Untitled
Contents
1. HINA APS300 PURE SINE WAVE POWER INVERTER2. YOUR LEADER IN POWER SOLUTIONS APS300 PURE SINE WAVE POWER INVERTER USER S MANUAL Read these instructions before connecting and using your PowerBright Pure Sine Power Inverters Failure in observing this warning may result in injury to persons and damage to equipment General safety and installation information Warning The following fundamental safety measures must be observed when using electrical equipment to avoid danger of Electric shock Fire Injury About the unit itself The inverter must only be used for the purpose specified by the manufacturer Do not operate the inverter if the housing of cables are damaged The inverter must be positioned and secured safely in order to avoid knocking over or dropping If casing needs to be opened make sure Input cables have been properly disconnected The inverter must be kept in a safe place out of the reach of children The inverter may not be operated in a damp or wet environment The inverter may not be used in rooms containing flammable materials Make sure the inverter is well ventilated Service and repair may only be carried out by skilled persons who are familiar with the risks involved and the relevant regulations Caution by installation on boats Incorrect installation of electrical units on a boat may lead to corrosion of the boat Therefore please let a boat electrician carry out the installation of the inverter I
3. e not being exposed to humidity Make sure there is proper ventilation Keep at least a free space of 10 cm surrounding the inverter If installed into housing make sure there s good ventilation The air intake on the bottom of the inverter and the air outlet on the back side may not be blocked In case of ambient temperatures of more than 35C e g engine or heating room direct sunlight the inverter will switch off automatically because of self heating effects during operation The installation surface must be balanced and sufficiently strong Installation of the inverter Adjust the inverter to the chosen installation place and mark the fixing points Fix the inverter by using the self chosen fixing method Electrical connection General instructions for electrical connection In case of the inverter is installed into vehicles or boats it has to be connected to the chassis ground If cables have to be inserted to metal walls or other sharp edged means use a cable duct or cable bushes Do not pull the cables Do not lay cables loose or in sharp bends on electrical conducting materials metal Do not lay 110V mains cable and 12 24 VDC cable together into the same cable duct The specified minimum cable cross section must be complied with Secure cables properly Lay cables in such a way that no tripping is possible Lay cables in such a way that no exposure to or risk of damage is possible Cables Make sure t
4. ice Wait approx 2 minutes and switch on the inverter only Reduce the load and make sure that there is better ventilation for the inverter Then switch on the inverter and the device again Overload LED Current consumption of the device is too high Also there could be a short of the device Switch off the inverter and disconnect the device Switch on the inverter again If the OVERLOAD LED is off there is a short circuit in the device or the total load was higher than the specified wattage of the inverter Check the connecting cable of the consumer for mechanical damages Audible signal in case of under Battery voltage too low In case of the voltage battery load voltage falls below 11V resp 22V The battery has to be re charged Specifications APS300 Model APS300 12 APS300 24 Continuous Power 300W 300W 20 Minutes 350W 350W Surge 500W 500W Output Voltage 110V 3 110V 3 Output Frequency 60Hz 60Hz Output Waveform Pure Sine Wave Pure Sine Wave Total Harmonic lt 4 lt 4 Distortion Input Voltage 10V 15V 20V 30V Range Efficiency gt 90 gt 90 No Load Current 0 7A 0 35A Draw Low Battery Alarm 10 7V 21 4V Low Battery Shut 10V 20V Down Dimension 11 x 4 2 x 2 4 in 11 x 4 2 x 2 4 in Lx W x H Weight 5 Ibs 5 Ibs ET EEG Z d YOUR LEADER IN POWER SOLUTIONS www PowerBright com TOLL FREE 1 866 295 6775 DESIGNED IN USA ASSEMBLED IN C
5. ntended use The inverter is suitable for e g high quality appliances from the audio video or PC The output voltage corresponds to the standard one of your socket pure sinus voltage Attention Please note that appliances like drills TV s or refrigerators require a high starting current which is far over the nominal current With its low weight and the compact design the inverter can be easily installed into campers commercial vehicles or motor and sailing yachts Note Some devices contain AC motors or compressors IE drills refrigerators etc which require a higher wattage during startup This wattage typically exceeds the rating listed on the device Delivery Kit No Pieces Description Ref No 1 1 Pure sine wave inverter with APS300 12 connection cable APS300 24 2 1 Instruction Manual Required tools and installations equipment Depending on type of installation the following tools are required set of screw drivers drill and set of bits wrench crimping shears for the12 24V wire connection For connection of inverter to the battery the following cable connecting hardware is needed 2 different flexible cable connections Various terminals multi core cable ends Caution Before drilling any mounting holes make sure that there are no wires fuel lines or tanks directly below the surface being drilled Installation The inverter has to be installed in a dry and clean plac
6. o DC Amps Req d Wire Gauge use the correct cables A chart is provided below for your reference Max Watt Output 6oow 60A 6or2x 10 Connection to the battery Lay the flexible connecting cable positive and negative from the battery to the connecting terminals of the inverter take cable cross section from the table Connect first the positive then the negative cable Make sure the terminals are not reversed Reverse polarity connection will blow the internal fuses This will void the warranty Lay the flexible chassis ground cable from the chassis of the vehicle to the chassis ground on the rack of the inverter Connect the chassis ground Reverse polarity connection of the battery wires can damage the inverter Do not use the inverter with electrical systems using positive ground Operation 300 Watt Pure Sine Wave Inverter Power on On the LED control Power lighting Green LED Over load One the LED control Over Load lighting Red LED Over temperature On the LED control Over Temp lighting Red LED Possible Cause No output voltage 1 On Off switch is not in the power ON LED does not light position 2 Bad contact of the connections between battery and inverter 3 Internal fuses blown In this case send the unit back to Power Bright for repair No output voltage OVER TEMP The inverter has been overheated LED Lights Red Switch off the inverter and the dev
Download Pdf Manuals
Related Search
Untitled untitled boxing game codes untitled document untitled goose game untitled spreadsheet untitled notepad untitled paint untitled app untitled presentation untitled entertainment untitled attack on titan codes untitled 1 untitled boxing codes untitled tag game codes untitled stream untitled ui untitled 2 untitled boxing game wiki untitled paint 3d untitled diagram untitled music app untitled boxing game tier list untitled form untitled design untitled music untitled mod menu