TS-590S USB Audio Setting Manual
Contents
1. check the settings and try the test again 13 a From the ARUA 10 window click the Save button to complete the setup 10 14 From the ARUA 10 window click the Close button to close the window 15 Right click on the E icon in the task tray to display the menu From the menu select Start The icon in the task tray changes to and ARUA 10 starts 11 5 Limitations IMPORTANT 5 1 USB Port Connectivity Limitations If the PC and TS 590S are connected via a USB cable audio transmissions can be transmitted using the USB audio function In principle however there is a delay with USB audio signals plus sound may be delayed or lost depending on the PC performance and load status Therefore do not perform operations for which delays are likely to be a problem such as contests or communications requiring quick responses Also when connected with the USB cable alert sounds from other software or audio from music or videos may not play over the computer speakers Furthermore when the DATA VOX function of the transceiver is ON and the computer and transceiver are connected with the USB cable the transceiver may send sounds emitted by the computer To avoid unintended transmissions when the computer and transceiver are left connected via USB set the DATA VOX function to OFF Depending on the combination of PC and sound functions the USB audio function may not operate correctly JVC KENWOO2. such as contests or pile ups requiring quick responses for which delays are likely to be a problem Refer to Chapter 5 Limitations for other limitations To use the USB audio function knowledge not only of transceivers but also of computers is required JVC KENWOOD does not offer support for purchasing computers or for customer s computers JVC KENWOOD Corporation shall bear no responsibility for related damage such as damage caused by missed communications and dialog opportunities due to incorrect customer settings nonconformances or misoperations as a result of using this document or the ARUA 10 software 2 Operation Using the USB Audio Function Operation using the USB audio function is explained using the diagram below Flow of the Signal Sound Device Diagram 1 Operation Using the USB Audio Function The left side of the diagram shows the TS 590S unit while the area in the square on the right side indicates the computer The TS 590S and the computer are connected by a USB cable The microphone and speakers connected to the computer are shown on the far right Audio reception is explained first Incoming audio from the TS 590S is sent to the computer via the USB cable and played over the speakers connected to the computer A signal pathway on the computer to connect the USB audio device input signals and output from the audio device connected to the speaker is necessary Audio transmission is explained next Audi
3. the VOX function for the audio output from the rear terminal Menu No Function Set value 69 Data VOX ON or OFF The default setting is OFF Caution gt When this function is ON all sounds created by the computer other than the intended audio transmissions are also transmitted so be careful gt When using this function for the first time we recommend connecting a dummy load to the TS 590S to perform checks and adjustments 4 1 5 Data VOX Delay Time Setting Set the VOX Delay Time Setting when using the Data VOX function Menu No Function Setting range 70 Data VOX delay time 0 to 100 The default setting is 50 4 1 6 Data VOX Gain Setting Set the VOX Gain Setting when using the Data VOX function Menu No 71 Function Setting range 0to9 Data VOX gain for the USB audio input The default setting is 50 4 1 7 Allocating DATA SEND Functions to PF Keys Set the DATA SEND functions to the PF keys to test the transmission of audio input from the rear terminal In this example the PF A key has been set Menu No Function Set value 79 Front panel PF A key assignment 205 The default setting is 200 VOICE1 Using the PF keys which set the DATA SEND functions enables switching between transmit and receive modes for audio input from the rear terminal 4 2 Setting to Transmit an US
4. B Audio Input The SEND keys on the PTT of the microphone connected to the TS 590S and on the TS 590S control panel are the method for transmitting audio input to the microphone connected to the TS 590S so even if these operations are implemented audio entered as audio signals from USB cannot be transmitted To transmit audio input as audio signals from the USB select one of the following methods Transmitting using the ARCP 590 With the ARCP 590 settings must be done to transmit audio input through the rear terminal to use the on screen SEND key Select Setup TX control from the ARCP 590 Tool menu The Setup TX control window is displayed In the window above select ACC2 USB in the Modulation line setting and then select USB For further details refer to the ARCP 590 help ARCP 590 details are downloadable from the KENWOOD website Use the ACC2 Connector s PKS port to transmit This setting allows you to transmit audio received by the rear terminal by setting the PKS port in the ACC2 Connector on the back of the TS 590S to Low For details of the connector and terminal specifications refer to the TS 590S instruction manual Use the PF key assigned to the DATA SEND function to transmit By assigning the PF key to the DATA SEND function the PF key can be used to transmit audio received by the rear terminal For details refer to 4 1 7 Allocating DATA SEND Functions to PF Keys 4 3 ARUA 10 Sett
5. D does not offer support for customer computers 12 6 Frequently Asked Questions This section introduces questions that have been asked to date and subjects verified by JVC KENWOOD Corporation Question Answer Installation Where can get the USB audio drivers You do not need to download the drivers When the computer and TS 590S are connected via USB for the first time the standard driver for your operating system is automatically installed There appear to be many limitations Is it actually possible to operate using the USB Audio Function Although it may not run exactly the same if you get used to it general communication on a practical level is possible The point is to become accustomed to the delays particular to USB audio You may have some initial confusion with issues like the standby timing Can use a USB or Bluetooth headset You can use a USB or Bluetooth headset However due to unavoidable delays using these devices it takes time for spoken audio to be transmitted Also time is required for received audio to reach the headphones We do not recommend use of these devices when such delays can cause problems Operation There is static in the audio transmissions Audio transmission and reception levels are low The USB audio input output levels are not appropriately set Please adjust the settings via Menu Nos 64 and 65 on the TS 590S This may also d
6. KENWOOD TS 590S USB Audio Setting Manual JVCKENWOOD Corporation October 31 2014 CONTENTS 1 About the TS 590S USB Audio Function 2 2 Operation Using the USB Audio FUNCTION eee eeceeeeececeeeeeeeenneaeeeeeeeeeeeeteeneaeeeeeeeeeey 3 3 Installing the ARUA 10 Software cece ccceceeeeeeeeeneeneeeeeeeeeeeeeeeaeaeeeeeeeeeteennaaeeeeeeeerey 4 3 1 System REQUINGMOMINS sssrini eese ney sers dise sata aaie aiaa Daai anaita 4 92 lnstallation sesen a a E aE 4 3 3 About Virtual COM Port Driver 4 SOM O E E E T E E N A 6 4 1 Transceiver Settings srei ie iiiki e aape iaa raai red aea ne aaeei eevesteveesiae 6 4 1 1 Setting Up an Audio Input Route from the Rear Terminal 6 4 1 2 Audio VO Level Settings 6 4 1 3 Mixed Beep Setting to External Audio Outputs 6 4 1 4 Data VOX SOWINGS eniti ere dada tes ei eee lente se ad rene c teste 7 4 1 5 Data VOX Delay Time Settings 7 4 1 6 Data VOX Gain Setting is 7 4 1 7 Allocating DATA SEND Functions to PF Keys 00 eeeeeeeeeeeneeeeeeeeeeeenenneeeeeees 7 4 2 Setting to Transmit an USB Audio Input ee eeenneaeeeeeeeeeeeeeeeaas 8 4 3 ARUA 10 SOUlinQS ws codecccecctesecievg de ane ceevetens EnaA AEE Aa Peer tenais ets 9 5 Limitations MPORTANT Miss isa ones A se ne 12 5 1 USB Port Connectivity Limitations eee eee cree eee eeeneaeeeeeeeeeeeennnaeeees 12 6 Frequently Asked QUESTIONS 0000 0 eee cece teeteee ce
7. KENWOOD website http www kenwood com i products info amateur software_download html When connecting the TS 590S to a computer using a USB cable for the first time drivers required for the USB Audio Function are automatically installed If you are using an ARCP 590 and Computer Control Command you must install the Virtual COM port driver to connect the TS 590S with a USB cable Download and install the driver from the following KENWOOD website http www kenwood com i products info amateur software_download html 3 3 About Virtual COM Port Driver When connecting the TS 590S to a computer with a USB cable for the first time the New Hardware Detected Wizard message appears This is the install prompt for the Virtual COM Port If you are not using an ARCP 590 or Computer Control Command there is no need to install the Virtual COM Port However if it is not installed the Wizard message appears every time the USB cable is connected so we recommend installation When the New Hardware Detected Wizard message appears and you have not yet installed the Virtual COM Port click Cancel and install the Virtual COM Port before continuing For details on how to install the Virtual COM Port please visit the download page noted above 4 Settings 4 1 Transceiver Settings Complete the necessary transceiver TS 590S settings before using the USB audio function Refer to the user manual for how to use the TS 590
8. S 4 1 1 Setting Up an Audio Input Route from the Rear Terminal On the rear terminal there are two types of audio input routes the ACC2 connector route and the USB connector route for using the USB audio function Make the following menu settings to transmit audio input from the USB connector Menu No Function Set value 63 Audio input line selection for data USB communications The default setting is ACC2 4 1 2 Audio I O Level Settings Use the following menu to adjust audio transmission input levels from the PC and receive audio output levels to the PC Menu No Function Setting range 64 Audio level of USB input for data 0to9 communications 65 Audio level of USB output for data 0to9 communications The default value for all settings is 4 4 1 3 Mixed Beep Setting to External Audio Outputs With the TS 590S default mode only received audio signals that do not include beeps or side tones are output as audio signals from the ACC2 connector and the USB connector as USB audio signals Make the following menu settings to output the same audio as the audio output from the wireless speaker including beeps and side tones externally Menu No Function Set value 68 Mixing beep tones for ACC2 USB audio ON outputs The default setting is OFF Reference To implement data communications turn this function OFF 4 1 4 Data VOX Settings Set whether or not to use
9. ce teen eeeeaaeaeeeeeeeeeteeaaaaeeeeeeeeeeesetneaeeeeeeees 13 Disclaimer All efforts have been made regarding the accuracy of the contents described in this document However there is a possibility of misprints and of descriptions that may cause misunderstanding JVC KENWOOD Corporation bears absolutely no responsibility for damages arising thereof JVC KENWOOD Corporation may revise and amend the products information described in this document without notice JVC KENWOOD Corporation bears absolutely no responsibility for damages arising thereof Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries Bluetooth is a registered trademark or trademark of Bluetooth SIG Inc The names of all products described hereafter are the trademarks or registered trademarks of their respective manufacturers and are omitted throughout the text 1 About the TS 590S USB Audio Function When the TS 590S is connected to the computer using a USB cable the USB audio function can be used to play incoming audio over the computer speakers and transmit audio from the computer microphone This setup guide explains how to set up the TS 590S to use its USB audio function and how to use the ARUA 10 software to control input output routes of the USB audio signals from a computer Important gt USB audio may be delayed due to unavoidable principles Consequently do not perform operations
10. epend on the specifications of the sound device used in your computer Try using another sound card or USB sound device The sound device driver may need to be upgraded Try checking for new versions and upgrade the driver 13 cannot hear audio from the transceiver over the computer speakers It is possible that the USB audio output level from the TS 5908S is too low Try adjusting Menu No 65 If there is a mistake in the ARUA 10 settings audio reception sent by USB audio to the computer is not played from the computer speakers Refer to 4 3 ARUA 10 Settings and check the settings The volume setting of the computer speakers or headset may be too low Try adjusting the volume settings Operation Even though the transceiver is in transmission mode cannot transmit voice input from the computer microphone If the audio input route from the rear terminal of the TS 590S is set to ACC2 USB audio input received by the TS 590S is not transmitted Refer to 4 1 1 Setting Up an Audio Input Route from the Rear Terminal and check the settings When transmitting using the TS 590S microphone PTT or SEND key USB audio received by the TS 590S is not transmitted When using the ARCP 590 the Transmission Controls Settings are required Refer to 4 2 Setting to Transmit an USB Audio Input and check the settings If there is a mistake in the ARUA 10 setti
11. he left side of the window set the Modulated Input in the Transceiver section This is where the output is set for sending audio transmissions to the transceiver As transmissions are sent to the transceiver as USB audio select Speakers USB Audio Codec 6 Inthe third section from the left side of the window set the Microphone in the PC section This is where the computer microphone used for audio input to be transmitted is set In the above example Microphone High Definition Audio is selected 7 On the far right of the window in the PC section set the Speakers device This is where the computer speakers used for playing incoming audio are specified Clicking the RX AF Test button plays a test signal from the selected speaker Next follow the steps below to confirm that the intended audio transmission route is configured 8 Connect the dummy load to the TS 590S 9 Ifthe TS 590S is in Split mode switch to Simplex mode with the mode set to SSB USB or LSB 10 Enable the transmission monitor function a 11 x Press the PF key set to the DATA SEND function to transmit 12 From the ARUA 10 window shown above click the TX AF Test button If test signals are played from the internal TS 590S speakers the system is set up correctly Push the PF key set to the DATA SEND function to return to audio reception mode If the test signal does not play
12. ings Follow the steps below to set up the ARUA 10 1 2 3 Connect the TS 590S and computer using a USB cable To launch the software select Start Button gt Programs gt Kenwood gt ARUA 10 After launching the ARUA 10 a Task Tray icon appears Right click this icon and select Device Settings from the menu The window shown below appears r Xx Gi Settings ef Settings a New Setting Setting Name 75 5905 Device Other Transceiver PC Microphone Speakers When you output a test sig take care about volume In this window you can specify sound devices for the transceiver s audio reception output and modulated audio input You can also specify which microphones and speakers connected to the computer to use In the above example the computer has recognized four types of input sound devices Microphone USB Audio Codec Microphone High Definition Audio Line In High Definition Audio There are two types of output sound devices Speakers USB Audio Codec Speakers High Definition Audio The items listed depend on the operating system and sound devices used 4 On the far left of the window from the Transceiver section set the Reception Output This is where the input is set for audio received from the transceiver As audio reception comes into the computer as USB audio select Microphone USB Audio Codec 5 Inthe second section on t
13. ngs USB audio input to the TS 590S is not transmitted Refer to 4 3 ARUA 10 Settings and check the settings If the computer microphone or headset is muted audio is not sent from the computer Please check your computer s sound function settings 14 The transceiver does not transmit VOX when audio input is from the computer microphone In order to transmit VOX when voice data input is received through the rear terminal specific menu settings are required Refer to 4 1 4 Data VOX Settings and 4 1 6 Data VOX Gain Setting and check the settings Operation The end of audio transmissions are cut off The system switches back to audio reception before sending all of an audio transmission When using the ARCP 590 if you quickly switch to receive mode after using the computer s microphone to transmit you may have switched before the audio is transmitted because of the delay in transmitting an audio signal via USB If this happens it may be possible to avoid such delays by slightly changing the method of operation as described below After transmission watch the power and ALC meters and wait until the audio input to the transceiver finishes before switching back to reception mode Use the DATA VOX function Use a regular stereo jack instead of a USB or Bluetooth headset 15 Question Answer Operation The transceiver transmits even
14. nt to be able to hear them but can t 16 This can be configured in the transceiver menu Please refer to 4 1 3 Mixed Beep Settings to External Audio Outputs Question Answer Other FAQs Is ARUA 10 required when using KNS remote operation over a network Using the USB Audio Function while operating the TS 590S the computer s standard audio can no longer be heard ARUA 10 cannot be used with KNS remote operation over a network When operating ARUA 10 audio reception from the transceiver is played over the computer speakers If you want to stop audio reception stop the ARUA 10 operation Also when not using the TS 590S we recommend you disconnect the USB cable from the computer 17
15. o input from the microphone connected to the computer passes through the USB cable and is transmitted by the TS 590S unit A signal pathway on the computer between input signals from the audio device connected to the microphone and output from the USB audio device is necessary The ARUA 10 software serves as a bridge for these signal paths within the computer The ARUA 10 software lets you select which speaker and microphone are used for transceiver operations when there are multiple speakers and microphones connected to the computer 3 Installing the ARUA 10 Software 3 1 System Requirements In order to use the ARUA 10 software your computer must meet the following requirements Chart 1 Computer Requirements Category Specifications CPU CPU must exceed performance recommended for your operating system MEMORY System memory must exceed that recommended for your operating system HDD Over 100 MB free space CD ROM DVD ROM Drive Not required USB Port When using the system described above a single USB 2 0 port Input Output Devices Keyboard mouse microphone speakers Display XGA 1024 x 768 or above Sound function Required OS Windows Vista SP2 or later 32 bit only Windows 7 SP1 or later 32 bit or 64 bit Windows 8 RTM or later 32 bit or 64 bit Windows 8 1 RTM or later 32 bit or 64 bit 3 2 Installation Download and install the ARUA 10 software from the following
16. with no voice input from the microphone when the DATA VOX function is set to ON Turning the DATA VOX to ON causes the transceiver to transmit even when the microphone is not connected The transceiver transmits without my knowledge When the DATA VOX function is ON for laptop computers with internal microphones sounds near the computer that are loud enough to trigger the VOX are sent to the transceiver and transmitted by VOX Or sounds from other software may be sent to the transceiver and transmitted by VOX Please try the following Refer to 4 1 6 Data VOX Gain Setting and adjust the VOX Gain Use a headset While operating the transceiver do not use other software If the above methods do not work turn OFF the DATA VOX function Also when the computer is left connected to the transceiver using the USB cable sounds from other software such as alerts music and video are transmitted to the transceiver and sent by VOX unintentionally If you leave the computer and transceiver connected using a USB cable please turn OFF the DATA VOX before using your computer Reception quality depends on the device Voice audio is affected by voice encoding and the quality may differ from the original voice reception quality This is part of the USB sound function specifications and is unavoidable can hear the beeping and voice guidance audio from the transceiver on the computer Alternatively wa
Download Pdf Manuals
Related Search