OWNER`S MANUAL
Contents
1. Series Fans Motor Ass y with Ceiling Fan Accessory Weight 22 Ibs fr tire Motor Assembly FPH210 Weight 19 Ibs Motor Ass y with Wall Accessory Weight 27 Ibs Motor Ass y with Pedestal Accessory Weight 29 Ibs Motor Ass y with Floor Desk Accessory Weight 25 Ibs j OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS FANIMATION Important Safety Instructions WARNING To avoid fire shock and serious personal injury follow these instructions 1 Read your owner s manual and safety information before installing your new fan Review the accompanying assembly diagrams 2 Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 3 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing 4 Do not insert anything into the fan blades while the fan is operating 5 Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions 1 To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring and installation procedures must satisfy National Electrical Codes2. centers 4 Position wall bracket on dry wall and mark hole locations 5 Drill two 5 32 pilot holes through drywall into wooden stud 6 Position wall bracket over pilot holes and mount with two 12 x 3 wood screws provided Concrete Wall Installation Note It is recommended that all four mounting holes are used in concrete wall installations Concrete wall anchors are not provided 412 3 Screws 2 Plastic Stud Cap A Wall ST Bracket Ld Plastic Cap Fig 23 Mounting Motor Assembly to Mounted Wall Bracket 1 After you have successfully assembled the Wall Bracket to the wall you are ready to mount the Motor Assembly to the Wall Bracket 2 Secure Hex Bolt and washer to the Wall Bracket Fig 24 3 Position the Motor Assembly onto the Wall Bracket 4 Using a 5 16 x 27 bolt and washer fasten the Motor Assembly to the wall bracket 5 Tighten with an adjustable wrench Do not over tighten 6 Insert plastic screw caps into the four holes on the wall bracket this will hide any screw heads 0 16 x 27 Bolt amp Washer Wall Bracket Motor Assembly Hex Bolt amp Washer 13 Using Your Wall Fan Operating Your Wall Fan 1 Your fan is now ready to operate 1 Check the operation of the fan by turning the speed control to high 2 Plug the fan into a U L approved 120 volt outlet 2 Your fan model is equipped with a 4 position 3 speed control The o
3. Fig 10a NOTE The threaded rods in the hanger bracket serves as guides for easier installation 4 Securely attach the Canopy Housing to the Hanger Bracket using the external lockwashers and knurled knobs supplied with your fan Fig 10b A WARNING To avoid possible fire or shock make sure that the electrical wires are completely inside the canopy housing and not pinched between the housing and the ceiling 5 Push the Motor Coupling cover down until it touches the top of the Yoke Assembly Fig 10c 6 Your Ceiling Fan is now ready for use 1 Restore electrical power to the outlet box by turning the electricity on at the main fuse box 2 Check the operation of the fan by turning the speed control to high 3 Your fan model is equipped with a 4 position 3 speed control The operating sequence is as follows 1 position OFF 2 position HIGH 37 position MEDIUM 4 position LOW 4 Wall Control CH1 and Remote Control CH4 are available as an accessory contact your local dealer for ordering information NOTE If using the Wall Control CH1 or the Remote Control CH4 the 4 position fan speed control MUST be set on HIGH How to Assemble Your Floor Desk Accessory Fan Tool Needed for Assembly e 7 Adjustable Wrench Unpacking Instructions for the Floor Desk Accessory A WARNING Do not install or use fan if any part is damaged or missing This product is designed to use only t
4. 5 16 18 x 2 Bolt PHSHB 25 5 16 18 x 17 Bolt for use with Pedestal Accessory only Floor Desk Unit 18 MOTOR ASSEMBLY MODEL FPH210 tom Description Pant Motor Assembly FPH210 PEDESTAL ACCESSORY MODEL FPH21 tem Description Parti 6 PHFB 5 16 18 x 2 Bolt PHSHB 5 16 18 x 1 Bolt Pedestal Unit 19 MOTOR ASSEMBLY MODEL FPH210 W Description I Parts Motor Assembly FPH210 _ WALL MOUNT ACCESSORY MODEL FPH61 tom Part PHWB Standard Hardware Bag 25 5 16 18 x 17 Bolt for use with m Pedestal Accessory only Wall Unit Hardware Bag PHWUHB Wall Unit 20 Changing the Motor Assembly Position These instructions apply to all four fan models 1 Loosen 5 16 18 x 2 bolt Item 22 on Motor Assembly Position Motor Assembly to desired position and retighten bolt Fig 27 22 23 Fig 27 2 The fans will not oscillate To swivel the direction of the Motor Assembly follow the instructions below 3 Position fan grill to desired position by hand Fan position is limited to 30 forward tilt and 90 backward tilt Fig 28 Loosen side bolts on Motor Assembly Position Motor Assembly to desired position and retighten bolts 30 Forward Tilt 90 Backward Tilt ENEA FANIMATION 10983 Bennett Parkway Zionsville IN 46077 888 567 2055 FAX 866 482 5215
5. ANSI NFPA 70 1999 Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician 3 The fan base must be securely mounted and capable of reliably supporting at least 100 Ibs fan and accessories not to exceed 35 Ibs or 16 kgs Outlet boxes are not acceptable for fan support See page 5 of owner s manual for support requirements Consult a qualified electrician if in doubt 4 CAUTION To reduce the risk of personal injury mount the fan base to a ceiling joist or structural member using the hardware provided with your fan WARNING Support Directly from Building Structure 5 The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades 6 Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not have adequate electrical knowledge or experience have your fan installed by licensed electrician 7 Suitable for use with solid state speed controls WARNING To reduce the risk of fire or electric shock this fan should only be used with Fan Speed Control Part No UC7051R manufactured by Rhine Electronic Co Ltd WARNING TO REDUCE THE RISK OF SHOCK THIS FAN MUST BE INSTALLED WITH AN ISOLATING WALL CONTROL SWITCH WARNING This product is designed to use only those parts supplied w
6. Bolt NOTE If you are uncertain of part description refer to exploded view illustration page 19 Lower Inner Carton Packaging NOTE Place the parts from the Hardware Bag in a small container to keep them from getting lost If any parts are missing contact your local retailer Fig 17 10 How to Assemble Your Pedestal Fan 1 Assemble Column to floor base using 15 16 18 x 1 bolt and washer Fig 18 Do not overtighten 2 After you assembly the column to the floor base you will proceed to mounting your Motor Assembly to the column 3 Secure the Hex Bolt and washer into the top of the column Column Floor Base 5 16 18x 17 4 Bolt amp Washer Fig 18 Using the Pedestal Fan 1 Your fan is now ready to operate 2 Plug the fan into a U L approved 120 volt outlet Speed Control 4 Position the Motor Assembly onto the Column 5 Secure the Motor Assembly with a 5 16 18 x 272 bolt and washer Tighten with an adjustable wrench Do not overtighten 5 16 x 2 Bolt amp Washer Motor Assembly Hex Bolt amp Washer Floor Base Operating the Pedestal Fan 1 Check the operation of the fan by turning the speed control to high 2 Your fan model is equipped with a 4 position 3 speed control The operating sequence is as follows 1 position OFF 2 position HIGH 3 position MEDIUM 4 position LOW 11 How to Assemble Your Wall Accessory Tool Ne
7. Outside U S call 317 733 4113 Copyright 2007 Fanimaton Visit Our Website www fanimation com 2007 01
8. contact a licensed electrician for advice as it must be grounded for safe operation 1 Connect the green grounding lead from the hanger ball the green grounding lead from the hanger bracket to the supply grounding conductor this may be a bare wire or wire with green colored insulation Securely connect wires with wire connector supplied 2 Securely connect the white fan motor wire to the white supply neutral wire using wire connector supplied Fig 9 Securely connect the black fan motor wire to the black supply wire using wire connector supplied Fig 9 After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black leads on the other side of the outlet box Downrod Hanger Ball Assembly Fig 8 Ground Black Fan Wire Wire Green Wire Ground from Hanger Bracket JE oo I I I I Listed Wire u Connector 4 Green Wire Ground from Hanger Ball Black Wire from Fan Motor Fig 9 NOTE Diagram shows wiring for single control of fan How to Wire Your Ceiling Fan cont d A WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until all parts are assembled Noise and fan damage could result 3 Screw in two threaded rods into the Hanger Bracket
9. hanger ball to make sure the clevis pin is properly installed 15 While pulling up on the hanger ball securely tighten the two 3 16 24 x 3 8 setscrews in the downrod sup port Fig 5 NOTE The setscrews must be properly installed as described above or fan wobble will result Setscrew 2 Green MES Ceiling White Canopy Downrod Green Hanger Ball Assembly Black Motor Coupling Clevis Pin Cover Hairpin Clip Motor Assembly Fig 5 16 The fan comes with green black and white leads Before installing fan measure up approximately 6 9 inches above top of Downrod Hanger Ball Assembly Cut off excess wire and strip back insulation 72 from end of wire 17 You have now completed the assembly of your ceiling fan You can now proceed with the hanging and the electrical wiring of your fan WARNING To reduce the risk of personal injury do not insert foreign objects in between the rotating blades Electrical and Structural Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at least 50 Ibs Figure 6 depicts different structural configurations that may be used for mounting the outlet box WARNING To reduce the risk of fire electrical shock or personal injury mount fan to outlet box marked acceptable for fan support and use sc
10. eded for Assembly e 7 Adjustable Wrench Unpacking Instructions for the Wall Accessory Hardware bags WARNING Do not install or use fan if any part is damaged or missing This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with Upper Inner this product by Fanimation Substitution of parts or accessories not designated for use with this Packaging product by Fanimation could result in personal injury or property damage Contact your retail store for missing or damaged parts 1 Check to see that you have received the following Wall parts Bracket Wall Bracket e Standard Hardware Bag Lower Inner 1 5 16 18 x 27 Bolt Packaging 2 5 16 Flat Washers 3 N p 3 Special Hex Bolt 4 5 16 18 x 172 Bolt for use with Pedestal Acc Carton C i e Wall Unit Hardware Bag 1 Two 12 x 3 wood screws 2 Two 5 16 plastic hole caps 3 Two 72 plastic hole caps NOTE If you are uncertain of part description refer to exploded view illustration page 20 NOTE Place the parts from the Hardware Bag in a small container to keep them from getting lost If any parts are missing contact your local retailer Fig 22 12 Mounting Wall Bracket to Wall 1 Determine approximate position of fan 2 Locate stud in your wall 3 For stud installation the top and bottom holes on wall bracket will be used These holes are on 11
11. embly Grommet Power Cord Fig 3 Ya 20 x 12 Bolts 3 Mounting Flange How to Assemble the Ceiling Accessory cont d 10 Remove the rod and thread the third 14 20 x 17 allen head bolt into this hole 11 Tighten the 3 allen head bolts 12 Pass the Downrod Hanger Ball Assembly through the top of the ceiling canopy and push the bell shaped motor coupling cover onto the downrod as shown NOTE You will be using either the 6 downrod sup plied with your fan or an optional downrod purchased separately 13 Separate and untwist the three motor leads Route the motor leads through the Downrod Hanger Ball As sembly A WARNING It is critical that the clevis pin in the downrod support is properly installed and the setscrews are securely tightened Failure to verify that the pin and setscrews are properly installed could result in the fan falling 14 Loosen the two setscrews in the downrod support Align the clevis pin holes in the downrod with the holes in the downrod support Install the clevis pin and secure with the hairpin clip Fig 5 The clevis pin must go through the holes in the downrod support and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull on the
12. ff 3 Motor noise caused by solid state 3 Some fan motors are sensi variable speed control tive to signals from solid state variable speed controls If solid state control is used and motor noise results choose an alternative control method 3 FAN WOBBLES 1 Set screw in downrod support is 1 Tighten both set screws se EXCESSIVELY loose curely in the downrod support 2 Set screw in downrod hanger ball 2 Tighten the set screw in the assembly is loose downrod hanger ball assembly 3 Hanger bracket and or ceiling outlet 3 Tighten the hanger bracket box is not securely fastened screws to the outlet box and or secure outlet box MOTOR ASSEMBLY MODEL FPH210 Tom A Dewmn 7 Pant 1 Motor Assembly FPH210 CEILING FAN ACCESSORY MODEL FPH81 7 Ceiling Canopy Hanger Bracket Assembly 2 D 5 eem 7 i 11 Mounting Flange 1 Ya 20 x 17 allen head bolts 3 14 15 Wire connectors 6 1 72 wire grommet 17 20 x 3 Installation Rod 18 3 16 allen wrench Insert Finish Codes Before discarding packaging material be certain ALL parts have been removed How To Order Parts When ordering repair parts always give the following information e Part Number Part Description e Fan Model Number Contact your retail store for repair parts 16 Ceiling Fan Uni 17 MOTOR ASSEMBLY MODEL FPH210_ _ Motor Assembly FPH210 _ 21 Floor Desk Base Standard Hardware Bag
13. hose parts supplied with this product and or any accessories designated specifically for use with this product by Fanimation Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage Contact your retail store for missing or damaged parts 1 Remove Floor Desk base from carton 2 Check to see that you have received the following parts Floor Desk Base e Standard Hardware Bag 1 5 16 18 x 27 Bolt 2 5 16 Flat Washers 3 3 Special Hex Bolt 4 5116 18 x 17 Bolt for use with Pedestal Acc NOTE If you are uncertain of part description refer to exploded view illustration page 18 NOTE Place the parts from the Hardware Bag in a small container to keep them from getting lost If any parts are missing contact your local retailer Hardware bag Upper Inner Packaging aut ees Floor I VE Desk Base Lower Inner Td Packaging Carton Fig 12 How to Assemble Your Floor Desk Fan 1 After removing the Floor Desk base from the carton place it on the floor with the flat surface resting on the floor Floor Desk Base 5 16 x 2 Bolt amp Washer Fig 13 Hex Bolt 2 Install Hex Bolt and washer in Floor Desk base Motor amp Washer Assembl y Floor Desk 3 Position the Motor Assembly onto the Floor Desk Base base Fig 14 4 Secure Motor Assembly and Floor Desk base with a 2 NE 5 16 18
14. ith this product and or accessories designated specifically for use with this product Using parts and or accessories not designated for use with this product could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade bracket flange or blade holder when installing the brackets balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades LIMITED LIFETIME WARRANTY Extends to the original purchaser of a Fanimation Fan 1 LIMITED LIFETIME MOTOR WARRANTY If any part of your fan motor fails due to a defect in materials or workmanship during the lifetime of the original purchaser Fanimation will provide the replacement part free of charge when the defective fan is returned to our national service center Proof of purchase is required Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement 2 ONE YEAR MOTOR LABOR WARRANTY If your fan motor fails at any time within one year from the original purchase due to defects in materials or workmanship labor to repair the motor will be provided free of charge at our national service center Purchaser will be responsible for labor charges after this one year period Customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs or replacement 3 If any other
15. nties including but not limited to those of merchantability and fitness for a particular purpose to the extent permitted by law Some states do not allow limitations on implied warranties Fanimation will not be liable for incidental consequential or special damages arising out of or in conjunction with product use or performance except as may otherwise be accorded by law This warranty gives you special legal rights and you may also have other rights that vary from state to state 10 A certain amount of wobble is normal and should not be considered a problem or a defect This Manual is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Fan Unpacking Instructions for the Motor Assembly The Motor Assembly you purchased is shipped in a separate carton Follow the unpacking instructions below After completely unpacking the Motor Assembly proceed to the proper section of the manual to assemble the Ceiling Fan Model Wall Model Pedestal Model or Floor Desk Model Owner s Manual A WARNING Do not install or use fan if any part is damaged or missing This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with Upper Inner Packaging this product by Fanimation Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage Contact yo
16. ox is recessed remove wallboard until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall Outlet Box Hanger Bracket 2 Screws and Washers supplied with outlet box Fig 7 How to Hang Your Ceiling Fan cont d 3 Carefully lift the fan and seat the downrod hanger ball assembly on the hanger bracket that was just attached to the outlet box Fig 8 Be sure the groove in the ball is lined up with tab on the hanger bracket Fig 8 4 The Motor Assembly may be oriented to the desired position by loosening the 3 74 20 x 17 bolts located at the top of the mounting flange Fig 4 and rotating the Motor Assembly Be sure to retighten all 3 bolts A WARNING Failure to seat tab in groove could could cause damage to electrical wires and possible shock or fire hazard NOTE Ceiling cover Supply wires and fan wires omitted for clarity A WARNING To avoid possible fire shock do not pinch wires between the downrod hanger ball assembly and the hanger bracket Outlet Box Hanger Bracket How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE Ifyou are not sure ifthe outlet box is grounded
17. part of your fan fails at any time within one year after original purchase due to a defect in materials or workmanship we will repair or replace at our option the defective part free of charge for parts and labor performed at our national service center 4 Because of varying climate conditions this warranty does not cover changes in the finish including rusting pitting corroding tarnishing or peeling 5 This warranty is void and does not apply to damage from improper installation neglect accident misuse exposure to extremes of heat or humidity or as a result of any modification to the original product 6 All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or Fanimation 7 Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty 8 Under no circumstances may a fan be returned without prior authorization from Fanimation The receipt of purchase must accompany authorized returns and must be sent freight prepaid to Fanimation The fan to be returned must be properly packed to avoid damage in transit Fanimation will not be responsible for any damage resulting from improper packaging 9 Itis understood that any repair or replacement is the exclusive remedy available from Fanimation There is no other expressed or implied warranty Fanimation hereby disclaims any and all implied warra
18. perating sequence is as fol lows 1 position OFF 2 position HIGH 3 position MEDIUM 4 position LOW Speed Control 14 Maintenance Periodic cleaning of your fan is the only maintenance that is needed Do not use water when cleaning your ceiling fan It When cleaning use only a soft brush or lint free cloth could damage the motor or the finish and create the to avoid scratching the finish possibility of electrical shock Abrasive cleaning agents are not required and should be avoided to prevent damage to finish WARNING For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1 FAN WILL NOT 1 Fuse or circuit breaker blown 1 Check main and branch cir START cuit fuses or circuit breakers 2 Loose power line connections to the 2 Check line wire connections fan or loose switch wire connections to fan and switch wire connec to the motor assembly tions in the motor assembly CAUTION Make sure main power is turned off 2 FAN SOUNDS NOISY 1 Loose screws in motor assembly 1 Check to make sure all screws in motor housing are snug not over tight 2 Wire connectors inside housing rat 2 Check to make sure wire tling connectors in switch housing are not rattling against each other or against the interior wall of the switch housing CAUTION Make sure main power is turned o
19. rews supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt If your fan is to replace an existing light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture WARNING Turning off wall switch is not sufficent To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock Ceiling Joists WARNING To avoid fire or shock follow all wiring instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician How to Hang Your Ceiling Fan 1 Securely attach the hanger bracket to the outlet box using the outlet box screws and washers supplied with your fan or outlet box Fig 7 2 Pull the electric wires in the outlet box down through the opening in the hanger bracket and bend wires up and out of the way so that the hanger ball will easily fit into the hanger bracket A WARNING The outlet box must be securely anchored and capable of withstanding a load of at least 50 Ibs Hanger bracket must seat firmly against outlet box If the outlet b
20. sed electrician for advice as it must be grounded for safe operation 2 Insert the provided wire grommet into the 77 hole in the Motor Assembly Feed the power cord through the grommet and out the large end of the Motor Assembly Tie a knot in the black power cord approx 18 from the fans motor cover 3 Remove approx 2 of the black outer sheathing on the power cord to expose the 3 colored wires inside Strip the insulation 3 8 from the ends of these three wires 4 Using 3 wire connectors connect the power cord to the provided wire Black Black White White and Green Green 5 Thread the installation rod into one of the 3 threaded holes in the 3 dia x 4 internal disc provided Fig 3 6 Pull the black power cord down through the Motor Assembly until the wire connectors are inside the Motor Assembly housing Fig 4 7 Insert the 3 wires through the center of this disc Then holding the rod at an angle feed the disc through the 2 slots in the large opening in the Motor Assembly Once through the slots pull the disc so that it sits flat against the underside of the lip Fig 4 8 Insert the 3 wires through the center of the mounting flange Now slide the flange over the 74 rod through one of the three bolt holes 9 In the other 2 bolt holes loosely thread two 74 20 x 17 allen head bolts into the disc Fig 4 Green Ground 4 Threaded Rod Internal Disc Green White Motor Ass
21. uncertain of part description refer to exploded view illustration Page 17 Downrod Hanger Ball Assembly Ceiling Canopy Hanger Bracket Motor Coupling Cover Ceiling Fan Hardware Bag Threaded Rods 2 Knurled Knobs 2 External Lock Washers 2 Mounting Flange Wire leads Black White Green 74 20 x 17 allen head bolts 3 Internal 3 dia x 74 disc Wire connectors 6 Y2 wire grommet 10 7 20 x 3 Installation Rod 11 3 16 allen wrench OMNDORWND Upper Inner Packaging N Motor Coupling Sf Cover Ceiling TT Canopy Downrod Hanger Ball Ceiling Fan Hardware bag Lower Inner Packaging Carton Fig 2 How to Assemble the Ceiling Accessory NOTE Proceed to page 8 for Assembly Instructions if you have purchased a Floor Desk Model page 10 for Pedestal Model Assembly Instructions and page 12 for Wall Mount Model Assembly Instructions Prior to assembly set aside and save the hardware bag packed in the upper foam packing If you feel that you do not have enough electrical wiring knowledge or experience have your fan installed by a licensed electrician 1 Cut the black power cord approx 24 from the fans motor cover located on back of motor assembly A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE Ifyou are not sure if the outlet box is grounded contact a licen
22. ur retail store for missing or damaged parts 1 Check to see that you have received the following parts Motor Assembly Owner s Manual Fig 1 How to Assemble Your Ceiling Fan Accessory Tools Needed for Assembly One Phillips head screwdriver One stepladder One 1 4 blade screwdriver One wire stripper hree wire connectors supplied Allen Wrench supplied A WARNING Before assembling your ceiling fan refer to section on proper method of wiring your fan page 6 If you feel you do not have enough wiring knowledge or experience have your fan installed by a licensed electrician Materials Wiring outlet box and box connectors must be of type required by local code The minimum wire would be a 3 conductor 2 wire with ground of the following size Installed Wire Length Wire Size AWG Up to 50 ft 14 50 100 ft 16 Unpacking Instructions for the Ceiling Fan Accessory A WARNING Do not install or use fan if any part is damaged or missing This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with Substitution of parts this product by Fanimation or accessories not designated for use with this product by Fanimation could result in personal injury or property damage Contact your retail store for missing or damaged parts 1 Check to see that you have received the following parts NOTE If you are
23. x 272 bolt and washer LJAN TH 5 Tighten with adjustable wrench Do not over tighten Fig 14 Using the Floor Desk Fan Operating the Floor Desk 1 Your fan is now ready to operate Fan 2 Plug the fan into a U L approved 120 volt outlet 1 Check the operation of the fan by turning the speed control to high 2 Your fan model is equipped with a 4 position 3 speed control The operating sequence is as follows 1 position OFF 2 position HIGH 37 position MEDIUM 4 position LOW Speed Control How to Assemble Your Pedestal Accessory Fan Tool Needed for Assembly e 7 Adjustable Wrench Unpacking Instructions for the Pedestal Accessory Hardware bag WARNING Do not install or use fan if any part is damaged or missing This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with Upper Inner Packaging this product by Fanimation Substitution of parts or accessories not designated for use with this product by Fanimation could result in personal injury or property damage Contact your retail store for missing or damaged parts NOTE Column is not included and is sold seperately Floor 1 Remove base from carton 2 Check to see that you have received the following parts Floor Base e Standard Hardware Bag 1 5 16 18 x 272 Bolt 2 5 16 Flat Washers 3 3 Special Hex Bolt 4 5 16 18 x 17
Download Pdf Manuals
Related Search