Home

Polmaddie6 User Manual Issue – 1.0

image

Contents

1. point Polmaddie6 User Manual Issue 1 0 Foreword PLEASE READ THIS ENTIRE MANUAL BEFORE PLUGGING IN OR POWERING UP YOUR POLMADDIE6 BOARD PLEASE TAKE SPECIAL NOTE OF THE WARNINGS WITHIN THIS MANUAL Trademarks Altera Quartusll Max10 and NIOS are the registered trademarks of Altera Inc San Jose California US Polmaddie6 is a trademark of Enterpoint Ltd Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 CONTENTS Foreword 2 Trademarks 2 Introduction 4 Polmaddie6 Features 5 Getting Started 6 Polmaddie Features 7 Power Input 7 Io Headers 8 FPGA 10 Oscillator 10 Leds 11 Switches 12 USB Interface 13 Programming Polmaddie6 14 Mechanical Arrangement 15 Medical and Safety Critical Use 16 Warranty 16 Support 16 Introduction Welcome to your Polmaddie6 board Polmaddie is Enterpoint s low cost product range that offers an economical way to begin programming with FPGAs and FPGAs Polmaddie6 features Altera s low cost MAX10 which is highly flexible and facilitates development of simple microprocessor systems based on Altera s NIOS processor The aim of this manual is to assist in using the main features of Polmaddie6 The Polmaddie board comes in several variants based on different devices Polmaddie6 is based on an Altera Max10 10MO8SAE144C8G FPGA Should you re
2. POL PINaD ES PIN PIN39 N PINI LEFT IO HEADER RIGHT 1O HEADER PIN40 Figure 4 Polmaddie6 Headers The three 40 pin IDC Headers provide a simple mechanical and electrical interface for external signal inputs The connectors on this header are on a 0 linch 2 54mm pitch and allow other electronic circuitry or user designed add on boards to be connected The headers each have 20 IOs routed to the FPGA These are NOT 5V tolerant the maximum input voltage should be limited to 3 3V IO21 is a dedicated Analog input All the other IO can be used as digital inputs or outputs The headers each also have a permanent positive power pin on pin 2 and 19 permanent OV connections as shown below Digital IO Max10 digital IO are either High Speed or Low Speed In the table below High Speed IO are shown shaded blue pins 26 to 119 and Low Speed IO are shaded yellow pins 6 25 and 120 132 More information about the IO specifications and capabilities is available from www altera com http www altera co uk literature lit max 10 jsp Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 1 3 OV OV 5 6 OV 5 6 OV 5 7 8 OV 7 8 OV 7 9 10 OV 9
3. device are available from http www ftdichip com When appropriate drivers are installed the Polmaddie6 USB port should be detected as a serial port Alternative data optimised drivers are also available from FTDI The FT232H is connected to the FPGA and provided a simple UART or other converter is implemented then the data sent over the USB serial port can be used either as control and or data information This allows a host computer to act in a number of ways including system control and data storage functions The FT232H can also supply a clock to the FPGA using the ACBUSS signal This I O can be programmed by tools available from FTDI to output different frequencies or perform other functions The ADBUS 0 3 signals are connected to the JTAG interface to facilitate reconfiguration of the FPGA via USB The connections between the USB device and the FPGA are shown below FT232H PIN FT232H PORT JTAG FPGA PIN FUNCTION FUNCTION 16 CTS TMS 16 19 DCD 58 18 DSR 59 20 RI 57 15 RTS TDO 20 17 DTR 60 13 TXD TCK 18 14 RXD TDI 19 The FT232R connections ACBUSO to ACBUS9 are routed to FPGA FT232R FPGA PIN ACBUSO 56 ACBUSI 55 ACBUS2 54 ACBUS3 52 ACBUS4 51 ACBUSS 27 ACBUS6 46 ACBUS7 45 ACBUSS 44 ACBUS9 43 ITAG_ENABLE Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 14 Programming Polmaddie6 The programming of the FP
4. working 3 Press SW1 This is the left Push Button switch The traffic lights sequence will reset to the beginning of the sequence 4 Press SW2 This is the right Push Button switch The traffic lights sequence will pause until the switch is released Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 Power Input Polmaddie6 is powered either by connecting a 5V power supply to the 2 1mm jack socket or by plugging a cable into the USB socket either from a USB power supply adapter or a PC The 5V supply is used to power the USB interface and to supply a voltage regulator producing 3 3V to power the FPGA the LEDs and the oscillator 3 3V is also available on pin 2 of each of the IO headers If you decide to use this as a source of power for external circuitry please remember that the maximum total power available from the 3 3V Regulator is 2 Amps Top IO Header pin2 POLMADDIEE pe ve oge MT N OE pape 3 3V Regulator zum de gt N Right IO Header pin2 Left IO Header pin2 Power Jack USB Connector Figure 3 Polmaddie6 Power Supply Features WARNING THE REGULATORS MAY BECOME HOT IN NORMAL OPERATION ALONG WITH THE BOARDS THERMAL RELIEF PLEASE DO NOT TOUCH OR PLACE HIGHLY FLAMABLE MATERIALS NEAR THESE DEVICES WHILST THE POLMADDIE6 BOARD IS IN OPERATION Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 IO Headers PIN2 PIN4O TOP IO HEADER PIN1 PIN39
5. 10 OV 9 11 12 OV 11 12 OV 11 13 14 OV 13 14 OV 13 15 16 OV 15 16 OV 15 17 18 OV 17 18 OV 17 19 20 OV 19 20 OV 19 21 22 OV 21 22 OV 21 23 24 OV 23 24 OV 23 25 26 OV 25 26 OV 25 27 28 OV 27 28 OV 27 29 30 OV 29 30 OV 29 31 32 OV 31 32 OV 31 33 34 OV 33 34 OV 33 35 36 OV 35 36 OV 35 37 38 OV 37 38 OV 37 39 1021 3 40 OV 39 40 OV 39 OV OV OV OV OV OV OV OV OV OV OV OV OV OV OV OV OV OV OV these signals have series 470 resistors and 10pf capacitors to ground so they can be used as analog inputs Analog Inputs The Max10 device has one dedicated analog input 1021 and eight optional analog digital IO When they are used for analog signals IO 22 to 29 are single ended inputs connecting to a 12 bit ADC with a maximum sampling rate of IMHz The maximum input voltage is 3 3V More information about the Max10 analog capability can be found in http www altera co uk literature hb max 10 ug_m10_adc pdf from www altera com Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 10 FPGA The main device on the Polmaddie6 is the Altera Max10 10MO8SAE144C8G FPGA Device documentation can be obtained from http www altera co uk literature lit max 10 jsp Oscillator The oscillator on Polmaddie6 is a 3 3V 25MHz ASEM oscillator This clock signal is routed directly through to the FPGA on P
6. GA on Polmaddie6 can be achieved using the Altera tool Quartusll Version 4 0 2 or later is required to program the Max 10 device It is anticipated that a JTAG connection will be used in conjunction with this software There is a single JTAG chain on Polmaddie6 which allows the programming of the FPGA We recommend you use the Enterpoint PROG4 programmer POLMADDIE6 N eve 1 0 FPGA JTAG CONNECTOR Figure 8 Polmaddie6 JTAG The JTAG interface can be enabled to allow configuration to take place or disabled to allow the JTAG pins to function as USB signals or GPIO This functionality is selected using the jumper header J4 With the jumper fitted to the lower two pins JTAG functionality is selected For alternative uses the jumper must be fitted to the upper two pins of J4 This JTAG enable signal can also be controlled via the ACBUS9 signal of the FT232H USB device in which case the jumper should not be fitted The JTAG connector has a layout as follows GND GND GND GND pin1 NC pin14 NC TDI Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 Using the QuartusII programmer the JTAG chain appears like this 10MO8SAES Figure 9 Polmaddie6 JTAG CHAIN Max10 has internal flash memory to hold the configuration data File conversion In the Quartus main menu choose File Convert Programming files COD on File Tools Window Conversion setup files Output programming f
7. elephone 44 0 121 288 3945 Email support enterpoint co uk Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014
8. ile Programming fie type Programmer Object File pof Configuration device EPCE16 File name E TESTING polmaddie PM6 LedTest output_file pof Remote Local update difference file ed NONE Create Memory Map File Generate output_file map Create CvP files Generate output fle periph pof and output_file core rbf Create config data RPD Generate output_file_auto rpd Input files to convert File Data area 4 SOF Data LedTest sof Properties Add Hex Data Page 0 10MOGSAE 144ES Add Sof Page Add File Remove Up Down Properties The Mode drop down menu that defaults to 1 bit Passive serial needs to be changed to Internal Configuration Add your sof file to the dialogue box and choose Generate Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 16 Mechanical Arrangement Dimensions are in millimetres The three 40 way connectors are arranged on a 0 1 inch grid relative to eachother Issue 1 0 www enterpoint co uk 07 JU 1 i H H ema me ls e 2014 Enterpoint Ltd Af EDS TY Mg gs AP pea Rd h z uo gt e ARE n mio Ate H LEDE I AHC H UIE 2 3 Serki No g e o 66 oo oo oo 0 9 o o eo oo 6 Figure 10 Polmaddie6 Mechanical Arrangement The PCB is 1 6mm thick and the tallest component is the power jack which is approximately 11mm high Dimens
9. in 88 which is a clock input Oscillator Figure 5 Polmaddie6 Oscillator Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 11 LEDs Polmaddie6 has 13 LEDs LED 1 is a green power indicator LED and indicates the presence of the 3 3V supply It cannot be controlled by the FPGA LEDs 2 to 13 are arranged in 4 blocks of three each block having one red one orange and one green LED This means they can be used to simulate traffic lights They are all controlled by the FPGA They connect to the FPGA as shown below LED FPGAPIN COLOUR LED10 74 RED LED8 75 ORANGE LED9 76 GREEN LED 13 106 RED LED11 105 ORANGE LED12 102 GREEN POLMADDIE6 ke rr Ed LED 11 Figure 6 Polmaddie6 LEDs Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 12 Switches Polmaddie6 has two push button switches to use these switches the IO pins connected to the switches must have a pull up resistor setting in the constraints file This means that when a switch is activated a low level signal will be detected on the FPGA pin The two switches are connected to the following IO pins ps SW2 Figure 7 Polmaddie6 Switches Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 13 USB Interface The USB interface on the Polmaddie6 is achieved using an FT232H USB to serial UART interface The datasheet and drivers for this
10. ions are subject to manufacturing tolerances Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 17 Medical and Safety Critical Use Polmaddie6 boards are not authorised for the use in or use in the design of medical or other safety critical systems without the express written person of the Board of Enterpoint If such use is allowed the said use will be entirely the responsibility of the user Enterpoint Ltd will accepts no liability for any failure or defect of the Polmaddie6 board or its design when it is used in any medical or safety critical application Warranty Polmaddie6 comes with a 90 return to base warranty Enterpoint reserves the right not honour a warranty if the failure is due to maltreatment of the Polmaddie6 board Outside the warranty period Enterpoint offers a fixed price repair or replacement service We reserve the right not to offer this service where a Polmaddie6 has been maltreated or otherwise deliberately damaged Please contact support if need to use this service Other specialised warranty programs can be offered to users of multiple Enterpoint products Please contact sales on boardsales enterpoint co uk if you are interested in these types of warranty Support Enterpoint offers support during normal United Kingdom working hours 9 00am to 5 00pm Please examine our Polmaddie6 FAQ web page and the contents of this manual before raising a support query We can be contacted as follows T
11. quire a board based on another member of the MAX10 family htto www altera com literature br br max1O brochure pdf 2GSA pos 6 amp WT oss r 1 amp WT oss max10 please contact Enterpoint sales for a guote POLMADDIEG issue 1 0 www enterpointco uk e Mr gt c 2004 Enterpoint Lid ss mde 2 2 an A II II WER Figure I Polmaddie6 Board Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 Polmaddie6 features Top IO Header Push Button Switches wa orikerpoint couk c 2084 Entepoit Lid gs EE ar j ima dors USB Interface Device JTAG Connector Figure 2 Polmaddie6 Features Enterpoint Ltd Polmaddie6 Manual Issue 1 0 20 11 2014 POLMADDIEG USB Connector Max10 FPGA 7 _ Oscillator Right IO Header 12 User LEDs Power Jack Getting Started Your Polmaddie6 will be supplied pre programmed with a traffic lights test design The test design will allow the user to determine that the LEDs and the push button switches of the Polmaddie6 board are working To use this test you should 1 Apply power to the Polmaddie6 board either by connecting a 5V power supply to the 2 1mm jack socket or by plugging a cable into the USB socket either from a USB power supply adapter or a PC 2 The LEDs should light in a traffic lights sequence There is also Power indicator LED which will light to show that power is present and the 3 3V regulator is

Download Pdf Manuals

image

Related Search

Related Contents

    安全データシート  Manual - Omega Bio-Tek  SP300 “Just Infusion” Programmable Syringe Pump  Bedienungsanleitung - La Nordica  CC-QS008 - Rockwell Automation  Cambridge Audio DV30 TV DVD Combo User Manual    PISTOLA 215 MANUAL DE INSTRUCCIONES  

Copyright © All rights reserved.
Failed to retrieve file