User Manual - Accurate Technology, Inc.
Contents
1. 2 Touch a grounded metal surface to discharge any static electricity from your body and then remove the front and back cover of the Transmitter enclosure Slide out the coin cell battery from the battery holder and set it aside Locate the address switch in the lower left hand corner of the circuit board Set the desired channel using the dip switch The table on the page 9 illustrates the switch setting versus the channel number ACCURATE TECHN RF Channel Switch CHANNEL LEARN Accurate Technology Inc Page 7 of 16 5 Reinstall the battery into the battery holder PLUS side is UP When the battery is installed the two LEDs on the front of the Transmitter will both flash momentarily then go out NOTE If the LEDs continue to flash on and off remove the battery for 10 seconds and then re install it 6 Install the circuit board into the enclosure and secure with the two Phillips head screws ProRF SPC Transmitter User Manual Page 8 of 16 RF Channel Switch Settings RF Channel SW 1 SW 2 SW 3 SW 4 0 ORE OFF OIF OFF 1 ON OFF OIF OFF 2 OFF ON ORF OFF 3 ON ON OFF OFF 4 ORE OFF ON ORF 5 ON ON OFF 6 OFF ON ON OFF 7 ON ON ON OFF 8 OFF OFF OFF ON 9 ON OFF OFF ON 10 OFF ON ORF ON 11 ON ON OFF ON 12 OFF OFF ON ON 13 ON ORR ON ON 14 OFF ON ON ON 15 ON ON ON ON Connecting the Transmitter The ProRF SPC Tr2. Accurate Linear Digital Measuring Systems Firmware version 1 0 and greater FCC NOTICE This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the Receiver e Connect the equipment to an outlet on a circuit different from that to which the Receiver is connected e Consult the dealer an experienced radio television technician for help Operation with non approved equipment is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user s authority to operate this equi
3. END button on the DRO The DRO LCD will display Snd for 1 second If the transmission is successful the MSG SENT LED on the SPC Transmitter will flash very briefly about 1 10 second The ProRF Receiver will momentarily display the Transmitter ID along with a flash of the POS MSG LED SEND button location depends on DRO version TRANSMITTER ID Transmitter ID Displayed If the transmission was not successful the MSG SENT LED on the SPC Transmitter will flash for a longer time about 1 1 seconds If this occurs the user should try to retransmit again by pressing the SEND button on the DRO the error continues a range issue or interference may be preventing the transmission from being received Move the DRO closer to the Receiver and attempt the transmission again Each time the SEND button on the DRO is depressed the SPC Transmitter will send a new position message to the Receiver The user can also activate a special delete function that will transmit a special message to the ProRF Receiver This message will cause a delete last measurement signal to be sent to the PC or TigerStop In the case of a PC it causes a DELETE text message to be displayed When using a TigerStop it causes the last entry in the cut list to be deleted To activate the delete function press the F2 button on the DRO NOTE The delete function only operates with ProScale DROs that have firmware version 2 x9 or above Battery Replacement
4. Periodically the coin cell battery in the SPC Transmitter will require replacement A low battery condition is detected by the Transmitter and will be indicated by flashing the LOW BAT LED when a position message is sent A low battery condition still allows normal operation but the transmission range may be diminished Change the battery as soon as possible by completing the following 1 2 Unplug the SPC Transmitter from the side of the ProScale DRO Using a Phillips screwdriver remove the two screws from the back of the housing Touch a grounded metal surface to discharge any static electricity from your body and then remove the back cover of the Transmitter enclosure Slide out the coin cell battery from the battery holder Install a new CR2450 or equivalent lithium battery into the battery holder with the PLUS side UP When the battery is installed the two LEDs on the front of the Transmitter will both flash momentarily NOTE If the LEDs continue to flash on and off remove the battery for 10 seconds and then re install it Re install the rear enclosure cover and replace the screws Plug the SPC Transmitter into the DRO s SPC data port ensuring the pins are correctly aligned ProRF SPC Transmitter User Manual Page 14 of 16 Product Registration Fill out for your records and FAX to Accurate Technology 9 1 828 654 8824 Or register online at www proscale com registration htm Name E Mail Company Add
5. Transmitter as a system i e with a ProRF Receiver the Receiver and Transmitter s have already been associated at the factory during final testing If you have purchased this Transmitter separately you will have to associate it with your ProRF Receiver The association procedure is outlined below Additional information regarding this operation can also be found in the ProRF Receiver user s manual Associating Transmitters amp Receivers To associate one or more Transmitters with a Receiver complete the following 1 Connect to the ProRF Receiver using HyperTerminal or other terminal emulation program as described in the ProRF Receiver user s manual Enable Transmitter association by issuing the command 1 lt ENTER gt The Receiver will indicate that learning is enabled Insert a bent paperclip into the hole on the face of the SPC Transmitter labeled PGM depressing the small button underneath The MSG SENT LED should momentarily light on the Transmitter and the Receiver will send the following message to the PC Transmitter Learned The association is now complete To disable Transmitter association send the command A 0 lt ENTER gt from the PC to the Receiver The Receiver will indicate that Transmitter association is now disabled MSG LOW SENT BAT dii OK LONG FAIL PGM ID OUR XBEE SECTION 4 OPERATION To send a position message from the ProScale DRO to the ProRF Receiver press the S
6. ansmitter is designed to operate with any ProScale general purpose surface mount LCD Digital Readout DRO that has a built in SPC data port To install the SPC Transmitter complete the following 1 Peel off the backing of the pressure sensitive double faced tape located on the side of the Transmitter housing 2 Plug the 10 pin header from the SPC Transmitter into the side of the ProScale DRO s SPC data port Be sure that all of the pins are properly aligned 3 Press the Transmitter enclosure securely against the DRO housing to ensure that the double faced tape contacts both units adequately ProRF SPC Transmitter User Manual Page 10 of 16 SECTION 3 ASSOCIATION Each ProRF SPC Transmitter is assigned a unique 64 bit ID that identifies that Transmitter to a Receiver For proper communication to occur between the Transmitter and Receiver each Transmitter in the system must be associated or learned by the Receiver The association process is a one time operation where the Receiver is placed into a special mode which listens for new Transmitters to be acquired To learn a particular Transmitter the user then activates a learn pushbutton on the desired Transmitter The Transmitter sends its unique 64 bit ID which the Receiver then stores in its permanent memory Following this operation the Receiver will accept messages from any learned Transmitter and reject messages from unknown Transmitters If you purchased this SPC
7. peer Va S od 14 SECTION 1 GENERAL INFORMATION Introduction Thank you for purchasing the ProRF SPC Transmitter This radio Transmitter unit is designed to be used in conjunction with Accurate Technology Inc ProScale linear measuring systems and the Accurate Technology Inc ProRF Receiver The purpose of this system is to provide a two way wireless communication channel between any ProScale measuring system with a 10 pin SPC output and a computer or other computing device 10 pin SPC output The following is a list of features for the ProRF SPC Transmitter 2 4 GHz radio transceiver providing two way RF communications using the industry standard 802 15 4 communications protocol e 2 LEDs provide RF message status and low battery reporting e Operates from single lithium coin cell battery e 6 months battery lifetime depending on usage e Sixteen selectable RF channels for interference free operation Typical RF signal range 50 to 100 depending on the environment e Small compact enclosure designed to plug into ProScale Digital Readouts DROs that are equipped with an SPC data port Arriirata Tanhnnlnnv Inn Dana Accurate Inc 5 Ol 16 What This Manual Contains This manual includes information on the ProRF SPC Transmitter only The ProRF SPC Transmitter is designed to operate with any ProScale General Pur
8. pment WARRANT Y Accurate Technology Inc warrants this product against defective parts and workmanship for 1 year commencing from the date of original purchase Upon notification of a defect Accurate Technology Inc shall have the option to repair or replace any defective part Such services shall be the customer s sole and exclusive remedy Expenses incidental to repair maintenance or replacement under warranty including those for labor and material shall be borne by Accurate Technology Inc Including freight or transportation charges during the first 30 days Except as expressly provided in this warranty Accurate Technology Inc does not make any warranties with respect to the product either expressed or implied including implied warranties of merchantability or fitness for a particular purpose except as expressly provided in this agreement Accurate Technology Inc shall not be liable for any special incidental or consequential damages or for loss damage or expense directly or indirectly arising from the customer s use of or inability to use the equipment either separately or in combination with other equipment or for personal injury or loss or destruction of other property or from any other cause To request repair work either warranty qualified parts or not contact Accurate Technology Inc directly by phone fax or e mail A Returned Merchandise Authorization RMA number is required before retu
9. pose surface mount LCD Digital Readout DRO that is built with an SPC data port The companion ProRF Receiver is reviewed in a separate user manual ProRF Heceiver Part Number 700 1038 001 For operation and other information on related products please refer to the manuals for those products Terminology This section provides a brief description of terms used within this manual DRO Refers to a ProScale Digital Readout Association Learning Associates one or more Transmitters with the ProRF Receiver to allow position messages to be received TigerStop An automated saw stop fence system that can interface with the ProRF Receiver to automatically build cut list based measurements from a ProScale or ProPanel Measuring System ProRF SPC Transmitter User Manual Page 6 of 16 SECTION 2 INSTALLATION Setting the RF Channel The ProRF SPC Transmitter can be configured to operate on 1 of 16 possible radio frequency channels The default channel is 0 Unless there are other ProRF systems in range that could cause a conflict the default channel setting of 0 should be used Note If the Transmitter s RF channel is changed from its default setting the Receiver s RF channel must also be changed To change the channel complete the following steps If the default channel is to be used skip to Connecting the Transmitter page 10 1 Using a Phillips screwdriver remove the two screws from the back of the housing
10. ress Address City State Region Zip Postal Code Country Purchased From Purchased When Serial Number Thank you for choosing Accurate Technology Product n MADE IN USA Accurate Technology Inc 270 Rutledge Rd Unit E Fletcher NC 28732 USA 800 233 0580 e 828 654 7920 Fax 828 654 8824 www proscale com customerservice accurate technology com This manual is available at www proscale com Please return your Product Registration Card or register your system at www proscale com registration htm P N 800 1342 001 Revision A Copyright 2007 Accurate Technology Inc All rights reserved ProRF SPC Transmitter User Manual Page 16 of 16
11. rning a product for repair This document is protected by the copyright laws of the United States of America No part of this document may be reproduced by any means electronic or otherwise without the expressed written permission of Accurate Technology Inc 1 828 654 7920 800 233 0580 828 654 8824 F www proscale com info accurate technology com Copyright 2004 2007 Accurate Technology Inc All rights reserved P N 800 1342 001 Revision A Firmware Version 1 000 Table of Contents FCC NOTICE 5 2 WARRANTY 3 SECTION 1 GENERAL 2 5 INTRODUCTION Rm 5 WHAT THIS MANUAL CONTAINS 1 42 6 TERMINOLOGY 2 0 cat ede 6 SECTION 2 INSTALLATION iiccisceux es anc era dx oa duce ad pU va rear anu 7 SETTING THE RF CHANNEL 0 nenne nnn nsn 7 RF Channel DIP Switch Settings 9 CONNECTING 1 1 10 SECTION 3 ASSOCIATION 2 122 2 11 ASSOCIATING TRANSMITTERS amp RECEIVERS 2 12 SECTION 4 OPERATION e 13 BATTERY eu tee
Download Pdf Manuals
Related Search