User`s manual Flir K series
Contents
1. A CAUTION Applicability Cameras with one or more batteries Only use a specified battery charger when you charge the battery Damage to the battery can occur if you do not do this T559811 r AE 9082 9150 en US Warnings amp Cautions A CAUTION Applicability Cameras with one or more batteries The temperature range through which you can charge the battery is 0 C to 45 C 32 F to 113 F unless other information is specified in the user documentation or technical data If you charge the bat tery at temperatures out of this range it can cause the battery to become hot or to break It can also de crease the performance or the life cycle of the battery N CAUTION Applicability Cameras with one or more batteries The temperature range through which you can remove the electrical power from the battery is 15 C to 50 C 5 F to 122 F unless other information is specified in the user documentation or technical data If you operate the battery out of this temperature range it can decrease the performance or the life cycle of the battery A CAUTION Applicability Cameras with one or more batteries When the battery is worn apply insulation to the terminals with adhesive tape or equivalent materials before you discard it Damage to the battery and injury to persons can occur if you do not do this A CAUTION Applicability Cameras with one or more2. Notice to user 3 1 User to user forums Exchange ideas problems and infrared solutions with fellow thermographers around the world in our user to user forums To go to the forums visit http www infraredtraining com community boards 3 2 Calibration We recommend that you send in the camera for calibration once a year Contact your lo cal sales office for instructions on where to send the camera 3 3 Accuracy For very accurate results we recommend that you wait 5 minutes after you have started the camera before measuring a temperature 3 4 Disposal of electronic waste As with most electronic products this equipment must be disposed of in an environmen tally friendly way and in accordance with existing regulations for electronic waste Please contact your FLIR Systems representative for more details 3 5 Training To read about infrared training visit http Avww infraredtraining com http www irtraining com http www irtraining eu 3 6 Documentation updates Our manuals are updated several times per year and we also issue product critical notifi cations of changes on a regular basis To access the latest manuals and notifications go to the Download tab at http support flir com It only takes a few minutes to register online In the download area you will also find the latest releases of manuals for our other products as well as manuals for our historical and obsolete products 3 7 Importa
3. e USB cable e User documentation CD ROM Note FLIR Systems reserves the right to discontinue models parts or accessories and other items or to change specifications at any time without prior notice 8 2 List of accessories and services 1910423 USB cable Std A to Mini B T127722 Retractable lanyard T127724 Neck strap T198125 Battery charger including power supply with multi plugs T198310 Battery T198322 In truck charger T198416 Lanyard strap T198441 Transport case T198457 Tripod Adapter e T199844 One year extended warranty Note FLIR Systems reserves the right to discontinue models parts or accessories and other items or to change specifications at any time without prior notice 311559811 r AE 9082 9150 en US System parts 9 1 Camera 9 1 1 Figure 1 4 9 1 2 Explanation pen oouxodm USB Mini B connector Connect to a computer to download images using Flir Tools Attachment point for lanyard strap neck strap left and right side Eccentric latch to secure the battery On off button This button has two functions e Push and holdto turn on off Push to go to default mode Mode button Push repeatedly to select camera modes Access to setup menus and stored images Push Mode Zoom button Zoom button zoom factor 2x Connectors for in truck charger Save trigger
4. 10 Mount for tripod adapter 11 Attachment point for retractable lanyard 12 Battery 11559811 r AE 9082 9150 en US 11 System parts 9 2 Lanyard strap retractable lanyard 9 2 1 Figure 9 2 2 Explanation The lanyard strap is attached at position 2 on the camera see section 9 1 Camera page 11 The retractable lanyard is then connected to the lanyard strap 9 3 Neck strap 9 3 1 Figure 9 3 2 Explanation The neck strap is attached at position 2 on the camera see section 9 1 Camera page 11 11559811 r AE 9082 9150 en US 12 10 Screen elements 10 1 Figure 10 2 Explanation 1 Heat detection mode Optimized for searching hotspots during overhaul after the fire is out 2 Search and rescue mode Optimized for maintaining high contrast in the infrared im age while searching for people 3 Fire mode Similar to the NFPA firefighting mode but with a higher temperature start ing point for the heat colorization 4 Black and white firefighting mode Multipurpose mode for the initial fire attack with life rescuing operation and control of the fire 5 NFPA firefighting mode Multipurpose mode for the initial fire attack with life rescuing operation and control of the fire 6 Overheating indicator The indicator provides a visual warning to the user that the thermal imager is about to shut down due to internal overheating 7 Temperature scale 8 Spotmeter 9 Battery condition
5. The camera model The camera serial number The communication protocol or method between the camera and your device for ex ample HDMI Ethernet USB or FireWire Device type PC Mac iPhone iPad Android device etc Version of any programs from Flir Systems Full name publication number and revision number of the manual 4 3 Downloads On the customer help site you can also download the following Firmware updates for your infrared camera Program updates for your PC Mac software Freeware and evaluation versions of PC Mac software User documentation for current obsolete and historical products e Mechanical drawings in dxf and pdf format Cad data models in stp format Application stories Technical datasheets Product catalogs 11559811 r AE 9082 9150 en US 6 Important information about Flir K series service e Contact the service department before shipping the camera Many problems can be resolved on the phone if so the camera does not need to be shipped The camera must be thoroughly cleaned and decontaminated before shipping No hazardous residues are allowed on cameras shipped to our service department Such residues include but are not limited to chemical fire extinguishing compounds ra dioactivity biohazardous materials and residues from chemical fires Flir Systems reserves the right to charge the full cost for the decontamination of con taminated
6. infrared imaging systems and is the world leader in the design manufacture and mar keting of thermal imaging systems for a wide variety of commercial industrial and gov ernment applications Today Flir Systems embraces five major companies with outstanding achievements in infrared technology since 1958 the Swedish AGEMA In frared Systems formerly AGA Infrared Systems the three United States companies In digo Systems FSI and Inframetrics and the French company Cedip In November 2007 Extech Instruments was acquired by Flir Systems PATENT SPEC N n ae United States Patent Office 3 253 408 Tere PER JONAN LINDEIRO ani MANS GUNNER Patented May 31 1906 1 2 lem bs sur a rem ps 9 sis d casona sec RASS roa rca Dn To A ma i alg e MR K EMER a Set rhe VETUS tend Nn pn om LT pain pom lies m cc HM IUE LIU y li i i 1 i H Hi j 1 i l H I i j f He T E SH id liri in I ji 1 i i pi s stilt E t n f h jp k i E 1 l li ui i i i H ill n lli tH a il i F q ut H 1 b I il T elf Li il 1 35 i i KR i li T i hi Hh f TN jg L int H Rei i ii HL x l T 1 f r He li t i I i if H fi p H i H 2 il Hu il n L 1 n ik i T d N j i y it i Hi i E L H ij Ber 1 i i I hi HE 7 D I
7. Protection Association an internation al non profit organization See www nfpa org for more details Black and white firefighting mode Fire mode Search and rescue mode Heat detection mode H RON Each mode is optimized for a certain type of firefighting application In addition the modes differ in the following way Modes with green icons 1 3 below The camera switches between the high sensitiv ity range 20 to 150 C 4 to 302 F and the low sensitivity range 0 to 650 C 32 to 1202 F automatically when objects with a temperature above 150 C 302 F enters the field of view of the camera Modes with blue icons 4 5 below The temperature range is locked to the high sen sitivity range 20 to 150 C 4 to 302 F This is useful if you need to maintain the best possible image for objects with a temperature below 150 C 3029F even if there are objects with a temperature above 150 C 302 F in the field of view of the camera 11 3 2 Explanation of the different camera modes 11 3 2 1 NFPA firefighting mode Figure 11 1 NFPA firefighting mode The NFPA standardized firefighting mode is the default mode of the camera It is a multi purpose mode for the initial fire attack with life rescuing operation and control of the fire The camera automatically switches between the high sensitivity range and the low sen sitivity range to maintain an optimal infrared image while at the same time maintaining
8. Push and hold the Mode button then push the Zoom button This will display the screen below FLIR Exit X Archive Settings 2 Select Settings by pushing the Zoom button This will display the screen below Temperature unit Next gt Adjust 3 Select Next by pushing the Mode button to navigate to the parameter that you want to change 4 Select Adjust by pushing the Zoom button to change the value 5 Select Exit by pushing the On off button to confirm the choice and exit the dialog box 11559811 r AE 9082 9150 en US 22 12 In truck charger optional accessory 12 1 Introduction Thank you for choosing the Flir K series in truck charger from Flir Systems The in truck charger is intended to be mounted on a flat surface in the cab in one of the equipment lockers or in another suitable compartment on the fire engine The in truck charger has five ports for cable routing one through the rear of the metal bracket and one port on each side of the in truck charger The in truck charger can also be powered using a standard Flir Systems power supply and has a battery charger located at the lower front of the unit 12 2 Parts and functions 1 Top cover 2 LED indicator for the ca
9. batteries Remove any water or moisture on the battery before you install it Damage to the battery can occur if you do not do this A CAUTION Do not apply solvents or equivalent liquids to the camera the cables or other items Damage to the bat tery and injury to persons can occur A CAUTION Be careful when you clean the infrared lens The lens has an anti reflective coating which is easily dam aged Damage to the infrared lens can occur A CAUTION Do not use too much force to clean the infrared lens This can cause damage to the anti reflective coating Note The encapsulation rating is only applicable when all the openings on the camera are sealed with their correct covers hatches or caps This includes the compartments for data storage batteries and connectors A CAUTION Do not change the standard fire fighting procedures when you use a Flir K series camera The Flir K series camera is not a replacement technology A CAUTION Do not use the Flir K series camera without the correct training If the persons that operate the camera do not have the correct training an incorrect analysis of the infrared images can occur Thus incorrect decisions during the firefighting can be made The training must include Howathermal camera operates and its limits e How to interpret an image Howto work safely with the camera 11559811 r AE 9082 9150 en US
10. founded the Infrared Training Center ITC a separate business unit that provides certi fied training courses Attending one of the ITC courses will give you a truly hands on learning experience The staff of the ITC are also there to provide you with any application support you may need in putting infrared theory into practice 15 3 Supporting our customers Flir Systems operates a worldwide service network to keep your camera running at all times If you discover a problem with your camera local service centers have all the equipment and expertise to solve it within the shortest possible time Therefore there is no need to send your camera to the other side of the world or to talk to someone who does not speak your language 11559811 r AE 9082 9150 en US 29 15 About Flir Systems 15 4 Afew images from our facilities Figure 15 5 LEFT Testing of infrared cameras in the climatic chamber RIGHT Robot used for camera testing and calibration 111559811 r AE 9082 9150 en US 30 16 History of infrared technology Before the year 1800 the existence of the infrared portion of the electromagnetic spec trum wasn t even suspected The original significance of the infrared spectrum or simply the infrared as it is often called as a form of heat radiation is perhaps less obvious to day than it was at the time of its discovery by Herschel in 1800 Figure 16 1 Sir William Herschel 1738 1822 The di
11. in the connector bay 6 Do one of the following Move the images to the computer using a drag and drop operation Note Moving an image using a drag and drop operation does not delete the image in the camera Move the images to the computer using Flir Tools 11559811 r AE 9082 9150 en US 20 11 Operation 11 6 Viewing saved images 11 6 1 General When you save an image the image is stored in the camera s image archive To display the image again you can recall it from the archive 11 6 2 Procedure Follow this procedure 1 2 3 4 Push and hold the Mode button then push the Zoom button This will display the screen below FLIR Exit X Archive 2 Settings Select Archive by pushing the Mode button This will display the screen below 14 38 23 12 10 23 IMG 123 Next gt Maximize 53 In the image archive do one of the following Select Next by pushing the Mode button to navigate in the image archive Select Maximize by pushing the Zoom button to enlarge a specific image Select Exit by pushing the On off button to exit the image archive 11559811 r AE 9082 9150 en US 21 11 Operation 11 7 Changing settings 11 7 1 General You can change a variety of settings These settings include the following Temperature unit Temperature indication Date Time Factory default settings 11 7 2 Procedure Follow this procedure 1
12. may be reproduced transmitted transcribed or translated into any language or computer language in any form or by any means electronic magnetic optical manual or otherwise without the prior written permission of FLIR Systems The documentation must not in whole or part be copied photocopied re produced translated or transmitted to any electronic medium or machine readable form without prior consent in writing from FLIR Systems Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems and or its subsidiaries All other trademarks trade names or company names referenced herein are used for identification only and are the property of their respective owners 1 6 Quality assurance The Quality Management System under which these products are developed and manufactured has been certified in accordance with the ISO 9001 standard FLIR Systems is committed to a policy of continuous development therefore we reserve the right to make changes and improvements on any of the prod ucts without prior notice 1 7 Patents One or several of the following patents and or design patents may apply to the products and or features Additional pending patents and or pending de sign patents may also apply 000279476 0001 000439161 000499579 0001 000653423 000726344 000859020 001 106306 0001 001707738 001707746 001707787 001776519 001954074 002021543 002058180 001 1144833 11
13. while at the same time maintaining a safe and consistent colorization of heat Automatic range e Colorization of heat 250 to 650 C 482 to 1202 F High sensitivity range 20 to 150 C 4 to 302 F e Low sensitivity range 0 to 650 C 32 to 1202 F 11559811 r AE 9082 9150 en US 16 11 Operation 11 3 2 4 Search and rescue mode Figure 11 4 Search and rescue mode The search and rescue mode is optimized for maintaining high contrast in the infrared image while searching for people in landscapes buildings or traffic accident scenes High sensitivity range only e Colorization of heat 100 to 150 C 4212 to 302 F e High sensitivity range 20 to 150 C 4 to 302 F 11 3 2 5 Heat detection mode Figure 11 5 Heat detection mode The heat detection mode is optimized for searching hotspots during overhaul after the fire is out typically to ensure that there is no hidden fire left This mode can also be used to find thermal patterns for example signs of people in car seats after accidents to ensure that everyone has been found This mode can also be used to search for people in water and open landscapes High sensitivity range only e Colorization of heat the 20 hottest area in the scene High sensitivity range 20 to 150 C 4 to 302 F 11559811 r AE 9082 9150 en US 17 11 Operation 11 4 Saving an image 11 4 1 General You can save imag
14. 1 2013 04 04 T505469 xml en US 8097 2013 06 11 T505013 xml en US 8097 2013 06 11 T505508 xml en US 6607 2013 02 26 T505509 xml en US 6607 2013 02 26 T505510 xml en US 6343 2013 01 25 T505511 xml en US 6564 2013 02 22 T505512 xml en US 8262 2013 06 26 T505514 xml en US 8904 2013 09 10 T505516 xml en US 6342 2013 01 25 T505097 xml en US 5929 2012 10 29 T505470 xml en US 5935 2012 10 29 T505007 xml en US 6351 2013 01 28 T505005 xml en US 5939 2012 10 29 11559811 r AE 9082 9150 en US FLIR For more information contact Corporate Headquarters FLIR Systems Inc 27700 SW Parkway Ave Wilsonville OR 97070 USA TEAM EQUIPMENT INC zaa 1 509 498 3547 TIME TESTED TIME TRUSTED SINCE 1985 ebsite hito Me G 6620 Orchid Lake Rd New Port Richey FL 34655 1111 727 848 2424 800 367 9054 fax 727 845 5941 Customer support A pp www teameguipment com www teamrescuestore com http support flir com Publ No 1559811 Release AE Commit 9082 Head 9150 Language en US Modified 2013 09 23 Formatted 2013 09 26
15. 6 US gallon jar with liquid nitrogen To the left of the oscilloscope the Polaroid attachment 6 kg 13 Ib can be seen RIGHT Flir i7 from 2012 Weight 0 34 kg 0 75 Ib including the battery Flir Systems manufactures all vital mechanical and electronic components of the camera Systems itself From detector design and manufacturing to lenses and system elec tronics to final testing and calibration all production steps are carried out and super vised by our own engineers The in depth expertise of these infrared specialists ensures the accuracy and reliability of all vital components that are assembled into your infrared camera 15 1 More than just an infrared camera At Flir Systems we recognize that our job is to go beyond just producing the best infrared camera systems We are committed to enabling all users of our infrared camera systems to work more productively by providing them with the most powerful camera software combination Especially tailored software for predictive maintenance R amp D and process monitoring is developed in house Most software is available in a wide variety of languages We support all our infrared cameras with a wide variety of accessories to adapt your equipment to the most demanding infrared applications 15 2 Sharing our knowledge Although our cameras are designed to be very user friendly there is a lot more to ther mography than just knowing how to handle a camera Therefore Flir Systems has
16. 82246 1182620 1285345 1299699 1325808 1336775 1391114 1402918 1404291 1411581 1415075 1421497 1458284 1678485 1732314 2106017 2381417 3006596 3006597 466540 483782 484155 4889913 5177595 60122153 2 60200401 1681 5 08 6707044 68657 7034300 7110035 7154093 7157705 7237946 7312822 7332716 7336823 7544944 7667198 7809258 7826736 8 018 649 B2 8 153 971 8212210 B2 8289372 8354639 B2 8384783 D540838 D549758 D579475 D584755 D599 392 D615 113 D664 580 D664 581 D665 004 D665 440 DI6702302 9 DI6903617 9 DI7002221 6 DI7002891 5 DI7002892 3 DI7005799 0 DM 057692 DM 061609 EP 2115696 B1 EP2315433 SE 0700240 5 US 8340414 B2 ZL01823221 3 ZL01823226 4 ZL02331553 9 ZL02331554 7 ZL200480034894 0 ZL200530120994 2 ZL200610088759 5 ZL200630130114 4 ZL200730151141 4 ZL200730339504 7 ZL200820105768 8 ZL200830128581 2 ZL200880105236 4 ZL200880105769 2 ZL200930190061 9 ZL201030176127 1 ZL201030176130 3 ZL201030176157 2 ZL201030595931 3 ZL201130442354 9 ZL201230471744 3 ZL201230620731 8 1 8 EULATerms e You have acquired a device INFRARED CAMERA that includes soft ware licensed by Flir Systems AB from Microsoft Licensing GP or its af filiates MS Those installed software products of MS origin as well as associated media printed materials and online or electronic docu mentation SOFTWARE are protected by international intellectual property laws and treaties The
17. FLIR User s manual Flir K series FLIR User s manual Flir K series N TERE a AmA Dc 311559811 r AE 9082 9150 en US Table of contents o AI O Gi 10 11 Legal 01SeGlaimer zc vs zx sezv reger st esc ygy gx Sos yx RZ e SSK nennen nnne anna nsan 1 1 1 Legal disclaimer 1 1 2 Usage statistics aaa mi elek lek alarak ella Skal Yeli 1 1 3 Changes to registry oi ilan ac ee dinar eae 1 1 4 U S GovernmentRegulations 1 1 5 Gopytiglit cL o kiza ekl elele ebabil el beee RET EUR 1 1 6 Quality assurances 4 1 Erde cl eese ye Mya MU ode RL d 1 1 7 Pa seneki Em 1 1 8 EULA TERMS un a amaa A 1 Warninggs amp Cautions ee eee enen eee aaa 2 Notice TOUSEN suresi sarun varsin dren reaz ir A dN HRK KD BEM sees vR r 5 3 1 User to ser fOrUMS tits 5 3 2 Calibration o aa ot Silan leke e Meme le See le 5 3 3 ACGUIACY 3i rd samim RM RR RPM ERR IR ERR anlak le 5 3 4 Disposalofelectronicwaste 5 3 5 O babi sile 5 3 6 Documentation Updates ses ee ee e eee K 5 3 7 Importantnoteaboutthismanual 5 Customer help 12315111 IE ire ePi ities 6 4 1 General ee eur e eer MEI MINI I Rise e 6 4 2 Submittingaguestion 6 4 3 Downloads i i eR IR ENS MAREC uha isis 6 Important information abou
18. Flir K series can be controlled by just three large buttons on top of the unit and one trigger Ideal for a gloved firefighter s hand Produce simple reports in Flir Tools Thermal images can be stored in the Flir K series and later used to produce simple reports of what happened at the scene 11559811 r AE 9082 9150 en US 8 Quick start guide Follow this procedure to get started right away 1 Charge the battery for 4 hours before starting the camera for the first time or until the blue battery condition LED glows continuously Push the On off button to turn on the camera Aim the camera toward the object of interest Select a suitable camera mode by pushing the Mode button Pull the Save trigger to save an image Connect the camera to a computer using the USB cable Do one of the following NoonsoQm Move the image to the computer using a drag and drop operation Note Moving an image using a drag and drop operation does not delete the image in the camera Move the image to the computer using Flir Tools A download card for Flir Tools is included in the transport case In Flir Tools you can analyze the images and create PDF reports 11559811 r AE 9082 9150 en US 9 Parts lists 8 1 Scope of delivery Infrared camera Battery 2 Battery charger Hardtransport case Lanyard strap e Neck strap Power supply Printed documentation Retractable lanyard Tripod adapter
19. OR IN CONNECTION WITH THE USE OR PER FORMANCE OF THE SOFTWARE THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PUR POSE IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U S TWO HUNDRED FIFTY DOL LARS U S 250 00 Limitations on Reverse Engineering Decompilation and Dis assembly You may not reverse engineer decompile or disas semble the SOFTWARE except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation SOFTWARE TRANSFER ALLOWED BUT WITH RESTRIC TIONS You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device and only if the recipient agrees to this EULA If the SOFTWARE is an up grade any transfer must also include all prior versions of the SOFTWARE EXPORT RESTRICTIONS You acknowledge that SOFTWARE is subject to U S export jurisdiction You agree to comply with all ap plicable international and national laws that apply to the SOFT WARE including the U S Export Administration Regulations as well as end user end use and destination restrictions issued by U S and other governments For additional information see http www microsoft com exporting 11559811 r AE 9082 9150 en US Warnings Cautions A WARNING Applicability Cameras with one or more batteries Do not disassemble or do a modification to the battery The battery contains safet
20. SOFTWARE is licensed not sold All rights reserved IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT EULA DO NOT USE THE DEVICE OR COPY THE SOFTWARE IN STEAD PROMPTLY CONTACT Flir Systems AB FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE S FOR A REFUND ANY USE OF THE SOFTWARE INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA OR RATIFICATION OF ANY PREVIOUS CONSENT GRANT OF SOFTWARE LICENSE This EULA grants you the following license You may use the SOFTWARE only on the DEVICE NOT FAULT TOLERANT THE SOFTWARE IS NOT FAULT TOL ERANT Flir Systems AB HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE AND MS HAS RELIED UPON Flir Systems AB TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE NO WARRANTIES FOR THE SOFTWARE THE SOFTWARE is provided AS IS and with all faults THE ENTIRE RISK AS TO SATISFACTORY QUALITY PERFORMANCE ACCURACY AND EFFORT INCLUDING LACK OF NEGLIGENCE IS WITH YOU ALSO THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE THOSE WAR RANTIES DO NOT ORIGINATE FROM AND ARE NOT BINDING ON MS No Liability for Certain Damages EXCEPT AS PROHIBITED BY LAW MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM
21. a safe and consistent heat colorization of the fire scene Automatic range e Colorization of heat 150 to 650 C 302 to 1202 F e High sensitivity range 20 to 150 C 4 to 302 F e Low sensitivity range 0 to 650 C 32 to 1202 F 11559811 r AE 9082 9150 en US 15 11 Operation 11 3 2 2 Black and white firefighting mode Figure 11 2 Black and white firefighting mode The black and white firefighting mode is an NFPA standardized firefighting mode It is a multipurpose mode for the initial fire attack with life rescuing operation and control of the fire Itis specifically designed for fire services that do not want to use the heat coloriza tion feature The camera automatically switches between the high sensitivity range and the low sen sitivity range to maintain an optimal infrared image Automatic range High sensitivity range 20 to 150 C 4 to 302 F e Low sensitivity range 0 to 650 C 32 to 1202 F 11 3 2 3 Fire mode Figure 11 3 Fire mode The fire mode is similar to the NFPA standardized firefighting mode but with a higher temperature starting point for the heat colorization It is suitable for fire scenes with high er background temperatures where there are already a lot of open flames and a high background temperature The camera automatically switches between the high sensitiv ity range and the low sensitivity range to maintain an optimal infrared image
22. argets i e enemy soldiers had to be illuminated by infrared search beams Since this involved the risk of giving away the observer s position to a similarly equipped enemy observer it is understandable that military interest in the image converter eventually faded The tactical military disadvantages of so called active i e search beam equipped ther mal imaging systems provided impetus following the 1939 45 war for extensive secret military infrared research programs into the possibilities of developing passive no search beam systems around the extremely sensitive photon detector During this peri od military secrecy regulations completely prevented disclosure of the status of infrared imaging technology This secrecy only began to be lifted in the middle of the 1950 s and from that time adequate thermal imaging devices finally began to be available to civilian science and industry 11559811 r AE 9082 9150 en US 33 A note on the technical production of this publication This publication was produced using XML the eXtensible Markup Language For more information about XML please visit http www w3 org XML A note on the typeface used in this publication This publication was typeset using Linotype Helvetica World Helvetica was designed by Max Miedinger 1910 1980 LOEF List Of Effective Files T501016 xml en US AE 9082 2013 09 23 T505471 xml en US 8080 2013 06 11 T505517 xml en US 708
23. cameras that are shipped to our service department 11559811 r AE 9082 9150 en US 7 What is the Flir K series Thank you for choosing aFlir K series camera from Flir Systems The Flir K series is a robust and reliable infrared camera series designed to perform under extremely severe conditions lt has an intuitive interface with a design that makes it easy to control even with a gloved hand The crisp and clear image helps you to navi gate through smoke and to make quick and accurate decisions Main features Extremely affordable a thermal imaging camera in every firefighting truck Flir Systems markets more thermal imaging cameras than any other manufacturer Thanks to economies of scale Flir Systems can market the Flir K series at an ex tremely affordable price Robust and reliable The Flir K series is designed to meet tough operating condi tions It can withstand a drop from 2 m 6 5 onto a concrete floor is water resistant to IP67 and is fully operating up to 85 C 185 F Clear and crisp thermal images The maintenance free uncooled microbolometer sensor produces clear and detail rich images of 240 x 180 pixels Flir K40 or up to 320 x 240 pixels Flir K50 Thermal images are presented on a large bright 4 dis play helping you to navigate and to make quick and accurate decisions Easy to use and in a gloved firefighter s hand An intuitive and simple user inter face allows you to focus on the job The
24. e battery can occur A CAUTION Applicability Cameras with one or more batteries Applicability Cameras with one or more batteries Do not put the batteries in or near a fire or into direct sunlight When the battery becomes hot the built in safety equipment becomes energized and can stop the battery charging procedure If the battery be comes hot damage can occur to the safety equipment and this can cause more heat damage or igni tion of the battery A CAUTION Applicability Cameras with one or more batteries Do not put the battery on a fire or increase the temperature of the battery with heat Damage to the bat tery and injury to persons can occur A CAUTION Applicability Cameras with one or more batteries Do not put the battery on or near fires stoves or other high temperature locations Damage to the bat tery and injury to persons can occur A CAUTION Applicability Cameras with one or more batteries Do not solder directly onto the battery Damage to the battery can occur A CAUTION Applicability Cameras with one or more batteries Do not use the battery if when you use charge or put the battery in storage there is an unusual smell from the battery the battery feels hot changes color changes shape or is in an unusual condition Speak with your sales office if one or more of these problems occurs Damage to the battery and injury to persons can occur
25. es to the camera s image archive Note The maximum number of images that can be saved in the image archive is 200 When the number of images exceed 200 images are deleted on a first in first out basis i e the 201st image will delete the 1st image the 202nd image will delete the 2nd image and so on 11 4 2 Figure 11 4 3 Procedure Follow this procedure 1 Aim the camera toward an object of interest 2 To save an image pull the trigger 11559811 r AE 9082 9150 en US 11 Operation 11 5 Connecting the camera to a computer 11 5 1 General You can connect the camera to a computer using the USB cable Once connected you can move the images from the camera s image archive to the computer You can also im port the images into our Flir Tools software A download card for Flir Tools is included in the transport case For more information about Flir Tools see the Flir Tools manual on the User Documenta tion CD ROM or on the Help menu in Flir Tools 11 5 2 Procedure Follow this procedure 1 Fold up the rubber cover at the top of the camera hj 2 Hold the metal ring firmly 3 Rotate the ring approx 110 counter clockwise aa v 4 Pull out the plastic insert A CAUTION The plastic insert has an O ring seal Do not damage the O ring seal T559811 r AE 9082 9150 en US 19 11 Operation 5 Connect the USB cable to the USB Mini B connector
26. for the fuse recommendation 2 Remove the two screws that hold the metal bracket Remove the metal bracket Use the metal bracket as a template to mark where the mounting holes should be drilled Drill the holes 6 Mount the metal bracket using the rivets and or screws that come with the in truck charger 7 Connect the cable to the cable plinth on the rear of the in truck charger Boo a Note Take note of the polarity when you connect the cable to the cable plinth 8 Route the cable so that it exits through the cable port of your choice 9 Mount the in truck charger to the metal bracket using the two screws that you re moved in Step 2 above 10 Permanently connect the cable to the fire engine s 12 24 VDC system 12 6 Charging the camera Follow this procedure 1 Pull up the top cover of the in truck charger 2 Push the camera into position 3 Push down the top cover The charging of the camera has now started and is finished when the blue light glows continuously Charging a fully depleted camera takes approximately 4 hours 11559811 r AE 9082 9150 en US 24 In truck charger optional accessory 12 7 Charging a battery separately Flir K series batteries can be charged separately using the battery charger at the lower front of the unit Follow this procedure Pull the eccentric latch on the bottom of the camera Pull out the battery from the camera Push the battery into the slot at the l
27. frared siii oen ea Sinan ee Lose eer eed eoe uus 27 14 2 1 Liquids i ir edere dee e rM iei 27 14 22 Equipmeht 25 reip i 27 14 2 3 Procedure eo 27 About Flir Systems icono pas 28 15 1 More than just an infrared camera sse 29 15 2 Sharing our knowledge sss esse ee ee eee ee 29 15 3 Supportingourcustomels 29 15 4 Afewimagesfromourfacilities 30 History of infrared technology eese 31 11559811 r AE 9082 9150 en US vi Legal disclaimer 1 1 Legal disclaimer All products manufactured by Flir Systems are warranted against defective materials and workmanship for a period of one 1 year from the delivery date of the original purchase provided such products have been under normal storage use and service and in accordance with Flir Systems instruction Uncooled handheld infrared cameras manufactured by Flir Systems are war ranted against defective materials and workmanship for a period of two 2 years from the delivery date of the original purchase provided such products have been under normal storage use and service and in accordance with Flir Systems instruction and provided that the camera has been registered within 60 days of original purchase Detectors for uncooled handheld infrared cameras manufactured by Flir Sys tems are warranted against defective materials and workmans
28. frared wavelengths Different investigators in attempting to confirm his work used various types of glass in discriminately having different transparencies in the infrared Through his later experi ments Herschel was aware of the limited transparency of glass to the newly discovered thermal radiation and he was forced to conclude that optics for the infrared would prob ably be doomed to the use of reflective elements exclusively i e plane and curved mir rors Fortunately this proved to be true only until 1830 when the Italian investigator Melloni made his great discovery that naturally occurring rock salt NaCl which was available in large enough natural crystals to be made into lenses and prisms is remark ably transparent to the infrared The result was that rock salt became the principal infra red optical material and remained so for the next hundred years until the art of synthetic crystal growing was mastered in the 1930 s Figure 16 3 Macedonio Melloni 1798 1854 Thermometers as radiation detectors remained unchallenged until 1829 the year Nobili invented the thermocouple Herschel s own thermometer could be read to 0 2 C 0 036 F and later models were able to be read to 0 05 C 0 09 F Then a break through occurred Melloni connected a number of thermocouples in series to form the first thermopile The new device was at least 40 times as sensitive as the best thermome ter of the day for detect
29. hip for a period of ten 10 years from the delivery date of the original purchase provided such products have been under normal storage use and service and in ac cordance with Flir Systems instruction and provided that the camera has been registered within 60 days of original purchase Products which are not manufactured by Flir Systems but included in sys tems delivered by Flir Systems to the original purchaser carry the warranty if any of the particular supplier only Flir Systems has no responsibility whatso ever for such products The warranty extends only to the original purchaser and is not transferable It is not applicable to any product which has been subjected to misuse neglect accident or abnormal conditions of operation Expendable parts are excluded from the warranty In the case of a defect in a product covered by this warranty the product must not be further used in order to prevent additional damage The purchaser shall promptly report any defect to Flir Systems or this warranty will not apply Flir Systems will at its option repair or replace any such defective product free of charge if upon inspection it proves to be defective in material or work manship and provided that it is returned to Flir Systems within the said one year period Flir Systems has no other obligation or liability for defects than those set forth above No other warranty is expressed or implied Flir Systems specifically disclaims the
30. howed a steady increase from the violet end to the red end This was not entirely unexpected since the Italian researcher Landriani in a similar experi ment in 1777 had observed much the same effect It was Herschel however who was the first to recognize that there must be a point where the heating effect reaches a maxi mum and that measurements confined to the visible portion of the spectrum failed to lo cate this point Figure 16 2 Marsilio Landriani 1746 1815 Moving the thermometer into the dark region beyond the red end of the spectrum Her schel confirmed that the heating continued to increase The maximum point when he found it lay well beyond the red end in what is known today as the infrared wavelengths 11559811 r AE 9082 9150 en US 31 16 History of infrared technology When Herschel revealed his discovery he referred to this new portion of the electromag netic spectrum as the thermometrical spectrum The radiation itself he sometimes re ferred to as dark heat or simply the invisible rays Ironically and contrary to popular opinion it wasn t Herschel who originated the term infrared The word only began to ap pear in print around 75 years later and it is still unclear who should receive credit as the originator Herschel s use of glass in the prism of his original experiment led to some early contro versies with his contemporaries about the actual existence of the in
31. i e IMP M ii 18 14 4 2 Elgueta 18 AAAS Procedure Jat ea RE rn EN Fe UE 18 311559811 r AE 9082 9150 en US V Table of contents 12 13 14 15 16 11 5 Connectingtihecameratoacompulter 19 A A A E 19 11 5 2 Procedure umi ade 19 11 6 Viewing saved images esse sese eee ce ee ee eee eee eree ee eee 21 11 6 1 e TTT 21 11 6 2 Procedure cocos ii 21 11 7 Changing settings eri ea lk ya Ma Le MR GAL de 22 A GONG ral sersem Aas AT 22 11 7 2 Procedure ird a 22 In truck charger optional accessory eee 23 124 Introductions E tb EE ERES 23 12 2 Parts and functions rere HERR ERE ER 23 12 8 Choosing a suitable position scs 24 12 4 Recommendedcableareaandfuse 24 12 5 X Mounting Instructions sss es ee eee eee ee ee e Hm 24 12 6 Charging the camera sss nemen 24 12 7 Charging a battery separately sss 25 12 98 Technical data eis andes zle 25 12 97 3Gleanirig oi lama ii Coto egg 25 12 10 Customer SUPPO ui 25 Technical data siii circa ilan Ka ala sk RET vag a a AERA adadan 26 Cleaning the camera css sese eee sese eee eee ree e erene anana e 27 14 1 Camera housing cables andotheritems 27 14 1 1 LUIS TT 27 14 1 2 Equipment 0r ORDRE akde a 27 14 1 3 Procedure 5o oie ce dades certas 27 14 2 In
32. implied warranties of merchantability and fitness for a particular purpose Flir Systems shall not be liable for any direct indirect special incidental or consequential loss or damage whether based on contract tort or any other legal theory This warranty shall be governed by Swedish law Any dispute controversy or claim arising out of or in connection with this war ranty shall be finally settled by arbitration in accordance with the Rules of the Arbitration Institute of the Stockholm Chamber of Commerce The place of ar bitration shall be Stockholm The language to be used in the arbitral proceed ings shall be English 1 2 Usage statistics Flir Systems reserves the right to gather anonymous usage statistics to help maintain and improve the quality of our software and services 1 3 Changes to registry The registry entry HKEY LOCAL MACHINENSYSTEM CurrentControlSet WControllLsalLmCompatibilityLevel will be automatically changed to level 2 if the Flir Camera Monitor service detects a Flir camera connected to the com puter with a USB cable The modification will only be executed if the camera device implements a remote network service that supports network logons 1 4 U S Government Regulations This product is subject to US Export Regulations Please refer to exportques tions flir com with any questions 1 5 Copyright 2013 FLIR Systems Inc All rights reserved worldwide No parts of the software including source code
33. indicator 10 Spotmeter temperature Note The green icon color indicates that the camera automatically switches between the high sensitivity range and the low sensitivity range depending on the object The blue icon color indicates that the temperature range is locked NFPA National Fire Protection Association an international non profit organization http www nfpa org 11559811 r AE 9082 9150 en US 13 11 Operation 11 1 Removing the battery 11 1 1 Procedure Follow this procedure 1 Pull the eccentric latch 2 Pull out the battery from the battery compartment T 11 2 Chargingthe battery 11 2 1 General Charge the battery for 4 hours before starting the camera for the first time or until the blue battery condition LED glows continuousiy 11 2 2 Procedure Follow this procedure 1 Putthe battery in the standalone battery charger 2 Connect the power supply cable plug to the connector on the standalone battery charger 3 Connect the power supply mains electricity plug to a mains socket 4 Disconnect the power supply cable plug when the blue battery condition LED glows continuously 11559811 r AE 9082 9150 en US 14 11 Operation 11 3 Selecting camera modes 11 3 1 General The Flir K series features five different camera modes You select camera mode by push ing the Mode button The five different camera modes are 1 NFPA firefighting mode NFPA National Fire
34. ing heat radiation capable of detecting the heat from a person standing three meters away The first so called heat picture became possible in 1840 the result of work by Sir John Herschel son of the discoverer of the infrared and a famous astronomer in his own right Based upon the differential evaporation of a thin film of oil when exposed to a heat pat tern focused upon it the thermal image could be seen by reflected light where the inter ference effects of the oil film made the image visible to the eye Sir John also managed to obtain a primitive record of the thermal image on paper which he called a thermograph 11559811 r AE 9082 9150 en US 32 16 History of infrared technology Figure 16 4 Samuel P Langley 1834 1906 The improvement of infrared detector sensitivity progressed slowly Another major break through made by Langley in 1880 was the invention of the bolometer This consisted of a thin blackened strip of platinum connected in one arm of a Wheatstone bridge circuit upon which the infrared radiation was focused and to which a sensitive galvanometer re sponded This instrument is said to have been able to detect the heat from a cow ata distance of 400 meters An English scientist Sir James Dewar first introduced the use of liquefied gases as cool ing agents such as liquid nitrogen with a temperature of 196 C 320 8 F in low tem perature research In 1892 he invented a unique vac
35. ir L t mr iit i Figure 15 1 Patent documents from the early 1960s The company has sold more than 234 000 infrared cameras worldwide for applications such as predictive maintenance R amp D non destructive testing process control and au tomation and machine vision among many others Flir Systems has three manufacturing plants in the United States Portland OR Boston MA Santa Barbara CA and one in Sweden Stockholm Since 2007 there is also a manufacturing plant in Tallinn Estonia Direct sales offices in Belgium Brazil China France Germany Great Britain Hong Kong Italy Japan Korea Sweden and the USA together with a worldwide network of agents and distributors support our internation al customer base Flir Systems is at the forefront of innovation in the infrared camera industry We anticipate market demand by constantly improving our existing cameras and developing new ones The company has set milestones in product design and development such as the intro duction of the first battery operated portable camera for industrial inspections and the first uncooled infrared camera to mention just two innovations 11559811 r AE 9082 9150 en US 28 15 About Flir Systems Figure 15 2 LEFT Thermovision Model 661 from 1969 The camera weighed approximately 25 kg 55 Ib the oscilloscope 20 kg 44 Ib and the tripod 15 kg 33 Ib The operator also needed a 220 VAC generator set and a 10 L 2
36. mera charger 3 Hole for attaching the charger housing to the metal bracket 11559811 r AE 9082 9150 en US 23 In truck charger optional accessory 4 Connectors in the cradle 5 Connector to power the charger using a standard Flir Systems power supply 6 Hole for attaching the charger housing to the metal bracket 7 LED indicator for the battery charger 8 Battery slot 9 Eccentric latch to secure the battery during charging 10 Cable port 1 of 4 11 Routing support 12 12 24 VDC cable plinth 13 Recess for the cable 14 Routing support 12 3 Choosing a suitable position Before mounting the in truck charger take a few minutes to think about a suitable position The mounting position should be protected from rain and road splash and it should be reasonably easy to install a permanent cable running from the fire engine s 12 24 VDC system to the in truck charger Additional considerations may be important e g getting access to panels and equip ment behind the in truck charger 12 4 Recommended cable area and fuse Cable area 1 5 mm No 15 AWG Fuse 5A 12 5 Mounting instructions Follow this procedure 1 Permanently install a cable running from the fire engine s 12 24 VDC system to the selected mounting position of the in truck charger Do not connect this cable to the 12 24 VDC system at this time The routing must include a fuse installed close to the battery See above
37. nt note about this manual Flir Systems issues generic manuals that cover several cameras within a model line This means that this manual may contain descriptions and explanations that do not apply to your particular camera model 11559811 r AE 9082 9150 en US 5 Customer help FLIR Customer Support Center Home Answers Aska Question Product Registration Downloads My Stuff Service FLIR Customer support Get the most out of your FLIR products Get Support for Your FLIR Products Welcome to the FLIR Customer Support Center This portal will help you as a FLIR customer to get the most out of your FLIR products The portal gives you access to The FLIR Knowledgebase Ask our support team requires registration Software and documentation requires registration FLIR service contacts Find Answers We store all resolved problems in our solution database Search by product category keywords or phrases Search by Keyword Search All Answers See All Popular Answers 4 1 General For customer help visit http support flir com 4 2 Submitting a question To submit a question to the customer help team you must be a registered user lt only takes a few minutes to register online If you only want to search the knowledgebase for existing questions and answers you do not need to be a registered user When you want to submit a question make sure that you have the following information to hand
38. ower front of the charger Secure the battery using the eccentric latch on the charger The charging of the battery has now started and is finished when the blue light glows continuously Charging a fully depleted battery takes approximately 4 hours Pon 12 8 Technical data Dimensions height x width x depth 380 mm x 180 mm x 153 mm 15 x 7 1 x 6 Weight 2 2 kg 4 8 Ib Power input 12 24 VDC Charging time camera 4 hours Charging time separate battery 4 hours Maximum current 3A Nominal current 2 3A 12 9 Cleaning N CAUTION Disconnect the in truck charger from the fire engine s 12 24 VDC system before cleaning The in truck charger can be cleaned using warm water or a weak detergent solution Do not use solvents or similar liquids 12 10 Customer support Should you experience any problems do not hesitate to contact our Customer Support at http support flir com 11559811 r AE 9082 9150 en US 25 13 Technical data For technical data on this product refer to the product catalog and or technical data sheets on the User Documentation CD ROM that comes with the product The product catalog and the datasheets are also available at http support flir com 11559811 r AE 9082 9150 en US 26 14 Cleaning the camera 14 1 Camera housing cables and other items 14 1 1 Liquids Use one of these liquids Warm water Aweak de
39. scovery was made accidentally during the search for a new optical material Sir William Herschel Royal Astronomer to King George III of England and already famous for his discovery of the planet Uranus was searching for an optical filter material to re duce the brightness of the sun s image in telescopes during solar observations While testing different samples of colored glass which gave similar reductions in brightness he was intrigued to find that some of the samples passed very little of the suns heat while others passed so much heat that he risked eye damage after only a few seconds observation Herschel was soon convinced of the necessity of setting up a systematic experiment with the objective of finding a single material that would give the desired reduction in brightness as well as the maximum reduction in heat He began the experiment by ac tually repeating Newton s prism experiment but looking for the heating effect rather than the visual distribution of intensity in the spectrum He first blackened the bulb of a sensi tive mercury in glass thermometer with ink and with this as his radiation detector he pro ceeded to test the heating effect of the various colors of the spectrum formed on the top of a table by passing sunlight through a glass prism Other thermometers placed outside the sun s rays served as controls As the blackened thermometer was moved slowly along the colors of the spectrum the temperature readings s
40. t Flir K series service 7 What is the Flir K series eseeeee eee eeeee eren 8 Quick start guide siipien 2 baski dan stes coa iara ca anke v ca oe dr aaa added aseguro ca da a 9 Parts WSUS 3 eine eene A ERES AE ERE MERE 10 8 1 Scope of delivery icc d kalaslar ZY KC YK 7972 10 8 2 lListofaccessoriesandservices 10 System parts sasiet nrnna iaden aanse oai reo aaisa pi sairaana 11 9 1 Camela EEEE ET EA e E E LA 11 OTT MEN GIC ee DE 11 9 12 Explanation Crete ren izde eae 11 9 2 lanyardstrap retractablelanyard 12 AS 12 9 22 a alae e e ala da lam aS 12 9 3 Neck sirapi sie ies Aim acted Seki ml bei A a 12 A Ge 12 9 32 Explanation sas tdci 12 Screen elements sees eyes eens ag amala sa anak daa l n damda 13 101 US at la ac 13 10 25 Explanation 13 Operation 14 11 1 Removingthebattery eee eaeeaeees 14 Tlk Procedure iile Melikesi ado es Ae be elle 14 11 2 Charging the battery misesa ee e ea m 14 AAA i a aaa 14 11 2 2 Procedure a 14 11 8 Selectingcameramodes m 15 VAST General serme te e dekan des acd dek ceci 15 11 3 2 Explanation of the different camera modes 15 11 4 Saving an Mage ie tI tai 18 TT 4 T Generals i
41. tergent solution 14 1 2 Equipment A soft cloth 14 1 3 Procedure Follow this procedure 1 Soakthe cloth in the liquid 2 Twist the cloth to remove excess liquid 3 Clean the part with the cloth N CAUTION Do not apply solvents or similar liquids to the camera the cables or other items This can cause damage 14 2 Infrared lens 14 2 1 Liquids Use one of these liquids A commercial lens cleaning liquid with more than 30 isopropyl alcohol e 96 ethyl alcohol C2H50H e DEE ether diethylether C4H19O 50 acetone dimethylketone CH3 2CO 50 ethyl alcohol by volume This liquid prevents drying marks on the lens 14 2 2 Equipment Cotton wool 14 2 8 Procedure Follow this procedure 1 Soakthe cotton wool in the liquid 2 Twist the cotton wool to remove excess liquid 3 Clean the lens one time only and discard the cotton wool A WARNING Make sure that you read all applicable MSDS Material Safety Data Sheets and warning labels on con tainers before you use a liquid the liquids can be dangerous A CAUTION Be careful when you clean the infrared lens The lens has a delicate anti reflective coating Do not clean the infrared lens too vigorously This can damage the anti reflective coating T559811 r AE 9082 9150 en US 27 15 About Flir Systems Flir Systems was established in 1978 to pioneer the development of high performance
42. uum insulating container in which it is possible to store liquefied gases for entire days The common thermos bottle used for storing hot and cold drinks is based upon his invention Between the years 1900 and 1920 the inventors of the world discovered the infrared Many patents were issued for devices to detect personnel artillery aircraft ships and even icebergs The first operating systems in the modern sense began to be developed during the 1914 18 war when both sides had research programs devoted to the military exploitation of the infrared These programs included experimental systems for enemy intrusion detection remote temperature sensing secure communications and flying tor pedo guidance An infrared search system tested during this period was able to detect an approaching airplane at a distance of 1 5 km 0 94 miles or a person more than 300 meters 984 ft away The most sensitive systems up to this time were all based upon variations of the bolome ter idea but the period between the two wars saw the development of two revolutionary new infrared detectors the image converter and the photon detector At first the image converter received the greatest attention by the military because it enabled an observer for the first time in history to literally see in the dark However the sensitivity of the im age converter was limited to the near infrared wavelengths and the most interesting mili tary t
43. ver at strong energy sources for example devices that cause laser radiation or the sun This can have an unwanted effect on the accuracy of the camera It can also cause damage to the detector in the camera A CAUTION Applicability Cameras with one or more batteries Do not attach the batteries directly to a car s cigarette lighter socket unless Flir Systems supplies a spe cific adapter to connect the batteries to a cigarette lighter socket Damage to the batteries can occur A CAUTION Applicability Cameras with one or more batteries Do not connect the positive terminal and the negative terminal of the battery to each other with a metal object such as wire Damage to the batteries can occur A CAUTION Applicability Cameras with one or more batteries Do not get water or salt water on the battery or permit the battery to become wet Damage to the bat teries can occur T559811 r AE 9082 9150 en US Warnings amp Cautions N CAUTION Applicability Cameras with one or more batteries Do not make holes in the battery with objects Damage to the battery can occur A CAUTION Applicability Cameras with one or more batteries Do not hit the battery with a hammer Damage to the battery can occur A CAUTION Applicability Cameras with one or more batteries Do not put your foot on the battery hit it or cause shocks to it Damage to th
44. y and protection devi ces which if damage occurs can cause the battery to become hot or cause an explosion or an ignition A WARNING Applicability Cameras with one or more batteries If there is a leak from the battery and you get the fluid in your eyes do not rub your eyes Flush well with water and immediately get medical care The battery fluid can cause injury to your eyes if you do not do this A WARNING Applicability Cameras with one or more batteries Do not continue to charge the battery if it does not become charged in the specified charging time If you continue to charge the battery it can become hot and cause an explosion or ignition Injury to per sons can occur A WARNING Applicability Cameras with one or more batteries Only use the correct equipment to remove the electrical power from the battery If you do not use the correct equipment you can decrease the performance or the life cycle of the battery If you do not use the correct equipment an incorrect flow of current to the battery can occur This can cause the battery to become hot or cause an explosion Injury to persons can occur A WARNING Make sure that you read all applicable MSDS Material Safety Data Sheets and warning labels on con tainers before you use a liquid The liquids can be dangerous Injury to persons can occur A CAUTION Do not point the infrared camera with or without the lens co
Download Pdf Manuals
Related Search