unit alarm
Contents
1. elentek USER GUIDE Electronic Engineering Technology UNIT ALARM User Manual ELECTRICAL PANEL FOR ALARM SIGNALS UNIT ALARM x UNIT ALAAM ISO 9001 ELENTEK S R L ELENTEK S R L INDICE 1 SYMBOLS AND WARNINGS eu 5 2 GENERALINFORMATI N sous 6 3 WARNINGS ica 7 4 GENERAL DESCRIPTION nn 8 Sa INSTALLA HON aaa 9 6 PANNELLO DI CONTROLLO sauna 10 7 GENERAL OPERATION NOTES isaac etes baneiemtennenanenure 11 8 SETTINGS AND ADJUSTMENTS au unse aaa 12 9 WIRING DIAGRAM asus cil 13 10 STANDARD CIRCUIT DIAGRAN san aiii 14 11 TROUBLESHAOQOTIN insista sinapsis ia 15 12 GENERAL CONDITIONS sau aaa 16 12 1 UO E 16 122 WOO soli ir 16 16 13 DECLARATION OF CONFORMITY 17 ELENTEK S R L ELENTER S R L 1 SYMBOLS AND WARNINGS This operation and maintenance manual uses the symbols outlined below to indicate risks that may arise in the event of failure to observe the instructions supplied This symbol corresponds to an immediate risk of death or serious physical injury or material damage When present take great care to observe warnings DANGER and instructions This symbol corresponds to a possible risk of death or serious physical injury or material damage Take care Failure to observe the instructions in the presence of this symbol may lead to m2. ITALIA hereby declares under its sole responsibility that the machine Trademark ELENTEK UNIT ALARM series complies with the provisions of the following EU directives and subsequent amendments Machinery 2006 42 EC European Directive 2006 95 EC Electromagnetic Compatibility 2004 108 EC and subsequent amendments compliance with the following technical standards e EN 61439 e EN 61000 3 2 EN55014 1 EN 61000 3 3 Piove di Sacco 01 04 2014 LEGAL REPRESENTATIVE Mth ga NOTE NOTE ELENTER S R L elentek Electronic Engineering Technology ELENTEK SRL SOCIETA UNIPERSONALE Via A Meucci 5 11 35028 Piove di Sacco PD ITALIA Tel 39 049 9730367 Fax 39 049 9731063 www elentek com info elentek com P IVA 04534630282 Cod MQ 0006 UK Rev 00 Em 04 2014
3. MODELLO MODEL UNIT aLarm 2 AUMENTAZIONE POWER SUPPLY ON CE MADE IN ITALY KEY TO LUMINOUS INDICATORS AND COMMANDS Green led mains power ON Red led acoustic alarm ON Red led acoustic alarm OFF Button acoustic alarm ON Button acoustic alarm OFF Alarm reset button Manual alarm test button ELENTER S R L 7 GENERAL OPERATION NOTES The UNIT ALARM panel is a unit applicable on any system that requires alarm signals also in the event of a power failure When the 230V power supply is active the led Mains Power ON lights up In this condition the battery inside the UNIT ALARM panel is kept charged automatically with the charge controlled according to the battery level Periodic testing is recommended to ensure correct operation of the panel This is performed by pressing and holding the TEST button to briefly activate the acoustic signal and if present the visual signal When the NC and NO inputs change status NC opens and NO closes the acoustic alarm trips together if present with the visual alarm flashing red light It is possible to set the UNIT ALARM so that the siren shuts off at the end of the alarm condition ALARM RESTORE jumper wired in or that the acoustic alarm continues until the operator intervenes who may either press the RESET button or shut off only the buzzer and the flashing light signals by pressing the MUTE button in which case the red led remains lit
4. Make the earthing connection before all other connections Ensure that the mains voltage is suitable for panel with reference to the specifications on the data plate 1 230V 10 50 60 Hz DANGER If visible cables must be suitably protected The power line must be protected with a residual current circuit breaker sized according to current electrical standards Connect the power cable to ther terminal board IN SUPPLY observing the CAUTION positions L line N neutral and PE earth SCHEDA SO AL IN SUPPLY OUT ALARM IN ALARM INBATTERY OUT 12 Vcc INGRESSO ALIMENTAZIONE USCITA ALLARME INGRESSO INGRESSO 1 230V 10 CUMULATIVA NA NC MAINS INPUT ALARM OUTPUT NO INPUT NC INPUT The NO and NC terminals accept only voltage free contacts as alarm outputs from other panels floats pressure switches etc ELENTER S R L STANDARD CIRCUIT DIAGRAM 10 Z 30 en eq 00 wos MM EQOLELE GHO GE 1960616 GPO GE 191 AJEW 0908S IP BZOGE IZ LL Honey gt UO 2 DI TUS HALN373 Wav TW LINA COW ON ON Wav Tv LNO 71v OS OL ADEZ L HIMOd gt ADEZ L INOIZVLN3WITV OSSIYONI 14 11 TROUBLESHOOTING PROBLEM The panel is powered up but no alarm signals are received The panel is always set to alarm status The flashing
5. to indicate that the fault has not yet been eliminated An internal trimmer can be set within a range of 25 to 120 seconds DELAY TIME trimmer for programmed shutoff of the alarm signals enabled by removing the ON OFF TIMER jumper ELENTER S R L 8 SETTINGS AND ADJUSTMENTS ALARM RESTORE Jumper for automatic reset active the acoustic alarm and flashing light mod UNIT ALARM 2 are deactivated when the cause of the alarm is eliminated If the jumper is not wired in the alarm condition remains until it is manually reset by means of the RESET button ON OFF TIMER Jumper to disable the alarm timer not active the siren and flashing light mod UNIT ALARM 2 continue to operate until the alarm condition is eliminated If the jumper is wired in the alarm condition remains until it is manually reset by means of the RESET button The DELAY TIME trimmer enables the user to set the duration from 20 to 120 after which the acoustic and visual alarm signals are to be shut off if the flashing light is installed automatically In any event the siren can be shut off together with the flashing light mod UNIT ALARM 2 by pressing MUTE To restore operation of the siren and flashing light press ACTIVATE ACOUSTIC ALARM If the siren and flashing light are shut off manually by pressing MUTE but the alarm condition persists the cumulative alarm output continues to indicate the fault ELENTER S R L 9 WIRING DIAGRAM
6. alfunctions and damage to equipment with possible consequent injuries to WARNING the operator Before performing any work on the electrical panel or system shut off the electrical power supply relevant electrical standards Before any other operation ensure the installation is connected to an efficient earthing system A The electrical panel must be connected by a qualified electrician in observance of the ELENTEK S R L 2 GENERAL INFORMATION This manual must always accompany the relevant equipment and be conserved in an accessible location for consultation by qualified technicians assigned for operation and maintenance of the system The installer user is strongly recommended to carefully read all instructions and information in this manual before using the product in order to avoid damage or improper use of the unit which would also render the warranty null and void Before operating the equipment carefully read the manual and follow all instructions herein The information and instructions in this manual refer to the standard use of this product in the event of special circumstances functions or applications not described in this document contact our service centre for assistance If technical assistance or spare parts are required when contacting the manufacturer always specify the identification code of the model and construction number as stated on the data plate Our service centre is available for any requ
7. button e Acoustic alarm shutoff button Internal selector for selection of automatic or manual alarm reset Internal selector for activation of automatic siren shutoff timer e Trimmer for automatic shutdown delay setting Internal sealed battery 12Vdc 1 2Ah Green led Power mains ON Red alarm led e Red led indicating siren shut off e Flashing red light 12Vdc mod UNIT ALARM 2 e Acoustic alarm 90dB 12Vdc e Alarm output NO NC COM resistive load 5A 250V Box in ABS IP55 e Ambient temperature 5 40 C e Relative humidity 50 at 40 C condensate free ELENTER S R L 5 INSTALLATION Ensure that the mains power supply specifications correspond to the voltage specified on the data plate of the electrical panel then make the earthing connection before all other connections 1 230V 10 50 60Hz The power line must be protected by a residual current circuit breaker Tighten the electrical cables on the relative terminals using a suitable tool correctly sized to avoid the risk of damage to the fixing screws Take care if using an electric screwdriver The UNIT ALARM electrical panel is designed for wall mounting using screws and plugs in the pre drilled holes at the corners of the enclosure or by means of brackets when present ELENTER S R L 6 PANNELLO DI CONTROLLO The UNIT ALARM electrical panel has been designed to signal alarms activated via external contacts UNIT ALARM
8. ecialised technician who is fully aware of the relevant current safety standards Always disconnect the unit from the power supply before maintenance or cleaning If UNIT ALARM is not used for prolonged periods store the product in a clean and safe location protected against atmospheric agents and the potential risk of dropping falling In the event of a fire in the place of installation or the surrounding area avoid the use of water jets and use the appropriate extinguishing equipment and means powder foam carbon dioxide Install the equipment far from heat sources and in a dry and sheltered location in observance of the stated protection rating IP The installation of a safety device is recommended to protect the panel power line in compliance with current electrical standards CAUTION Elentek declines all liability in the event of the following Incorrect installation Use by personnel not adequately trained in the correct use of the panel Serious failure to perform scheduled maintenance Use of non original spare parts or parts not specific to the model Unauthorised modifications or interventions Partial or total failure to observe instructions ELENTEK S R L 4 GENERAL DESCRIPTION e Power supply 1 50 60Hz 230V 10 e 1Normally open input for alarm control from voltage free contacts NO 1Normally closed input for alarm control from voltage free contacts NC e Acoustic alarm activation
9. irement or clarification The electrical equipment supplied must be installed indoors in a well ventilated environment within a temperature range of 5 to 40 C N B the information provided in this manual is subject to modifications without notice The manufacturer shall not be held liable for any damage caused in relation to the use of these instructions as they are to be considered guideline only Note that failure to observe the instructions provided in this manual may cause physical injury or damage to objects In any event all local and or current legislation must be observed at all times ELENTER S R L 3 WARNINGS On receipt of the goods perform an inspection immediately to ensure that the equipment has not been damaged during transport If defects or missing material are found the client should promptly notify and in any event within 5 days of receiving the goods our retailer or in the event of direct purchases the Elentek service centre The UNIT ALARM electrical panel must be used exclusively for the purpose and function as specified in design Any other application or use is to be considered improper and therefore hazardous A DANGER No parts of the panel must be disassembled without the official authorisation of Elentek any tampering with or modifications to the unit will render all terms of the warranty null and void All UNIT ALARM panel installation and maintenance operations must be performed by a sp
10. light does not work on the model UNIT ALARM 2 The panel does not work during a power failure No led lights up on the control panel ELENTEK S R L CHECKS SOLUTIONS Ensure that the alarm input is connected correctly on the ALARM IN terminal board Ensure that a jumper is wired in on the alarm input NC if only the NO input is used Ensure correct connection of the terminal board under the flashing light Ensure correct insertion of the bulb in the flashing light if present Check the buffer battery connection observe positive and negative poles Ensure that the FLAT connection with the board inside the panel is inserted correctly On the panel input check that the voltage 230V is present between the mains input terminals L and N ELENTEK S R L 12 GENERAL CONDITIONS 12 1 Warranty The product warranty is subject to the general terms of sale of the company Elentek S r l Acknowledgement of the warranty depends on the strict and proven observance of the operating instructions in this booklet and application of the correct mechanical hydraulic and electro technical practices All products are covered by a warranty valid for 12 months which covers all construction defects of our products and includes the replacement repairs of defective parts The warranty will not be deemed valid in the event of tampering with the panel modifications without prior authori
11. sation faults due to lack of or inadequate protection and or connection errors faults caused by exceeding data plate specifications normal wear and tear failure by installation personnel to observe the specified operating procedures accidental causes natural disasters of any kind such as fires flooding water or lightning The defective material must be delivered carriage paid to Elentek S r l who reserves the right to final judgement of the cause of the said defects The Warranty applies exclusively to restoring the original product characteristics and does not cover material damage or physical injury 12 2 Maintenance UNIT ALARM does not require routine maintenance provided that it is used within the operating limits and in observance of the instructions in this manual Special maintenance or repairs must be performed exclusively by authorised service centres In the event of repairs only original spare parts must be used The manufacturer declines all liability for material damage or injury to persons or animals caused by maintenance interventions performed by unauthorised personnel or using non original materials 12 3 Disposal In the event of disassembly and scrapping strictly observe local legislation regarding pollution Waste disposal according to material categories is recommended ELENTER S R L 13 DECLARATION OF CONFORMITY ELENTEK Srl Unipersonale Via A Meucci 5 11 35028 Piove di Sacco PD
Download Pdf Manuals
Related Search