VSOF-CS201A
Contents
1. 2 Fixing from bolt middle of 2port sheath holder Figure 41 Figure 40 Figure 41 1 18 Arranging Protection Tube and Fiber 1 18 1 Arrange the protection tubes using the cable guide saddle under the tray Figure 42 1 18 2 Arrange the protection tubes considering the bending radius Insert the protection tubes into the inlet on the tray and fix by using cable ties Figure 43 44 1 18 3 Coil surplus fibers in the tray in a figure 8 shape figure 45 1 18 4 Record each splice on the index card on the lid figure 46 Figure 42 Figure 43 9 10 CS201A User Manual Rev 1 Figure 44 Figure 45 Figure 46 1 19 Assembling the Closure 1 19 1 Push front of Handle until there is a sound such as clack Figure 47 1 19 2 In case of drop cable moved the other side use Drop Cable guide at main body bottom Figure 49 50 Figure 47 Figure 48 Figure 49 Figure 50 10 102. 0mm from the cable sheath end remove the rest of the loose tube Figure 5 1 5 2 Clean the cut area by using jelly cleaner A Be sure not to damage the fiber optics Figure 5 1 6 Inserting Unit Protection Tube 1 6 1 Insert fibers into the unit protection tubes carefully all the way up to the point where loose tubes end Figure 6 1 6 2 Wrap the tape around the end point of protection tube at cable side Figure 7 A Be careful not to damage inner fibers Unit Protection Tube Figure 6 Figure 7 3 10 CS201A User Manual Rev 1 1 7 Fixing Cable sheath and Tension Member 1 7 1 Apply the grease in the middle of sheath gasket of the closure Figure 8 Figure 8 1 7 1 Put the T M supporter cover on the T M and tighten them together Figure 9 Figure 9 Figure 9 1 1 8 Fixing Sheath Holder amp Messnger Wire Cover 1 8 1 Apply the high vacuum grease on the upper sheath gasket Figure 10 1 8 2 Fix the cable sheath holder main gasket holder and messenger wire cover by using a screwdriver Figure 11 12 13 Figure 10 Figure 11 Figure 1 2 Figure 13 4 10 CS201A User Manual Rev 1 1 9 Arranging amp Fixing Protection Tube 1 9 1 Attach the protection tube using a cable tie and cut the cable tie Figure 14 15 16 1 9 2 Arrange a fiber optic unit considering the bending radius Figure 17 Figure 14 Figure 16 Figure 1 7 1 10 Connecting the pigtail 1 10
3. 1 Connect the pigtail on the module Figure 18 19 1 10 2 Arrange fiber optic units considering the bending radius Figure 20 1 10 3 Put units into the hole on the other side Figure 21 Figure 1 8 Figure 19 Figure 20 Figure 21 5 10 CS201A User Manual Rev 1 1 11 Arranging amp Fixing Pigtail Tray Part 1 11 1 Arrange the pigtail considering the bending radius Figure 22 1 11 2 Insert pigtail into the sprial protection tubes carefully all the way up to the point where pigtail end Figure 23 1 11 3 Attach the pigtail protection tube using a cable tie and cut the cable tie Figure 24 Figure 22 Figure 23 Figure 24 1 12 Splicing and Storing Fibers 1 12 1 Preparation 1 12 1 1 Clean the working desk and check the fibers carefully 1 12 1 2 Cut each fiber end carefully to make a perpendicular cut to the fiber axis 1 12 2 Splicing 1 12 2 1 Splice fibers in accordance with splicing method to approved A Be careful not to twist or bend fibers A There should be no damage or flaw on the cut area and keep the fibers from dust to minimize the data loss A If there is any problems with the splice then cut the splicing point and splice them again 1 12 3 Arranging the splices 1 12 3 1 After the splice insert the splice protection sleeve in each slit accordingly Figure 25 1 12 3 2 Coil surplus fibers in the tray in a figure 8 shape Figure 26 1 12 3 3 After the arrangement apply the O ri
4. VSOF CS201A ODP Aerial Closure for Fiber Optic Cable User Manual Rev 1 CS201A User Manual Rev 1 1 Direction 1 1 Getting Started 1 1 1 Confirm the cable structure and the fiber type before starting the work Different types of fibers cannot be spliced together 1 1 2 Seal the splicing part perfectly to minimize cable damages by moisture Do not apply any impact to the splicing part 1 1 3 Keep the working place free from moisture or dust Do not give any impact on the cables Do not bend or twist cables 1 1 4 During the sheath stripping and the closure assembly procedures use permitted tools according to an approved fiber optic splicing standard in your region 1 2 Marking a Cutting Point 1 2 1 Mark a sheath removing point on the cable with a piece of tape at a 700mm point from right and left the Closure Installation point Figure 1 1 2 2 Divide messager wire and cable from marking point by cutter Figure 2 Figure 1 Figure 2 1 3 Sheath Removing 1 3 1 Remove the cable sheath from the marked point using a sheath stripper Figure 3 A Be sure not to damage the fiber optics Figure 3 Figure 3 1 2 10 CS201A User Manual Rev 1 1 4 Cutting tension Member 1 4 1 Cut the T M at the 70mm point from the cable end Figure 4 A Be careful not to cut loose tubes 70mm INUIT NU YL Wifi 3 Offi it 2g WA Wii Figure 4 1 5 Removing Loose Tubes 1 5 1 Leave about 40 6
5. ng into the slit and close the tray lid 1 12 4 Record each splice on the index card on the lid Figure 27 6 10 CS201A User Manual Rev 1 THUN CUCccccccee Figure 25 Figure 26 Figure 27 1 13 Connecting Drop cable connector 1 13 1 Fix Drop Cable by Drop Cable holer Figure 28 29 1 13 2 Fix Drop Cable holder Figure 30 31 1 13 2 Insert Drop cable gasket Figure 32 1 13 3 After work completion Fix Drop cable at the main cable by cable tie Figure 36 Figure 28 Figure 29 Figure 30 Figure 31 7 10 CS201A User Manual Rev 1 Using the hole Figure 32 Figure 33 1 14 Preparing Distribution Cables 1 14 1 Do the step from 1 2 to 1 7 One different thing is a cutting point of a sheath is 120cm point from the cable cut end Figure 34 Figure 34 1 15 Inserting Distribution Cables 1 15 1 drill a hole in the 2 port gasket by the screw drive Figure 35 1 15 2 Apply the high vacuum grease inside drilled hole 1 15 2 Insert the distribution cable into the 2 port gasket Figure 36 37 Figure 35 Figure 36 Figure 37 8 10 CS201A User Manual Rev 1 1 16 Fixing Tension Member of Distribution Cables 1 16 1 Put the T M supporter cover on the T M and tighten them together by using screw driver Figure 38 39 Figure 38 Figure 39 1 17 Fixing 2 port Sheath Holder 1 17 1 In case of 8 9mm Cable apply sheath fixing gasket Figure 40 1 17
Download Pdf Manuals
Related Search
VSOF CS201A