Manuel VR4 FR
Contents
1. available separately Connect a PSU or a 12V battery The 2 pins connector allows internal supply when the board is integrated Diode protection against polarity reversal Waves System 6 V 1 0 2008 ID AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi ID AL remote control handset 6 10 Input on dry contact Connect a push button presence detector smoke heat light or pressure sensor relay output or any type of contact to trigger the player on happening of an event Create a brief contact between SW input and the ground G 12V power supply output to power an external device Input contact SW Ground G Ground G Input contact SW So aa 12V power supply output sw O G 7 SD memory card Insert a memory card in the slot minimum storage capacity 64Mo When inserting or removing the memory card make sure that the player is not powered on 9 GPS extension connector a GPS extension is available as an option This module allows automated broadcast of audio information in relation to the geographical positioning coordinates On request 11 Volume setting volume setting is provided by connecting 2 push buttons on the VOL connector Adjust volume by pressing Volume and Volume buttons Volume button Ground G Volume button G man a 12 Option connector for serial link for future extensions On request2. 13 S PDIF connector To provide a digital audio S PDIF output On request 14 Amplifier The amplifier heats up and it is important to add a cooling device The size of the device must be proportional to the desired power the wall of the case a piece of metal or a purchased cooling device can be used Waves System 7 V 1 0 2008 ID AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi 4 Operating the player and naming of files The NanoPlayer reads files and playback instructions stored on the SD memory card No extra software is required to configure the player Playback options are provided by the way files are named and organized in the directories There are two categories of files 1 Files to be played on powering on the player and played back in loop 2 Files to be played when the input contact is triggered These 2 categories of files are represented by directories or folders Naming of directories results in various playback options Example of use On powering on a chosen file is played and loop When a push button is pressed or when a presence detector is activated the loop file stops and the file associated to the input trigger is played after playing the triggered file the loop file is played again 4 1 Organization of the two directories Only one level of directory is allowed at the root of the memory card Two directories only are permitted Directory names are composed of 3 meaningful
3. been expressly approved by the manufacturer The manufacturer cannot guarantee for the safety or proper functioning of the unit in the case where accessories or consumables are used which are not supplied by the manufacturer The warranty doesn t cover damages caused by use of accessories or consumables which are not supplied by the manufacturer e The manufacturer only regard himself as being responsible for the equipment with regard to safety reliability and proper functioning if assembly re settings changes or modifications extensions and repairs have been carried out by the manufacturer or a company authorized by the manufacturer and if the equipment is used in conformity with the operating instructions written in this manual e The AP103 MicroPlayer complies with the applicable technical safety standards at the date of print All rights reserved for electrical diagrams procedures mentioned names and equipments e No reproduction in whole or in part without the written permission from Waves System A 4 General safety instructions This equipment left our facilities in perfect conditions of operation In order to maintain these conditions for safety and to avoid any risk of injury the user must imperatively follow the safety instructions and read the Warning notes in this manual This equipment manufactured by Waves System has been so designed that any danger is virtually excluded provided it is used according to its purp
4. characters Example ORO or 1S0 55 SDOCARD 1 CD oRO i 150 The 3 meaningful characters are 1 figure 1 letter 1 figure After these mandatory digits it is possible to add a chosen directory name which is ignored by the player but could be useful to identify the content e The ist digit defines the directory number Value 0 or 1 Oxx Directory 0 is the default directory automatically read on powering on the player 1xx Directory 1 is the directory read when the input contact is triggered Example 0S0 Directory N Autoplay directory played on powering on 1R0 Directory N 1 Trigger directory played when the input contact is activated On switching on the NanoPlayer presence of the Autoplay directory N 0 is checked if the directory is present playback of the content automatically starts If the autoplay directory is not present the player goes into stand by mode and awaits for activation of the input contact e The 2nd digit is a letter which defines the playback mode of the directory Directory 0 Oxx has 2 playback modes Directory 1 1xx has the same 2 2 additional playback modes Waves System 8 V 1 0 2008 ID AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi For the default directory read on powering on Oxx xRx R for random mode RND xSx S for sort mode i e playback in a defined order SORT R selects random playback of the files inclu
5. in relation with the required power Waves System 5 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi 1 Speaker Output The NanoPlayer includes a built in amplifier The board can therefore be connected directly onto speakers Connect the speaker wires onto the output of each of the 2 channels Caution Never connect outputs between themselves do not create short circuits and do not use speakers with lower impedance than specified in the player specification Left speaker Right speaker 2 Audio Output on the line level stereo output connect an amplifier sound system mixer or any device providing a line level input The 4 pins connector offers an internal connection link Left output Ground Ground Right output Stereo audio output on mini jack 3 5 3 Luminous indicator a red LED displays the status of the player LED off the player is not powered or in stand by mode LED flashing quickly 2 flashes per second the player is reading LED flashing slowly Error signal for example when memory card is empty 4 8 Power supply If the player is powered with a filtered and regulated power supply unit or a battery the recommanded tension is 12V DC even if the player can be powered between 10V and 15V The current used will depend on the power of the amplifier 5 Infrared The NanoPlayer can be controlled with a infrared remote handset not supplied with the OEM board
6. LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi Audio Line 3 INT gy Il QT interactive Digital NanoPlayer Audio Player MP3 amp Wav MANUAL V 1 0 2008 Waves System ILD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi TABLE OF CONTENTS A Safety instructions ccecceececeeeeeeeneeececeeeeeeneeeeeeaaeesseaeeeseneeeeenaeees P1 B Product information E E P2 1 Product presentation eA P4 2 gt FUNCHONMANTICS cs s c0 ces teste EE A EE aT EEA S ANE AORAR AEAN P4 3 Metallation sriid e eaa iia e eve e ae P5 4 Operating mode and naming of files seeeeeeeeesenesr nern rere nenene P7 5 Configuration file P11 Appendix A Correspondence cescceeeeceeeeeeeeeeeeeeeeeseaeeeteneeeeenaeees P19 ID AL products are exclusively manufactured by Waves System LAVILLE EN BOIS 44830 BOUAYE FRANCE Sales and information 33 2 40 78 22 44 E mail info id al com Web site http Awww id al com Technical department support wsystem com Technical support For a detailed list of technical support options please visit our site www id al com Information in this manual is subject to change without notice and do not represent any commitment from Waves System The equipment described in this manual is supplied under condition of the terms of license specifying the legal use conditions This manual
7. Player accepts variations between 10 and 15V Outside this range the player could be damaged Amplifier output power is determined by the power supply When the line level output is used a 500mA 6W unit is enough to power the NanoPlayer If the integrated amplifier is used a 2A 24W power supply unit minimum is required If the supply unit has insufficient power sound will be very bad and the power unit will heat up and eventually break down Waves System 4 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi 3 Installation 1 Amplified audio output 2 Line level audio output 3 Luminous indicator 4 Power supply 5 Infrared detector 6 Input contact 7 SD card connector 8 Secondary power supply 9 GPS extension 10 Input contact 11 Volume level setting 12 Option Serial link 13 Option S PDIF 14 Amplifier heat dissipation device to be added Memory card choose a good quality card of a minimum size of 64Mo New cards are usually formatted in FAT You can also use FAT32 format for SD card above 512Mo Push the card without forcing To remove push on the card to release it Caution the NanoPlayer does not have any on off switch The player is powered on as soon as it is plugged in The SD card must be inserted or removed when the NanoPlayer is NOT POWERED ON The amplifier heats up It is important to add a cooling device whose size must be
8. afety instructions against risks pertaining to electrical current e The appliance must be connected to a grounded AC power outlet or a correctly wired CEE AC outlet e Before connecting the appliance verify that the power supply voltage and frequency match the specifications indicated on the appliance e Before powering check that the appliance and the cables are not damaged Damaged cables and connections must be immediately replaced e Never leave power cords enter in contact with other cables Handle the power cord and all the cables connected to a power supply with extreme care e Always connect the power supply last Check that the power switch is off before connecting the appliance to mains supply The mains outlet must be accessible after installation e Check the appliance and its power cord from time to time Unplug the power supply if you don t use the appliance anymore or for maintenance e Always grasp only the plug on the power supply cord Never pull the cable to unplug e Power supply repairs and maintenance must be done by qualified personnel e Do not switch the appliance on and off in short intervals as this may reduce its life especially concerning the hard disk Waves System 2 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi A 6 Conditions of use e This product has been designed for indoor use only e If the device has been exposed to drastic temperature flu
9. can t be reproduced or used in whole or in part in any form and by any mean for other use than private without the written permission from Waves System ID AL is a trademark of Waves System Waves System V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi WARNING DO NOT EXPOSE TO MOISTURE AND DUST Unplug the power cord before any intervention FOR YOUR SAFETY PLEASE READ CAREFULLY THIS OPERATION MANUAL BEFORE USING YOUR PLAYER A SAFETY INSTRUCTIONS A 1 CE marking The CE marking is on the ID plate at the back of the product It means this product complies with the low voltage CE directive according the EN 55022 standard and the EMC directive 61000 4 x A 2 Directives e Electro magnetic compatibility EMC and low voltage directive requirements are satisfied A 3 Overview e The user s manual forms an integral part of the unit It must be kept close to the unit Precise observance of these instructions is a pre condition to use the unit for the intended purpose and for its correct operation This user s manual must be passed on to any future purchaser or operator The staff would receive instructions concerning the correct use of the product e Safety for the operator as well as trouble free operation of the unit is only ensured if use is made of original equipment parts Moreover use may only be made of those accessories that are specified in the technical documentation or that have
10. ct On each trigger next file is played chosen in the sequence order of file names sorted in numerical order of the first 3 digits When all the files have been played broadcast starts again with the first file in the list Waves System 9 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi e The 3rd digit is a figure which defines the mode for triggering files This parameter only applies in the trigger directory 1xx This last digit is ignored in the default directory OXX xx0 The trigger directory is launched by an impulse in Non re activation mode a new impulse during current playback has no effect the impulse is ignored xx1 The trigger directory is launched by an impulse in Re activation mode a new impulse stops current playback to broadcast another file xx2 The trigger directory is read as long as the input contact is activated Playback stops when the contact is released 4 2 Organization of audio files included in the directories As for directories file names affect playback pattern e In random mode naming of files is free Only the extension is meaningful name mp3 for MP3 files or name wav for WAVE files In sequential mode i e in sequence order playback mode the first characters of file names must be 3 figures which define the sequence number of the file and therefore its playback order The first 3 figures may or may not be followed by a chosen name Examp
11. ctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature e Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around for your own safety and that of bystand ers B PRODUCT INFORMATION B 1 Correct usage The player is designed for automatically broadcasting audio files Correct usage implies observation of the instructions in this manual as well as observing the require ments concerning installation B 2 Incorrect usage Any other use beyond this is considered as incorrect usage The manufacturer will not be liable for any damage resulting from incorrect usage The operator carries all risks B 3 CONTENT NanoPlayer audio board User manual B 4 TECHNICAL SPECIFICATION Audio Player MP3 and WAV Model NanoPlayer Nominal values for power supply 12V DC B 5 INSTALLATION The apparatus must be set up in a dry and dust free room Do not install the player too close to a wall To avoid overheating the ventilation holes must be kept clear and an air circulation gap must be left above the unit B 6 ELECTRICAL CONNECTION Before use compare mains voltage with that specified on model plate Waves S
12. ded in the directory S selects sequence order playback of the files included in the directory Sorting is done in numerical order of file names which must start with 3 figures followed by complementary characters if desired Some examples 001 my song mp3 002 another song mp3 003 a message wav 004 wav 999 another music mp3 In sequenced order S non numbered files are ignored For the trigger directory 1xx xRx R for random mode RND the WHOLE directory is read randomly xSx S for sequence order SORT the WHOLE directory is read in sequence order xNx N for reading of a SINGLE file only On each trigger the next file is played in RANDOM mode xTx T for reading of a SINGLE file only On each trigger the next file is played in SEQUENCE ORDER R selects random playback of ALL the files included in the directory S selects sequence order playback of ALL the files included in the directory Sorting is done in numerical order of file names which must start with 3 figures followed by complementary characters if desired Some examples 001 my song mp3 002 another song mp3 003 message wav 004 wav 999 another music mp3 In sequence order S non numbered files are ignored N selects ONE FILE playback on each activation of the input contact On each trigger next file is played chosen randomly in the directory T selects ONE FILE playback on each activation of the input conta
13. le 001 my song mp3 or 001 mp3 or 001 wav or Elo song mp3 001 my song wav Note If both numbered and non numbered files are present in the 002 mp3 E3 wav directory only numbered files will be read in sequenced order mode In random mode they will all be read A amp 158 mp3 426 Message Way 5 Infrared remote control The NanoPlayer includes an infrared sensor on the front of the board and can therefore be operated with a IR remote control An optional ID AL infrared remote control handsed is available Waves System 10 V 1 0 2008 ID AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi The ID AL remote handset offers the following controls Transport controls Play Stop Next track Previous track Volume controls Increase Decrease Trigger key Launches the trigger directory as an input contact Waves System 11 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi Appendix A Characteristics Power supply e Nominal voltage 12V DC e Power supply range 10V to 15V DC Consumption on 12V power supply e Stand by 60mA e Reading line level output amplified output not used 95mA e Reading amplifier maximum 8Ohms 2A varies with volume level Output audio power e Voltage 12V THD 10 Charge 8 Ohms 2 x 7W e Voltage 12V THD 0 5 Charge 8 Ohms 2 x 5W Dimensions e Width 70mm Height 18mm e Depth without con
14. nectors 67mm Depth with connectors 80mm Weight 40g Appendix B Functions Audio characteristics e Reads stereo MP3 files MPEG 2 layer 3 44 1KHz from 112kbit s to 320kbits s e Reads CBR Constant Bit Rate files and VBR variable Bit Rate files e Reads stereo Wav files 44 1kHz 16 bits e Volume setting 32 steps SD Memory card e Accepts SD card 64Mo minimum Formatted in FAT16 and FAT32 e Supports long file names e 999 files maximum Interfacing e Status indicator LED e Infrared sensor Play Stop Next Previous Trigger Volume Volume Protocole SONY SIRC 12bits modulated at 38kHz e 1 input on dry contact on Phoenix 3 81mm plug in connector e External power supply connector DC 2 1 5 5 and internal e Various extension connectors Customized applications on request e Stereo output on mini jack and internal connector e Amplified stereo output on screw in terminal block Directory trigger by e 1 input on contact Bounce management 100ms fixed e Infrared remote control Encryption of MP3 files Compatible with encryption software tool v1 or v2 On request Waves System ee V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi Note Waves System V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi Sys AVES http www id al com http www wsystem com Waves System V 1 0 2008
15. ose However for safety reasons we are obliged to point out the following measures Waves System 1 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi e When operating this appliance observe all local rules and enforced regulations The homologation shall be invalid if any modification or alteration is made on the appliance Operating modified appliances may lead to a penal suit In the interest of the safety of work the manager and the operator will be responsible for respecting the instructions e Retain all packing material in case the device must be shipped Take care that it does not fall into the hands of children Only the original packing guarantees optimal safety of the appliance during transport Should it be necessary to ship the product during the guarantee period Waves System will not accept claims for damage arising during the transport from using incorrect packing material e This product is dedicated to broadcasting music It may only be operated by trained or knowledgeable personnel who can handle the device correctly e Before every use the operator must check the functional safety and the condition of the appliance The operator must be knowledgeable in the operation of the appliance e This device must not be used in places with potential explosion risk Moreover it must not be used in an environment favouring combustion neither in a wet or excessively hot or cold place A 5 S
16. ystem 3 V 1 0 2008 LD AL NanoPlayer Lecteur MP3 et Wav autonome Mode d emploi 1 Product presentation The NanoPlayer is an audio player which reads MP3 and WAV files stored on a SD memory card Playback can be automated to read files in loop or when triggered by the input contact The NanoPlayer is a versatile player designed for installations where broadcast of sounds music sound effects or commentaries are required such as museums exhibitions POS displays 2 Functionalities Interactivity The NanoPlayer is interactive i e it can be actioned by an external event by trigger of the electrical contact Autoplay This function is available on the NanoPlayer the player will automatically start playing the selected files on powering on Broadcast mode The way files are organized and named on the SD card fully defines the broadcast mode Digit codes inserted in file names and directory names provide powerful automation of playback patterns Updating By removing the SD card from the player to transfer updates using a card reader on a PC Audio output Two audio outputs are available Line level stereo output on standard 3 5 stereo Mini jack to connect the player onto a sound system and amplified output on screw in terminal block to connect directly onto speakers The ouput power is sufficient for several small to medium sized premises Power supply The player is protected against polarity reversal Caution the Nano
Download Pdf Manuals
Related Search