Fog Fury 3000
Contents
1. ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 14 youtube com adjlighting Tel 31 45 546 85 00 Fax 31 45 546 85 992. LLC Do not discard the shipping cartoon in the trash Please recycle when ever possible SAFETY ISSUES NEVER POINT OR AIM A FOG MACHINE TOWARDS PEOPLE OR THEIR CLOTHING THIS UNIT EMITS HOT VAPOR AND SHOULD BE USED WITH THE SAME CARE THAT YOU WOULD OBSERVE WHEN USING AN ELECTRIC KETTLE OR IRON Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 2 Fog Fury 3000 Safety Precautions e Be sure to save the packing carton in the unlikely event the unit may have to be returned for service Do not spill water or other liquids into or on to your fogger Be sure that all the fog fluid is kept inside the fluid reservoir Be sure that the local power outlet match that or the required voltage for your fog machine Do not remove the top cover under any conditions There are no user serviceable parts inside Disconnect the unit s main power when left unused for long peri ods of time e Never connect this unit to a dimmer pack Do not attempt to operate this unit if it becomes damaged in anyway e Never operate this unit when it s cover is removed To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not attempt to operate this unit if the power cord has been fray ed or broken Do not attempt to remove or break off the ground prong f
3. ing to operate you fixture DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fixture DMX data is sent as serial data that trav els from fixture to fixture via the DATA IN and DATA OUT XLR ter minals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compli ant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX Operation The Fog Fury 3000 can be controlled via DMX 512 protocol The Fog Fury 3000 has 3 DMX channels The DMX address is set on the back panel Your unit and your DMX controller require a standard 3 pin XLR
4. 0 0 3 3s 31 140 131 140s 0 25 0 5 1 0 s 5 30 10 4 10 4 10s 40 150 140 150s 26 50 1 1 2 0s 31 55 11 20 21 30 21 30s 51 160 51 160s 51 75 2 1 3 0s 56 80 21 30 31 40 31 40s 61 170 61 170s 76 100 3 1 4 0s 81 105 31 40 41 50 41 50s 71 180 71 180s 101 125 4 1 5 0s 106 130 41 50 51 60 51 60s 81 190 81 190s 126 150 5 1 6 0s 131 155 51 60 61 70 61 70s 91 200 91 200s 151 175 6 1 7 0s 156 180 61 70 71 80 71 80s 201 210 201 210s 176 200 7 1 8 0s 181 205 71 80 81 90 81 90s 211 220 211 220s 201 225 8 1 9 0s 206 230 81 90 91 100 91 100s 221 230 221 230s 226 250 9 1 10 0s 231 255 91 100 101 110 101 110s 231 240 231 240s 251 255 Constant Fogging 111 120 111 120s 241 250 241 250s 121 130 121 130s 251 255 251 255s s seconds Fog Fury 3000 Proper Storage and Maintenance When storing your fog machine be sure to store it in a cool area Cover the machine so that dust does not build up on the unit When storing the machine for long periods of time it is highly advised to at least run the machine every 3 4 months Long periods of inactivity can severly shorten the life of your machine Only run water based fog juice through your machine Never run plain water vinegar or any other liquid solution through your machine Running anything other then water based fog juice will severly damage your machine ADJ Pro
5. at all disconnect and discontinue use immediately Do not attempt to con tinue pushing the remote control s activation button as this may dam age the fog machine Check the fluid level the external fuse remote connection and be sure the wall outlet is sending power If all of the above appears to be okay and the unit fails to operate correctly the unit will require service Please contact ADJ Products LLC ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 12 Fog Fury 3000 Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America including possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the product only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC w
6. button until I XXX is displayed 2 Press the UP or DOWN buttons to change the output interval 3 seconds is the lowest time while 255 seconds is longest time between output d XX This is the Dispersion time setting length of fog output 1 Press the MENU button until d XX is displayed 2 Press the UP or DOWN buttons to change the dispersion time 1 second is the lowest time while 10 seconds is longest output time ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 8 Fog Fury 3000 Constant Output Constant Fog Output Set Up 1 Press the MENU button until u XXX is displayed 2 Press the UP or DOWN buttons to set the display at u 012 or below 012 001 Next press the MENU button until 1 XXX is displayed Press the UP or DOWN buttons to set the display at 1 000 Press the timer button to turn on the timer The machine should now have constant fog output N OORA W Press the timer button again to turn off constant fog output Fog Fury 3000 DMX Mode DMX Mode Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs This function also allows you to use your fixtures as spot lights The Fog Fury 3000 has 3 DMX channels See page 11 for the DMX traits 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 Torun your fi
7. connec tor for data input and data output Figure 1 We rec ommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all pro lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Figure 1 ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 4 Fog Fury 3000 DMX Information Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR XLR Male Socket XLR Female Socket 1 Ground z 2 Cold 2 ey Figure 2 XLR Pin Configuration Pin 1 Ground Pin 2 Data Compliment negative paella alae Pin 3 Data True positive Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the fem
8. setting to ON Make sure the Slave units are all set to Master Off The Slave unit will now follow the Master Fog Fury 3000 Remote Operation Always be sure to maintain an adequate supply of American DJ Brand Fog Juice in the fluid reservoir Running the fog machine dry will cause pump failure and or clogging This is the largest cause of failure in fog and haze machines Only American DJ Fog Juice is recommended and not all fog juice is created equal Remote Operation Start by connecting the remote to the fog machine Once the machine is plugged in and turned on a red power LED on the remote will glow indicating the unit is receiving power The unit has a warm up time of about eight 8 minutes After the unit has warmed up a GREEN LED on the remote will light indicating the unit is ready to emit fog To emit fog simply press the button on the remote for desired length of time If the GREEN LED is on and fog does not come out after holding the button down for 30 seconds check the fluid tank and make sure you have enough fog juice Caution Before removing or replacing the remote control unit disconnect the power supply ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 10 Fog Fury 3000 DMX Chart Channel 1 Volume Channel 2 Interval Channel 3 Duration DMX Value Action Time DMX Value Action Time DMX Value Action Time DMX Value Action Time 0 4
9. Caution Fog Machines may set off Smoke Alarms Rev 7 15 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indi rect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent assembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all
10. LC www adj com Fog Fury 3000 Instruction Manual Page 6 Fog Fury 3000 Description The new Fog Fury 3000 fog machine features a fog juice level sensor When the fog juice level is low a LED below the reservoir will flash When the fog juice level reaches a lower level a bult in sensor inside the reser voir will automatically shut off the pump This will greatly expand the life of the pump The new Fog Fury 3000 fog machine included a revolution ary new heating element that has been specially designed to prevent excessive particle build up that can cause premature fogger failure The fog machine also includes a remote control that may be removed for periods on non use Fog Fury 3000 Set Up Open the shipping carton and carefully remove the unit from the shipping carton 2 Be sure to remove all the packing material especially around the nozzle 3 Set the fog machine on a flat dry surface Locate the included bracket from the package and install it using the supplied hardware to the side casing Note The bracket is an optional accessory and may not be used if desired however if you intend to suspend the unit from truss the brack et must be used A Fill the fog fluid reservoir with American DJ brand fog juice Place the feeder tube with the filter deep inside the reservoir and tighten the cap 5 Firmly attach the remote control unit to the rear remote control socket on the unit 6 Plug the unit in to a matching
11. ale XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems O and interference It is always advisable A p to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion Conductor 3 Pin XLR Female Out 5 Pin XLR Male In Ground Shield Pin 1 Pin 1 Data Compliment sional Data True signal Pin 3 Pin 3 Not Used Do Not Use Not Used Do Not Use ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 5 Fog Fury 3000 Layout j i ji j j iii 1 A Bracket I Up B Handle J Down C Fog Fluid Tank K DMX 3 pin XLR Output D Power Switch L DMX 3 pin XLR Input E Timer ON OFF M Control Socket Connection F Fog Switch N NFB G LED display O Electric Power Cord H Menu P Bracket Knob with lock ADJ Products L
12. ducts LLC www adj com Fog Fury 3000 Instruction Manual Page 11 Fog Fury 3000 Warranty Registration The Fog Fury 3000 fog machine carries a one year 365 days lim ited warranty Please fill out the enclosed warranty card to validate your purchase All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number The R A number must be clearly written on the out side of the return package A brief description of the problem as well as the R A number must also be written down on a piece of paper and included in the shipping container If the unit is under warranty you must provide a copy of your proof of purchase invoice You may obtain a R A number by contacting customer support at 800 322 6337 Fog Fury 3000 Trouble Shooting e If machine is running low on fog juice the LED below the fluid rese voir will flash slowly and the LCD display will show Er 1 If the thermal sensor wire has disconnected or is acting abnormal the LED below the fluid resevoir will flash quickly and the LCD dis play will show Er 2 e If the communication of thermo circuit and main control circuit has faulted the LED below the fluid resevoir will flash intermittently and the LCD display will show Er 3 Note Even though the LED is below the fluid reservoir you can see the LED color through fluid tank If you experience low fog output pump noise or no fog output
13. electrical equipment from power when not in use Thank you Fog Fury 3000 Introduction Introduction Congratulations you have just purchased one of the most reliable fog machines on the market today The Fog Fury 3000 commercial fog machine have been designed to perform reliably for years when the guidelines in this booklet are followed Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit These instructions contain important information regarding safety during use and maintenance Customer Support ADJ Products LLC provides a toll free customer support line to provide set up help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions For service related issue please contact ADJ Products LLC Service Hours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail support americandj com To purchase parts online visit http parts americandj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures war ranty In the unlikely event your unit may require service please contact ADJ Products
14. es Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 1 Year 365 Days Limited Warranty excluding laser diodes which have a 6 month limited warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty batteries which have a 180 day limited war ranty Only the L E D s carry a 2 year warranty excluding StarTec Series which a carries a 1 Year Limited Warranty e ADJ DMX Controllers 2 Year 730 Days Limited Warranty excluding faders and tact switches ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 13 Fog Fury 3000 Specifications MODEL Fog Fury 3000 VOLTAGE 120v or 230V 50 60Hz HEATER 1500W POWER CONSUMPTION 1600W WEIGHT 25 Lbs 11 28 Kgs 18 75 x 13 75 x 12 75 475 x 345 x 321 mm 20A 120V 10A 230V 8 Minutes 5 Liter 21000 cubic feet per minute Water Base American DJ Fog Juice 3 DMX Channels Not to exceed 6 hours turned on Voltage is preset at the factory and may not be changed ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Follow Us On Junostraat 2 f Mw 6468 EW Kerkrade Netherlands facebook com americandj service adjgroup eu www adj eu twitter com americandj
15. ill pay return shipping charges only to a designated point within the United States If the entire instrument is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a service contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were
16. manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strob
17. power supply At this time the fluid reservoir will glow red this indicates that the unit is heating up Wait about eight minutes for the fogger to reach normal operating temperature When it has reached the temperature the reservoir will glow green 7 Either press the remote button to emit fog or use the manual button on the rear of the unit to emit fog See the next pages for timer control and DMX control 8 Follow the operating instructions on the next page for proper operation NOTE If the LED under the reservoir begins to flash this indicates that fog juice fluid is low ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 7 Fog Fury 3000 System Menu A XXX DMX Address Setting XXX represents the dis played DMX address 1 Press the MENU UP or DOWN buttons until A XXX is dis played XXX represents the current address that is displayed 2 Press the UP or DOWN buttons to change find your desired address TIMER MODE These menu settings are for Timer mode Make these setting before activating the Timer Mode U XXX This is the Volume setting output intensity 1 Press the MENU button until u XXX is displayed 2 Press the UP or DOWN buttons to change the output inten sity 5 is the lowest output while 100 is highest output XXX This is the Interval setting set time in between fog output Note Heating will factor into the interval set ting 1 Press the MENU
18. rom the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection e Never block the ventilation holes Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall This unit is intended for indoor use only use of this product out doors voids all warranties Always mount this unit in a safe and stable matter e Please route your power cord out of the way of foot traffic Power cords should be routed so they are not likely to be walked on pinched by items placed upon or against them The unit should only be serviced by qualified service personnel when A The power supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the unit C The unit has been exposed to rain or water D The appliance does not appear to operate normally or exhibits a marked change in performance ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 3 Fog Fury 3000 DMX Information Power Supply Before plugging your unit in be sure the source volt age in your area matches the required voltage for your ADJ Fog Fury 3000 The ADJ Fog Fury 3000 is available in a 120v and 230v version Because line voltage may vary from venue to venue you should be sure your unit voltage matches the wall outlet voltage before attempt
19. xture in DMX mode press the MENU button until A XXX is displayed XXX represents the current displayed ad dress Use the UP or DOWN buttons to select your desired DMX address Please see page 11 for DMX values and traits After you have set your DMX address plug in the fixture via the XLR connections to any standard DMX controller C2 ADJ Products LLC www adj com Fog Fury 3000 Instruction Manual Page 9 Fog Fury 3000 Master Slave Set Up Master Slave Configuration This function will allows you to link units together to run in a Master Slave mode In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units built in programs Any unit can act as a Master or as a Slave however only one unit can be pro grammed to act as the Master Master Slave Connections and Settings 1 Daisy chain your units via the XLR connector on the rear of the unit Use standard XLR data cables to link your units together Remember that the Male XLR connector is the input and the Female XLR con nector is the ouput The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only 2 Connect the first Slave unit to the Master 3 On the Master unit press the MENU button until M XXX is dis played XXX representing either ON or OFF Use the UP or DOWN button to change the
Download Pdf Manuals
Related Search