User Manual of Netuart Demo Board
Contents
1. Model ATC 3200 Zigbee to RS232 422 485 Converter User s Manual Introduction The ATC 3200 is a cost effective and highly integrated Serial to Zigbee wireless Converter Built on ZigBee technology the ATC 3200 is ideal for a range of applications from simple RS 232 cable replacement to sophisticated multi drop RS 485 networks and everything in between Available in RS 232 RS 422 RS 485 ZigBee is the global wireless language connecting dramatically different devices to work together and enhance everyday life The ZigBee Alliance is a non profit association of more than 280 member companies driving development of ZigBee wireless technology The Alliance promotes world wide adoption of ZigBee as the leading wirelessly networked sensing and control standard for use in energy home commercial and industrial areas Features e Utilizes globally available 2 4 GHz ISM band e Control and Configuration with UART commands e 65535 unique node addresses IDs allow multiple large networks to coexist e Programmable Transmit Power Output max 12 dBm e Complete IEEE 802 15 4 spec compliant e Typical Receiver Sensitivity 102 dBm e Typical Throughput rate 250 000 bps e Obstructed signal range to 500 meters 12dBm PA and 102dBm LNA e Multiple Low Power Operating modes e 3 in 1 RS 232 422 485 interface Max 115 2Kbps Serial interface and zigbee e Supports 4 and 2 wire RS 485 with AUTO SEND and built in terminator e Supports i2. ey ffff Check Time Unknow 2 Configure ATC 3200 Step1 Use a connector or converter to make a connection between the ATC 3200 and PC RS 232 RS 422 RS 485 E ATC 3200 PC Step2 With a fine needle through the small hole next to the power plug inside the set by holding down the switch for 5 seconds the red light flashes Equipment belonging to the state can be set Step3 Start software QR RS232 1 to N selected using a computer to connect the Master module serial port Setup Tools for 1 To N RS232 vii RS232 1 To N Setup Program Step 1 Choice Master COM Port Master Com Port NO Loms RD Step4 Click the Next button to read the ATC 3200 firmware configuration Select Master module parameters Setup Tools for 1 To N RS232 v1 1 RS232 1 To N Setup Program Step 2 Get and Setup Master s Parameters Master Module Parameters MAC Address 5152544300001003 0001003 PANID Module Type Channel E 7 Check Time Selection is complete click Write To began to set parameters Step5 When the screen appears the following screen on behalf of parameters are set Setup Tools for 1 To N RS232 v1 1 RS232 1 To N Setup Program Step 2 Get and Setup Master s Parameters Setup Setup EA te te Setup Mark Pair te Finish Network Master Parameter Parameter el 4 245 MH2 Encryption 00 No Ener 7 Baudrate Encryption Key Party Check
3. ndustrial 24 VDC power input and optional Power over Serial e Terminal block accessories for easy RS 422 485 serial wiring e Easy and powerful configuration program e Approval CE RoHS Hardware Description 1 RS 232 Pinout DB9 Male 2 RS 422 485 Pinout six Terminal from left Terminal 1 2 3 4 5 No Paso RR vn GND rrs aas ase a88 vw ono 3 Power Supply ATC 3200 Zigbee converter can adopt the product s 9V power adapter for power supply or adopt power from other DC power or device 9 24V 500 100mA 4 ATC 3200 LED indication SET Indication Zigbee Link yellow on Zigbee Link established LINK Data Sending Receiving between Serial and the Zigbee PWR Indication Power 5 Connection Diagram RS 232 Connection RS232 PC iil y i i lt DB9 Female fi A DB9 Female ATC 3200 RxD 2 3 TxD TxD 3 2 RxD GND 5 RS 422 Connection 5 GND RS 422 T 1 T 2 R 3 R 4 a ATC 3200 RS 485 Connection 485 1 485 2 Device ATC 3200 Applications e Wireless remote control e Building automation e Personal area network e Industrial control e OEM equipment e PC peripherals Configuration and Operation 1 ATC 3200 default Settings Master Com Port No com1 Slave Com Port No com1 Pan ID 5152 Channel 01 2410MHz Baud rate 9 600 Parity Check Unknow Encryption 01 Encry Encryption K
4. ow CheckTime Step6 Click the Setup Slave enter the Slave matching process Step7 Remove Master module COM Port connection Slave module Setup Tools for 1 To N RS232 v1 1 RS232 1 To N Setup Program Step 3 Change to Slave Step8 Press the pairing button Slave module until the matching light flashes Step9 Click Next enter the Slave matching images Setup Tools for 1 To N RS232 v1 1 RS232 1 To N Setup Program Step 4 Get and Setup Salve s Parameters Parent _ Module Type 00 No Enery eink e Channel Parity Check kTime 500m Write To Slave Setp10 Click the Write To Slave set the Slave parameters start Setp11 When the screen appears the following screen on behalf of parameters are set Setup Tools for 1 To N RS232 v1 1 RS232 1 To N Setup Program Step 4 Get and Setup Salve s Parameters Setup Setup Network gt Master gt Mark Pair Parameter Parameter Setup Finish Channel 04 2425MHz 00 No Enery Encryption Key 100 Parity Check 500 ms Step12 If the remaining Slave modules required settings click the Other Slave Starting from step 7 to reset
Download Pdf Manuals
Related Search