Manual of Program Card Doc Ver. -02-090103.1
Contents
1. model is power on 0 means the cut off function is disabled For example 10 cell NiMH battery fully charged voltage is 1 44 10 14 4V when Medium value is selected the cut off voltage is 14 4 45 6 5V 5 Music Li Po Cells The 4 LEDs have different meanings for ESC with or without a postfix letter of HV For ESC without a postfix letter of HV for example Pentium 60A 4 LEDs have 16 possible states representing 16 rhythms for ESC The ESC will play the music when it is started Please refer to the Table 1 in the next page For ESC with a postfix letter of HV for example Pentium 90A HV 4 LEDs 10 0 70 10 iO 1O t0 10 0 iO O 20 FO tO FO 10 10 O IK Doc Ver 02 090103 1 represent the number of lithium battery cells Please refer to the Table 2 in the next page WIRING SEQUENCE A When you are using an ESC with a built in f yn J BEC Battery Elimination EKI A Circuit eatery E ani z F Speed i i Controller WV 1 Disconnect the main power pack from the ESC o j i Da 3 T 4 Cut Of pall Middle 5 Start O Mode Soft I ice Mode Middle 7 Music iPoCals c 8 Governor Mode ON gt Load De Receiver Battery Pack 3 Connect the main power pack to the ESC 4 The LEDs on the program card will light to show the current programmable value2. ESC When the data transmission is finished the blue LED will stop flashing it means the new settings are accepted and stored in the ESC MUSIC LIST Table 1 Music list LED is lighting Doc Ver 02 090103 1 LI PO BATTERY CELLS NUMBER LIST Table 2 Li Poly cells number list LED is lighting Li Poly Cells Number afede p efe pee o fe fo fe ws ooo ess MES e fo fo fe e ase Ps fo fe o o smsem e o e o o femsem r o e e o reuse re fofe efo pasew re fe o o o jecusme o e o o o jwcuseo Pepe ole o pesem Pepe ole e jrcusmm Pepe fe o o awa ree fe o e ws re fe fe e ws re fe e e ofws We strongly suggest manually setting the cells number of your lithium battery pack Please be careful to use Auto detect method DECLARATION This program card is ONLY suitable for the ESC made by the same manufacturer Please ask your retailer for detail product information
3. Manual of Program Card USER MANUAL OF PROGRAM CARD Thank you for purchasing program card for the brushless motor electronic speed controller ESC With this device you can easily set the programmable value of the ESC Now you can just forget the complex and boring program method with the throttle stick of your transmitter This program card has a friendly user interface It is as small as a business card so you can put it in your pocket when you are on the field SPECIFICATION 1 SIZE 92mm 52mm 6mm 2 WEIGHT 26g Batt BEC FRONT PANEL 1 Use up down button to select the programmable item use left right button to select each item value 2 Brake When Brake is ON the motor will be stopped immediately when throttle stick is moved to bottom 3 Low Voltage Protection Mode Cut off Type When Soft Cut is selected the ESC will gradually reduce the output power When Cut Off is selected the ESC will immediately shut off the output power to the motor 4 Low Voltage Protection Threshold Cut off Voltage e For Li xx battery Li ion or Li poly the number of battery cells are calculated automatically Low Medium High cut off voltage of each cell is 2 6V 2 85V 3 1V For example 3S Li Poly when Medium cutoff voltage is set the cut off voltage is 2 85 3 8 55V For Ni xx battery NiCd or NiMH Low Medium High cut off voltages is 0 45 60 of the initial voltage when the
4. s of the ESC NOTE1 THE SEQUENCE OF STEP 2 AND STEP 3 CANNOT BE REVERSED Otherwise the program card cannot work properly B When you are using an ESC without a built in BEC If the ESC is marked with BEC OPTO that means this ESC hasn t a built in BEC so you must use an additional battery pack 4 8 6V to power the program card and usually a receiver battery pack is a good choice 1 Disconnect the main power pack from the ESC 2 Disconnect the BEC cable trio wires of the ESC from your receiver and then connect it to the program card at the top right corner position marked with BEC 3 Connect the receiver battery pack 4 8 6V to the program card at the top right corner position marked with Batt 4 Connect the main power pack to the ESC 5 The LEDs on the program card will light to show the current programmable values of the ESC NOTE2 THE SEQUENCE OF STEP 2 STEP 3 AND STEP 4 CANNOT BE REVERSED Otherwise the program card cannot work properly Manual of Program Card NOTE3 Don t use a battery pack higher than 6V to supply the program card OPERATION Press the up down button you can select the programmable item the corresponding LED will flash Then press the left right button to select the item value the flashing LED shows the value you are just selecting Finally press the OK button the blue LED will flash which means the programmable value is being transmitted to the
Download Pdf Manuals
Related Search