XRLED 700 Spot
Contents
1. XRLED 700 Spot PR 8163 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD http www pr lighting com 2 21 SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 POWER SUPPLY MAINS 5 CONTROL CONNECTIONS 5 DMX TERMINATOR 6 SETUP OPTIONS PROJECTOR CONFIGURATION 6 TO SET THE DMX START ADDRESS 7 STAND ALONE MODE 7 MASTER SLAVE MODE 7 OPERATION MENU 8 REPLACING GOBOS DMX PROTOCOL 12 INDICATION OF LED DIGITAL TUBE 13 MAINTENANCE 14 LUBRICATION 14 KEEPING THE PROJECTOR CLEAN 14 TROUBLESHOOTING 14 TECHNICAL DATA 15 ELECTRICAL DIAGRAM 17 COMPONENT ORDER CODES 19 Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused b2. 1 Iris 224 239 Iris effect 2 240 255 Iris effect 3 Iris Fine 0 255 Iris in 16 Bit precision 000 015 White 016 031 Gobol 032 047 Gobo 2 048 063 Gobo 3 064 079 Gobo 4 080 095 Gobo 5 096 111 Gobo 6 Fixed Gobo 112 127 Gobo 7 Wheel 128 143 Rotation from slow to fast 144 159 Reverse rotation from slow to fast 160 175 Gobo shake 1 from fast to slow 176 191 Gobo shake 2 from fast to slow 192 207 Gobo shake 3 from fast to slow 208 223 Gobo shake 4 from fast to slow 224 239 Gobo shake 5 from fast to slow 240 255 Gobo shake 6 from fast to slow 000 015 No Gobo 016 031 Gobol 032 047 Gobo 2 Rotating Gobo 048 063 Gobo 3 064 079 Gobo4 080 095 Gobo 5 096 111 Gobo 6 112 127 Gobo 7 13 21 128 143 Rotation speed from slow to fast 144 159 Reverse rotation from slow to fast 160 175 Gobo shake 1 from fast to slow 176 191 Gobo shake 2 from fast to slow 192 207 Gobo shake 3 from fast to slow 208 223 Gobo shake 4 from fast to slow 224 239 Gobo shake 5 from fast to slow 240 255 Gobo shake 6 from fast to slow 000 207 0 540 indexable 208 223 Gobo rotation from slow to fast 7 7 9 Gobo rotation 224 239 Stop rotating 240 255 Reverse rotation from slow to fast 8 10 re 000 255 Gobo rotation in 16 Bit precision 000 019 No 8 9 11 Frost Filter 020 255 Frost Effect 000 019 White 9 10 12 Prism 020 255 Prism 000 063 Stop rotating 064 127 Prism rota
3. 4 fast fit screws Before the replacement of fixed gobos take leaf spring out using finger push the gobos out carefully and insert new gobos For rotating gobos take rotating gobo wheel out by hand push gobos out after pulling out leaf springs Insert new gobos into gobo holders then insert leaf spring back and make sure it is in narrow ring groove in the holder 1 internal ring groove in the holder then flatten it At last use appropriate tool to push tightening spring back then put the holder back into the wheel by another hand Note If the gobo is a glass one it should be touched with glabrous clean and soft tissue or cloth matted between hand and glass instead of with bare hand Close the rear cover and fasten 4 fast fit screws DMX PROTOCOL Short Standard Extended ande mode FUNCTION DMX DESCRIPTION 000 015 No Strobe 1 1 1 Strobe 016 127 Pulse Effect 128 255 Strobe speed from slow to fast 2 2 2 Dimmer 000 255 Dimming from dark to light 0 100 3 Dimmer Fine 000 255 Dimmer in 16 Bit precision 000 031 White 032 047 Cyan 3 3 4 Color Wheel 048 063 Magenta 064 079 Blue 12 21 080 095 096 111 Green 112 127 Yellow 128 159 a Rotation Speed From Slow to 160 223 White 224 255 os Rotation Speed From Slow to 000 207 From big to Small 208 223 Iris effect
4. Tris Linearly adjusted with Macros FOCUS linearly focusing controlled by DMX DIMMER 0 100 linearly adjustable Strobe Electronic strobe 0 3 20 F P S HEAD MOVEMENT Pan 0 540 Tilt 0 270 with auto position correction Swap and Invert functions of Pan and Tilt BEAM ANGLE 16 21 12 36 linear adjustment CONTROL DMXS12 pin 5 pin interfaces 15channels in short mode 19 channels in standard mode and 23 channels in extended mode Master slave mode Stand alone mode Self test mode OTHER FUNCTIONS Adjustable Pan amp Tilt speed Fixture usage time display Software version display DMXS12 wireless available Optional DMX512 wireless remitter HOUSING Composite plastic IP20 WEIGHT 24Kg SIZES See at below LIGHT OUTPUT 17 21 650 36 lux 12 lux 8m 6m 4m 2m Om 2m 4m 6m 8m 9m 2164 12548 541 3137 240 1394 136 185 87 502 60 349 7m 5m 3m 1 1 3m 5m 7m 9m DISTANCE m 12 DISTANCE m 36 DISTANCE m Om Om Om 5m 21 Im 23 18m 10m 22 15m 26 35m 18 21 15m 7 8 23m 20 53m 20 24 29m 12 71m 25m 25 37m 215 88m 30m 6 44m 19 06m 12 36 ELECTRICAL DIAGRAM Power Supply FE Porer Supply me m fale Female SXRL N
5. call a qualified technician Any maintenance work should only be carried out by qualified technicians LUBRICATION To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing it is recommended that the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically preferably every two months Use only high quality high temperature resistant grease instead of any type of oil When lubricating the bearings a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo KEEPING THE PROJECTOR CLEAN To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used in cleaning It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 60 days Do not use any organic solvent e g alcohol to clean the reflector mirror dichroic colour filters or housing of the apparatus TROUBLESHO
6. cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp Hang the fixture on the structure and fasten the screws attached to each clamp See the WARNING on the underside of the base as shown above To pass SAFETY CORD through 1 HOLE for safety Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of each projector WARNING 1 Adevice MUST be lifted or carried by its HANDLES instead of clamps 2 For safety the safety cord should afford 10 times the unit s weight 5 21 POWER SUPPLY MAINS Connect the power cord as follows L live brown E earth yellow green N neutral blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel ofthe projector It is recommended that each projector be supplied separately so that they may be individually switched on and off IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards CONTROL CONNECTION DMX OUT DMX IN DMX 512 PIN FUNCTION 3 PIN cr Sn DATA 3 3 DMX OUT DMX IN ene DMX 512 PIN FUNGTION 5 PIN 5 1 oo 5 DATA 4 2 909 2 4 Ne 3 3 Connection between controller and projector and
7. the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord The projector should always be installed with a secondary safety fixing A safety cord is supplied for this it should be attached as shown in installing the projector section Shields and lens shall be changed if they have become visibly damaged to such an extent than their effectiveness is impaired for example by cracks or deep scratches Exterior surface temperatures of the luminaire after 5 minutes operation is 45 C when steady state is achieved 50 C There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed If you have any questions don t hesitate to consult your dealer or manufacturer Always disconnection from Power before a device s installation cleaning and maintenance 4 21 INSTALL THE Handle Safety cord Clamp N N A Warning Please run the safety cord through a safety cord hole for safety Safety cord hold Operation menu 106 Take 2 clamps and the safety
8. 0060320 1 20 21 LIGHTINGLID 1582 Xingye Avenue Nancun Panyu Guangzhou 511442 China TEL 86 20 3995 2888 FAX 86 20 3995 2330 P N 320020229 Version 20140821 Preliminary 21 21
9. OTING PROBLEM ACTION Check the f th ket The projector doesn t switch on 1 the lamp The lamp comes on but the projector doesn t Make sure that the projector is correctly configurated respond to the controller Replace or repair the DMX cable The projector only functions intermittently Make sure the fan is working and not dirty er Check the lenses are not broken Defective projection Remove dust or grease from the lenses be Make sure the lamp is installed correctly The project image appears to have a halo Carefully clean the optical group lenses and the projector components Check the optics is clean Replace with a new lamp of the specified type and rating TECHNICAL DATA The beam appears dim 15 21 VOLTAGES 100V 240V AC 50 60Hz POWER CONSUMPTION 400W 220V COLOURS 6colors open color wheel With variable speed bi directional rainbow effect Color Temperature 8000K 500K GOBOS 1 Rotating gobo wheel 7 interchangeable gobos white glass or metal gobos can be fixed Indexable bi directionally rotatable and Wheel Scrolling at variable speeds shakable at variable speeds 1 Fixed gobo wheel 7 interchangeable gobos white bi directional wheel scrolling at variable speeds shaking at variable speeds Gobo diameter 27 8mm Gobo image diameter amp 23mm PRISM 1x3 facet prism bi directionally rotatable at variable speeds
10. U 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL DMX Address 1 512 Reset Are You Sure Standard 19 STD 19 Maximm Address 494 DMX Channel mode Short 18 Config Settings Default is STD Short 15 Maximm Address 498 Extended 31 Extended 23 Maximm Address 490 OFF Pan Tilt Swap Default is OFF ON OFF Pan Tilt Invert Default is OFF ON Pan Correction 0 127 Tilt Correction 0 127 XLR First XLR ONLY DMX Mode Default is XLR Wireless Only Wireless First Wireless to XLR Unlink Wireless Yes Slave Master Slave Options Default is slave Master Restore ex factory Defaults yES parameters Transmission yES Language English Chinese Display Mode Off after delay Always on Display Options Display Invert OFF ON Display Contrast 0 18 Power on Time XXXX INFO Information Software version XXX TEST Test Mode Auto Test Yes Manual Test LED NO OFF Colour Wheel White Colour 1 Colour 6 Rotation Stop rotating Reverse Rotation Iris NO Effect 1 Effect 2 Effect 3 F Gobo wheel NO Gobo Gobo 1 Gobo 7 Rotation Reverse Rotation 1 6 Rotating Gobo 1 Gobo 7 Reverse Rotation Shake 176 Gobo rotation Stop rotating Rot
11. ation Reverse Rotation Lambency No Have Prism Set NO Have 10 21 Stop Prism Rotate Rotation Reverse Rotation Focus 0 255 ZOOM 0 255 Pan Location 0 255 Location 0 255 Pan amp Tilt Speed 0 255 DMX Operation Preset Memory User Memory CH1 Strobe 0 255 CH2 Dimmer 0 255 Colour wheel 0 255 CH4 Iris 0 255 mENU CH5 F Gobo wheel 0 255 Operation Mode CH6 R Gobo 0 255 CH7 Gobo R 0 255 Static Scene from 1 16 8 Lambency 0 255 CH9 Prism Set 0 255 CH10 Prism Rotate 0 255 CH11 Focus 0 255 CH12 Zoom 0 255 CH13 Panlocation 0 255 CH14 TiltLocation 0 255 CH15 P amp T Speed 0 255 CH16 Keep Time 0 25 Second Remark 1 synchronous control of multiple projectors parameters be transmitted from the master including DMX mode display setting operation mode user memory data included 2 All projectors Accepting parameters will automatically be set to slave mode Explanations for the logos on top right of the display S Slave M Master D DMX 512 I Preset Memory U User s Memory T Test Mode Lock Logo all buttons are locked press ENTER button for more than 5 seconds till lock logo disappears and buttons are unlocked 11 21 REPLACING GOBOS _ Rotating Gobo Wheel Fixed Gobo Wheel Disconnect the fixture from power Carefully lift off the cover by undoing the
12. between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 5 pin which are included with the projector or 3 pin XLR plugs and sockets The XLR s are connected as shown in the figure above Note care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The projector accepts digital control signals in protocol DMX512 1990 Connect the controller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below amen DMX am J 7 2 N x 7 controller Input Output Input Output Input Output terminator DMX512 6 21 DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply XLR connector with a 1200 ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below DMX TERMINATOR CONNECTION Connect 1200 OHM resis
13. oe Male Female 310 Antenna Vireless Module LED LED Driver Board Atrialli HL320 Prism Focus Motor Driver Tilt Optic Coupling Coupling F Gobo Iris Color Zoom Focus RGobo R Prism Iotor Driver Gobo Ivo Ivo Rotation LED Driver Board Fan BAR Pan Hall Sensor Hall Sensor H Motor Driver Fan Title PR 8163 No VER 1 0 OICHANGE DATA 2014 04 08 ESIGN Trevor lof LIPRINT DATA 2014 04 08 FILE PR 8163 PR A2 COMPONENT ORDER CODES NAME PARTNO QUANTITY REMARK 400W POWER SUPPLY 192010153 1 230W POWER SUPPLY 192010156 1 LED WHITE LIGHT SOURCE 250020279 1 FUSE 270041045 1 5 20 63 250V TILT BELT 290151378 1 HTD 684 3M BELT 290151374 1 HTD 447 3M FAN 030060074 2 92 92 25 030060080 2 60 60 20 1 TIT MOTOR 030040190 1 IRIS MOTOR 1 ROTATING WHEEL MOTOR 030040215 1 PRISM ROTATION MOTOR 1 PRISM MODULE MOTOR 030040230 1 COLOR WHEEL MOTOR 030040155 1 GOBO ROTATION MOTOR 030040166 1 FOCUS MOTOR 2 ZOOM MOTOR clan 2 FIXED WHEEL MOTOR 030040213 1 FROST FILTER MOTOR 030040210 1 CONSTANT CURRENT SUPPLY 230060314 1 PAN TILT DRIVE PCB 230060333 1 MOTOR DRIVER PCB 230060311 1 LCD DISPLAY 23
14. ss 058 and so on Launch the projector Press button more than 5 seconds to unlock panel Press button FUNC to display DMX address Press button UP and IDOWN you can set the address Press button ENTER to confirm after powered next time the last saved settings will be showed Press button FUNG it will return to the upper menu one by one 7 21 STAND ALONE MODE Operate the projector without connecting a controller enable the master mode in the operation panel the projector will run in Stand Alone mode automatically DMX address be set without limitations MASTER SLAVE MODE Many projectors can run synchronously in the Master Slave mode by linking them with each other Select one projector as the master with setting options at any mode of master s modes enabled and make the other projectors as the slaves with setting options slave mode enabled and their DMX start address 001 Using XLR XLR cables Connect the first fixture s output to the second fixture s input and connect the second fixture s output to the third fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below After powered the group will run in synchronous Master Slave Mode I XLR Input Output Input Output Input Output Terminator 8 21 OPERATION MEN
15. tion from slow to fast 10 11 13 Prism rotation 128 191 Stop rotating 192 255 Reverse rotation from slow to fast 11 12 14 Focus 000 255 Linearly focusing 15 Focus Fine 000 255 Focus in 16 precision 12 13 16 Zoom 000 255 Linearly focusing 17 Zoom Fine 000 255 Focus in 16 precision 13 14 18 Pan 000 255 Pan rotation 0 540 15 19 Pan Fine 000 255 Pan rotation in 16 precision 14 16 20 Tilt 000 255 Tilt rotation 0 270 17 21 Tilt Fine 000 255 Tilt rotation in 16 precision 18 22 og 000 255 Pan amp Tilt speed from fast to slow 000 048 Reserved 15 19 23 Control 049 255 Reset Note While prior Channel is used lower channel is invalid 14 21 INDICATION OF LCD Display See ts On DMX signal OK Green LED indication Of No DMX signal Linked with Wireless Transmitter Pue LE Datidication Off Not linked with transmitter Flash Being linked with a transmitter or losing link MAINTENANCE If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification Should these be damaged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not
16. tor 3 across pins 2 and 3 in an XLR plug 1200 and insert into the DMX out socket on the last unit in the chain PIN 2 PIN3 SETUP OPTIONS PROJECTOR CONFIGURATION DMX W DMX PR 8163 XRLED 700 Spot FUNC UP DOWN ENTER A device configuration can be set conveniently via press button switch and LCD display Launch the projector Press button more than 5 seconds to unlock panel LCD display shows functional menus which have their own sub menus for designated functions the below is the details Press button UP or DOWN if you want to browse through the various Setup Options Press button ENTER to save your settings or enter the next menu Press button or DOWN to shift Press button FUNC it will return to the upper menu one by one If you stay for minutes defaulted will show display status automatically TO SET THE DMX START ADDRESS Each projector must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller The fixture have 3 DMX modes There are standard mode extended mode and short mode For example standard mode has 19 channels so set the No 1 projector s address 001 No 2 projector s address 020 No 3 projector s address 039 No 4 projector s addre
17. y improper use will not be assumed by the manufacturer and or dealer ACCESSORIES These items are packed together with the projector Name Quantity Unit Remark G clamps 2 Pcs XLR cable 1 with plug and socket Safety cord 1 Pc This manual 1 Q clamps 2 Pcs Optional 3 21 SAFE USAGE OF THE When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the apparatus The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The projector is only intended for installation operation and maintenance by qualified personnel The projector must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 1 3m I 1 3m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of
Download Pdf Manuals
Related Search