Hamilton Beach 840065601 User's Manual
Contents
1. when blending Do not put hands spoons or other utensils in jar when blending Failure to follow these instructions can result in broken bones or cuts Requesting Assistance or Service Before calling for assistance or service please check the Troubleshooting Guide in this manual If you still need help follow the instructions below Whenever you call to request assistance or service you need to know the complete model number You can find this information on the label on the bottom of your blender Please also record the purchase date of your equipment and your dealer s name address and telephone number Model Number Purchase Date Dealer Name Dealer Address Dealer Phone You can also order replacement parts by calling your nearest Hamilton Beach Commercial Service Center or your local dealer Call our Technical Service number 866 285 1087 or 910 692 2223 8 a m 5 30 p m EST Monday Thursday 8 a m 5 15 p m EST Friday www commercial hamiltonbeach com Blender Safety IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical appliances basic safety precautions should be followed including the following e Read all instructions e Plug into a grounded outlet e Do not touch surfaces that may be hot Use handles or knobs provided e Extreme caution must be used when moving an appliance containing hot oil or other hot liquids e Do not use appliance f2. ded electrical outlet Place the jar on the base with ingredients and jar lid in place Set the controls to your pisierence Move the power switch to the on or I position except model 915 Move the power switch to start run or position Caring for the Blender Cleaning the Blender AWARNING y Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Cleaning The jar should be cleaned immediately AFTER EACH USE The jar can be cleaned in the following manner 1 Fill the jar half full with warm water 122 degrees F 50 degrees C 2 Add a drop of liquid detergent or 1 2 teaspoon of detergent powder 3 Place the cover filler cap on the jar and blend on C cycle or the High setting for 30 seconds 4 Turn the blender off and then rinse the jar and wipe down to dry Do not disassemble the cutter assembly 5 Wash the jar cover filler cap in warm soapy water Rinse and let dry 6 Unplug the blender 7 Wipe down the blender base with a damp cloth AWARNING Cut Hazard Always place cover on jar when blending Do not put hands spoons or other utensils in jar when blending Failure to follow these instructions can result in broken bones or cuts Sanitizing If the blender will not be used again within 1 hour sanitize the container
3. ender to the nearest authorized service facility for examination repair or electrical or mechanical adjustment Replacement Parts Refer to Requesting Assistance or Service on page 2 to order parts below 32 oz Polycarbonate jar and cutter assembly includes cover filler cap 6126 91515 Product Warranty This Warranty supercedes all other Product Warranties This product is warranted to be free from defects in material and workmanship for a period of three 3 years parts two 2 years labor OR 15 000 cycles whichever comes first from the date of original pur chase except as noted below There is a lifetime warranty on the motor drive coupling and blade During this period we will repair or replace this product at our option at no cost to you THE FOREGOING WARRANTY IS IN LIEU OF ANY OTHER WARRANTY WHETHER EXPRESSED OR IMPLIED WRITTEN OR ORAL INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ANY LIABILITY IS EXPRESSLY LIMITED TO AN AMOUNT EQUAL TO THE PURCHASE PRICE PAID AND ALL CLAIMS FOR SPECIAL INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED There is no warranty with respect to the following which may be supplied with this product motor brushes container and cutter assembly container clutches bristle brushes funnel stainless steel cup agitators carafes etc This warranty extends only to the original purchaser and does not cover a defect resulting from abuse misuse
4. hin rubber spatula to push mixture towards cutters Do not spray the base with a high pressure spray gun Disconnect power before cleaning or servicing To prevent burns from hot liquids splashing out of the jar always remove the filler cap of the container cover before blending hot liquids Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner Return appliance to the nearest service facility for examination repair or electrical or mechanical adjustment If the supply cord of this appliance is damaged it must be replaced by the manufacturer or its service agent or a similar qualified person If fitted with a non rewirable U K plug the 13 amp fuse approved by ASTA to be B S 1362 must be used If you need a replacement fuse carrier it must be replaced by the same colour coded carrier with the same markings Fuse covers and carriers can be obtained from approved service agents IMPORTANT If the molded plug is cut off dispose of it immediately The plug is not rewirable and would cause a shock hazard if inserted into a socket For a complete operation manual in this language please visit our website at www commercial hamiltonbeach com or call 910 692 2223 SAVE THESE INSTRUCTIONS Blender neration luick Start Guide Place the Ul on a dry level surface Make sure the power switch is in the off or O position Plug the blender into a groun
5. in the following manner 1 After washing the jar fill it with a cold chlorine based sanitizing solution that has a minimum chlorine concentration of 100 parts per million See recommended solution below Place the cover filler cap on the jar and blend on C cycle or the High setting for a minimum of 2 minutes Empty the jar but do not rinse Dry the jar by placing it on the blender base and turn the blender on C Slide step cycle or the High setting for 2 seconds Recommended Sanitizing Solution The sanitizing solution should consist of 1 tablespoon of household bleach per 1 gallon of clean cool water 60 F 16 C mixed according to the instructions on the bleach When using a sanitizing solution other than that recommended the sanitizing solution concentration should be tested using commercially available test strips and should indicate a concentration between 100 and 200 parts per million of bleach to water Caring for the Blender Troubleshooting Guide Operation Status light A system fault has been detected Unplug unit for 5 seconds and then plug unit lights red back in If light is still red unplug unit for 6 minutes and then plug unit back in on some models If light is still red refer to Requesting Assistance or Service If Operation Status light repeatedly lights red refer to Requesting Assistance or Service Unit will not run e Check to see if unit is securely plugged into an elect
6. neglect unauthorized repair or any use not in conformity with the printed directions Always use this product in the manner provided in the Operation Manual This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state or province to province Some states do not allow limitations on implied warranties or special incidental or consequential damages so the foregoing limitations may not apply to you If you have a claim under this warranty please contact our TECHNICAL SERVICE CENTER 1 866 285 1087 For faster service please have model series and type numbers ready for the operator to assist you Reasonable proof of the date of purchase must be presented otherwise the effective date of the warranty will be based on the date of manufacture plus ninety days Hamilton Beach Proctor Silex Inc Commercial Customer Service 263 Yadkin Road Southern Pines NC 28387
7. oOo M M E R Cl A L Tempest Series Blenders Operation Manual ee ee ee Melangeurs de series Tempest Manuel d utilisation 5 Licuadoras de series Tempest Manual de uso 840065601 Technical Service 1 866 285 1087 www commercial hamiltonbeach com Blender Safety IMPORTANT This operation manual should be reviewed with all equipment operators as part of your operator training program Your safety and the safety of others is very important We have provided many important safety messages in this manual and on your appliance Always read and obey all safety messages This is the safety alert symbol This symbol alerts you to hazards that can kill or hurt you and others All safety messages will be preceded by the safety alert symbol and the word DANGER or WARNING These words mean You will be killed or seriously injured if VIN oN Ce ER you don t follow instructions You can be killed or seriously injured if AWARN l NG you don t follow instructions All safety messages will identify the hazard tell you how to reduce the chance of injury and tell you what can happen if the instructions are not followed AWARNING AWARNING y Electrical Shock Hazard Plug into a grounded outlet Do not remove ground Do not use an adapter Do not use an extension cord Failure to follow these instructions can result in death fire or electrical shock Cut Hazard Always place cover on jar
8. or other than intended use e To protect against electrical shock do not immerse cord plug or blender base in water or any other liquid e Close supervision is necessary when any appliance is used by or near children e The use of accessory attachments not recom mended by Hamilton Beach may cause injuries e To reduce risk of personal injury unplug cord from outlet when not in use and before putting on or taking off parts or doing any other servicing of the blender e Do not let cord hang over edge of table or counter or touch hot surfaces e Do not place on or near a hot gas or electric burner or in a heated oven e To reduce risk of personal injury and to prevent damage to blender or jar and cutter assembly DO NOT insert utensils into blender jar while operating blender or store utensils in the blender jar when it is not in use e Avoid contacting moving parts e Blades are sharp Handle carefully e Inspect jar and cutter assembly daily Check cutter for wear nicks or broken blades Replace jar and cutter assembly at least every 12 months e Do not defeat the jar pad sensors e Do not use outdoors e This appliance is intended for short periods of operation with a rated operating time of 3 minutes e To prevent damage to blender jar or cutter assembly DO NOT move or shake blender while in operation If blending action stops during operation turn blender OFF remove jar from base remove jar cover and use a t
9. ric outlet e Check to see if operation light is illuminated when blender is On e Check to see if the fuse for the electric outlet has blown or if a circuit breaker has tripped e Jar is not securely seated on the base Ingredients will not mix Check to see if enough liquid has been added to the ingredients Mixture should properly be fluid and free running at all times e Solid pieces are too large Pieces should not exceed 1 cubes e Jar is too full Do not fill past highest graduation marking e Cutters are not sharp or are damaged Inspect jar and cutter assembly daily Replace jar and cutter assembly at least every 12 months or when damaged Operation Status light Jar is not on blender base lights yellow Jar is not securely seated on optional jar pad sensors on some models Maintenance Inspect the blender and its various parts and replace as follows Daily Unplug the blender and remove the jar from the base and then inspect the jar and cutter assembly for wear nicks or broken blades Replace if necessary See Replacement Parts below Weekly Unplug the blender and then inspect the power cord insulation and power plug for cracks Refer to Requesting Assistance or Service for repair or replacement Replace the jar and cutter assembly at least once a year See Replacement Parts below NOTE Do not operate this blender if it malfunctions or is dropped or damaged in any manner Return bl
Download Pdf Manuals
Related Search