Océ User manual - Océ
Contents
1. 32 Adjusting the Print Status 38 Installing for Windows 42 Stowing the Output Stacker 45 If the output stacker arm disengages 47 Contents Chapter 1 Read this first Setup Flow Setup Flow Overview 1 Unpack and Make Sure You Have Everything 2 Assembling the Stand 6 Chapter 1 Read this first Setup Flow 5 Removing the Packing Material 6 Connecting the Power N Stowing the Output Stacker Installing the Printhead 9 Installing the Ink Tanks Bk 10 Loading Roll Media Sep Setup Flow 11 Adjusting the Print Status Run an automatic adjustment of the printhead and media feed amount Information Power Data MAIN MENU Message Adjust Printer Cleaning fo 5 D 3sec OK CD L Or Stop Eject Online Attention For USB connections do not connect the cable before installing the printer driver 12 Installing the Software Refer to chapter 5 Using the Printer in a Network Environment of the User s Guide 8 Chapter 1 Read this first Unpack and Make Sure You Have Everything Unpack and Make Sure You Have Everything Printer Set Printer Power Cable Ink Tanks Bk C PC M PM Y Oa Roll holder oe a LA LL Spool Prevention Stays x 4 Clea2. 2 Securely affix Stand Lower Stay b to Stand Leg R a and Stand Leg L c using 5 hex screws in each side 3 Have 2 people grasp the stand from the left and right sides and lift both sides of the stand simultaneously the same time Lifting one side at a time can cause the stand to warp and create problems in the assembly Attention When you are lifting the stand make sure that you lift both sides at 13 Assembling the Stand 4 Remove the tape that is attached the left and right sides of Stand Upper Stay d 5 Arrange the Stand Upper Stay so that the bends in the brackets on the left and right side e are facing up and the side marked with an R is facing the Stand Leg R a Insert the Stand Upper Stay into the groove between Stand Leg R a and Stand Leg L c 6 Securely fasten the hex screws on the left and right side using the supplied M8 hex driver to fix the Stand Stay in place 14 Chapter 1 Read this first Assembling the Stand 7 Place the Stand in the installation location and lock the front casters 15 Installing the Printer Installing the Printer Illustration gt a a X 1 Remove the box from the printer body and clear out the packing material from above the printer then lift up the base of the printer one side at a time and clear out the packing material from under the printer 2 Fold and then peel off the double sided tape c from the Stand Extensions Boards t
3. keeping both left and right sides level and insert the media into the paper feed slot d and feed the paper until it reaches the paperweight e Once the media reaches the paperweight it is automatically fed through to the platen 13 Close the ejection guide 34 Chapter 1 Read this first 15 16 Loading Roll Media Gently pull on the center of the leading edge of the roll media as far as the ejection guide f and align the right edge of the media with the right edge of the paper alignment line g then lower the release lever Attention Do not pull strongly on the roll media when you align it with the paper alignment line The roll media may not feed out straight in some cases Close the top cover al l Media Type Plain Paper 90 Media Type is displayed You can load the types of media shown in the following table onto the roll holder Set the media type setting to match the type of the media you are using The display only shows the types of paper that can be used with the type of black ink loaded in the printer 35 Loading Roll Media Oc Media name Name Printer Operating Panel IJMO05 Oc Draft Paper Draft Paper IJM020 Oc Standard Paper Standard Paper IJM113 Oc Premium Paper 90g m2 Premium Paper IJM150 Oc SmartMatt Paper SmartMatt Paper IJM215 Oc SmartFitPlus PhotoGloss SmartFit Photo IJM250 Oc Smart Dry Photo Paper S
4. to the human body 26 Chapter 1 Read this first gt gt e Installing the Printhead Attention When you are handling the printhead always hold it by the grips a on the left and right sides Attention Do not touch the nozzles e or the electrical contacts f under any circumstances Doing so may damage the printhead or cause printing problems Attention Never try to re attach the protective caps or packing material that you removed from the printhead Dispose of these parts in accordance with local garbage disposal regulations Insert the printhead into the carriage with the nozzles facing down and the electrical contacts facing the printer 27 Installing the Printhead 9 Push the printhead fixer lever toward the back of the printer and then press down until you hear it click 10 Close the top cover 28 Chapter 1 Read this first Installing the Ink Tanks Installing the Ink Tanks 1 Open the right back cover 3 Gently shake the ink tank 7 or 8 times while it is still in the bag before removing it from the bag Insert the ink tank into the ink tank holder with the ink supply port facing down and the color label facing away from you 77 Attention 29 Installing the Ink Tanks Attention When you are handling an ink tank always hold it by the grips a on A the left and right sides Attention Do not touch the ink supply port b or the electrical contacts c A under any circumstance
5. Oc User manual Oce CS2044 Quick Start Guide Oce Technologies B V 2005 Oc Technologies B V Venlo The Netherlands All rights reserved No part of this work may be reproduced copied adapted or transmitted in any form or by any means without written permission from Oc Oc Technologies B V makes no representation or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Further Oc Technologies B V reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation to notify any person of such revision or changes Edition 2005 10 AB7 5321 V1 Contents Contents Chapter 1 Read this first sssusssuuu untess n e aa 6 sie et ee eee ee 5 Setup FOW wien gs eee ogee BE a we ey ee eed dre eae han ete 6 Unpack and Make Sure You Have Everything 9 Assembling the Stand 13 Installing the Printer ses muet eee deta tin rene ans dues 16 Attaching the Output Stacker 18 Removing the Packing Material 20 Connecting the Power 24 Installing the Printhead 25 Installing the Ink Tanks 29 Loading Roll Media
6. e of the rear surface of the printer inis completes tne printer assembly 23 Connecting the Power Connecting the Power 1 Connect the power cable to the power supply connector in the left side of the printer Le a ys 2 Insert the power plug into the outlet The shape of the power cable varies from country to country oo X 24 Chapter 1 Read this first Installing the Printhead Installing the Printhead 1 Ifthe printer is off press the Power button to switch the printer on Information Power Printer Setup Open UpperCover Cleaning D 3sec 2 Open the top cover Attention Do not touch any areas other than as directed under any circumstances Doing so may damage the printer 3 Pull the printhead fixer lever towards you as far as it will go 25 Installing the Printhead 5 Hold the printhead by the grips a and remove it from the case then remove the protective orange cap 1 b 6 Push the tabs d on either side of printhead protective cap 2 c as shown in the diagram and pull down to remove the cap 69 Do not touch the nozzles e or the electrical contacts f Attention The printhead contains protective nozzle ink If ink leaks it may soil A the printer or peripherals It is recommended that the protective cap 2 c should be removed on the box in which the printhead was packed If ink does leak wipe the ink off with a dry cloth This ink is harmless
7. er of the Administrator group Attention Be sure to use a USB 2 0 standard connection cable Mount the provided User Software CD ROM in the computer CD ROM drive BA rA Q Start the wizard Double click setup exe which you can find on the Oc CS2044 CD rom 1 Oc Printer Driver Setup Wizard Ver2 81 Welcome to the InstallShield Wizard for Oc Printer Driver The Installshield R Wizard will install Oc Printer Driver on your computer To continue click Next 42 Chapter 1 Read this first Installing for Windows 31 Follow the procedure to complete the installation When the port connection screen appears connect the USB cable to the printer and the computer L USB Connection Printer back Computer USB Connecting the LAN Cable Note The following operating systems support a TCP IP network connection Windows Server 2003 Windows XP Windows 2000 Windows Me Windows 98 or Windows NT 4 0 Service Pack 6 or later Attention When this printer is connected to and used on a network switch the A printer on then check the LINK lamp to confirm that it lights and remains on This lamp lights green with a 100 Base TX connection and lights yellow for a 10 BaseT connection Attention Refer to the Chapter 5 of the User s Guide if the connection does A not operate properly 32 Connect the LAN port on the rear of the printer to the HUB port wit
8. h a LAN cable 43 Installing for Windows Installing the Printer Driver 2000 or Windows NT 4 0 you must log in as a member of the Administrator group Attention If you are using Windows Server 2003 Windows XP Windows Attention If you are using Windows NT 4 0 open Network from the Control A Panel in the Start menu and confirm that Microsoft TCP IP Printing is installed and on the list on the Service sheet 33 Connecting the Printer to a Network for the First Time Mount the provided User Software CD ROM in the computer CD ROM drive z 1 34 Start the wizard Double click setup exe which you can find on the Oc CS2044 CD rom The Installshield R Wizard will install Oc Printer Driver on your computer To continue click Next 35 Follow the procedure to complete the installation 44 Chapter 1 Read this first Stowing the Output Stacker Stowing the Output Stacker 1 Grasp the centre of the front output stacker rod a and pull it up slightly 45 Stowing the Output Stacker 3 Lower the output stacker rod a Note To reattach the output stacker perform the steps above in reverse 46 Chapter 1 Read this first If the output stacker arm disengages If the output stacker arm disengages Illustration 47 If the output stacker arm disengages 2 Slide the rotated output stacker arm b in until it clicks into the 2 ho
9. hen stick Stand Extension Board e to the side of Stand Leg R d and Stand Extension Board g to the side of Stand Leg L f 16 Chapter 1 Read this first Installing the Printer 3 Have 4 people grasp the handholds in the base of the printer body then align the side of the printer body h with the line on the Stand Extension Board i and put the printer on the stand 4 Remove Stand Extension Board e and g from the Stand Legs 5 Securely affix the printer body to the stand using 2 hex screws on each side starting from the bottom of the stand backing plate 17 Attaching the Output Stacker Attaching the Output Stacker 1 Insert the Rod Holders c into holes on the back of Stand Leg L a and Stand Leg R b 2 Insert Output Stacker Arm L e and Output Stacker Arm R f into the grooves d in the left and right ends of the Stand Upper Stay then attach them using 2 hex screws 3 Stretch out the Output Stacker fabric such that the white mark g on the fabric is at the front right and the center Output Stacker Rod h is at the back 18 Chapter 1 Read this first Attaching the Output Stacker 4 Attach the Output Stacker Rod j in the center of the Output Stacker fabric to the Rod Holder i and loop the hole in the fabric k over the hook 1 above the Rod Holder Attention Attach the Output Stacker Rods to the Rod Holders in front of the Output Stacker Arm and at the ver
10. les c If the rear output stacker rod d has dropped down fit the output stacker arm b in place before re attaching the output stacker rod 48 Chapter 1 Read this first
11. mart Dry Photo Gloss IJM311 Oc Double Matt Film DM Film IJM138 Oc Transparent Paper 90g m2 Transp Paper 86500 Oc Check Plot Bond Check Plot Bond 86800 Oc Deluxe Bond Deluxe Bond 862024 Oc Premium Color Bond Premium Bond AMPP07 Oc PrintPerfect Alternative PrintPerfect Matte Photopaper GIPPLS7 Oc PhotoPerfect Plus Glossy PhotoPerfect Photopaper PSDRY8 Oc Instant Dry Photopaper Photo Dry 868342 Oc Double Matte Film 4 mil Ink Jet Film 866020 Oc Color Vellum 20 Ib Premium Vellum Media Type HW Coated oo wore An equals 17 Press lt q or p button to select the type of roll media you loaded then press the OK button mark is displayed to the left of the option to show the media type that has been selected and the printer begins preparing to feed the roll media 36 Chapter 1 Read this first Loading Roll Media Attention Always set the Media Type setting to the type of roll media loaded in the printer If the media type setting does not match the loaded roll media printing quality may be reduced 18 Press the lt q or p button to select the setting for the roll media length and then press the OK button Roll Length Set 30 0m When the printer has finished preparing to feed the roll media Online is displayed on the printer display and the printer is ready to print 37 Adjusting the Print Sta
12. ning Brush Hex driver r Printhead Unpack and Make Sure You Have Everything Oc User manual Oc CS2024 Quick Start Guide 2024 Le Quick Start Guide This guide Reference Guide CS Reference Guide User Software CD ROM User Manuals CD ROM Consumables Guide Guide to Mounting the Spool Prevention Stay Warantee Guide to Service and Support Stand Set Stand Legs L and R Stand Upper Stay Stand Lower Stay 10 Chapter 1 Read this first Unpack and Make Sure You Have Everything APT Output Stacker Arms L and R Output Stacker bb Rod Holders x 2 AY m M4 Hex Driver m M8 Hex Driver CL Stand Extension Boards L and R M4 Hex Screws x 18 11 Unpack and Make Sure You Have Everything Installation Space When you are installing the printer reserve a space of the following dimensions or larger 1395mm 33 Width and Depth 12 Chapter 1 Read this first Assembling the Stand Assembling the Stand Caution Have at least 2 people work on assembling the stand Attempting this work alone may cause personal injuries or warp the stand 1 Insert the right side of Stand Lower Stay b all the way into the hole in the side of Stand Leg R a and insert the left side of Stand Lower Stay all the way into the hold in the side of Stand Leg L c
13. s Doing so may cause printing problems or stain the surrounding 30 Chapter 1 Read this first Installing the Ink Tanks 4 Close the ink tank cover until you hear a click 5 Repeat steps to 4 to install the other ink tank colors 6 Close the right back cover after you have installed all of the ink tank colors 31 Loading Roll Media Loading Roll Media Attention When you are handling roll media it is recommended that you wear A clean fabric gloves to protect the printing surface 7 Raise the holder stopper lever a from the axle to unlock the holder stopper and then remove the holder stopper from the roll holder 8 Position the roll so that the leading edge of media is at the bottom and facing away from you then push the roll holder firmly into the media roll from the right side until it is flush with the media core lt a 9 Attach the holder stopper to the left side of the roll holder and insert it until it touches the core of the roll then push the holder stopper lever a down toward the shaft to lock it 32 Chapter 1 Read this first Loading Roll Media 10 Open the top cover and then open the ejection guide 11 Orient the roll holder with the front edge of the roll media facing you then align the roll holder b with the left and right guide grooves c in the roll holder slot and insert the roll holder 33 Loading Roll Media 12 Pull out the leading edge of the roll media
14. s not match the media loaded in the printer you will not achieve the correct print results and the printing quality will be reduced 24 Press the Online button to display MAIN MENU on the printer display Stop Eject Online Omer MAIN MENU Head Cleaning J 25 Press the lt q or p buttons to select Adjust Printer then press the W button MAIN MENU Adjust Printer 26 Press the lt q or p buttons to select Adjust Band then press the W button Adjust Printer Adjust Band 40 Chapter 1 Read this first Adjusting the Print Status 27 Select Standard Adj then press the W button Adjust Band Standard Adj Standard Adj Yes The media feed adjustment pattern is printed The printer scans the printout as it is printing and automatically calibrates the media feed settings for the currently selected media type There are separate media feed settings for each different media type When the calibration is complete the Online lamp turns on and the printer is ready to print 41 Installing for Windows Installing for Windows Connecting USB gt D gt e 29 30 Attention Do not connect the cable yet If you connect the cable now this may prevent the printer driver from installing correctly Attention Make sure that the printer is switched on Attention If your are using Windows Server 2003 or Windows XP or Windows 2000 you must log in as a memb
15. tus Adjusting the Print Status Adjusting the Printhead Position media that you use most frequently Note t is recommended that you run the printhead adjustment using the type of Note f you are using cut sheets load at least one sheet of unused A3 or larger paper not the blank side of used paper in landscape orientation 19 Press the Online button to display MAIN MENU on the printer display Stop Eject Online ONG MAIN MENU Head Cleaning J 20 Press the lt q or p buttons to select Adjust Printer then press the W button MAIN MENU Adjust Printer J 21 Select Printhead Adj then press the W button Adjust Printer Printhead Adj 4 38 Chapter 1 Read this first Adjusting the Print Status 22 Select Advanced Adj then press the W button Printhead Adj Advanced Adj 23 Press the lt q or p button to select Yes then press the OK button l Advanced Adj Yes The printhead adjustment pattern is printed The printer scans the resulting printout as it is printed and automatically calibrates the printhead adjustment values When the calibration has finished the printer returns online 39 Adjusting the Print Status Media Feed Adjustment Attention Before you adjust the amount of media feed you need to configure A the media type setting using the operation panel to match the media loaded in the printer If the media type selection doe
16. y back of the Rod Holder If the Output Stacker Rods are attached to the second rod holder from the back the media will not enter the Output Stacker when ejected and may cause dirtying or damage to the print surface Use the rod holder that is second from the back to temporarily hold the Output Stacker Rod during maintenance 5 Pull out to the back any slack in the paper stacker cloth and then attach the two Output Stacker Rods to the Rod Holders at the very back and front of the Output Stacker Arm 19 Removing the Packing Material Removing the Packing Material 1 Removing the tape and packing material that is attached to the printer body 3 Lift up Release Lever a and remove the protective sheet b from the Platen then lower the Release Lever 20 Chapter 1 Read this first Removing the Packing Material 4 Remove the belt stopper c screws and then remove the warning card that is attached by string and the belt stopper Note The Belt Stopper screw and hex driver are needed for transporting the D printer Store the Belt Stopper that you removed and the tools etc carefully in a safe place 5 Open the ejection guide 21 Removing the Packing Material 6 Remove the Roll Holder and remove the tape and packing material that is attached to the Roll Holder 22 Chapter 1 Read this first Removing the Packing Material 9 Attach the Accessory Pocket to the left sid
Download Pdf Manuals
Related Search