Black Diamond LED Moving Wash SI
Contents
1. Should you need any spare parts please order genuine parts from your local dealer CE Black Diamond LED Moving Wash SI 031 OK OKO O O O O O Xe o o OROKO O O O O 10 to O to on 0 0 0 O O ORo Oo oO 0 0 0 0 O 0 9 O XXY 42 O19 0 010 AA 0 0 0 OO eROKS SASA O O of eaaa jo User Manual KEEP THIS MANUAL FOR FUTURE NEEDS 1 Unpacking Thank you for Color Imagination s Black Diamond LED Moving Wash For your own safety please read this manual before installing the device This manual covers the important information on installation and applications Please install and operate the fixture with following instructions Meanwhile please keep this manual well for future needs Color Imagination s Black Diamond LED Moving Wash is made of a new type of high temperature strength of engineering plastics and cast aluminum casing with nice outlook The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol It s available independently controlled and linkable with each other for operation And it is applicable for large scale live performances theater studio nightclubs and discos SI 031 adopts 138PCS powerful 3W LEDs2. Pulse random strobe from slow to fast Channel Ls Ls 7 cS 0 008 Strobe from a ceiling or set on a flat level surface see illustration below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting points Overhead mounting requires extensive experience including amongst others calculating working load limits a fine knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture If you lack these qualifications do not attempt the installation yourself Improper installation can result in bodily injury Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet Clamp Mounting The Moving Head wash provides a unique mounting bracket assembly that integrates the bottom of the base the included Hanging Kits and the safety cable rigging point in one unit see the illustration below When mounting this fixture to truss be sure to secure an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the center hole of the omega bracket As an added safety measure be sure to attached at least one properly rated safety cable to the fixture using on of the safety cable r
3. 12 Maintenance and Cleaning The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION Disconnect from mains before starting maintenance operation In order to make the lights in good condition and extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakneness of the lights due to accumulation of dust 2 Clean the fan each week 3 Adetailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions
4. ed personnel who knows the fixture before using Keep the original packages if any second shipment is needed Don t try to change the fixtures without any instruction by the manufacturer or the appointed repairing agencies lt is not in warranty range if there are any malfunctions from not following the user manual to operate or any illegal operation like shock short circuit electronic shock lamp broke etc 4 Mounting and Installation Cautions For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture RGB Effect 7 Photometric Data 25 Beam Angle R 1763 650 365 177 LUX G 2840 1080 630 305 LUX B 3980 1565 897 440 LUX W 3040 1220 715 355 LUX RGBW 11500 4730 2650 1230 LUX a buy weeg Sz 0 3 5 7 10 Distance m 0 2 5 3 6 4 8 6 5 Diameter m 8 DMX Channels Values Description 1 0 255 Linear PAN Movement 540 or 630 0 255 Linear Tilt Movement 280 0 255 0 100 Linear Dimmer from dark to bright Red 0 255 0 100 Red dimmer from dark to bright 134 255
5. he manufacturer or his service agent or a similar qualified person in order to avoid a hazard 7 Manual Press MENU to select the Manual option Then select the channels Then select the DMX values through UP DOWN And press ENTER to set it 8 Restore Press MENU to select the Restore option Then press UP DOWN to select Motor Factory And press ENTER to set it 3 Operation Instructions The moving head is for wash effect for onsite decoration purpose Don t turn on the fixture if it s been through severe temperature difference like after transportation because it might damage the light due to the environment changes So make sure to operate the fixture until it is in normal temperature This light should be keep away from strong shaking during any transportation or movement Don t pull up the light by only the head or it might cause damages to the mechanical parts Don t expose the fixture in overheat moisture or environment with too much dust when installing it And don t lay any power cables on the floor Or it might cause electronic shock to the people Make sure the installation place is in good safety condition before installing the fixture Make sure to put the safety chain and check whether the screws are screwed properly when installing the fixture Make sure the lens are in good condition It s recommended to replace the units if there are any damages or severe scratch Make sure the fixture is operated by qualifi
6. igging point integrated in the base assembly Regardless of the rigging option you choose for your wash LED always be sure to secure your fixture with 6 Over Views and Dimensions View of Back Panel a safety cable The fixture provides a built in rigging point for a safety cable on the hanging bracket as illustrated above Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle 5 DMX 512 control connections Connect the provided XLR cable to the female 3 pin or 5 pin XLR output of your controller and the other side to the male 3 pin or 5 pin XLR input of the moving head You can chain multiple Moving head together through serial linking The cable needed should be two core screened cable with XLR input and output connectors Please refer to the diagram below DMX 512 connection with DMX terminator View of Power Panel re te Pu oo fi C Ue Terminator Next Fixture DMX512 o DMX512 aiia Oo O n 3 4 Oo O 3 4 5 OUT IN For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as in a discotheque it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 Q resistor connected between pins 2 and 3 which is then pl
7. n through UP DOWN Then press UP DOWN to j Y Always disconnect from the mains when the device is not in use or before cleaning it Only handle the select the language you would like to set And press ENTER to set it ower cord by the plug Never pull out the plug by tugging the power cord 3 Pan Invert Press MENU to select the Pan Invert option through UP DOWN Then press UP DOWN to P ne P eon epee p During initial start up some smoke or smell may arise This is a normal process and does not select YES NO for invert pan or not And press ENTER to set it necessarily mean that the device is defective it should decrease gradually 4 Pan Angle Press MENU to select the Pan Angle option through UP DOWN Then press UP DOWN to i 7 i Please don t project the beam onto combustible substances select 540 or 630 And press ENTER to set it Fixtures cannot be installed on combustible substances keep more than 50cm distance with wall for 5 Tilt Invert Press MENU to select the Tilt Invert option through UP DOWN Then press UP DOWN to smooth air flow so there should be no shelter for fans and ventilation for heat radiation select YES NO for invert or not And press ENTER to set it If the external flexible cable or cord of this luminaries is damaged it shall be exclusively replaced b 6 Mode Press MENU to select DMX512 Auto SOUD or Slav through UP DOWN Then press UP DOWN g oe 2 osdectrone dite above nd press ENTER to setik t
8. ugged into the output XLR socket of the last m Imi fixture in the chain Please see illustrations below 1209 ON a rT NN Ua Dd 7 PIN 3 PIN 2
9. when touching wires Language Chinese English This device has left the factory in perfect condition In order to maintain this condition and to ensure a pPaninvert fves No ff safe operation it is absolutely necessary for the user to follow the safety instructions and warning jTitinvert Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems w o o o auto ff If the device has been exposed to temperature changes due to environmental changes do not switch souo ff it on immediately The arising condensation could damage the device Leave the device switched off stay ff until it has reached room temperature Manual CHxx Datax ff This device falls under protection class Therefore it is essential that the device be earthed Motor ff The electric connection must carry out by qualified person ee The device shall only be used with rate voltage and frequency 1 Make sure that the available voltage is not higher than stated at the end of this manual DMX addresses Press MENU to select the DMX Addre option through UP DOWN Then press Make sure the power cord is never crimped or damaged by sharp edges If this would be the case UP DOWN to select the DMX address you would like to set And press ENTER to set it replacement of the cable must be done by an authorized dealer 2 Language Press MENU to select the Language optio
10. which features high brightness and stability Please carefully dispack it when you receive the fixture and check whether it is damaged during the transportation And please check whether the following items are included inside the box Moving Head one Signal Cable one Hanging Kits Two User Manual one Safety Chain One 10 Key Features 138PCS 3W high power LEDs RGBW 50 000 hours lifespan and low power consumption 8 16 bit smooth and precise resolution for PAN TILT movement 540 pan and 280 tilt movement Scan position memory auto reposition after unexpected movement RGB color mixing system LED shutter LED dimming LED rainbow effect Macros effect Strobe effect with 18 flashes per second and pulse effect General dimming and blackout for all four colors 16 DMX channels DMX512 master slave and sound activated controllable or auto operation Blue background LCD display 11 Technical Specifications Input Voltage AC90 240V 50 60Hz LED Quantities 36 red 36 green 36 blue 30 white 3W Control Signal DMX512 master slave and sound activated or auto operation Control Channel 16 DMX Channels Power Consumption 400W Dimensions 446x517x432mm Packing Dimensions 460mm 335mm 385mm Net Weight 15kgs Gross Weight 17kgs 9 Menu Operations 2 Safety Instructions a S o o o l CAUTION Be careful with your operations With a dangerous voltage you can Suffer a dangerous electric shock
Download Pdf Manuals
Related Search