagnosis program to your product in order to use it if here 1s any update due to a new model system or development the program should be updated to the latest one Also the latest firmware and PIC data are provided for update to ensure the best performance of your product For this update the dedicated program is needed The following describes how to install the program 1 How to Install download program Use only the USB supplied by our company to connect the PC and AUTO I 700 Select the DOWNLOAD button in main screen of AUTO 1 700 Download new software after check how to download it in our website Website http www carmanit com In the future you may download a software automatically via Wi Fi without connection of cable Soon we will make a notice in our website after completing development Please contact to where you purchased about downloading latest software 19 CARIAN INTERNATIONAL AUTO 700 Appendix Registration We explain how to register using windows 7 How to register You can register on website or where you purchase our products Website address for registration http www carmanit com How to register through website 1 Input http www carmanit com into theaddress bar on br
32. ion check if your vehicle supports OBD II communication 64 CARMAN INTERNATIONAL AUTO i 700 Chapter 8 OBD II EOBDVehicle Diagnosis EN OBD2 EOBD CAN OBD II 16PIN CONNECTOR SENSOR VALUE Fuel System 2 Status Calculated LOAD Value Engine Coolant Temperature Short Term Fuel Trim Bank1 Long Term Fuel Trim Bank Short Term Fuel Trim Bank2 Long Term Fuel Trim Bank2 Intake Manifold Absolute Pressure Engine RPM 0 0 rpm 0 0 0 0 Graph Mode File Mode Dual DTC Guide Info Change Unit PP OBD H EOBD LIVE DATA 2 2 Sensor data are listed on the screen as shown in above figure you can check values of each sensor em Refer to the description from Chapter6 vehicle diagnosis for each button s function Live data items in OBD II communication may be different from live data items that are checked by selecting cars because live data itemsin OBD II standard are provided 65 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBD Vehicle Diagnosis 3 Diagnostic Trouble Codes Press this button to check trouble code of current vehicle D SE 1 M01 READINESS TEST 2 M01 PARAMETER DATA 4 M04 ERASE RESET DTC 9 M06 MONITORING TEST RESULTS 6 M08 BI DIRECTIONAL CONTROL 7 M09 VEHICLE INFORMATION DTC selection 3 1 Communication withe vehicle is properly establlished the above menu appears Select Diagnostic Trouble Codes If the a
33. ition If the ignition switch is placed in the OFF position power cannot be feed to the ECU and the diagnosis with AUTO 1 700 cannot be performed 60 CARMAN sa AUTO i 700 Chapter 7 OBD II EOBDDiagnosis Menu 5 1 Communication screen Communication 5 2 Connect a OBD2 16pin connector DLC main cable Connect OBD2 16pin connector ee Te ee 61 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 1 READINESS TEST The readiness test tries making communication with your vehicle to review general items of ECU modules that response A 1 M01 READINESS TEST M01 PARAMETER DATA M03 DIAGNOSTIC TROUBLE CODES M06 MONITORING TEST RESULTS M08 BI DIRECTIONAL CONTROL 2 3 4 M04 ERASE RESET DTC 5 6 7 M09 VEHICLE INFORMATION Readiness Test Selection ak If communication with the vehicle is established successfully the menu above appears Select READINESS TEST If no menu like above is displayed or communication cannot be ESP established check the vehicle condition and the connections status of the diagnostic connector again In addition check if your vehicle supports OBD II communication 62 CARMAN INTERNATIONAL AUTO i 700 Chapter 8 OBD II EOBDVehicle Diagnosis EN OBD2 EOBD CAN OBD II 16PIN CONNECTOR SENSOR DIAG MENU MIL Status y Misfire Monitoring Supported SUPP
34. ly if user s vehicle has OBD II EOBD 02 Car Commercial Bike This menu provides scanner s own functionality such as vehicle diagnosis service data search actuator activation etc Depending on your option you can perform diagnosis on Korean Japanese European Australian and USA vehicles 03 Download In this menu AUTO 1700 can connect to PC so that it can upgrade software and download saved files etc in AUTO 1 700 to PC 04 Config In this menu you can check the system display unit favorite maker setting screen setting time setting and system information 05 Utility In this menu you can check flight record saved list captured screen etc 06 Repair Later it will be supported on our website BEE 26 carmnw INTERNATIONAL AUTO i 700 Chapter 2 Menu Configuration 3 Icons on Main Screen 3 1 Icons on main screen D D 1 Clock This displays the current time 2 sound It can sound on off by touch 3 Battery Status Charging status This indicates external DC power is being supplied and your battery is being charged at the same time 8 Battery status It shows power remaining on your battery After charging the battery use AUTO 1700 in order to avoid discharging 2 CARMAN sa AUTO i 700 Chapter 2 Menu Configuration 3 2 Icons on the CAR menu YUNDAI USA oO RENAULT SAMSUNG EUROPEAN L SEET SSANGYONG Setting 1 Setti
35. month for 24 hours CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 4 Component List 1 Basic kit I 6 CB CYTP 0004 AC DC Power Cord a BEE SE 10 BEE CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 5 Cable Component 1 Korean kit 6 CB AYVG 0007 SSANGYONG ADAPTOR 20P SAMSUNG NISSAN ADAPTOR 14P eme maen lemer Ria LESS cABLE 2 Japanese kit REESEN e op avve 0o08 _NISSANADAPTOR GAP uo mem a2 CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 3 European kit e opavve ooa Opel Adapter aan 4 USA Australian kit CB CYHC 0031 Ford Cable 20P CB CYVG 0009 Holden Capi 10 CARMAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 6 Component Figures and Descriptions 6 1 User Guide AUTO i 700 User Guide j 9 E AUTO 1 700 User Guide Be sure to read the guide before using the product 6 2 Main Module AUTO 1 700 Main Module The exterior might be changed without any notice in advance 11 CARMAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 6 3 Connectors and Key Connectors on upper right side Connectors on upper left side 1 Power connector It is for a AC DC power adaptor and a cigar jack 2 Gas analyzer connector It is for the gas analyzer that Carman International sells The gas analyzer sells separately
36. ng Press this button to turn on off Show DLC Message Box and Log on functions If you select one button the button is brighten and activated 2 Capture Press this button to capture a screen and save it 3 Home Press this button to return to the main screen 4 Back Pressing this button to return to the previous screen 5 Autoselect Car Menu Press this button to Activate then the color of icon changes to white Activate Autoselect Car Menu and AUTO 1 700 starts from the Menu screen directly That is the Main screen is skipped 6 Show DLC Message Box Activation makes the color of icon white Activate this button to show how to connect when select connectors Page39 On the other hand if you do not activate this function you can skip a step of how to connect Chapter 3 Configuration a qo er 28 CARMAN sa AUTO i 700 1 System Display Unit In this menu you can change the display unit of data which are sent from a vehicle The units of various information such as speed temperature pressure angle air flow and sound can be checked and modified System Display Unit System Display Unit 1 1 Itis possible to change the display units all at once according to the region that uses Metric or Yard Pound system 1 2 After changing the display unit click the Save button to save your modification Nae SPEED You can change between Km h and MPH TEMPERATURE Y
37. nto the product The product can be severely damaged Please check if there is short circuit through communication connectors of OBD II or a vehicle in the case of flooded cars It can cause damage of scanner Be sure ot use the USB cable supplied by Carman International only Otherwise your PC or product can be damaged Wireless update or wireless communication requires no hurdle between scanner and wireless devices Also it is recommended to communicate within 10 km CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 1 Product Features AUTO 1 700 can check vehicle ECU information and malfunction status through the OBD II EOBD and CAN communication You can connect AUTO 1 700 to the vehicle diagnostic connector with a diagnosis cable to check if any of the engine automatic transmission ABS air bag power steering and other devices has an error view current data and use actuator drive features AUTO 1 700 has the following features Diagnoses Korean Japanese and European vehicles Support OBD IVEOBD MOBD Support CAN SAE J1850 ISO9141 2 KWP2000 J1587 gt Supports vehicle troubleshooting and current data search You can diagnose vehicles with their sensors and switches and save and reload the current data gt Supports automatic actuator inspection This function runs stops the actuator and switches forcibly in order to check if the corresponding active dev
38. ol circuit open aa m ERC ef ENK Ba 3 1 DTC Press this button to check current DTCs In the case of MIL type vehicle you can check codes through the DTC list 3 2 History DTC Press this button to check old DTCs 3 3 Erase DTC Press this button to clear DTCs 3 4 Freeze Frame Press this button to check data at that moment of malfunction 3 5 Detail Press this button to display detailed information for DTCs 3 6 Recheck Press this button to check for DTCs again The module checks the ECU information again for DTCs Press DTC and History DTC buttons again 44 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 2 Erase Reset DTC l If you select a car and a system correctly on the menu and if communication with a car works successfully it shows the DIAG MENU like a picture below Press the ERASE RESET DTC button DO YOU WANT TO ERASE Y N CONDITION KEY ON ENGINE OFF MISFIRE DELAY RESON SYSTEM INFORMATION ERASE RESET DTC 2 You can see Yes amp No buttons If you choose the YES button the DTC is deleted If you choose the No button it returns to previous step There are current and old DTCs When trying to clear old DTCs they KO are cleared immediately and they are not set again However when trying to clear current DTCs they are cleared for a short period of time but they are activated again In this case clear DTC
39. ot available it is required to be repaired Q The touch screen does not function properly A 1 The touch screen coordinates may not be correctly aligned It is possible to test the touch screen coordinates by selecting the CONFIGURATION from the main menu and then selecting DISPLAY and Test Touch Coordinate menus in order If the coordinates are not correct correct them using the Calibrate Touch Screen function If the problem is not solved a hardware of scanner or a vehicle may be out of order If so the scanner requires to be repaired 71 CARIAN INTERNATIONAL AUTO 700 Certificate of Information and Communication Equipment Certification Label for Information and Communication Equipment Manufacturer Carman International Co Ltd Equipment Vehicle diagnosis device Model AUTO i 700 Manufacturer ID MSIP REM CMi AUTO 1700 Certificate Date Aug 2014 COPYRIGHT by Carman International Co Ltd All right reserved No part of this publication may be reproduced stored in a retrieval system or in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of the author 78 CARIAN INTERNATIONAL AUTO 700 WARRANTY CARD Warranty Policy 1 The manufacturer warrants this product to be defect free in material and workmanship for a period of one 1 year from the date of purchase Defective products may be returned by the original purc
40. ou can change between C and F PRESSURE You can change among mbar kPa inHg and ps ANGLE You can change between and AIR FLOW You can change between gm s and Ib m SOUND It can be turned ON or OFF Chapter 3 Configuration mj 29 CARMAN INTERNATIONAL AUTO i 700 2 Maker It is possible to select your favorite vehicle maker to be displayed on top in the diagnosismenu This function can save time to search for the desired vehicle maker whenever the diagnosis is made From the left menu uk select your favorite brands Your favorite brands will be appeared at the top of the vehicle diagnosis menu If you do not select a brand vehicle diagnostic menu will be appeared in alphabetical order Favorites menu items and Maker 2 1 Maker Please select a maker and click the save button then please click the confirm button 2 2 Initialization of favorite It initializes the saved favorites Please click the initialize favorite button and confirm to save changed settings The list of makers shows some models that s not included in what you Lobe download You can check valid model in the menu of the car or the commercial car on main screen Chapter 3 Configuration 30 CARMAN sa AUTO i 700 3 Dispaly You can set up language and brishtness of LCD Setting brightness will improve efficiency of work in a dark or bright pla
41. owsers 2 Refer to the JOIN page in our website 70 CARIAN INTERNATIONAL AUTO 700 Q amp A Q Communication cannot be established A 1 Check the connection of the diagnostic cable Communication cannot be established if the diagnostic cable is not perperly connected Some old vehicles may have a problem on pin of DLC 2 Check if power is properly supplied to the main module Vehicle diagnosis can be affected by unstable power source You need to check power from battery or from DLC connector If the vehicle diagnostic cables cannot supply power from vehicle connect the cigarette lighter power cable for power If there is electric potential difference between AUTO 700 batteries and vehicle batteries communication is not available If the problem is not solved a hardware of scanner or a vehicle may be out of order If so the scanner requires to be repaired Flooded cars may be not communicated also it will cause damage to your scanner So Check if there is any short circuit in advance before scanning the flooded cars Q I cannot turn on the module A 1 Check if the battery in the module is charged The built in battery may not be charged 2 The battery may not be able to function due to the ambient temperature Avoid excessively hot or cold areas 3 If battery life is over booting by battery is not available If DLC cable cigarette cable or AC DC adapter cannot supply power and booting is n
42. power can be supplied through the diagnostic connector 1 Korean kit SAMSUNG NISSAN ADAPTOR 14P KIA ADAPTOR 20P BLUE DAEWOO GM ADAPTOR 12P SSANGYONG ADAPTOR 14P SSANGYONG ADAPTOR 20P 18 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions i DAEWOO LPG CABLEHYUNDAI MITSUBISHI CABLE 12P 2 Cable for registering trans meter codes to Korean vehicles KIA KEYLESS CABLE HYUNDAI KEYLESS CABLE 19 CARMAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 3 Japanese kit TOYOTA LEXUS ADAPTOR 17P R TOYOTA LEXUS ADAPTOR 17P C HONDA ADAPTOR 8P HONDA ADAPTOR 5P SUBARU ADAPTOR 16P 9P MAZDA C ADAPTOR 17P MAZDA ADAPTOR 6P 1P NISSAN ADAPTOR 14P 20 CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions MITSUBISHI ADAPTOR 12P MITSUBISHI CABLE 12P 16P 21 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions 4 European kit ah Mercedes Benz Board 38P Mercedes Benz Cable 3 liners O PSA Cable 2P Audi VW Cable 2 2P Fiat Cable 3P Opel Adapter 10P BMW Adapter 20P 22 carmnw INTERNATIONAL AUTO i 700 Chapter 1 General Descriptions 5 Usa Australian kit Ford Cable 20P Holden Cable 6P 23 CARIAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 7 Power Supply 1 Cigarett
43. rometric Pressure Sensor P2122 TPS APS1 Signal Low P2127 Accelerator Position Sensor 2 Signal Circuit Low Input ES P2104 Limp Home Mode Forced Idle SYS INFO P1295 Limp Home Mode Power Management P0222 Throttle position TP sensor B accelerator position APP sensor B low input Graph Mode File Mode Dual DTC Guide Info Change Unit Dual DTC Press the DTC list button to exit the dual display mode and return to the Record Data Viewer In the Dual DTC mode Press the Text shot button to save DTC and Nae sensor data 50 CARMAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 4 ACTUATOR TEST In this menu you can start and stop actuators and switches forcibly to diagnose them The actuation function is available depending on vehicle makers and models cU 1 DIAGNOSTIC TROUBLE CODES 2 ERASE RESET DTC 3 PARAMETER DATA 4 ACTUATOR TEST RESETTING ADAPTIVE VALUES EVAP LEAKAGE TEST PCM LOCK MEC SETTING MISFIRE DELAY RESON SYSTEM INFORMATION Actuator Test 1 If a car and a system are selected correctly in the Vehicle Diagnosis menu and communication with vehicle is stable the above picture will be shown Select a Actuator Test If above picture is not shown the communication error appears or communication does not work check again the status of vehicle and kr connection of cables for diagnosis 51 CAR
44. roperly 2 If you conclude that a real problem exists check your product according to the procedures on the Trouble Shooting Card and mark your trial records in the blank 3 Please return the main body or the troubled parts along with the Trouble Shooting Card to the repair service center listed below Be sure to return them in freight prepaid as we don t accept freight collect Carman International Co Ltd 1210 12th Floor Hoseo Univ Venture Tower 70 Gasan digital l ro Geumcheon gu Seoul 153 711 Korea Teli 62 72 2602 403040 Pax 62 2 602 4951 Email service carmanit com Homepage http www carmanit com 79
45. s again after checking and repairing malfunction parts for the corresponding DTCs 45 CARIAN INTERNATIONAL AUTO 700 Chapter 6 Vehicle Diagnosis 3 Parameter Data In the PARAMETER DATA menu the module can communicate with the vehicle ECU to check data and control values of each sensor of the selected system and to check conditions of various switches and actuators It is important to select the vehicle specifications correctly for accurate Lobe sensor data measurement Make sure to set the vehicle displacement manufactured year fuel etc correctly The live data list can differ even with the same vehicle models EN HYUNDAI KOREA DOMESTIC Veracruz Engine Gasoline OBD II 16PIN CONNECTOR ER 1 DIAGNOSTIC TROUBLE CODES Hoo 2 ERASE RESET DTC 4 ACTUATOR TEST 9 RESETTING ADAPTIVE VALUES EVAP LEAKAGE TEST PCM LOCK MEC SETTING MISFIRE DELAY RESON SYSTEM INFORMATION Parameter Data Selection NOTE The menu for Parameter data selection shown in the above picture can differ by vehicle makers and models 1 When selecting the correct vehicle model and system from the menu and communication with the vehicle s properly established the menu appears as the picture above Select Parameter DATA and press the ENTER key If the message indicating a communication error is displayed instead Lobe of the menu like the figure above or communication cannot be established
46. ttery of a vehicle directly by connecting to a cigarette cable CNRMNAND INTERNATIONAL AU TO i 700 Chapter 1 General Descriptions 6 12 DLC Cable DLC Cable The DLC cable is also called the OBD II cable All vehicles released recently have built in OBD II connectors compatible to the OBD II specification It is possible to diagnose new model vehicles by directly connecting the DLC cable It is not necessary to connect any additional power source as power is feed through the diagnostic connector Old model vehicles should be diagnosed by connecting an additional kr 6 13 AC electrical power cord adapter adapter AC electrical power cord adapter When you want to download the diagnosis program or search flight record you can use this AC DC electrical power adapter to feed power Also can charge the battery built in the product 17 CARMAN INTERNATIONAL AUTO 700 Chapter 1 General Descriptions 6 14DLC Adapter The DLC adapter is used to diagnose vehicles by connecting it to the DLC main connector As there are similar shaped adapters make sure to check the vehicle manufacturer name on the adapter before use Also there can be various adapters for one manufacturer Therefore be sure to check the shape and pin numbers of the diagnostic connector in the vehicle Some vehicles do not supply power through the diagnostic connector CAUTION Do not connect any power supply if
47. vehicle condition and the connection status of the diagnostic connector again In addition check if your vehicle supports OBD II communication 72 CARIAN INTERNATIONAL AUTO 700 Chapter 8 OBD II EOBDVehicle Diagnosis 7 VEHICLE INFORMATION This menu displays information of the ECU installed in your vehicle You can check only the ECU that provides its module information This menu displays information of the ECU installed in your vehicle You can check only the ECU that provides its module information M01 READINESS TEST M01 PARAMETER DATA M03 DIAGNOSTIC TROUBLE CODES _ M04 ERASE RESET DTC M06 MONITORING TEST RESULTS 6 M08 BI DIRECTIONAL CONTROL 7 M09 VEHICLE INFORMATION VEHICLE INFORMATION Selection 7 1 If communication wih the vehicle is established successfully the menu above appears Select Vehicle Information If no menu like picture above is displayed or communication cannot be Lobe established check the vehicle condition and the connection status of the diagnostic connector again In addition check if your vehicle supports OBD II communication 73 CARMAN so AUTO i 700 Chapter 8 OBD II EOBDVehicle Diagnosis co 0 OBD2 EOBD CAN OBD II 16PIN CONNECTOR TXT ajaja ajaja ajaja IAG MEN DTC ATA ADAPTATION This menu displays information of the ECU installed in your veh

AUTO-i 700 Manual

Contents

Download Pdf Manuals

Related Search

Related Contents