Wireless Three-Way Light Switch User Manual
Contents
1. INSTRUCTION GUIDE Wireless Extend A Wall Switch HW2155D Transmitter Receiver Switch Switch Bae ENCLOSED YOU WILL FIND Receiver Switch Transmitter Switch Double sided tape 12 Volt alkaline battery installed Wiring Device Screws and Wire Nuts bagged Screws for mounting Transmitter Switch TOOLS NEEDED e Small Flat head screwdriver e Tweezers INSTALLATION Four channels are available so that you can operate up to four systems at different locations around your home See channel options RECEIVER SWITCH Allows you to control an overhead light from 2 locations Warning Turn off power first by removing the fuse or switching the circuit breaker to off This product requires some knowl edge of electrical wiring and must be installed in accordance with the National Electrical Code NEC and local codes Note Not for use with existing three way circuits 1 Turn off power see above 2 Remove the faceplate of the existing wall switch 3 Remove the existing wall switch 4 Attach the green ground wire to the ground wire from the 120V line Connect power leads to the Receiver wires by twisting the wire nut clockwise over the ends Push all wiring into the outlet box Note If installed in a metal box the green ground wire and 120V line must be grounded to the box Refer to local or National Electrical Code requirements Control Switch 5 Slide the Control Switch on the Receiver Switc2. OR send the product and the dated sales receipt to Lamson amp Sessions 25701 Science Park Drive Cleveland OH 44122 USA Attn LHP Customer Service Not Covered Batteries light bulbs and other expendable items are not covered by this warranty Repair service adjustment and calibration due to misuse abuse or negligence are not covered by this warranty Unauthorized service or modification of the product or of any furnished components will void this warranty in its entirety This warranty does not include reimbursement for inconvenience installation set up time loss of use postage unauthorized service or other products used in conjunction with but are not supplied by Lamson amp Sessions All requests for replacement must include a dated sales receipt copies accepted LAMSON amp SESSIONS IS NOT LIABLE FOR LOST PROFITS INDIRECT SPECIAL EXEMPLARY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION ANY SUCH DAMAGES DUE TO IMPROPER WIRING OR MISUSE OF THE PRODUCT As some states do not allow the exclusion or limitation of incidental or consequential damages the above limitation and exclusion may not apply to you This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation This device complies
3. duct slide the Control Switch on the Receiver to the Off position TROUBLESHOOTING TIPS Problem Nothing happens when Switch is pressed Suggestions 1 Confirm that power is On to the fixture being controlled by the product 2 Verify that Control Switch on the Receiver is in the On posi tion 3 Replace bulb Note When changing a light bulb in the fixture controlled by the product slide the Control Switch on the Receiver to the Off position 4 Check that Receiver and Transmitter are set to same channel and are within 50 feet of each other 5 Check battery orientation in the Transmitter Switch or try replacing the battery Problem Light sometimes turns on off without anyone press ing Switch Suggestion If another Wireless system is on the same frequency nearby it could accidentally trigger your system If this happens change channels on the Transmitter and Receiver by following instructions below CHANGING DIGITAL CODE CHANNELS optional This product utilizes digital channels to send a signal from Transmitter to Receiver The user can change the signal if out side interference occurs If you use other wireless products in your home there is a slight possibility of interference Use the following instructions to change the current channel setting to anew setting IMPORTANT If you change the channel combination on the Transmitter you must change the combination on the Receiver If the channel c
4. h to the On position 6 Confirm that the channel settings on Receiver Switch match those on the Transmitter Switch See Changing Digital Code Channels for more information 7 Replace existing faceplate Note Do not use a metallic wall plate as it will decrease the operating range 8 Restore power TEST Position Transmitter Switch in the desired location and test operation by pushing the top of Switch for On or bottom of Switch for Off MOUNTING SWITCH TRANSMITTER Note Mounting Switch on a masonry or metal wall may reduce range A For tape mounting 1 Make sure surfaces are free of dust oil and other sub stances that could affect adhesion 2 Attach double sided tape to back of Switch housing 3 Press tape firmly to mounting surface B For screw mounting 1 Remove faceplate screws from cover place back plate where desired and mark screw locations 2 Insert mounting screws into holes in back plate and screw into place 3 Replace cover and faceplate screws SWITCH BATTERY REPLACEMENT 1 Remove faceplate screws from cover and lift cover away from back plate 2 Remove old battery 3 Install new 12 volt Type A23 alkaline battery noting polarity 4 Replace cover and screws MANUAL OVERRIDE To prevent the Receiver Switch from responding to the transmitter slide the Control Switch on the Receiver to the Off position Note When changing a light bulb in the fixture controlled by the pro
5. ombinations do not match the system will Back of Transmitter Front of Receiver CHANNEL JUMPERS Under plug Control Switch CODE OPTIONS not function 1 Turn off power to the Receiver by removing the fuse or switching the circuit breaker to Off 2 Slide the Control Switch on Receiver Switch to the Off position Locate Channel Jumpers on back of the Transmitter Switch and on front of the Receiver Channel codes are A B C amp D Select proper channel by moving jumpers with tweezers Slide the Control Switch on the Receiver Switch to the ON position 6 Reinstall Receiver and Transmitter Switch by following Installation Instructions OB w SPECIFICATIONS Detection Range Up to 50 Maximum Load 350W incandescent only Rated Voltage 120V AC 60 Hz Battery 12 volt Type A23 alkaline For indoor use only Do not use with existing three way circuits LIMITED WARRANTY The product you have purchased is guaranteed against defects in workmanship and materials for the period stated on the package Warranties implied by law are subject to the same time period limitation Some states do not allow limitations on how long an implied warranty lasts so this time limitation may not apply to you If the product fails due to a manufacturing defect during normal use return the product and dated sales receipt to the store where purchased for replacement
6. with RSS 210 of Industry Canada ALSO AVAILABLE FROM CARLON Extend A Chime lets you near youi existing wired doorbell in remote areas of your home or yard e Plug in and Battery Doorbells and Chimes e On Off Remote Switches e Touch and Automatic Lighting Controls This warranty gives you specific legal rights and you may also have other rights which vary from state to state If you have questions or need further assistance please call Lamson amp Sessions at 1 800 346 2646 Mon Fri 9 a m 4 p m EST rt ee ae 2 EN NANO 10102
Download Pdf Manuals
Related Search