VR2W Quick Guide
Contents
1. ts v VemMmMCco VR2W Quick Guide This VR2W Quick Guide provides information on key VR2W procedures Full details for all VR2W procedures are found nA a secant in the VR2W User manual and at www vemco com We extreme temperature variations strongly recommend you study the full user manual before Doing so may damage the receiver and render using this quick guide it unable to detect transmitters Open Case Place VR2W on clean stable surface so hydrophone hangs off edge We recommend working in a controlled environment Insert one steel rod into the Attachment hole and other one in the Comm Key Hole on the end cap and hold on to the rods Apply pressure to the rod in the COMM Key hole to turn end cap counter clockwise when you are facing the hydrophone Remove rod when end cap turns easily and continue turning by hand Electronics inside the case Slide end cap and cylinder apart until the battery must NEVER come in compartment has cleared the cylinder Be very contact with any water or careful not to damage the threads on the end cap the VR2W will be damaged or the VR2W won t close and seal properly Battery The battery is held in the battery compartment by a plastic pin spanning the opening Remove the thin O ring before removing the pin O ring holds pin in place Downward force on battery may be needed to allow pin to move The battery is connected to VR2W on the side of the ca2. eiver information seconds VR2W Status Light is continuously on Remove the Comm key during communication Having trouble Try a new battery Actions such as starting a study offloading data and ending communication are performed from the Receiver Tab and are started by selecting the correct icon in the tab s ribbon Details are found in the VR2W user manual WR2W 105604 VUE Actions Close View ends communication with VR2W and closes receiver tab Home QJ VR2W 105684 J VR2W 108482 Start Recording setup and begin a study also erases Receiver resumes recording gt a n VR2W memory does not initialize Attachment The common method used to attach a VR2W receiver to a mooring line is to use five cable ties zip tie or tie wrap with the following characteristics e 388 mm 15 25 long 5 e 7 5 mm 0 3 wide e UV protected e 120 lb tensile strength Open the wrap in the rope to pass the cable tie through the rope Through Rope Around Rope Around Rope Through Rope Avoid shadowing or blocking the receiver with your mooring equipment Line of sight is a must Status Light m x Operating temperature 5 C to 40 C Water in which Flash Meanings the VR2W is deployed must not freeze No flashes no power _ Static depth rating 500 meters 730 psi 2 quick flashes every 5 sec in Recording Mode gt 2 quick flashes every 10 sec memory is full 1 quick flash ac
3. oustic ping received 1 bright long flash detection written to memory mN ww vemco com 1 long flash per sec ready for Bluetooth communication ve MC O On solid communicating with VUE 1 902 450 1700
4. se When installing the battery listen for a click and watch that light flashes four times and then twice quickly every 5 seconds When disconnecting battery press the release tab on the battery connector and then pull connector halves apart TIP Write the date on the battery O rings Close Case Make sure the two O rings in the end cap and the Close the VR2W case by doing the reverse of opening it but corresponding O ring surface inside the Outer first put a new desiccant pack in the bottom of the tube Cylinder are clean and debris free If the VR2W Slide the battery end into the Outer Cylinder Rotate the end has previously cap clockwise using been deployed the steel bars when replace the needed O rings Stop turning when the gap between the two halves is closed Over tightening could damage the case A desiccant pack helps reduce the occurrence of condensation in the VR2W Activate lan Communicate Slide the smaller end of the Open VUE and wait while software a Comm Key in the Comm Key scans for the activated VR2W If it Hole on the VR2W near the doesnt scan then click the Device hydrophone f Scan button ee Wait until the VR2W s LED After VR2W is located double click begins flashing a bright long on the receiver icon with the correct steady flash once a second serial number to open communication The wait time is less than five and display rec
Download Pdf Manuals
Related Search