HomeSeer HSM200 Guide
Contents
1. 00 includes a system controllable multi colored LED that may be programmed with events to change color when things THEN Control a Device T happen in the home HomeSeer HS3 system Node 2 Z Wave Color Control users can do this by following these steps a Goto View gt Events and create a new IF This event is MANUALLY triggered event After Waiting 0 Days O Hours O Minutes O Seconds i Red b After selection your trigger select the Green Blue Control a Device action Wacan c Select HSM200 Z Wave Color Control a option v Options gt Cyan d You can now select which color you White would like the LED to change based on your trigger Updating the Device Firmware From time to time HomeSeer will update the firmware Here the HSM200 firmware can be updated without having to send the device back and forth with HomeSeer support Go to your Device Management page or click Home and click on the Root device for your HSM200 Click on the Z Wave tab at the top to go to the Z Wave Device control page In the Firmware Update section click Select File and select the HSM200 Firmware upgrade file Let the upgrade procedure finish before leaving the page S Setting Up Device Associations Go to your Device Management page or click Home and click on the Root node for your HSM200 Click on the Z Wave tab at the top to go to the Z Wave Device control page Expand the Associations section The device should automatic2. HomeSeer HSM200 Guide This guide contains instructions for setting up your HomeSeer HSM200 multisensor The HSM200 is designed to sense motion temperature and light levels and will work with most Z Wave certified controllers or smart hubs HomeSeer HS3 system users can also program the unit to display up to 7 different colors when things happen in the home Since the HSM200 is line powered it can function as a Z Wave network repeater and there are no batteries to replace D Adding the HSM200 to your Z Wave Network for HomeSeer HS3 System Users The HSM200 can be added directly through HS3 or can be added via your Z Wave controller and then imported see below if you are not using HS3 a Navigate to Plug ins gt Z Wave gt Controller Management Expand your Z Wave controller b Open the Actions menu and select Add Include Z wave Device c Click Start to initiate the Add process and press the button once on the side of the HSM200 to put it into Inclusion mode The process will take some time to complete n ch Unknown je No Stabs Node 2 7 Wave HomeSeer Tech Unknown 7 Node 2 Root Motion Location Node 2 Z Wave Home Security Today 11 00 14 AM Off Red Green Blue Blue Node 2 Z Wave Color Control Today 11 13 25 AM Magenta Yellow Cyan White Node 2 Z Wave Temperature Today 10 40 48 AM Node 2 Z Wave Luminance Today 10 40 48 AM Adding the HSM200 to your Z Wave Network for non HomeSeer systems The HSM200 is Z Wave
3. ally associated with HomeSeer but it can be associated with other devices as well sega Page 2
4. certified multi sensor that should work with any Z Wave certified system controller Please follow the procedure required by your controller manufacturer for adding pairing the HSM200 with your Z Wave network Note The Color Control will only work if your control system support the Z Wave Color Command Class Please check with the manufacturer of your system to verify compatibility Removing the HSM200 from your Z Wave Network for HomeSeer HS3 System Users Should you need to remove or reset your HSM200 to its factory configuration please follow this procedure a Navigate to Plug ins gt Z Wave gt Controller Management Expand your Z Wave controller b Open the Actions menu and select Remove Exclude Z wave Device c Click Start to initiate the Remove process and press the button once on the side of the HSM200 to put it into Exclusion mode The process should take very little time to complete Page 1 Configuring Device Settings The HSM200 has some Device Settings that can be configured a Goto your Device Management page or click Home and click on the Root device for your HSM200 b Click on the Z Wave tab at the top to go to the Z Wave Device control page c Onthis page the HSM200 can be rescanned optimized removed and other functions Expand the Settings section d Inthe settings section the Name and Location of the Node can be configured internally on the HSM200 Creating Events to Utilize Color Control The HSM2
Download Pdf Manuals
Related Search