Laser Show System
Contents
1. Two Heads Laser Light User Manual Thank you for purchasing this product To optimize the performance of this product prior to use please read these operating instructions carefully to get yourself familiar with the basic operation of this unit Please keep the manual in safe price for future reference This unit has been tested at our factory before being shipped to you there is no assembly required Once after received this product please take and put carefully And check cautiously that whether the product was damaged or not during the transportation Checking Parts Please check if the following parts are included 1 x Laser Light 1 x Power cable 1 x User manual Danger Laser Radiation Avoid direct eye exposure Laser radiation can cause eye damage or skin damage All protective measures for a safe operation of this laser must be applied Installation 1 Please check the voltage whether is the same with the one showed on the equipment or not 2 It must ask for the technical person and set the light safety when installation And let the light beam at the suitable angle 3 When install this equipment please make sure there s no flammable surfaces decorated things etc within at least 2 5M and maintain minimum distance of 0 5M from the equipment to the walls 4 Please make sure that there s no other equipment or decorating materials obstructed the exhaust fan and the vent pipe 5 Products should be install immo2. 9 10 ON 1 2 3 4 5 6 7 OFF Channel Instruction Channel Value Description 0 64 Close light CH1 64 127 Auto play 128 191 Sound active 192 255 Patterns control CH2 0 255 Choose patterns 0 63 Choose patterns size CH3 64 127 From small to large speed up rate 128 191 From large to small speed up rate 192 255 Large small large speed up rate 0 127 Choose rotation angle CH4 128 191 Auto clockwise rotation speed up rate 192 255 Auto anti clockwise rotation speed up rate CH5 0 127 Choose horizontal position 128 255 Horizontal move speed up rate CH6 0 127 Choose Vertical position 128 255 Vertical move speed up rate CH7 0 127 Choose horizontal roll position 128 255 Horizontal roll speed up rate CH8 0 127 Choose Vertical roll position 128 255 Vertical roll speed up rate Maintenance Maintenance should be performed every 15 day period by using a sponge which is dipped with alcohol rather than wet cloth or other chemical liquid to clean the mirror Always disconnect from the mains when the device is not in use or before cleaning it Warning Power must be disconnected before maintenance or repair Do not look at the light source directly To prevent or reduce the risk of electrical shock or fire do not expose this unit to high temperature rain or moisture Note Don t separate laser machine from laser power and repair them
3. bility 6 In case of safety it s very important that to connect the earth with line Attention 1 Please do not open the bottom cover yourself without permission Operate it accord the user manual Call the technician when the machine breaks down 2 Please do not see the laser beam directly to avoid any damage 3 Before connect or disconnect the power please adjust the luminance of the laser diode to the least to avoid any damage to the laser diode 4 This unit should be keep dry do not use in the rain and dusty environment It can be use in the outdoor with the water proof cover protector 5 Set the light immobility and try to avoid strong shake or hit 6 Prevent dust into the equipment to avoid problems 7 Please keep that there s no other equipment or decorating materials obstructed the exhaust fan and the vent pipe when the equipment was working 8 Before connect power check the plug is immobility or not power line should be connect well 9 Please do not open or close the equipment frequently that s to avoid any affect to the life span of the laser diode and try the best to avoid the long time working 10 Due to the characteristic of the laser diode after four hours working it should be close at least 25 minutes until the laser diode cooling then work again 11 Don t touch the light or draw the power line when your hand was wet And do not pull the electronic power line 12 Maintain the distance at least 3M above from the
4. by yourself otherwise no good repair service will be supplied Technical Specifications 1 Power Supply AC 110 240V 2 Rated Power 30W 3 Laser Power Green 50mw 532nm Red 150mw 650nm 4 Working Mode Sound Active Auto play DMX51 2 Master Slave 5 Control Signal DMX512 Signal 6 DMX Control Channels 8 Channels 7 Scanner System Step Motor 8 Operating Temperature 1 35 9 Storage Temperature 10 60 10 Warm Up Time lt 15 min 11 Laser Classification 3b 12 Modulation TTL 13 Net Weight 3 6KG 14 Gross Weight 4 3KG 15 Packing Size 43 25 17cm Declaration This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual We cannot be made liable for damages caused by incorrect installations and unskilled operation Warranty Card This product is made of high brightness transistor We will provide 1 year warranty under the condition that user has operated the light normally and lifetime service We won t provide warranty if the damage is caused by artificial or force majeure event Cost of fittings should be charged by user if product need maintenance after 1 year Please cut this warranty card and shipped it along with the product to our factory when applying for warranty Product Purchasing date Code of invoi
5. ce Warranty date From To User s name Add Company Tel
6. equipment to the object 13 This equipment does not have any parts can repair for the users please do not open the equipment 14 When the laser diode became dim or damaged please contact the dealer timely 15 When you want to retransfer the products you d better use the original package to shockproof Function Instructions 1 When dip switch No 10 is set to the ON position the unit works in auto mode 2 When all dip switches are set to the OFF position the unit works in sound active mode 3 Auto play Master slave synchronization when master laser dip switch setting to No 10 the light will run the settled program automatically meanwhile it will have DMX512 signal s output Just one light could be settled to be master Setting slave you should put dip switch No 1 in on 4 Sound active Master slave synchronization when all dip switches are turned off the light is in sound active mode In this condition the light will run program along with music meanwhile it will have DMX512 signal s output Just one light could be settled to be master Setting slave you should put dip switch No 1 in on 5 Address code function mode setting Mode Binary code ON 1 IDMX 512 mode Slave mode 1 9 Setting address code 10 OFF 2 Sound active mode Master modell 10 OFF 3 Auto play mode Master mode 1 9 OFF 10 ON 4 Square test pattern 9 10 ON 1 2 3 4 5 6 7 8 OFF 5 Dot text pattern 8
Download Pdf Manuals
Related Search