Lampifier® Anti Drop-Out Dual Wireless Microphone System
Contents
1. Figure 4 Removing Battery Cover C Opening the Battery Compartment To remove the cover press at circle 3 and slide the cover toward circle 4 Keep your fingers out of the circle 4 zone to avoid a pinch D Changing Microphone Channel Change the channel if you experience interference from another mic or a nearby wireless local area network LAN 1 Turn on the microphone and the receiver 2 Open the BATTERY COVER and locate the CHANNLE KNOB 3 Use a screwdriver to rotate the knob to a different channel 4 There are 16 detents on the knob one for each channel 5 When you rotate the knob the MIC ACTIVE LED on the receiver will blink once to indicate that the microphone is reconnected to the receiver 6 You do not need to turn off or reset the microphone or the receiver _ QU When selecting XM R l u the channel aim ay k the arrow at the N scale or in between two ae scales Fit the slotted screwdriver into I i this slot E LA Eou SS Figure 5 Changing the Microphone Channel Lampifier com 5348 N Tacoma Avenue 317 225 5509 phone Indianapolis IN 46220 317 222 1327 fax www Lampifier com help Lampifier com Lampifier Anti Drop Out Dual Wireless Microphone System Thank you for choosing the Lampifier Anti Drop Out Wireless Microphone sys tem Please read this manual carefully before using the device This system is intended for a wide range of applications such as professi2. crophone ON Press and hold 2 to 3 seconds to turn OFF If the green LED flashes replace the batteries HOUSING The wireless transmitter and batteries are inside ANTENNA Operates at 2 4GHz the same band as wireless LAN BATTERY COVER Remove this cover to access batteries and controls BATTERY COMPARTMENT Two AA batteries are required CHANNEL KNOB Rotate this knob to select one of 16 channels LAMPIFY KNOB When the receiver is in the LAMPIFY mode turn up this knob to increase dynamic compression of the audio signal When the receiver is in the NORMAL mode this knob is a volume control In either mode if the red OVERLOAD LED on the receiver flashes turn down this knob to avoid sound distortion caused by signal clipping To reduce feedback at loud volume turn down this knob At extreme volume you can also set the receiver to NORMAL mode to reduce feedback RESET BUTTON For factory use only SERS xX LRXKKKKKRK Kansa SKY POSSI TVS SOO SOS ROSS KKEKRY SOK RK SSK SSS 4 SIRLI MMM CUI X XF XA Bse OANA XX XXX XXI westatctetatctetetcte DODD KKOD Figure 2 Microphone Transmitter
3. onal music performances karaoke meetings and religious services A Carton Contents One Model 1231R Digital Wireless Receiver Two Wireless Microphones One 7 5V DC Power Adaptor One 1 4 inch phone plug cable One User s Manual Optional Adapter Cable One Optional Model 1231C 1 4 Inch to Dual XLR Output Adapter Cable December 2012 B Parts Identification Na O Or OTE G 9 10 11 12 D Q Figure 1 Receiver POWER SWITCH Press and hold 2 to 3 seconds to turn ON or OFF MIC 1 ACTIVE OVERLOAD LED Glows red when microphone 1 is turned on and ready for use Flashes when mic 1 LAMPIFY KNOB needs to be turned down to prevent signal clipping See figure 2 MIC 2 ACTIVE OVERLOAD LED Same as above for microphone 2 VOLUME 1 KNOB Turn this know to change the output volume of mic 1 VOLUME 2 KNOB Same as above for microphone 2 ANTENNA RESET BUTTON For factory use only 1 4 OUTPUT JACK Both mics signals are mixed into this mono output Use the optional 1231C Adaptor Cable to convert the output into two independent balanced XLR outputs RESET BUTTON For factory use only DC POWER Connects to the AC Adaptor for 7 5V DC center pole is MODE SWITCH 1 Selects mic 1 operating mode Lampify Mute Normal MODE SWITCH 2 Same as above for microphone 2 NRO Or Sola E BALL GRILL Protects the microphone cartridge and reduces wind noise POWER SWITCH Press to turn the mi
Download Pdf Manuals
Related Search