User Manual - Box Design by Pro
Contents
1. 10 DCI BY PRO JECT AUDIO SYSTEMS INSTRUCTIONS FOR USE Pro Ject Tuner Box S Dear music lover thank you for purchasing a Pro Ject Audio Systems FM tuner In order to achieve maximum performance and reliability you should study these instructions for use carefully V Warning of a hazard for the user the unit or possible misuse 15 Important notice Connectors Power Left Right v O In A gt O CO Trigger x Ou SN Pro Ject Audio Systems Vienna Austria Make all connections whilst the tuner is disconnected from the power supply V Take care to connect the left and right channels correctly The right channel is usually marked red the left channel black or white Never use any other power supply than the one supplied with the unit Connection to an amplifier When the Tuner Box S is used with a Pro Ject amplifier connect the line level output to input 1 In 1 on the amp When used with another manufacturers amplifier connect the line level output to the input marked Tuner on the amp Antenna input Connects to any antenna cable with a co axial DIN plug US model F plug Remote switch on The pre amplifier Pro Ject Pre Box S provides a trigger signal to switch on and off the Tuner Box S remotely and for operating the input expander Pro Ject Switch Box S The switching lead should be connected to the Trigger Switch socket on Pre Box S and the Trigger In socket on the Tuner Box S In order to ensur2. tuning mode OK Pressing min 3 seconds ox selects the tuning modes manual program search MANUAL automatic program search AUTO and program selection from memory MEMORY in turns Manual program search the display shows MANUAL as TUNE decreases increases the reception frequency in 50kHz steps Automatic program search the display shows AUTO starts the automatic frequency scan downwards omo starts the scan upwards Program selection from memory the display shows MEMORY O activate the memory function Pressing m O access the presets 1 8 directly and omo select memory function has to be activated the memory positions 9 99 E Saving a program in the memory list Tune to the frequency to be stored Press twice in rapid succession The display will show STORE will select the next memory position up the list om selects the next memory position down the list The memory positions 1 8 can be selected directly by pressing m OK Press once again to store the program at thot position The display shows STORED Saving a program to a particular memory position overwrites any program already stored at that position The memory retains its contents through a power off on cycle and a power failure Pro Ject Audio Systems Pro Ject Tuner Box S Revision 2015 11 04 3 Auto store function Long press starts m confirms the auto store function clears the complete memory wh
3. MORY in the display Saving a program in the memory list The memory of the Pro Ject Tuner Box S can store up to 99 programs Tune to the frequency of the program to be stored Press twice in rapid succession The display will show STORE selects the next memory position up the list lt selects the next memory position down the list Press once on to store the program at that position The display shows STORED To be able to select a tuning mode manual program search automatic program search or 5 program selection from memory a antenna has to be conneced Saving a program to a particular memory position overwrites any program already stored at that position The memory retains its contents through a power off on cycle Replacing batteries Proceed as follows e Unlock and slide open the battery case cover e Replace the battery Make sure the battery is the right way round e Close the battery case cover Battery type 1 x CR2032 3V or 1 x CR2025 3V Do not dispose the batteries as ordinary domestic refuse Please dispose your exhausted batteries at the appropriate collection sites usually located at supermarkets and drugstores Pro Ject Audio Systems Pro Ject Tuner Box S Revision 2015 11 04 5 Technical specifications Pro Ject Tuner Box S Tuning range FM band Programmable presets Frequency response S N ratio THD Stereo separation Sensitivity Antenna input Line level output Trigger Trigger in an
4. d out Output voltage Outboard power supply Power consumption 87 5 108MHz 50kHz steps 99 20Hz 20kHz 1dB 50dB 0 05 At 75kHz and f mod 1kHz 30dB Af 75kHz and f mod 1kHz 7dB uV mono 17dB uV stereo 75 ohms 1 x co axial DIN socket 75 ohms US model F socket 1 pair RCA phono sockets digital switching signal 2 pole co axial 2 5mm co axial jack 0 775Vrms 9V 300mA AC suitable for your country s mains supply 70mA DC lt 1W in standby Dimensions W x H x D D with sockets 103 x 36 x 104 115 mm Weight 565g without power supply Service Should you encounter a problem which you are not able to alleviate or identify please contact your dealer for further advice Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions 15 for use Modification or change to any part of the product by unauthorized persons release the manufacturer from any liability over and above the lawful rights of the customer Safety instructions AC outlet voltages vary from country to country Before connecting to the mains make sure that the voltage in your area meets the voltage requirements printed on the power supply The power supply is used to disconnect the unit from the mains Make sure that the power supply is easily accessible at all times Never hand
5. e correct remote switching the Tuner Box S must be connected to the line level input socket In 1 on the Pro Ject Pre Box S The trigger signal is passed through the Trigger In socket to the Trigger Out socket of the Tuner Box S through which it can be relayed to the input expander Pro Ject Switch Box S Two approx 45cm long trigger leads are supplied with the Pro Ject Tuner Box S Longer leads may be purchased from your Pro Ject dealer Do not use this trigger output for any other connections for which it is not designed If any other input is used to connect the Pro Ject Tuner Box S to a Pro Ject Pre Box S the trigger lead should not be used V Switch off all units and disconnect them from the mains before connecting or disconnecting the trigger lead Failing to do so could result in damage to the units Mains power connection The unit is supplied with a power supply suitable for your country s mains supply Check the label before connecting to ensure compliance with the mains rating in your house Connect the low voltage plug from the power supply to the Power 9V Y socket before connecting the power supply to the mains 2 Pro Ject Audio Systems Pro Ject Tuner Box S Revision 2015 11 04 Remote control Stand By ON OFF short press turns the unit on long press takes it back into standby Powered on a short press activates and deactivates mute Volume vor fois and adjust the sound volume INPUT no function Selecting the
6. ile storing keeps stations with good signal strength in the memory and overwrites stations with insufficient signal level while storing Front panel controls OA O y e Tuner Box S To switch on from standby or to standby The push button on the left hand side will toggle the tuner between its fully operational status and standby The blue LED above the stand by push button shows that the unit is switched on The display shows STANDBY when the unit is in standby If the Tuner Box S is connected to the remote switch on facility of a Pro Ject pre amplitier Pre Box S then choosing input 1 at the pre amplifier will switch the tuner on Selecting a different input will switch the tuner off Dimming the display setting the colour of the display Press approx 5 seconds on the front panel to enter the set up menu of DIM mode Normal operation is not possible when the unit is in DIM mode as a E E i TUNE You can adjust the display brightness by pressing and on the remote control The following settings are available display off DIM 1 DIM 4 and DIM MAX The chosen level will be displayed Additionally the colour ratio settings can be modified dec eases Increases g ee L dec eases m increases blue The changes will be shown in the first line of the display After leaving the set op menu the changes will become valid for the complete display m loads the factory settings for brightness a
7. le the device the power supply while your hands are wet or damp V Avoid letting liquids enter the device or the power supply Never place any item containing liquid such as a flower vase on or near the device Never spill any liquid on the device or the power supply Never place any naked flame sources such as lighted candles on or near the device The product shall not be used in damp or wet locations next to a bathtub sink swimming pool or any other similar conditions Copyright Pro Ject Audio Systems is a Registered Trademark of The information was correct at the time of going to H Lichtenegger press The manufacturer reserves the right to make This guide was produced by Pro Ject Audio Systems changes to the technical specification without prior Copyright 2015 All rights reserved notice as deemed necessary to uphold the ongoing process of technical development 6 Pro Ject Audio Systems gt Pro Ject Tuner Box S Revision 2015 11 04
8. nd colour Confirm your settings by pressing on the remote control to exit the DIM mode To re enter the set up menu of DIM mode press approx 5 seconds on the front panel 4 O Pro Ject Audio Systems gt Pro Ject Tuner Box S Revision 2015 11 04 A Signal strength meter B Stereo reception F Mono reception MED C Fine tuning meter D Tuning mode toggles between the tuning modes E Tuned frequency Manual program search Press approx 3 seconds repeatedly until the display shows MANUAL gt increases the reception frequency in 50kHz steps 4 decreases the reception frequency in 50kHz steps The tuner is correctly adjusted for a stereo broadcast when A the largest number of bars are shown signal strength meter and B two loudspeaker symbols are shown F one loudspeaker symbol shows mono reception C the vertical bar is centred in the fine tuning display Automatic program search Press approx 3 seconds repeatedly until the display shows AUTO gt starts the automatic frequency scan upwards will start it downwards The maximum signal strength will be adjusted automatically for each program found Program selection from memory Press approx 3 seconds repeatedly until the display shows MEMORY b will select the program with the next memory position up the list lt selects the program with the next memory position down the list The program s memory position is shown to the right of ME
Download Pdf Manuals
Related Search