SimView
Contents
1. Figure 69 You can find the Component Service by typing it into the Start menus search field Q Something went wrong during recording and now cannot see my simulations A The simulation may not have been save in the debrief session after the recording was stopped In the Server setting tab you can use the Unsaved simulations button to see simulations that have not been save by mistake You can view the simulation and then save it or if you want delete it Q can see my simulations on the SimView Server PC but the video is frozen on my Instructor PC A If the number of video cameras incl the patient monitor is more than 2 some older laptops cannot play the video To solve the problem either reduce the number of cameras or upgrade the Instructor laptop PC to the recommended hardware See the user manual for SimViewer Q Windows was upgraded by the windows auto upgrade now my USB cameras don t work A The USB camera driver has been upgraded and you must remove the camera in SimView and the setup the USB camera in SimView again Q A USB device will not start It used to work A Please remove it from the device list and add it again If it still doesn t work try to move it to a different port Q My USB camera is having issues working properly even after trying to move it to a new port and reconfiguring it A Make sure the newest drivers are installed 35 Q Why is the Instructor app referring to AV2. Add Cancel Events Drugs Events Drugs ee N oe L Obtain 12 lead ECG Amrinone Attach 12 lead ECG Atenolol Atropine Remove 12 lead ECG Attach 3 lead ECG Captopril Diltiazem Remove 3 lead ECG Dobutamine Abort attempt Dopamine Attach ABP sensor Enalapril Remove ABP sensor Ephedrine Apply ECG leads Epinephrine Apply ECG monitoring Mesecs PAM ao saibe nimmu Fece tet Search Figure 64 The different comment windows Add Edit Add Edit Time 00 02 08 Time 00 02 08 o 2m ss on 2m s Atropine gt Attach 12 lead ECG gt IV IO bolus v Will unset Remove 12 lead ECG Dose 15 mg Comment Comment Add Cancel Add Cancel Figure 65Adding a drug or an event When you have added the comment for the student you can export the session for use with the SimViewer and at the same time free the local hard disk space for new simulations by deleting the file You can now only see the simulation with SimViewer as it will not be visible in the SimView home screen The exported files can be put anywhere incl on a USB thumb drive 32 7 Maintenance 7 1 Backup strategy Video files take up large amount of hard disk storage so a strategy for how to save the simulations for later use is needed The main use of SimView is to record the session and do the
3. T Recent Places No items match your search d G Libraries C Documents a Music Pictures E Videos v File name Asthma pdf E Save as type Adobe Acrobat Document 7 Figure 56 Saving the print file x Asthmal2 paf Adobe Reader HAasZaea b 2 O gt Ble 2 ie Tools Sign Comment 5 z Time and Date 43 05 21 2012 12 19 a Simulation Activity Name Asthma basic Co Sim Manikin type SimMan3G a SimView name test Event Log 00 00 Recording started 00 01 Log file created 00 02 Add new logitems to the log by hovering these logitems 00 20 Recording stopped Figure 57 The print file showing the Event log 28 6 9 Sharing simulations There is more than one way to share the simulation recordings with the participants If the participant has an account on the SimView Server then the person can just log in on the SimView server from any PC on the network using an internet browser i e Internet Explorer or similar If the participant does not have an account on the SimView Server then you have two ways of sharing the simulation either export the file to a thump drive or send a link to the simulation e You can make a private link for sharing the simulation with others without exporting it You can then send this link to the person you want to share it with The person will only be able to see this simulation and nothing else and will not be able to use other feat
4. Use no camera C Use web camera Start Scenario Editor F Start Handler Editor Start Trend Editor Web camera recording Medium Configuration Microphone Configuration Video server recording Video Recording Configuration Video server name 192 168 1 100 Set Vital Signs 7 Camera 1 Korotkoff Controls Camera2 The IP address for the PC running the Camera 3 Instructor Application Camera 4 Patient monitor recording 7 Enable monitor recording Quality Medium X Recording time Maximum recording time 30 minutes Monitor source identification for Video Client Monitor name ihilli Port 5001 Cancel Figure 7 The SimMan setup Tip If you experience connection problems between the Instructor Application and SimView after the setup make sure that the Laerdal SimView Extension Service is started and configured properly You can check by using the Component Services tool go to the Start menu and write services in the search field select the Component Service Under the Services Local you should see Laerdal SimView Extension Service if the status is not running then press the Start button in the top left side of the services listing You can also use the SimView Extension to check the connection and the service as both will be checked when the Test connection is used 5 SimView 5 1 Software installation The SimView server PC will be supplied wi
5. 8 The IP Address of this device Add equipment IP aadress 192 168 119 43 x Port 5001 Save changes Tip Remember that the Patient Monitor is regarded as one of the maximum 4 cameras that can be used during recording In order to enable Patient Monitor recording you must setup the SimView Extension service and enable it in the Instructor Application see chapter 4 5 and 4 6 on page 7 5 2 10 Analog camera Adding an analog camera follows the same line as the USB camera but requires that the PC is equipped with a Laerdal video grabber card If you have more than one camera select the with the drop down list 6 Equipment configuration Equipment configuration Equipment configuration admin Log off Devices Select device to add Figure 35 Devices Select device to add IP Camera Usb Camera Microphone Patient Monitor Analog Camera Figure 36 Devices Select device to add IP Camera Usb Camera Microphone Patient Monitor Analog Camera Figure 37 1 LIVEVIEW amp SETUP ff HOME E Laerdat Heotrserean 2 Add equipment Add equipment Add equipment Add equipment Add equipment Add equipment 20 V Equipment configuration Add equipment Devices Analog Camera v Found devices 1 m Figure 38 6 Using SimView Server With SimView you can record simulation sessions and annotate the vide
6. Devices 3 Select the Patient Monitor by clicking in the list window 4 and 5 Insert the correct IP number in the IP address 6 field the other fields are pre filled and should not be changed Click the Add equipment 7 Add equipment Add equipment Add equipment Add equipment Add equipment 7 gt Add equipment Add equipment ca QP seve choos If you want to change the IP address later enter the new address in the field 8 Press Save changes 9 9 Later changes in IP address can be done by changing the address in the address field 8 and save changes ye A ty ta a Liveview amp SETUP f HOME ZB SimView ar OM Jaton Esser admin Log off 2 taerdat Heatthserean V Equipment configuration 2 Devices Select device to add v Add equipment Figure 30 V Equipment configuration Add equipment Select device to add IP Camera Usb Camera Microphone Patient Monitor Analog Camera Figure 3 V Equipment configuration Select device to add IP Camera Usb Camera ou want to add Microphone J Patient Monitor Analog Camera Figure 32 V Equipment configuration Add equipment Devices IP address Patient Monitor v 192 168 119 43 x 66 Hre Figure 33 Equipment configuration a Patient Monitor V Active Name Model name Patient Monitor Figure 34 r
7. Healthy patient ged Patient SimMan Share private link Delet Participants oe added No participants added Bed tewornes Instructors No instructors added No instructors added Figure The Home screen and options for simulations Select the simulation to watch or delete by clicking on the link below the picture When you have selected the simulation by clicking on the picture you have 3 options if you click the triangle in the bottom right corner e Export the simulation for stand a lone use with SimViewer or for backup purposes e Delete the simulation if it is not relevant anymore and for freeing up space on the hard drive e You can make a private link for sharing the simulation with others without exporting it You can then send this link to the person you want to share it with The person will only be able to see this simulation and nothing else and will not be able to user other features of SimView The person that gets the link must have access to the PC with SimView but does not need a SimView account to see the simulation The access via this link will be restricted to only this one simulation Note Only delete simulation files using the SimView Home screen or by using the facility under Server settings View recovered simulations 5 2 4 Video file sizes The hard disk storage needed for video files depends on the resolution and frame rate AXIS camera file sizes 1280x720 25fps 30MB min 800x450 25fps 1
8. see Figure 9 Error Reference source not found If the address is not present only Laerdal support will be able to help Add the address in the filed SMTP server and press Save changes In the server setting pane you can also add a server name and the directory for saving the simulations if nothing is entered for the Working directory the default C Avsfiles will be used 5 2 3 Server settings Storage Since SimView Server handles video files in high quality the system will run out of space eventually and it is important to actively decide on whether older simulations should be backed up or simply deleted A backup strategy must therefore be made on how to store old simulations and prevent data loss in the event of a hard disk failure The data storage strategy can be set in the server settings frame See Figure 9Error Reference source not found Simulations can be exported to external disk storage by using the export function When exported they are also ready for use with the SimViewer application The need for space depends on how the video quality is setup The use of full HD video takes up much more space than normal VGA video but the quality of the video may be sufficient for many purposes The server settings only offer the possibility to delete by date If this is not what you want you will have to manually export or delete files To do this go to the home screen Q Advanced search LEE 11 50 2013 Jan 25
9. Create button 6 Close the input window by clicking the VIEW amp SETUP button 1 ot os oS o Sim r admin Logout 3 Laerdal HeotthSerean amp HTT 00 00 Equipment configuration Add equipment Server settings lt 2 2013 SimVentures All rights reserved Version About 8 Figure 8 Server settings General Disk Usage System notifications Server name Available disk space SimServer Ganr 56 No notifications Working directory 105 GB free of 239 GB DAAVSFiles Automatic clean up options zki V Delete data that is older than 90 days nos al Run automatic dean up now View recovered simu lations User administration 3 SimView system erro SMTP server Save changes 9 Figure 9 User name Nurse Karen Email address lt 4 k l dk Password User type Administrator User 5 a cea lt 6 All fields are required Figure 10 The user creation window The difference between the Administrator and the User is in what they can do with the system The administrator can record change the configuration of the system regarding number of cameras etc and edit the event log in the simulations by adding comments the normal users can only watch simulations 5 2 2 Server settings General Under server setting the address of a SMTP mail server can be added in order to get a mail with a password reset in the event that someone has forgotten the password it
10. Note The Patient Monitor is counted as a camera and is included in the maximum of 4 cameras that can be used for recording 6 6 Controlling SimView from the Instructor Application When using the SimView Server together with the Instructor Applications like SimMan3G there are a few things to observe in order for everything to work as expected Apart from the setup described in the administrator manual there are thing to observe when starting and stopping the recording sessions Always start sessions from the file menu Start new session then press the Start session see green marking When stopping the recording session use the End session In the pop up window you have 3 choices Quit Start new session or Debrief never use the Save session as it does not work with SimView Server To save a simulation session go to Debrief and save it on the SimView page that show up in your web browser 00 00 02 00 00 05 00 00 08 AVS video recording started NBP cuff attached Head ECG attached Restart session Load session Go to DebriefViewer Transfer media files Exit End session Figure 50 Tip Only use the options marked with green boxes SimMan 3G Version 2 3 ver _4 End Session Do not use with SimView a Start Auto Mode Start Instructor Mode Open previously Patient Case Scenario saved session Currently conne
11. SimView Server or the PC from where you are doing the export Share private link x Share private link x You can share a private link to this recording Anyone with this link will be able to view You can share a private link to this recording Anyone with this link will be able to view this Simulation Activity as long as they have access to the SimView network This link this Simulation Activity as long as they have access to the SimView network This link only gives access to this specific Simulation Activity and will not require a login to only gives access to this specific Simulation Activity and will not require a login to SimView SimView htto simviewserver1 80 SimView Simulation Datai 4 6904 952d d387264ci Sse token 57580C10413F5848587386B603AEF113 token 57580C1D41 Open How to use this link Right click on link and select Copy Then open your mail client and paste this link in How to use this link Right click on link and select Open in new tab the mail body the Open in new window A right click will n this window pata side j do Save target as n aoaaa Otte N E Print target Instructors No instructors adde Copy shortcut When using a web based e mail accouft2 F gt SimVventuy select this else use esson V2 0 the copy shortcut 2 E mail with Windows Live function and your e mail client ay Translate with Bing All Accelerators Add to favorites Properties Figure 61 Sharing a link to a sim
12. SimView server must use their own Windows Domain account as the browser will remember passwords to SimView e All instructors using the system to record from an Instructor PC should have their own SimView user account and Windows account and not share a single account on this PC These points may not be interesting to your site if access to the SimView Server is physically limited and you value ease of use higher than strict security 3 6 Axis IP Cameras The cameras supported by SimView can be accessed over the network and should be secured with passwords to prevent unauthorized access to the live streaming video Laerdal has no control over this software and rely on the vendor and user to securely protect access 3 7 File security and backup of data The customer is responsible for file security and backup routines for all simulation session data All use and storage of simulation session data should be in accordance with local rules regulations or laws and is the sole responsibility of the customer See more on backup in sections 5 2 2 on page and 7 3 on page 33 4 Setup Note Any USB devices must be setup properly on the SimView Server PC before they are accessible by SimView If you have trouble please check that drivers are properly installed 4 1 Computer name To make it easier to access the SimView Server from other PC s on the network you can give the server PC a name that is easy to remember The PC name is setup in the wi
13. log 29 Do you want to open or save Healthy patient 3G ssx from simviewserver1 Bad Cancel Save Save as Save and open Organize v New folder Date modified Type Tr Favorites BE Desktop Asthma basic ssx B Downloads Healthy patient 3G s l 5 Recent Places BEE Desktop aw Libraries Select and change name and destination to suit your needs l m a Hide Folders Save Cancel L _ o Figure 60 Transferring a SimView recording to another person by using the export function 6 9 1 Exporting a simulation When exporting the simulation you have two options the whole simulation or just one of the video files When exporting the whole simulation it will in SimViewer look exactly as in SimView with all video and event log etc Choosing to export a video file will only show the video from the chosen camera When exporting you have the option to save the file on a USB memory stick thumb drive for use on other PCs even stand alone PCs with no network connection but you can also save the file on a network attached hard drive for use on the local network The PC needs to have SimViewer installed in order to show the recordings 6 9 2 Sharing simulation links Sharing simulation by private links can be done by e mail To use the e mail option you will have either have a Live Mail account or have a mail client with a valid e mail account installed on the
14. no data received when arrive in the morning A Some cameras may give this problem when the images don t change as in darkness try to add an overlay with the data and time this is done in the ASIX camera setup using the operator mode Q Not all of the USB camera settings work A Try a lower frame rate update the driver Disabling the manufactures driver and rely on the Microsoft embedded driver may solve the issue completely Q SimView is not remembering my passwords A Remembering passwords is a feature in the browser you are using such as Internet Explorer or Firefox If passwords are not being remembered it is most likely because of a user actively selecting not to save the password for this site To reset this setting you can try to clear the browser s cache settings or enquire with your IT whether policies are in place to stop you from remembering passwords It may also be because you have used another address for the SimView Server i e shifting between name and IP address 9 Index A list of acronyms used in the document and also links to where to find things PoE Power over Ethernet WiFi Wireless internet WLAN Wireless Local Area Network IP Camera Internet Protocol Camera Ethernet Network type Switch Network switch Firewall System to block unwanted access LAN Local Area Network HTTP Hyper Text Transfer Protocol RTP RTSP DNS Domain Name Server H 264 MJPEG Motion JPEG JPEG Joint Photographic Experts Gr
15. p Laerdal helping save lives SimView The Administrator s Direction for Use Version 2 Contents I WINCROCUCEOfi sta ete eta a tae Ea nee eee 3 Before VOU Stare Ms tall NS roire secs te ohtacs Sasi e sete chtass Seshtace chains cheese Shtes cc Shatsesechcttacs Shateas Sestaccesecttvcediae 3 1 2 Quick installation OVervieW sasira E a E tues AEA es 3 2A COn an Wa AN a e e eeeeT 4 2 Warran Vena a AR dear E E A wteslin badd dw dade awan eases 4 3 Important N te noses a leaded atic ded id shades dated edict deb det a E 4 3 1 SimView Security and Privacy concerns ccscsssccsscecsssscsrsscscsesscessssscsesscsssaseceesecsseesscessssscsesecessasscsesecseeessees 4 3 2 Whose responsibility is it to secure the SIMVIEW Server ou ceessececetseceesececesseceeseceseesecesesceeesseceeeeesees 4 3 5 PMCAVIEUS aNd PineWallS uarnnndkndndnnnnkneaahanninhnkninhnenenkninanhnknaonehaneneknn 4 3 4 PINOY area rae tara asec sees te aes aoe Sessa auc Seas Sau seas tad Seeds aes ta E 4 3 5 Unauthorized access to SimView content seseseessssesesessoresessoresesessoresesesrosesessoresesessoreseserosesesesroseseseereses 5 BO PAIGE CIME aS een e E E EE E E E E EE 5 37 Filesec urity and Dackup or datasseisoeis pope eaea 5 E E E A AE EAE E A OE ARE A AA ER AA RE TAA NE INA TAE A A EA AE E ER 6 4 C mpuUter NaMe eaaa E E E E O I A Tie alde halal s 6 4 2 Microphone instala ON sssaaa E E E E E E E E E 6 4 3 External Audio EGU
16. the SimView chapter 7 3 Hard disk clean up of unsaved simulations If you have unsaved simulations you can delete or save them by clicking the View unsaved simulations under the Server settings tab An unsaved simulation occurs whenever you don t press the save button during the debrief session that is opened after session is ended This saving of the files is to make sure you don t lose any simulations by mistake When you press the Show button at the filename in the Recovered Simulations window you will get the option to save the simulation You can also just delete the simulation if you don t need it Note Any unsaved simulation is automatically deleted after 12 hours 33 An automatic clean up is run every 2 hours but you can run the clean up manually at any time just click at the Run automatic clean up now Message from webpage Lx Please note that this will run automatically and delete all recordings meeting the criteria except recordings marked as favorites OK Cancel Server settings General Disk Usage System notifications Server name Available disk space No notifications SimServer eee 56 Working directory 105 GB free of 239 GB DAAVSFiles l Automatic clean up options SMTP server ES r E V Delete data that is older than 90 days nosm nmal Run automatic clean up now View recovered simulations User administration SimView sy
17. to the PC Connect Web cam if needed to a USB port on the PC Connect the microphone to the PC 2 Cautions and warnings e By using this product Laerdal Medical does not condone the use of this system for violating any government state or local laws or personal rights e This product contains software that may be installed to other computer systems that may allow remote visual and audio monitoring Allowing access to private networks and the recording of unannounced conversations may be a violation of personal rights It is recommended that individuals in the areas of recording equipment be made aware of the installed equipment and to the fact that there conversations and activities could be viewed and recorded without notice e It is not advised to use this system as a means of physical security for the protection of public or private property e Laerdal Medical will not be responsible for loss or stolen property due to the use nor failure of operation of this equipment e Read understand and follow all equipment instructions safety warning and guidelines before operating the Laerdal SimView and all associated equipment e Do not use cables or connectors with bent pins or visible damage 2 1 Warranty Please refer to the enclosed printed Laerdal Global Warranty or www laerdal com for terms and conditions 3 Important Note 3 1 SimView Security and Privacy concerns This document is meant to address concerns regarding SimView p
18. your Instructor PCs Manikins and SimView Server time and date settings are in synch and in same Time Zone Q get an error when starting recording a session that the server in busy unavailable or network problem but the server is not in use and can connect to it with my browser A make sure you have the latest version of the SimView Extension and it is set correctly regarding IP addresses it will check both the connection and that the service is up running severe cases you may have to reboot the Instructor Application PC Q cannot record on the SimView server even as the SimView Extension tests OK A Check if the Laerdal SimView Extension Service is started use the Component Service to check Se Component Services q xX File Action View Window Help _ elx Alo ee BeA n J Console Root Component Services f3 Event Viewer Local 7 a More gt Services Local amp Laerdal Connection Service Provides remote Started Automatic i Laerdal SimView Extension Service Gives supportfo Started Automatic Laerdal Si amp Lenovo Auto Scroll Started Automatic More gt Name Description Status Startup Type Actions IPsec Policy Agent Internet Protoco Started Manual Services L a KtmRm for Distributed Transaction C Coordinates tran Manual S4 Lenovo Doze Mode Service Started Manual z o Extended A Standard i
19. 5MB min 480x270 25fps 6 5MB min 1280x720 20fps 25MB min 800x450 20fps 12MB min 480x270 20fps 6MB mim 1280x720 5fps 2OMB min 800x450 I5fps 10MB min 480x270 5fps 5MB min USB camera file sizes 1280x720 0fps 5MB min 640x480 30fps 15MB min 320x240 30fps 5MB min Analog camera file size 5MB min there is no size options but it looks like 640x480 The sizes are approximate as the motion activity in the picture will change the actual file size the more motion the bigger file size 5 2 5 Unsaved simulations If you by mistake forget to save the simulations during debrief you can find the simulation in the Server setting under View recovered simulations When clicking this link you will see a window with the simulations that for any reason not are saved correctly you will be able to view them and decide if they have to be deleted or you can delete straight away without viewing first Note If during recording the server is switched off by an accidental power cut videos shorter than 4 minutes may not be retrieved and in videos longer than four minutes the timeline and event logs end time shown may be shorter than the actual video recording You may not be able to seek in the video that is beyond this maximum time using the either the timeline or the event log but you can see the whole recorded sequence 5 2 6 IP Camera To add cameras to the simulation setup start SimView and login as Administrator Note SimView only supports AXI
20. 99 00 00 BP 126 84 00 15 SpO2 probe attached 00 00 SpO2 98 00 18 T peri on 00 00 PAP 25 10 00 20 Monitor T blood on 00 00 etCO2 mmHg 34 00 25 N20 on 00 00 Tblood C 37 2222222222222 00 28 00 00 etO2 16 00 30 NBP measured BP 126 84 00 03 AVS video recording started 00 33 Monitor CO2 off 00 05 Attach 3 lead ECG 00 33 Monitor CO2 on 00 06 Attach ABP sensor 00 39 C O measurement 5 6 00 06 TOF 100 00 40 C O measurement 5 6 00 07 Attach PAP sensor 00 41 C O off 00 07 NBP cuff attached 00 52 C O on 00 12 TOF measured TOF 4 99 01 06 Attach capnometer 00 13 Heart rate bpm 78 03 51 testing 00 14 awRR bpm 11 04 09 Cimulntinn andad On ta Dahriaf ____ loi oe Cn nraha ntrachanad Figure 63 The difference between Basic View and Detailed View You can change between the views by using the pull down menu in the Event Log view and then select Basic View Detailed View or Original View Note You cannot edit the event log in the Original View 3 6 10 3 Adding comments to the Event Log If you let the cursor hover over the event list a plus sign occurs and clicking it gives the opportunity to add comments In the window that pops up you may now choose which type of comment you want to insert all the possibilities are show on the picture here Add Edit Time 00 02 08 Add Edit Time 00 02 08 oS zm e6 e Not applicable C Correct C Wrong 3
21. MEN ripen tni Tan Eia T E TRE 6 4 4 USB Webcam IIVSCAN S55 ests oe ciate a E O OE 6 4 5 SimView extension installation and configuration sssessesessesesessssesesessesesesessesesessoresesessosesesessesesessssesesees 7 4 6 Simulator setups for use with SiMViIeW sesessssesessssesessssosesesesresesessosesesessosesessoresesessoresessssoseseseoroseseseereses 8 5 SMVO W e A hae RA R R Whee E A T A E 10 5 1 SOMWANC NIMSCallAGION ricrea naa E E E E 10 FAs CONNUE GO a a ee ee ee ee ee 10 6 WISIN SIM VIEW Servern aa teal cal heat lines tala arate EURAK ANUNTA 21 6 MS TO SINIS Cl OC aden ster tee sducs tee tes e a S 21 62 The POMES EOI Ren ener enn R A 21 6 3 The View Setup Window c ccccs cette cece cre eis E E E alas a atl EE 22 G4A VIGGO WINdOWS sorire nn EEEO RENNE ECONTENT ERT ONO ENTERA 23 6 5 Recording x SCeNIOseneanie ne ienen s e a D E E E T e T E 25 6 6 Controlling SimView from the Instructor Application cccssssecsssscssesssceesecescscecessssesesseceseeseeeseeesseeseees 25 67 Operating thie lP Camera Siuire iiie iE EE TASNIA 26 6 8 DEDENS esoe E 27 62 harne SIMUlat ONS merar a a a a een ee ere ere 29 6A Simulation SESSIONS aaia E T E E ete 3 A MPVANAC SINAN E E E E A A E E E E tench ate hasten cha E tte aun stench E E E 33 7 BACKUD State y ronronner a aa a a aa 33 7 2 What to Dack UD invenis 33 7 3 Hard disk clean up of unsaved simulations cecssesesesseceesscecessecesescecessscesessecesesc
22. S IP cameras From the Home screen click the VIEW amp SETUP 1 l 2 Click the Add equipment 2 3 Click the in the Devices 3 box 4 Select the camera type you want IP or USB to use by clicking on it in the list window 4 and 5 5 Wait while the list of IP cameras is updated see Figure I5 6 Click in the Found devices 6 to get the drop down list and select the desired camera 7 7 Fill in the Login 8 administrator name and Password 9 8 Click the Add equipment 10 9 You can now select the resolution on the video quality by clicking the Resolution 1 drop down list and selecting the resolution you want 10 You can also change the number of picture per second fps by clicking the Fps 12 drop down list I Press Save changes 13 if this was the last camera to add otherwise add a new camera by clicking the Add equipment button 2 again and continue until you have added all the needed cameras I2 You can deactivate the camera by un checking the Active 14 check box and click Save changes 13 If you want to remove the camera from the setup click on the Remove button 15 Equipment configuration Devices i Select device to add vi Add equipment Figure 12 Add equipment starting point V Equipment configuration Add equipment Usb Camera Microphone Patient Monitor Analog Camera Figure 13 Drop dow
23. S system instead of SimVlew A This was the name of the Laerdal AVS software for which the Instructor Applications were originally created Q can t start a recording in the SimView browser even though have stopped and went to debrief in the Instructor application A In SimView browser click reload or pressF5 then you can start a recording from the SimView browser Q The video feed is pixelated or bad It usually looks ok A The IP cameras will need to be rebooted once in a while after heavy use or many concurrent users You can do this by unplugging them from the network cable or by logging on to Operator mode and going to reset camera Q Why is there a 2 second delay in the video and sound when viewing through SimView A The system aggregates the different audio and video sources and then relays them to any client logged on to SimView Server This makes it easy to view the all the feeds remotely with as little effort as possible for the end user but unfortunately the aggregation and relay add a delay Q How much space does my video recording take up on the hard disk A Have a look in chapter 5 2 4 on page 12 There is information here that provides sample file sizes based on the resolution level and length of the recording Q How do reset the AXIS camera to its factory defaults A To reset the camera to the original factory default settings use the control button and the restart button on the side of the camera as descri
24. annotations for the students but not to keep all the simulation on the server The simulations that need to be saved for later and frequent use must be exported with the export function to a remote storage server or a portable hard disk From the remote storage server all the simulations can be viewed with the SimViewer application from any PC connected to the storage server or using the portable hard disk You can export simulations in a format ready for the SimViewer application for viewing anywhere including offline as the files can be saved on USB memory sticks or portable hard disks You can also delete files not needed after being backed up somewhere else 7 2 What to back up Create a system image backup regularly as this will store all settings and programs for easy repair if the hard disk stops working In order to repair or move the SimView simulations it is important to make regular backups of the following folders e AvsFiles and any extra working directories used for storing video e App_Data folder in the SimView installation folder including the file avs sdf The AvsFiles folder is either specified in the Server setting in View amp Setup or placed at the default location C AvsFiles The App_ Data folder with the file avs sdf is located in lt System Drive gt Program Files x86 Laerdal SimView Server App Data See also the sub chapters Server settings General and Server settings Storage in
25. ave to be changed in order to use SimView instead of AVS Video Server If you should want to use AVS again just change the video setting back to the old values and remove legacy support in SimView Extension see Figure 3 The IP address for the SimView Server may have to include SimView if that is the address you must write in a browsers navigation field to connect to the SimView Server i e 192 168 1 125 SimView and not just 192 168 1 125 You can also use the name you have entered as the Computer name in the Control panel instead of the IP address see chapter 4 1 Use the Test connection button to make sure you have the correct server address then press Save and close Note SimView Extension must be installed after all other Laerdal software like the simulators SimMan3G SimMan etc and the Laerdal Debrief Viewer Status u Status ji Product Not Installed s Product Not Installed No Legacy Support imMan Legacy supported No Legacy Support i Legacy supported Product Not Installed SimJunior Product Not Installed No Legacy Support SimMo Legacy supported Product Not Installed Si y Product Not Installed Service installed it n Service installed Figure 3 The SimView Extension setup windows 4 6 Simulator setups for use with SimView The setup for the different types of simulators is shown in the next two chapters 4 6 1 Setting up SimMan3G and SimMan Essential SimMan3G and SimMan Esse
26. b before saving In the debrief window you can see the simulation if you are administrator you can also annotate the simulation A student user you can just watch the recorded session If you do any additions or changes to the simulation after the first save you must save again Tip If you forget to save a session or experience a problem causing the simulation to not be saved you can retrieve this session from the Server Settings section under View recovered simulations in the View and Setup screen 27 6 8 1 Printing the event log If you would like to have the Event log on paper you can use the Print option use the arrow to get the save as and the print option Print Save as gt MIELE i so Click here to get extra options If you not are administrator on SimView the Save button is exchanged with a Print button as you are not allowed to edit and save simulations gt MIN The print button for non admin users Figure 54 The print option give the possibility to make a PDF file of the Event log Do you want to open or save saps 10Emergency1BreathinglsaacMorris_Enter your initials_dkir9a66 pdf 137 KB from simviewserver1 Open Save v Cancel Figure 55 The options when doing a Print Save As x SSA p gt gt Downloads Search Downloads a P Organize v New folder jz w A E Fawon E Name Date modified Type BB Desktop J Downloads
27. bed on the next pages AXIS P5534 Using the control and restart buttons will reset all the parameters including the IP address to the factory default settings Remove the top cover 2 Press and hold the control button and the restart button at the same time 3 Release the restart button but continue to hold down the control button 4 Continue to hold down the control button until the status indicator color changes to amber this may take up to I5 seconds 5 Release the control button 6 When the status indicator changes to green which may take up to minute the process is complete and the camera has been reset The unit now has the default IP address 192 168 0 90 7 Put the top cover back in its original position It is also possible to reset parameters to the original factory default settings via the web interface For more information please see the online help or the User s Manual available from the AXIS Network Video Product CD supplied with this product 36 Camera Unit Control button SDHC card slot Status indicator LED Restart button AXIS M3204 This will reset all parameters including the IP address to the Factory Default settings Disconnect power from the camera 2 Press and hold the Control button and reconnect power 3 Keep the Control button pressed until the Power indicator flashes amber this may take up to I5 seconds 4 Release the Control button When the Power indicator d
28. cted to net tcp 127 0 0 1 15021 SapsServ Current profile my_used_profile SimStore status Not synchronized Options Figure 5 25 6 7 Operating the IP cameras The PTZ Pan Tilt and Zoom cameras can be operated from the View amp Setup page during watching and recording Moving the cursor into the picture frame will add the control buttons as well as the top banner with presets and Operator Mode Note The PTZ control in SimView only supports IP cameras and does not support analog cameras Note The built in controls in SimView are mainly to be used for adjusting the position of the cameras not for real time control during a session You can set new fixed position by clicking the star button once you have positioned the camera where you want it you will be asked to enter a name for the position You can have up to 5 different positions they will be shown at the top banner in the video window when you have the cursor placed inside the window The Operator button is for opening the AXIS control in a new browser window Note You will only have the control buttons if you are logged in as the administrator AXIS P5534 34 Operator Mode ra na CoffeCam Zomed in Resusci Anne Sao A ajri E4 Figure 52 Camera control buttons for PTZ cameras 6 7 1 Operator Mode The Operator Mode is used for real time control of the PTZ Use this option if you need to control video in real time during a session 26 6 8 Deb
29. dio Equipment If you are using external mixers for multiple microphones etc the installation is very similar to the simple one microphone setup The external audio equipment is connected either to the microphone input or the line input and then you must use the control panel to select to input you plugged the equipment into When using external audio equipment only one channel may be in use you will have to select the right one when setting up the audio In the audio setup you can clone from right or left channel to suit your setup the cloned channel will be copied to both channels for recording and playback 4 4 USB Web cam install Laerdal recommends using new models and particularly Microsoft web cameras Plug it into a free USB port 2 Install the supplied software and configure it according to the supplied user guide This may not be needed for all type of USB cameras 3 If the web cam includes a microphone you will have the possibility to use it instead of any other installed microphone 4 5 SimView extension installation and configuration If you are using SimView with Instructor Applications like SimMan SimMan3G etc you must install the SimView Extension Configuration tool on the PC running the Instructor Application and configure it according to your needs and the guideline described in this guide This is also the process you need to perform if you have updated from AVS The video settings in the Instructor Applications h
30. e the possibilities shown to the left otherwise the window at the right is for the normal user 22 6 4 Video windows J View amp SETUP f HOME BA Sinn iow aS Sim N admin Logout P Laerdar Heothsireom eee HE 00 00 E i V Equipment configuration Figure 42 The View window with one active camera D View amp SETUP HOME IMView aS Sim View e HRN 00 00 e 8 3 V Equipment configuration Figure 43 Picture in picture EJ view amp SETUP HOME admin Logout D Laerdal E Heornsireom HM 00 00 V Equipment configuration Figure 44 Three window layout CQ view amp SETUP f HOME admin Logout 2 kaeraat Heothsreom SimView Ay C a yj e et 00 00 Figure 45 Three active cameras and a patient monitor window setup When you have more than one camera active you can change the layout of the video windows and choose which camera to be show in the main video window by using the buttons in bottom control strip of the video window e s INM 00 00 Fa Figure 46 The window layout control 23 d Log off P Laerdar Hoornse Figure 47 Alternative four window setup The window top bar gives control over PTZ position 4 3 or 16 9 format control and expansion of video window The bar shows up when the mouse cursor is placed inside the window Format control Expand window eli EF Micro
31. esessceeesceeeessceeeseeeeeees 33 Ve OV SES UVIIN E UCU OM cesta E rnc seas Soma E E teased oases E tas aes eases eee Sate ee tas 34 SB WrOuDIESNOOUN G22 22022 ne N E E ROE E E E E OEE 35 1 Introduction The directions for use include comprehensive step by step instructions and illustrations for using SimView All supplied user manuals and labeling from original manufactures should be followed The SimView direction for use does not supersede those from the original manufacturer Check www laerdal com for newest version of this DFU 1 1 Before you start installing Have all actions from the Presales Questionnaire and site survey been solved successfully Is the Network infrastructure ready with the camera s connected Unpack the boxes and check that everything is delivered and undamaged so that you have all the needed parts ready before start Read the documentation before you start Install Figure 1 2 Quick installation overview The following is a quick overview of the steps needed to setup the SimView system They are only relevant if you are not having a Laerdal Representative to assist you with the installation at ge A If you ordered the cameras together with the SimView the first thing to do is to install the cameras in the planned places and connect them to the Ethernet if you already have the cameras in place then go to step 2 Install the PC and connect it to the Ethernet Connect keyboard and mouse
32. ipment Medium 20 Low 320x180 7 EAE AXIS P5534 Type IP address Login Password reed 14 Name Resolution cree p 4B ame ref 13 mecano Figure 19 Frames per second selection 5 2 7 USB Cameras Adding USB cameras is similar to adding IP cameras P A Gp a Liveview amp SETUP HOME al Sim leW A Making Simulation Easier admin Log off 2 taerdat Heorhsream VY Equipment configuration 2 patt eniaman Devices Select device to add v Add equipment Figure 20 Add equipment starting point V Equipment configuration Add equipment Devices Select device to add IP Camera Usb Camera Microphone Patient Monitor Analog Camera Figure 21 5 Equipment configuration Add equipment D h m p Select device to add IP Camera Ji Usb Camera Microphone R Patient Monitor Analog Camera Add equipment Figure 22 Equipment configuration Add equipment Devices Found devices Usb Camera v Logitech HD Webcam C510 X 7 gt Add equipment Figure 23 Equipment configuration E Logitech HD Webcam C510 Add equipment v Acti z a High 1280x720 30 fps Name Medium 640x480 30 fps Type Model name Logitech HD Webcam C510 Low 320x240 30 fps Figure 24 5 2 8 Audio To add a microphone to the simulation setup start SimView and login as Administrator To add the Windows default microphone or audio input that has been set up under the rec
33. isplays green which can take up to minute the process is complete and the camera has been reset It is also possible to reset parameters to the original factory default settings via the web interface For more information please see the online help or the user s manual AXIS M3204 Control button Power indicator LED Q can see a lot of simulations on the Home screen but cannot view them A The simulation file may have been moved or deleted without the use of SimView If the files are moved back they should play again if they have been deleted delete the entries on the Home screen they have been lost Q sometimes get a connection timed out or garbled video for my PTZ cameras A This can happen if the room has too little light Please make sure that there is light enough or change the PTZ camera settings according to the Axis manual To restore the connection press F5 Q The image is very choppy and or out of synch and or latency is very high A This happens if the network cannot handle the traffic properly i e low bandwidth or unstable connection e Make sure you are using a wired 100 Mbit network or faster e Cables are in good working order e Network is not congested 37 e Alternatively you can lower the resolution of the cameras to lower bandwidth usage If the video is played back on a low performance PC it may be the reason for the problems Q often have Time out
34. member last setting SJ Wording of log post amp comment markers Relative Positive Negative Neutral amp Period of inactivity before manikin goes into sleep mode minutes 20 Figure 5 The Profile editor setup for the SimMan3G e Enable Use video server AVS e Insert the IP address localhost or 127 0 0 1 is not allowed for the PC running the Instructor Application e Enable monitor recording e Set the quality to High screen size on patient monitor not to exceed Full HD 1920x1080 pixels Use the Save as to save the profile and the press Close e You must the start a new session in order to use the new profile Tip When SimMan3G starts you can make sure that the profile you saved is the one that is used for the session SimMan 3G Version 2 3 ver_ a Start Auto Mode Start Instructor Mode Open previously Patient Case Scenario saved session The profile used for the session Currently connected to net gp 127 0 0 1 15021 SapsServ Current profile my_used_ profile SimStore status Not synchronized Figure 6 The SimMan3G start screen showing the profile used 4 6 2 Non SimMan3G setup The setup for SimMan SimMom SimJunior Advanced SimNewB Advanced for SimPad ALS Advanced for SimPad SimJunior for SimPad and SimBaby is different as seen on the next illustration Video Recording Configuration z File View Simulation Recording camera Edit Monitor Setup
35. n If the built in user access functionality does not suffice then further restrictions can be imposed on the PC by adding Domain policies controlled by the local IT administrators on the network however this is the responsibility of the customer to set up as desired Note Some regions have laws or regulations stating that rooms under video audio surveillance must be properly marked with a sign or similar Please make sure you are complying with your local regulations 3 5 Unauthorized access to SimView content The SimView server software is as mentioned in the Privacy section above designed to prevent access to the content if a user does not have a login however it cannot be guaranteed that unauthorized access to content is not possible SimView Server should consequently never be exposed directly to the Internet Securing the PC with the proper Domain policies and restrictions is therefore needed and should be planned with customer s IT administrator if the PC is to be connected to the local network Proper polices for exporting and securely storing files should therefore be implemented and carried out if deemed necessary It is also possible to isolate the SimView server and connected peripherals such as cameras and Instructor Application PCs on a separate network in order to minimize risks If your site wishes to restrict access to SimView Server and access to make simulations there are some key points to adhere to e Users accessing the
36. n list of possible type of equipment V Equipment configuration Add equipment Select what type of device you want to add De Select device to add Analog Camera Add equipment Figure 14 IP Camera selected V Equipment configuration Add equipment Devices Found devices v Searching network v IP address Login Password Figure 5 IP camera search on going please wait V Equipment configuration Add equipment Devices Found devices i IP Camera v Axis M3204 192 168 1 v h again IP address Login Password a 192 168 119 80 Add equipment Figure 16 IP camera search finished and drop down list ready VY Equipment configuration Add equipment mao 9 Devices Found devices AXIS M3204 192 168 119 80 AXIS P5534 192 168 119 42 AXIS M3204 192 168 119 23 AXIS M1031 W 192 168 119 18 AXIS M1031 W 192 168 119 110 AXIS P5534 192 168 119 84 N Figure 7 IP camera selection with camera IP addresses shown 14 V Equipment configuration gt AXIS P5534 Set resolution for this device Aui aaoi High 1280x720 High 800x450 Medium 480x270 Low 320x180 V Active Name Type IP address Login Password ead IP Camera 192 168 119 84 ff o o o o o Model name AXIS P5534 5 15 Cenov Sve chnoe Figure 18 Video resolution selection V Equipment configuration EK AXIS P5534 Number of pictures shown each second Add equ
37. ndows control panel for System and Security under System Change the Computer name to suit your needs M E System an System Control Panel Home a 2 View basic information about your computer Device Manager Windows edition amp Remote settings Windows Server 2012 Advanced system settings Standard EE Windows Server 201 2 2012 Microsoft Corporation All rights reserved System Processor Intel R Xeon R CPU W3550 3 07GHz 3 06 z Installed memory RAM 8 00 GB System type 64 bit Operating System x64 based processor Pen and Touch No Pen or Touch Input is available for this Display W Change settings Computer description Workgroup WORKGROUP Windows activation Windows is activated View details in Windows Activation Action Center Windows Update Product ae Figure 2 The System Control panel showing the Computer name 4 2 Microphone installation Plug the microphone jack into the audio input port Open Control Panel from the Start button Select Sound Select the Recording Tab Select the microphone you want to use and select Properties Under the Listen Tab you can adjust the recording level set the level at press OK Now test if the level is adequate by looking at the bar level in the window while speaking ae So SS You will be able to add other audio sources via the SimView setup page as well not only the Windows default if you want to change set up 4 3 External Au
38. ntial use the same setup The next two pictures show how to setup the service File Simulation control View Tools SimStore Help PRR I OIA Student s monitor setup Common learner events Patient Monitor App Voice Conf App poor Auto start Voice Conf App a Profile Editor Scenario Editor Trend editor AA ntenanre ViaINtenance Messages gt Manikin setup Figure 4 SimMan3G Extension Service select the Profile Editor rofile Configuration CAUsers dkbhj1 DocumelfittsimMan3G profiles my_used _profile ricfg E a Ta aa ile Help Intro General Sounds Bleeding and fluids Patient monitor Drugs available Guidelines E General B Video Recording Reset this page to default B Recording source Use no recording O Use web camera one Use video server AVS amp Video server IP addre amen V Camera 1 C Camera 3 C Camera 4 Patient monitor recording Enable monitor recording B Monitor source identification for Video client SJ Monitor name monClientName I amp Port 5001 amp Maximum recording time minutes 120 a Units O Use SI units amp Capnometer unit mmHg J ICP unit mmHg amp Temperature F S Lactate unit mM i S Weight unit kg V Auto initiate auscultation focus C Sort learner event list alphabetically classic mode only J awRR source Any available CO2 primary ECG secondary J Compressor setup Re
39. o included in the event log file You can view the video either as a student or as an administrator Note Only the administrator can make annotations in the event log file to aid the student 6 1 The login screen When SimView Server is started the first thing to do is log in this is done on the login screen ay mV IEW So Login SA Laerdal HeothStream Q Advanced search Select view i Login to SimView User name l Password _ Remember me 2013 SimVentures All rights reserved Version V2 0 44600 0 About Figure 39 Enter your username and password and click Log in You will then see the home screen from where you can choose your next step If you do not have a login you should contact your SimView administrator 6 2 The Home screen 09 14 2012 04 19 4 Ee m tr igm s Asystole Nicholas Golden SimMan 3G SimBaby SimBaby Instructor Feclicia Pearson Instructor Feclicia Pearson Instructor Feclicia Pearson Head nurse Lance Reddick Physician Seth Gilliam i SimMan 3G SimMan 3G SimMan 3G Instructor Feclicia Pearson Instructor Feclicia Pearson Instructor Feclicia Pearson Head nurse Lance Reddick Physician Seth Gilliam Figure 40 The Home screen Select the simulation to watch by clicking on the link below the picture 21 If you are the administrator you can edit the simulation by adding comments These can help make the
40. ording tab in the Windows Sound Control Pane From the Home screen click the VIEW amp SETUP 1 Click the Add equipment link 2 Select the Microphone by selecting it from the drop down menu 3 and 4 Select the microphone you want to use from the drop down list 5 and 6 Click the Add equipment 7 button to update and exit Choose the stereo mode to suit your setup if you are using the line or microphone input 8 Bs Im E ias admin Log off D Laerdal HeothStrean DnukhWnN Equipment configuration 2 Add eguipment Devices Select device to add v Add equipment Equipment configuration Devices Select device to add IP Camera Usb Camera Microphone Patient Monitor Analog Camera Equipment configuration Usb Camera Microphone Patient Monitor Analog Camera Equipment configuration Devices Figure 25 lt 4 Figure 26 Figure 27 Microphone Found devices vi Microphone HD Webcam C510 hs 6 Equipment configuration Microphone HD Webcam C510 vV Active Name Figure 28 5 2 9 Patient Monitor To add the Instructor Applications Patient Monitor start SimView and login as Administrator mM hwWN a ds Input mode name 7 Microphone HD Webcam C5 f litchicdum is Clone from right Stereo Figure 29 From the Home screen click the VIEW amp SETUP 1 Click the Add equipment 2 button Click the in the
41. oup VBR Variable Bit Rate CBR Constant Bit Rate GOV Group Of Video 38
42. riefing When you stop the simulation in the Instructor Application you must go to debrief to save the recorded session When the debrief is opened you must log in to the SimView server in the browser window that opens on your Instructor PC You will only have to this once for each day or as long as you are logged in to the Instructor PC The window you will see after the login is the debrief window admin Logout Simulation Information Event Log Detailed View Q 00 00 Scenario started Healthy patient 3G 00 00 RR bpm 12 00 00 Convulsions type Off 00 00 Monitor capture started 00 00 awRR bpm 12 00 00 Heart rate bpm 80 00 00 BP 126 84 t 00 00 SpO2 98 00 00 PAP 25 10 00 00 etCO2 mmHg 34 00 00 Tblood C 37 2222222222222 00 00 etO2 16 00 03 AVS video recording started 00 05 Attach 3 lead ECG 00 06 Attach ABP sensor 00 06 TOF 100 00 07 Attach PAP sensor 00 07 NBP cuff attached 00 12 TOF measured TOF 4 99 00 13 Heart rate bpm 78 00 14 awRR bpm 11 ate of nrohs nttachod gt CM B Save vV DE ERL 5 Figure 53 The debrief window Note Only users with admin rights can save sessions In order to be able to see the recorded session later it is important to save the simulation using the Save button You can add the name of the instructor and the students name s to the Simulation Information ta
43. rivacy and security These matters are of course very dear to Laerdal 3 2 Whose responsibility is it to secure the SimView Server The SimView server system is by default not configured with any firewall or antivirus software It is the customer s responsibility to install such software and to include the PC in the normal Domain policies on the network Furthermore it is also the customer s responsibility to keep the PC s updated with the latest security patches This is due to the fact that once the PC is installed at the customer site Laerdal has no control over the PC and therefore cannot be responsible for maintaining security 3 3 Anti virus and Firewalls The PC is not supplied with an anti virus program Windows firewall is not activated by default It is the customer s responsibility to protect the simulation system components from unauthorized access 3 4 Privacy Content stored on the SimView server cannot be accessed without proper login credentials Two types of login exist to get access to the stored simulations One type grants access to change the configuration delete files and edit logs and the other type only grants access to view the simulations and live video feed without being able to change anything You can create as many users as needed on the system It is important to understand that there is no filtering done on the logins which means that all content stored on the server can be viewed by everyone with a valid logi
44. soft LifeCam HD 5000 g ED ow Figure 48 Controls on the small video window Pre defined PTZ possitions Open AXIS camera window if su tad by the camera silts window AXIS P5534 Operator Mode E HH meeting Test lo Pos 2 Home Figure 49 Controls on the expanded window The swap window button will swap the window in the Main Video Window with the contents of the Small Video Window the Expand Window button will expand the window to fill the entire video frame to only showing this one video stream Note The functions on the control bar depend on the user type that is logged in only when logged in as the SimView administrator the PTZ controls and the Operator Mode are available Tip The web browser must have its pop up blocker disabled in order to use the Operator Mode for the AXIS cameras Note The layout is optimized for widescreen displays in 16 9 format things may look different and less optimized when seen on a 4 3 format screen 24 6 5 Recording a scenario The scenario recording is started and stopped from one of the Instructor Application like SimMan or SimMan3G etc The cameras connected to the server will provide video footage to cover the scenario together with the input from the Patient Monitor and the Instructor Application The maximum recording length in SimView is 4 hours but the Instructor Applications may have other restrictions on the maximum recording length the shortest will apply
45. stem error log r 2 gt Save changes Figure 66 The automatic clean up for saved simulation is enabled on the server settings by entering the number of days that simulation have to be older than in order to be deleted 1 and then click in the check to enable the feature box and save changes 2 you will get at warning to alert you about the automatic deletion of files See Figure 66 Note Sessions marked as favorites will not be deleted 7 4 System notification admin Logout System notifications 3 Laerdal Heokhstrean Figure 67 If you get this message you will have to click it and under server setting you will see what caused the warning Note Only the admin user is able to see the information in the Server settings Server settings General Disk Usage System notifications a name Available disk space Running low on disk space SimServer N 71 Please do a manual clean up D AVSFiles l Automatic clean up options SMTP server TA Delete data that is older than 90 days Ost E Run automatic clean up now View recovered simulations User administration SimView system error log Save changes Figure 68 Solve the issue indicated in the System notification area This can be system driver upgrade or as shown here a hard disk clean up 34 8 Troubleshooting Q My events and timeline don t match Timeline starts in wrong position A Make sure that all
46. student aware of errors or things done correctly Note The students or regular users cannot edit the simulations Tip The picture shown together with the simulations is a snapshot from the first camera added during initial configuration i e the leftmost enabled camera tab in the Equipment configuration Besides being able to view the simulation you also have 3 options if you click the triangle in the bottom right corner e Delete the simulation if it is not relevant anymore and for freeing up space on the hard drive e Add the simulation to favorites e Export the simulation e Share the simulation For more information on the last two topics see chapter 6 9 Sharing simulations 6 3 The View amp setup window The options available on the View amp Setup screen depend on the user s role administrator or user The View amp Setup window also gives administrator the possibility to change the configuration of SimView more information on setup in SimView The Administrators Direction for Use The View amp Setup window shows the images captured from the active camera you will see images from all active cameras if you have more than one active camera HHMI 00 00 MicrosoR UiteCany HD 5000 AXIS M3204 Patent Monostor aS P5534 Microphone Add equipment 2012 SimVentures All rights reserved r ion V2 3493 0 About Figure 41 The two type of View amp Setup screens If you are an admin user you will hav
47. th the software pre installed The first time you want to access SimView you can do so by following these steps A default administrator user is already created with the following login information User admin Password Laerdall Important You should change the password for this user once you are ready to use the system a On the desktop you will see the SimView application icon To start the SimView double click the SimView icon on the desktop 5 2 Configuration In order to use SimView it will have to be configured with the addition of extra users and different external component like microphones cameras Patient Monitors etc this is done in the View amp Setup window 5 2 1 Users In order to use SimView Server users have to be added Note If no SMTP server address is setup it will not be possible to reset a lost password for any account including the administrator account in SimView Se the chapter Server settings General for more info on how to setup the SMTP address To add more users you must login as administrator using the username and password you have chosen in the previous steps Click the VIEW amp SETUP button 1 2 Click the Server settings 2 triangle to open the dialog 3 Click the User administration 3 this will open an input window where all details about the user can be entered Fill out all the fields 4 Click the User type radio button 5 to give the user a role Click the
48. ulation 30 6 10 Simulation sessions 6 10 1 The timeline The timeline in the bottom of the Viewer Window can be used to search forward and backward in the session The timeline size can be controlled by clicking the double arrow that shows up in the right top corner of the frame when the cursor is inside the timeline Clicking inside the timeline will move the video forward or backward depending on clicking in front or behind the actual play time Holding the cursor over the vital signs will activate a pop up with the values of the vital signs at that time Expand timeline nable vitalsign Collapse timeline curves Actual play time 01 15 Figure 62 The different timeline views 6 10 2 Basic and Detailed Views The simulation log can be showed with two different levels of detail in the Event Log As seen on Figure 63 there are a lot more information in the detailed view so if you want to just get an overview of the session use the basic view Simulation Information Event Log Simulation Information Event Log Basic View 7 Q Detailed View Q 00 00 Scenario started Healthy patient 3G 00 00 Scenario started Healthy patient 3G 00 00 Monitor capture started 00 00 RR bpm 12 00 05 Attach 3 lead ECG 00 00 Convulsions type Off 00 06 Attach ABP sensor 00 00 Monitor capture started 00 07 Attach PAP sensor 00 00 awRR bpm 12 00 07 NBP cuff attached 00 00 Heart rate bpm 80 00 12 TOF measured TOF 4
49. ures of SimView The person who gets the link must have access to the SimView server via the local network but does not need a SimView account to see the simulation The access via this link will be restricted to only this one simulation e Export o You can save the full session containing all the data for stand a lone use with SimViewer or for backup purposes o You can also select to just export a video file with audio which can be played in a Media Player e Delete the simulation if it is not relevant anymore and for freeing up space on the hard drive Q Advanced search 11 50 2013 Jan 25 Healthy patient SimMan Share private link Delete Participants added No participants added ST Instructors No instructors added No instructors added Figure 58 Export or share a private link to a simulation Choose simulation data to export x Patient Monitor AXIS M3204 Export selected Figure 59 Export options The Simulation Activity File is an ssx file for use with the SimViewer application it includes the whole scenario with vital signs event log and video from all cameras and the patient monitor used during the session It looks as seen on the SimView Server The video file is a mov file for use with a media player application Microsoft Media Player or QuickTime it is the video file from the selected camera or patient monitor including audio if a microphone has been enabled there is no vital signs or event
Download Pdf Manuals
Related Search
SimView simviewer simview software simview1251 simview keysight simview microscope simview psim simview server